EHCI enable power pin is inverted (active high) in comparison
to vanilla beagle which is active low. Handle this case conditionally.
Without this fix, Beagle XM 4 port EHCI will not function and no
networking will be available
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support twl4030 keypad and gpio keys on IGEP v2.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second MMC channel (used by the WLAN/BT module) is not linked to
power regulator. This causes the WLAN/BT module to fail being detected if
CONFIG_REGULATOR_DUMMY is not set.
This patch adds the two regulators that actually feed the WLAN/BT module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module has one EHCI interface on board using
USB2HS port. GPIO183 is used as PHY reset.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At latest mainline commit 0c21e3aaf6, omap2plus build is broken. This
patch is trivial fix for the missed usb clock node for CK_3430ES2PLUS
flag update.
CHK include/generated/compile.h
CC arch/arm/mach-omap2/clock3xxx_data.o
arch/arm/mach-omap2/clock3xxx_data.c:3289: error: 'CK_3430ES2' undeclared
here (not in a function)
make[1]: *** [arch/arm/mach-omap2/clock3xxx_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated mask to include CK_36XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SMSC 3320 USB PHY on the OMAP4 Pandaboard needs a 19.2 MHz
reference clock. This clock is provided from the OMAP4's fref_clk3
pad.
Recent changes to clock44xx_data.c made the clock framework aware
of the existence of these fref_clk[i] lines. If the option
CONFIG_OMAP_RESET_CLOCKS is enabled in the kernel, then the
clock framework will turn these clocks off during bootup.
Explicitly request and keep this clock enabled at init for the
Pandaboard, so that the PHY receives this clock at all times.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap2plus_defocnfig build breaks when customised with only ARCH_OMAP4
selected. This is because common files make references to the functions
which are defined only for omap2xxx and omap3xxx.
LD .tmp_vmlinux1
arch/arm/mach-omap2/built-in.o: In function `pm_dbg_regset_store':
arch/arm/mach-omap2/pm-debug.c:335: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap2_pm_dump':
arch/arm/mach-omap2/pm-debug.c:121: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:123: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:124: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:125: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap_prcm_arch_reset':
arch/arm/mach-omap2/prcm.c:106: undefined reference to `omap2_prm_set_mod_reg_bits'
arch/arm/mach-omap2/prcm.c:108: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap_prcm_get_reset_sources':
arch/arm/mach-omap2/prcm.c:53: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `clkdm_clear_all_wkdeps':
arch/arm/mach-omap2/clockdomain.c:545: undefined reference to `omap2_prm_clear_mod_reg_bits'
arch/arm/mach-omap2/built-in.o: In function `clkdm_del_wkdep':
arch/arm/mach-omap2/clockdomain.c:475: undefined reference to `omap2_prm_clear_mod_reg_bits'
arch/arm/mach-omap2/built-in.o: In function `clkdm_read_wkdep':
arch/arm/mach-omap2/clockdomain.c:511: undefined reference to `omap2_prm_read_mod_bits_shift'
arch/arm/mach-omap2/built-in.o: In function `clkdm_add_wkdep':
arch/arm/mach-omap2/clockdomain.c:440: undefined reference to `omap2_prm_set_mod_reg_bits'
make: *** [.tmp_vmlinux1] Error 1
This patch adds stubs for these functions so that build continues to work.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
struct clockdomain member clktrctrl_mask is available for only for OMAP2
and OMAP3 architectures. Technially it is also used only for these archs
but this breaks the build with custom OMAP4 configuration.
CC arch/arm/mach-omap2/clockdomain.o
arch/arm/mach-omap2/clockdomain.c: In function '_enable_hwsup':
arch/arm/mach-omap2/clockdomain.c:251: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:254: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function '_disable_hwsup':
arch/arm/mach-omap2/clockdomain.c:277: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:280: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_sleep':
arch/arm/mach-omap2/clockdomain.c:744: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_wakeup':
arch/arm/mach-omap2/clockdomain.c:789: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_clk_enable':
arch/arm/mach-omap2/clockdomain.c:922: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:926: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_clk_disable':
arch/arm/mach-omap2/clockdomain.c:994: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:998: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
make[1]: *** [arch/arm/mach-omap2/clockdomain.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Fix the build break by dropping the #ifdef as suggested by Paul Walmsley
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap_pm_runtime_suspend and omap_pm_runtime_resume are used
as function pointers and does not really need to be exposed
to the world.
Fixes sparse warnings:
arch/arm/mach-omap2/pm_bus.c:23:5: warning: symbol 'omap_pm_runtime_suspend' was not declared. Should it be static?
arch/arm/mach-omap2/pm_bus.c:40:5: warning: symbol 'omap_pm_runtime_resume' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
twl_init functions are declared in pm.h and used in pm.c
pm.h header defining the protos need to be included to
ensure that omap_twl.c has consistent function definition.
