If user misconfigures ingress and causes a redirection loop, don't
overwhelm the log. This is also a error case so make it unlikely.
Found by inspection, luckily not in real system.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With conn-track zones and probably with different network
namespaces, the netfilter logic needs to be re-calculated
on packet receive. If the netfilter logic is not reset,
it will not be recalculated properly. This patch adds
the nf_reset logic to dev_forward_skb.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/vhost/net.c
net/bridge/br_device.c
Fix merge conflict in drivers/vhost/net.c with guidance from
Stephen Rothwell.
Revert the effects of net-2.6 commit 573201f36f
since net-next-2.6 has fixes that make bridge netpoll work properly thus
we don't need it disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since struct netdev_queue tx_bytes/tx_packets/tx_dropped are already
protected by _xmit_lock, its easy to convert these fields to u64 instead
of unsigned long.
This completes 64bit stats for devices using them (vlan, macvlan, ...)
Strictly, we could avoid the locking in dev_txq_stats_fold() on 64bit
arches, but its slow path and we prefer keep it simple.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.
The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix problem in reading the tx_queue recorded in a socket. In
dev_pick_tx, the TX queue is read by doing a check with
sk_tx_queue_recorded on the socket, followed by a sk_tx_queue_get.
The problem is that there is not mutual exclusion across these
calls in the socket so it it is possible that the queue in the
sock can be invalidated after sk_tx_queue_recorded is called so
that sk_tx_queue get returns -1, which sets 65535 in queue_index
and thus dev_pick_tx returns 65536 which is a bogus queue and
can cause crash in dev_queue_xmit.
We fix this by only calling sk_tx_queue_get which does the proper
checks. The interface is that sk_tx_queue_get returns the TX queue
if the sock argument is non-NULL and TX queue is recorded, else it
returns -1. sk_tx_queue_recorded is no longer used so it can be
completely removed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fc6055a5ba (net: Introduce skb_orphan_try()) added early
orphaning of skbs.
This unfortunately added a performance regression in skb_tx_hash() in
case of stacked devices (bonding, vlans, ...)
Since skb->sk is now NULL, we cannot access sk->sk_hash anymore to
spread tx packets to multiple NIC queues on multiqueue devices.
skb_tx_hash() in this case only uses skb->protocol, same value for all
flows.
skb_orphan_try() can copy sk->sk_hash into skb->rxhash and skb_tx_hash()
can use this saved sk_hash value to compute its internal hash value.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document that dev_get_stats() returns the same stats pointer it was
given. Remove const qualification from the returned pointer since the
caller may do what it likes with that structure.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be1f3c2c02 "net: Enable 64-bit
net device statistics on 32-bit architectures" I redefined struct
net_device_stats so that it could be used in a union with struct
rtnl_link_stats64, avoiding the need for explicit copying or
conversion between the two. However, this is unsafe because there is
no locking required and no lock consistently held around calls to
dev_get_stats() and use of the statistics structure it returns.
In commit 28172739f0 "net: fix 64 bit
counters on 32 bit arches" Eric Dumazet dealt with that problem by
requiring callers of dev_get_stats() to provide storage for the
result. This means that the net_device::stats64 field and the padding
in struct net_device_stats are now redundant, so remove them.
Update the comment on net_device_ops::ndo_get_stats64 to reflect its
new usage.
Change dev_txq_stats_fold() to use struct rtnl_link_stats64, since
that is what all its callers are really using and it is no longer
going to be compatible with struct net_device_stats.
Eric Dumazet suggested the separate function for the structure
conversion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduces an x86 defconfig text and data ~2k.
text is smaller, data is larger.
$ size vmlinux*
text data bss dec hex filename
7198862 720112 1366288 9285262 8dae8e vmlinux
7205273 716016 1366288 9287577 8db799 vmlinux.device_h
Uses %pV and struct va_format
Format arguments are verified before printk
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.
The flow for this is,
dev_queue_xmit()
dev_pick_tx()
skb_tx_hash() => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash
skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues. When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.
