Pull exception table generation updates from Ingo Molnar:
"The biggest change here is to allow the build-time sorting of the
exception table, to speed up booting. This is achieved by the
architecture enabling BUILDTIME_EXTABLE_SORT. This option is enabled
for x86 and MIPS currently.
On x86 a number of fixes and changes were needed to allow build-time
sorting of the exception table, in particular a relocation invariant
exception table format was needed. This required the abstracting out
of exception table protocol and the removal of 20 years of accumulated
assumptions about the x86 exception table format.
While at it, this tree also cleans up various other aspects of
exception handling, such as early(er) exception handling for
rdmsr_safe() et al.
All in one, as the result of these changes the x86 exception code is
now pretty nice and modern. As an added bonus any regressions in this
code will be early and violent crashes, so if you see any of those,
you'll know whom to blame!"
Fix up trivial conflicts in arch/{mips,x86}/Kconfig files due to nearby
modifications of other core architecture options.
* 'x86-extable-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (35 commits)
Revert "x86, extable: Disable presorted exception table for now"
scripts/sortextable: Handle relative entries, and other cleanups
x86, extable: Switch to relative exception table entries
x86, extable: Disable presorted exception table for now
x86, extable: Add _ASM_EXTABLE_EX() macro
x86, extable: Remove open-coded exception table entries in arch/x86/ia32/ia32entry.S
x86, extable: Remove open-coded exception table entries in arch/x86/include/asm/xsave.h
x86, extable: Remove open-coded exception table entries in arch/x86/include/asm/kvm_host.h
x86, extable: Remove the now-unused __ASM_EX_SEC macros
x86, extable: Remove open-coded exception table entries in arch/x86/xen/xen-asm_32.S
x86, extable: Remove open-coded exception table entries in arch/x86/um/checksum_32.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/usercopy_32.c
x86, extable: Remove open-coded exception table entries in arch/x86/lib/putuser.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/getuser.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/csum-copy_64.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/copy_user_nocache_64.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/copy_user_64.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/checksum_32.S
x86, extable: Remove open-coded exception table entries in arch/x86/kernel/test_rodata.c
x86, extable: Remove open-coded exception table entries in arch/x86/kernel/entry_64.S
...
A new option is added to the relocs tool called '--realmode'.
This option causes the generation of 16-bit segment relocations
and 32-bit linear relocations for the real-mode code. When
the real-mode code is moved to the low-memory during kernel
initialization, these relocation entries can be used to
relocate the code properly.
In the assembly code 16-bit segment relocations must be relative
to the 'real_mode_seg' absolute symbol. Linear relocations must be
relative to a symbol prefixed with 'pa_'.
16-bit segment relocation is used to load cs:ip in 16-bit code.
Linear relocations are used in the 32-bit code for relocatable
data references. They are declared in the linker script of the
real-mode code.
The relocs tool is moved to arch/x86/tools/relocs.c, and added new
target archscripts that can be used to build scripts needed building
an architecture. be compiled before building the arch/x86 tree.
[ hpa: accelerating this because it detects invalid absolute
relocations, a serious bug in binutils 2.22.52.0.x which currently
produces bad kernels. ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-2-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
x86 is now using relative rather than absolute addresses in its
exception table, so we add a sorter for these. If there are
relocations on the __ex_table section, they are redundant and probably
incorrect after the sort, so they are zeroed out leaving them valid
and consistent.
Also use the unaligned safe accessors from tools/{be,le}_byteshift.h
Signed-off-by: David Daney <david.daney@cavium.com>
Link: http://lkml.kernel.org/r/1335291795-26693-2-git-send-email-ddaney.cavm@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
While changing our build system over to use the headers_install target
as part of our klibc build, the following message started showing up in
our logs:
make[2]: `scripts/unifdef' is up to date.
It turns out that the build blindly invokes a recursive make on this
target, which causes make to emit this message when the target is
already up to date. This isn't seen for most targets as the rest of the
build relies primarily on the default target and on PHONY targets when
invoking make recursively.
Silence the above message when building unifdef as part of
headers_install by hiding it behind a new PHONY target called
"build_unifdef" that has an empty recipe.
Signed-off-by: Mike Waychison <mikew@google.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This patch adds the support for the C version of recordmcount and
compile times show ~ 12% improvement.
After verifying this works, other archs can add:
HAVE_C_MCOUNT_RECORD
in its Kconfig and it will use the C version of recordmcount
instead of the perl version.
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kbuild@vger.kernel.org
Cc: John Reiser <jreiser@bitwagon.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Many years ago when this driver was written, it had a use, but these
days it's nothing but trouble and distributions should not enable it
in any situation.
Pretty much every console device a sparc machine could see has a
bonafide real driver, making the PROM console hack unnecessary.
If any new device shows up, we should write a driver instead of
depending upon this crutch to save us. We've been able to take care
of this even when no chip documentation exists (sunxvr500, sunxvr2500)
so there are no excuses.
