o If tx and rx resources are not available, during set mac request.
Then this request wont be passed to firmware and it will be added to
driver mac list and will never make it to firmware.
So if resources are not available, don't add it to driver mac list.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o While unloading driver or resetting the context, tx ring was not
getting free.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix ethtool link test for NX3031 chip.
o Remove unused code from phy interrupt callback
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Dump registers such as tx ring and rx ring counter, firmware state,
niu regs, etc. which can be useful for debugging purpose.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Unified firmware image size can be < 1 MB
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support pci error detection and recovery.
o Refactor suspend and resume code, to share with io_error_detected,
and slot_reset callbacks
o NX_NEED_AER device state added, to synchronize with firmware
recovery.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In case of tx timeout, firmare may be healthy, but some pci-func may
see no response from it. Force firmware reset, if some pci-func
explicitly requests so.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o pci device should be disable at the end and it should be enable first.
o Interface should be attached(netif_device_attach()) irrespective
of its state.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netxen driver is doing this bogus thing to create a control file.
This fails if device doesn't exist, and overall is a bad way to do
the module parameter. Rather than fix borked code, just rewrite.
Just using a writeable module parameter of 0/1 is the correct way
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unified firmware image may not contain MN type of firmware.
Driver should fall back to NOMN firmware type instead
of going to flash.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o netif_running() check for enabling interrupt at end of napi poll is
not enough to cover firmwar recovery. Instead test __NX_DEV_UP bit.
o Avoid re-entry into to netxen_nic_down() with __NX_DEV_UP bit check.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o To prevent race conditions with other reset events.
During suspend/resume and firmware recovery, acquire rtnl_lock,
while changing interface state.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle few corner cases in firmware hang detection and recovery:
o Don't mark device state as READY, till handshake with
firmware is done.
o During probe, if start_firmware fails, restore reference
count.
o Don't increment refernce count, if start_firmware fails
during firmware reset.
o Clear __NX_RESETTING bit, incase of fatal error or tempeature
reaches critical limit so that pci remove() doesn't poll on
this bit.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver maps only some part of the MMIO bar 0 in case of
NX2031. This is sufficient for tx and rx by the driver.
When debug tools need to access resources in
unmapped regions, driver needs to map these on the fly
in order to complete read/write request.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch "fix memory initialization:5d521fd36de4e61" didn't got merge.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Along with netdev->perm_addr, mac address will be
maintained in device private structure.
o Device limitation: We need to set mac address when ever
interface comes up.
In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address.
But bonding driver set netdev->dev_addr field to its original value,
after enslaving interfaces.
When ever active slave changes, it swap dev_addr of inactive slave with active.
Yet it doesn't notify driver about change in netdev->dev_addr.
As netxen driver need to set mac addr when ever interface comes up,
it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel crashes, if promisc mode set without disabling rx queue.
Before changing mode in NX2031 chip, wait till rx queue drains.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting memory during initialization, skip this memory
block during driver probe.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCI vendor and device IDs for QLE8240 and QLE8242
CNA devices. CNA devices will have separate driver.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_FIRMWARE hints for various firmware file types,
required by different chip revisions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI vendor and device IDs for QLE8240 and QLE8242
CNA devices.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor code to calculate and set indirect access
window for control registers in 2MB address space
(NX3031 or newer). Use void __iomem * data type for
absolute pci addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extracting firmware from a unified
file format which embeds firmware images for all chip
revisions. Fallback to orginal file formats if new
image is not found.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_MODULES=n:
drivers/net/netxen/netxen_nic_main.c:2751: error: dereferencing pointer to incomplete type
drivers/net/netxen/netxen_nic_main.c:2764: error: dereferencing pointer to incomplete type
Also needs addition of <linux/sysfs.h> for sysfs function prototypes or
stubs when CONFIG_SYSFS=n.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old code assumed board config version in the flash to be 1.
When this will get changed by tools, driver just refuses to
attach. This is unnecessary since driver does not have to
parse board config structure directly (maintained by firmware).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware hang detection and recovery (reset) need to
be disabled for diagnostic tools, which can run
some disruptive tests.
This adds a driver level control to turn off this
feature by diag tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use -EIO or -EINVAL as error codes, these can get passed up
to applications (tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for different windowing scheme for on chip
memory in future chip revisions. This is required by
diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions need different chip reset sequence
and firmware initialization.
Also clean up some never used debug code.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions of the chip have 128 bit memory
transactions. Require drivers to implement rmw
in case of sub-128 bit accesses by driver. This
is mostly used by diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs entries to enable register and memory access
for diagnostic tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since register and onboard memory access has separate
window registers, they need not be kept under same lock.
Also, memory is always accessed from process context
(mostly for firmware init and diagnostic tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common variables crb_win, ocm_win for all revisions of chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access to on chip memory, this is used by
debug and diagnostic tools only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub 64-bit / unaligned access to oncard memory was only used
by old diagnostic tools, causes some intermittent issues when
memory controller agent is used. The new access method was
added by commit ea6828b8aa
("netxen: improve pci memory access"). Firmware init anyway
uses 8-byte strides.
This also fixes address/offset calculation for NX2031 context
memory (SIU). For NX3031, SIU uses same register offsets
as packet memory (MIU).