This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only noticed by people that are not doing everything correct in
the first place.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_needs_gso() is checked twice in the TX path once,
before submitting the skb to the qdisc and once after
it is dequeued from the qdisc just before calling
ndo_hard_start(). This opens a window for a user to
change the gso/tso or tx checksum settings that can
cause netif_needs_gso to be true in one check and false
in the other.
Specifically, changing TX checksum setting may cause
the warning in skb_gso_segment() to be triggered if
the checksum is calculated earlier.
This consolidates the netif_needs_gso() calls so that
the stack only checks if gso is needed in
dev_hard_start_xmit().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register net_bridge_port pointer as rx_handler data pointer. As br_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a bridge port. Also rcuized pointers are now correctly
dereferenced in br_fdb.c and in netfilter parts.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add possibility to register rx_handler data pointer along with a rx_handler.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct rtnl_link_stats64 as the statistics structure.
On 32-bit architectures, insert 32 bits of padding after/before each
field of struct net_device_stats to make its layout compatible with
struct rtnl_link_stats64. Add an anonymous union in net_device; move
stats into the union and add struct rtnl_link_stats64 stats64.
Add net_device_ops::ndo_get_stats64, implementations of which will
return a pointer to struct rtnl_link_stats64. Drivers that implement
this operation must not update the structure asynchronously.
Change dev_get_stats() to call ndo_get_stats64 if available, and to
return a pointer to struct rtnl_link_stats64. Change callers of
dev_get_stats() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop(). This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.
For example,
vlanx -> bond0 -> ethx
will be dropped in the vlan path and not delivered to any
packet handlers at all. However,
bond0 -> vlanx -> ethx
and
bond0 -> ethx
will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.
This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv(). Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly. This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.
I have tested the following 4 configurations in failover modes
and load balancing modes.
# bond0 -> ethx
# vlanx -> bond0 -> ethx
# bond0 -> vlanx -> ethx
# bond0 -> ethx
|
vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/591416
There are a number of network drivers (bridge, bonding, etc) that are not yet
receive multi-queue enabled and use alloc_netdev(), so don't print a
num_rx_queues imbalance warning in that case.
Also, only print the warning once for those drivers that _are_ multi-queue
enabled.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
- dev_get_by_flags() changed to dev_get_by_flags_rcu()
- ipv6_sock_ac_join() dont touch dev & idev refcounts
- ipv6_sock_ac_drop() dont touch dev & idev refcounts
- ipv6_sock_ac_close() dont touch dev & idev refcounts
- ipv6_dev_ac_dec() dount touch idev refcount
- ipv6_chk_acast_addr() dont touch idev refcount
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra assertion to allow packet munging only when there are
no other ptypes listening which may have worked around an old bug
is unnecessary. It is sufficient to check if the skb is cloned before
trampling on it. Thanks to Herbert Xu for being persistent and patient
in getting this across.
[Note that cloning checks and assertions are the general rule used
by tc actions (documentation/networking/tc-actions-env-rules.txt)].
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can avoid an unecessary cache miss by checking if the skb is non-linear
before accessing gso_size/gso_type in skb_warn_if_lro, the same can also be
done to avoid a cache miss on nr_frags if data_len is 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What this patch does is it removes two receive frame hooks (for bridge and for
macvlan) from __netif_receive_skb. These are replaced them with a single
hook for both. It only supports one hook per device because it makes no
sense to do bridging and macvlan on the same device.
Then a network driver (of virtual netdev like macvlan or bridge) can register
an rx_handler for needed net device.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When many cpus compete for sending frames on a given qdisc, the qdisc
spinlock suffers from very high contention.
The cpu owning __QDISC_STATE_RUNNING bit has same priority to acquire
the lock, and cannot dequeue packets fast enough, since it must wait for
this lock for each dequeued packet.
One solution to this problem is to force all cpus spinning on a second
lock before trying to get the main lock, when/if they see
__QDISC_STATE_RUNNING already set.
The owning cpu then compete with at most one other cpu for the main
lock, allowing for higher dequeueing rate.