This fixes sparse warning:
arch/arm/mach-omap2/omap_twl.c:237:12: warning: symbol 'omap4_twl_init' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:256:12: warning: symbol 'omap3_twl_init' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The uv_to_vsel, vsel_to_uv functions don't need to be exposed to the
world as they are used as function pointers. make them static.
Fixes sparse warnings:
arch/arm/mach-omap2/omap_twl.c:63:15: warning: symbol 'twl4030_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:68:4: warning: symbol 'twl4030_uv_to_vsel' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:73:15: warning: symbol 'twl6030_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:105:4: warning: symbol 'twl6030_uv_to_vsel' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap_enable_smartreflex_on_init is meant to be used by boards
which would like to have SR enabled by default on the platform, while
omap_devinit_smartreflex is used by pm code, the protos are defined
in pm.h. This header should be included to ensure that sr_device
function definitions match the prototypes.
including pm.h fixes the sparse warnings (with CONFIG_OMAP_SMARTREFLEX=y):
arch/arm/mach-omap2/sr_device.c:138:13: warning: symbol 'omap_enable_smartreflex_on_init' was not declared. Should it be static?
arch/arm/mach-omap2/sr_device.c:143:12: warning: symbol 'omap_devinit_smartreflex' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
omap2_wd_timer_disable is declared in wdtimer.h and used by hwmod
function pointers for usage, the header inclusion is necessary
to ensure that the prototype and function remains consistent.
omap_wdt_latency is passed as a pointer and does not need global scope
Fixes sparse warnings:
arch/arm/mach-omap2/devices.c:981:31: warning: symbol 'omap_wdt_latency' was not declared. Should it be static?
arch/arm/mach-omap2/wd_timer.c:27:5: warning: symbol 'omap2_wd_timer_disable' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
igep3_flash_init is not used beyond the scope of the file, make it
static instead.
Fixes sparse warning:
arch/arm/mach-omap2/board-igep0030.c:106:13: warning: symbol 'igep3_flash_init' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_zoom_wlan_data and zoom2_set_hs_extmute are not used beyond
the scope of zoom-peripherals directly, instead pointers are used.
make them static instead.
Fixes sparse warnings:
arch/arm/mach-omap2/board-zoom-peripherals.c:193:29: warning: symbol 'omap_zoom_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:245:6: warning: symbol 'zoom2_set_hs_extmute' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux data is passed by pointers to mux.c from the SoC specific
mux file, these variables dont really need to be global scope.
This fixes the following sparse warnings:
arch/arm/mach-omap2/mux44xx.c:547:29: warning: symbol 'omap4_core_cbl_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux44xx.c:1265:29: warning: symbol 'omap4_core_cbs_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux44xx.c:1549:29: warning: symbol 'omap4_wkup_cbl_cbs_ball' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
memcpy() copies 8 bytes too much (omap_mux_entry vs. omap_mux). Correct
by replacing memcpy() with struct assignment, which is safer.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits)
ARM: DMA: add support for DMA debugging
ARM: PL011: add DMA burst threshold support for ST variants
ARM: PL011: Add support for transmit DMA
ARM: PL011: Ensure IRQs are disabled in UART interrupt handler
ARM: PL011: Separate hardware FIFO size from TTY FIFO size
ARM: PL011: Allow better handling of vendor data
ARM: PL011: Ensure error flags are clear at startup
ARM: PL011: include revision number in boot-time port printk
ARM: vexpress: add sched_clock() for Versatile Express
ARM i.MX53: Make MX53 EVK bootable
ARM i.MX53: Some bug fix about MX53 MSL code
ARM: 6607/1: sa1100: Update platform device registration
ARM: 6606/1: sa1100: Fix platform device registration
ARM i.MX51: rename IPU irqs
ARM i.MX51: Add ipu clock support
ARM: imx/mx27_3ds: Add PMIC support
ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn()
mx51: fix usb clock support
MX51: Add support for usb host 2
arch/arm/plat-mxc/ehci.c: fix errors/typos
...
In order to be fully aligned with the Python generator output,
change a couple of fields.
- Add tab in class structures to align attributes
- Add a comma at the end of the following line to simplify
the generation by having always the same eol:
".pre_shutdown = &omap2_wd_timer_disable,"
- Add a blank line before the first entry of the
omap44xx_hwmods array.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The merge of the DMA series on top of the already modified
omap_hwmod_data_44xx.c put the dma_system structures at
the wrong position in the file.