Signed-off-by: David S. Miller <davem@davemloft.net>
The powerpc kernel always requires an Open Firmware like device tree
to supply device information. On systems without OF, this comes from
a flattened device tree blob. This blob is usually generated by dtc,
a tool which compiles a text description of the device tree into the
flattened format used by the kernel. Sometimes, the bootwrapper makes
small changes to the pre-compiled device tree blob (e.g. filling in
the size of RAM). To do this it uses the libfdt library.
Because these are only used on powerpc, the code for both these tools
is included under arch/powerpc/boot (these were imported and are
periodically updated from the upstream dtc tree).
However, the microblaze architecture, currently being prepared for
merging to mainline also uses dtc to produce device tree blobs. A few
other archs have also mentioned some interest in using dtc.
Therefore, this patch moves dtc and libfdt from arch/powerpc into
scripts, where it can be used by any architecture.
The vast bulk of this patch is a literal move, the rest is adjusting
the various Makefiles to use dtc and libfdt correctly from their new
locations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 8b249b6856.
This 'fix' is not necessary; we just need to undo the damage caused
accidentally by Igor/Mauro in 4b29631db3
("V4L/DVB (9533): cx88: Add support for TurboSight TBS8910 DVB-S PCI card")
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Rafael reported:
I get the following error from 'make modules_install' on my test boxes:
HOSTCC firmware/ihex2fw
/home/rafael/src/linux-2.6/firmware/ihex2fw.c:268: fatal error: opening dependency file firmware/.ihex2fw.d: Read-only file system
compilation terminated.
make[3]: *** [firmware/ihex2fw] Error 1
make[2]: *** [_modinst_post] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
where the configuration is that the kernel is compiled on a build box
with 'make O=<destdir> -j5' and then <destdir> is mounted over NFS read-only by
each test box (full path to this directory is the same on the build box and on
the test boxes). Then, I cd into <destdir>, run 'make modules_install' and get
the error above.
The issue turns out to be that we when we install firmware pick
up the list of firmware blobs from firmware/Makefile.
And this triggers the Makefile rules to update ihex2fw.
There were two solutions for this issue:
1) Move the list of firmware blobs to a separate file
2) Avoid ihex2fw rebuild by moving it to scripts
As I seriously beleive that the list of firmware blobs should be
done in a fundamental different way solution 2) was selected.
Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David Woodhouse <dwmw2@infradead.org>
In August 2006 I posted a patch generating a minimal SELinux policy. This
week, David P. Quigley posted an updated version of that as a patch against
the kernel. It also had nice logic for auto-installing the policy.
Following is David's original patch intro (preserved especially
bc it has stats on the generated policies):
se interested in the changes there were only two significant
changes. The first is that the iteration through the list of classes
used NULL as a sentinel value. The problem with this is that the
class_to_string array actually has NULL entries in its table as place
holders for the user space object classes.
The second change was that it would seem at some point the initial sids
table was NULL terminated. This is no longer the case so that iteration
has to be done on array length instead of looking for NULL.
Some statistics on the policy that it generates:
The policy consists of 523 lines which contain no blank lines. Of those
523 lines 453 of them are class, permission, and initial sid
definitions. These lines are usually little to no concern to the policy
developer since they will not be adding object classes or permissions.
Of the remaining 70 lines there is one type, one role, and one user
statement. The remaining lines are broken into three portions. The first
group are TE allow rules which make up 29 of the remaining lines, the
second is assignment of labels to the initial sids which consist of 27
lines, and file system labeling statements which are the remaining 11.
In addition to the policy.conf generated there is a single file_contexts
file containing two lines which labels the entire system with base_t.
This policy generates a policy.23 binary that is 7920 bytes.
(then a few versions later...):
The new policy is 587 lines (stripped of blank lines) with 476 of those
lines being the boilerplate that I mentioned last time. The remaining
111 lines have the 3 lines for type, user, and role, 70 lines for the
allow rules (one for each object class including user space object
classes), 27 lines to assign types to the initial sids, and 11 lines for
file system labeling. The policy binary is 9194 bytes.
Changelog:
Aug 26: Added Documentation/SELinux.txt
Aug 26: Incorporated a set of comments by Stephen Smalley:
1. auto-setup SELINUXTYPE=dummy
2. don't auto-install if selinux is enabled with
non-dummy policy
3. don't re-compute policy version
4. /sbin/setfiles not /usr/sbin/setfiles
Aug 22: As per JMorris comments, made sure make distclean
cleans up the mdp directory.
Removed a check for file_contexts which is now
created in the same file as the check, making it
superfluous.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
The driver for /proc/config.gz consumes rather a lot of memory and it is in
fact possible to build it as a module.
In some ways this is a bit risky, because the .config which is used for
compiling kernel/configs.c isn't necessarily the same as the .config which was
used to build vmlinux.
But OTOH the potential memory savings are decent, and it'd be fairly dumb to
build your configs.o with a different .config.
Signed-off-by: Andrew Morton <akpm@google.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on patch from: Magnus Damm <magnus@valinux.co.jp>
This has the advantage that all section mismatch checks are run regardless
of modules being enabled or not.
When running modpost on vmlinux output:
MODPOST vmlinux
When running modpost on modules output count of modules like this:
MODPOST 5 modules
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