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful firmware init, return instead of
falling to error path (leading to detach) after
resuming to D0 state. This was broken in recent
firmware reset rehaul.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix minor bug in netdev tx timeout handling which could
always lead to firmware reset instead of pci function reset.
netxen_nic_reset_context() requires __NX_RESETTING bit
cleared.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add QLogic copyright, add linux-driver@qlogic.com to
MAINTAINERS.
o Delete old contact information.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redesign tx timeout handling in line with new firmware
reset design that co-ordinates with other PCI function
drivers.
o For NX3031, first try to reset PCI function's own
context before requesting firmware reset.
o For NX2031, since firmware heartbit is not supported
directly request firmware reset.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release file firmware when no firmware reset is required.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Access on card memory through memory controller (agent)
rather than moving small pci window around. Clean up the
code for moving windows around.
o Restrict memory accesss to 64 bit, currently only firmware
download uses this.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 8 byte strides for firmware download into card
memory since oncard memory controller needs 8 byte
(64 bit) accesses. This avoids unnecessary rmw cycles.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_INET is disabled, netxen has a build failure:
netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr'
so make that function just an empty stub when CONFIG_INET=n.
(not "inline" since that conflicts with other declarations of it)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the offset of vlan_TCI field in cmd_desc_type0.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in checking dest ip has support before
programming destip addresses.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Combine netxen_get_firmware_info(), netxen_check_options()
so that they are updated every time firmware is reset.
o Set dma mask everytime firmware is reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For registers accessed in fast path (interrupt / softirq)
avoid expensive I/O address translation. These registers
are directly mapped in PCI bar 0 and do not require
any window checks.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reprogram local IP addresses after firmware is reset
or after resuming from suspend.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement state machine to detect firmware hung state
and recover. Since firmware will be shared by all PCI
functions that have different class drivers (NIC or
FCOE or iSCSI), explicit hardware based serialization
is required for initializing firmware.
o Used global scratchpad register to maintain device
reference count. Every probed pci function adds to
ref count.
o Implement timer (delayed work) for each pci func
that checks firmware heartbit every 5 sec and detaches
itself if firmware is dead. Last detaching function
reloads firmware. Other functions wait for firmware
init, and re-attach themselves.
Heartbit is not supported by NX2031 firmware.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unwind allocations and release file firmware when
when firmware load fails.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a perpetual while() loop in unwinding partial
mapped tx skb on dma mapping failure.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate calls to netxen_napi_add().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alloc 12k skbuffs so that firmware can aggregate more
packets into one buffer. This doesn't raise memory
consumption since 9k skbs use 16k slab cache anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is put in bridged mode, destination mac
addresses are unknown to firmware. So packets take a slow
path (lower priority) in firmware reducing performance.
Firmware can cache limited number of remote unicast mac
addresses for certain interval, if "dynamic mac learning"
mode is enabled.
Driver needs to enable this "mac learning" mode in firmware.
Currently this is done through net device class sysfs entry,
possibly this can also be done upon netlink notifications to
from bridge.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all MAC/PHY access functions into netxen_nic_hw.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement common function for locking/unlocking 8 hardware
semaphores used for serializing access to shared resouces
on a NIC board by different PCI functions.
As by definition, callers of these semaphore API can be
put to sleep till the semaphore is locked.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code for phy access on unreleased NX2031 based quad-gig board.
NX3031 based production quad-gig boards do not require direct phy
access by driver.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate register definitions in netxen_nic_hdr.h
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.
Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all tx skb mapping code into netxen_map_tx_skb().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netxen_need_fw_reset() return 0 [ implies firmware is up
and running], still go through dma mask check, etc.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool -K knob to control LRO in firmware.
LRO path is completely separated from GRO, LRO packets
are still fed with netif_receive_skb().
Also fix ethtool statistics to include LRO packets.
Also use correct message type while configuring interrupt coalescing.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Defer napi resouce allocation to device attach.
o Free napi resources and delete napi during detach.
This ensures right behavior across firmware reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove private workqueue in the driver, move all
scheduled tasks to keventd workqueues. This makes
ports (interfaces) of same / different NIC boards
independent, in terms of their link watchdog and
reset tasks.
o Move quick checks for link status and temperature
in timer callback, schedule watchdog task only if
link status changed or temperature reached critical
threshold.
This also fixes deadlock when thermal panic occurs,
watchdog work was flushing workqueue that it was
sitting on.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to handle aggregate packets from firmware.
Local TCP flows are automatically identified by firmware
based on the dest IP hash added by driver for local IP
addresses.
The packets are sent down on the jumbo rx ring.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary offsetof calulations on these structures:
netxen_board_info, netxen_user_old_info, netxen_new_user_info.
The offsets into the flash are fixed, don't need to be calculated.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of remaining header length in TSO
over vlan device case. This was inadvertently missed
out in patch 028afe7198 ("netxen: add vlan
tx acceleration support").
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dma mask calculation that caps at 63-bit addressing even
when firmware advertises full 64-bit support.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap dest IP hashing code with #ifdef CONFIG_INET,
this feature makes no sense without INET, but other
driver can still work.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool -G to tune rx and tx ring sizes
per interface basis.
This is only supported for NX3031 based cards.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable vlan tx acceleration for NX3031 if firmware advertises
capability.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request 1532 bytes skb data size for NX3031. NX2031 firmware
needs 1760 sized buffers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all net_device initialization into one function
netxen_setup_netdev().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NX2031 firmware version will never be > 4.0.0, so replace
(adapter->fw_major < 4) checks with pci revision ID check.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move all tso / checksum offload code into netxen_tso_check().
o optimize the tso header copy into simple loop.
o clean up unnecessary unions from cmd_desc_type0 struct.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