Re-order it properly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The merge of the SR series on top of the already modified
omap_hwmod_data_44xx.c moved the smartreflex structures at the wrong
position in the file.
- Re-order the structures properly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the missing SIDLE_SMART_WKUP flag in idlemodes field of
the smartreflex sysconfig structure.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Thara Gopinath <thara@ti.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit fcf173e451
(add names for IRQs in structure resource)
forgot to take care of tusb6010 making it
fail to probe due to a missing resource.
Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517/05 Craneboard has one EHCI interface on board using port1.
GPIO35 is used as power enable.
GPIO38 is used as port1 PHY reset.
History:
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%253A%2BAdd%2BUSB%2BEHCI%2Bsupport&q=b
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap_serial_init_port so we can let the serial code handle the
remuxing of the RX pads. Note that this patch alone is not enough
and additional GPIO related patches are needed.
Only initialize uart3_rx_irrx pin, the other uart pins can be
stay static.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow hwmod state changes to mux pads based on the state changes.
By default, only enable and disable the pads. In some rare cases
dynamic remuxing for the idles states is needed, this can be done
by passing the enable, idle, and off pads from board-*.c file along
with OMAP_DEVICE_PAD_REMUX flag.
Thanks to Paul Walmsley <paul@booyaka.com> for the comments on the
hwmod related changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows adding hwmod specific pads dynamically during the
platform device init.
Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do this by splitting _omap_mux_init_signal as it already has most
of the necessary features.
Based on an earlier patch by Dan Murphy <dmurphy@ti.com>.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When CONFIG_SUSPEND is not enabled, none of the system PM methods are
used, so do not compile them in.
Thanks to Charles Manning for reporting the problem and proposing
an initial patch.
Reported-by: Charles Manning <manningc2@actrix.gen.nz>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch extends the smartreflex framework to support
OMAP4. The changes are minor like compiling smartreflex Kconfig
option for OMAP4 also, and a couple of OMAP4 checks in
the smartreflex framework.
The change in sr_device.c where new logic has to be introduced
for reading the efuse registers is due to the fact that in OMAP4
the efuse registers are 24 bit aligned. A __raw_readl will
fail for non-32 bit aligned address and hence the 8-bit read
and shift.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the hwmod details for OMAP4 smartreflex modules.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default the system boots up at nominal voltage for every
voltage domain in the system. This patch puts vdd_mpu, vdd_iva
and vdd_core to the correct boot up voltage as per the opp tables
specified. This patch implements this by matching the rate of
the main clock of the voltage domain with the opp table and
picking up the correct voltage.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has three scalable voltage domains vdd_mpu, vdd_iva
and vdd_core. This patch adds the voltage tables and other
configurable voltage processor and voltage controller
settings to control these three scalable domains in OMAP4.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
TWL6030 is the power IC used along with OMAP4 in OMAP4 SDPs,
blaze boards and panda boards. This patch registers the OMAP4
PMIC specific information with the voltage layer.
This also involves implementing a different formula for
voltage to vsel and vsel to voltage calculations from
TWL4030.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default the system boots up at nominal voltage for every
voltage domain in the system. This patch puts VDD1 and VDD2
to the correct boot up voltage as per the opp tables specified.
This patch implements this by matching the rate of the main clock
of the voltage domain with the opp table and picking up the correct
voltage.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds debug support to the voltage and smartreflex drivers.
This means a whole bunch of voltage processor and smartreflex
parameters are now visible through the pm debugfs.
The voltage parameters can be viewed at
/debug/voltage/vdd_<x>/<parameter>
and the smartreflex parameters can be viewed at
/debug/voltage/vdd_<x>/smartreflex/<parameter>
Also smartreflex n-target values are now exposed out at
/debug/voltage/vdd_<x>/smartreflex/nvalue/<voltage>
This is a read-write interface which means user has the
flexibility to change the n-target values for any opp.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch registers the TWL4030 PMIC specific informtion
with the voltage driver. Failing this patch the voltage driver
is unware of the formula to use for vsel to voltage and vice versa
conversion and lot of other PMIC dependent parameters.
This file is based on the arch/arm/plat-omap opp_twl_tpl.c file
by Paul Walmsley. The original file is replaced by this file.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Smartreflex Class3 implementation continuously monitors
silicon performance and instructs the Voltage Processors
to increase or decrease the voltage.
This patch adds smartreflex class 3 driver. This driver hooks
up with the generic smartreflex driver smartreflex.c to abstract
out class specific implementations out of the generic driver.
Class3 driver is chosen as the default class driver for smartreflex.
If any other class driver needs to be implemented, the init of that
driver should be called from the board file. That way the new class driver
will over-ride the Class3 driver.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the smartreflex hwmod data for OMAP3430
and OMAP3630.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