Based on a previous patch from Alexander Duyck. I added the heuristic to
avoid the atomic in fast path, and put the new lock far away from the
cache line used by the dequeue worker. Also try to release the busylock
lock as late as possible.
Tests with following script gave a boost from ~50.000 pps to ~600.000
pps on a dual quad core machine (E5450 @3.00GHz), tg3 driver.
(A single netperf flow can reach ~800.000 pps on this platform)
for j in `seq 0 3`; do
for i in `seq 0 7`; do
netperf -H 192.168.0.1 -t UDP_STREAM -l 60 -N -T $i -- -m 6 &
done
done
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a skb is received on an inactive bond that does not meet
the special cases checked for by skb_bond_should_drop it should
only be delivered to exact matches as the comment in
netif_receive_skb() says.
However because null_or_bond could also be null this is not
always true. This patch renames null_or_bond to orig_or_bond
and initializes it to orig_dev. This keeps the intent of
null_or_bond to pass frames received on VLAN interfaces stacked
on bonding interfaces without invalidating the statement for
null_or_orig.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three helpers to manipulate QDISC_STATE_RUNNIG flag, that a
second patch will move on another location.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll does an interesting work in zap_completion_queue(), but this was
before we did skb orphaning before delivering packets to device.
It now makes sense to add a test in dev_kfree_skb_irq() to not queue a
skb if already orphaned, and to remove netpoll zap_completion_queue() as
a bonus.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves 224 bytes of text on my machine.
__this_cpu_inc() generates a single instruction, using no scratch
registers :
65 ff 04 25 a8 30 01 00 incl %gs:0x130a8
instead of :
48 c7 c2 80 30 01 00 mov $0x13080,%rdx
65 48 8b 04 25 88 ea 00 00 mov %gs:0xea88,%rax
83 44 10 28 01 addl $0x1,0x28(%rax,%rdx,1)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
drivers/net/usb/asix.c: Fix pointer cast.
be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
proc_dointvec: write a single value
hso: add support for new products
Phonet: fix potential use-after-free in pep_sock_close()
ath9k: remove VEOL support for ad-hoc
ath9k: change beacon allocation to prefer the first beacon slot
sock.h: fix kernel-doc warning
cls_cgroup: Fix build error when built-in
macvlan: do proper cleanup in macvlan_common_newlink() V2
be2net: Bug fix in init code in probe
net/dccp: expansion of error code size
ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
wireless: fix sta_info.h kernel-doc warnings
wireless: fix mac80211.h kernel-doc warnings
iwlwifi: testing the wrong variable in iwl_add_bssid_station()
ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
ath9k_htc: dereferencing before check in hif_usb_tx_cb()
rt2x00: Fix rt2800usb TX descriptor writing.
rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
...
the commit:
commit d90310243f
Author: Octavian Purdila <opurdila@ixiacom.com>
Date: Wed Nov 18 02:36:59 2009 +0000
net: device name allocation cleanups
introduced a bug when there is a hash collision making impossible
to rename a device with eth%d. This bug is very hard to reproduce
and appears rarely.
The problem is coming from we don't pass a temporary buffer to
__dev_alloc_name but 'dev->name' which is modified by the function.
A detailed explanation is here:
http://marc.info/?l=linux-netdev&m=127417784011987&w=2
Changelog:
V2 : replaced strings comparison by pointers comparison
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit aaf8cdc34d.
Drivers like the ipw2100 call device_create_group when they
are initialized and device_remove_group when they are shutdown.
Moving them between namespaces deletes their sysfs groups early.
In particular the following call chain results.
netdev_unregister_kobject -> device_del -> kobject_del -> sysfs_remove_dir
With sysfs_remove_dir recursively deleting all of it's subdirectories,
and nothing adding them back.
Ouch!
Therefore we need to call something that ultimate calls sysfs_mv_dir
as that sysfs function can move sysfs directories between namespaces
without deleting their subdirectories or their contents. Allowing
us to avoid placing extra boiler plate into every driver that does
something interesting with sysfs.
Currently the function that provides that capability is device_rename.
That is the code works without nasty side effects as originally written.
So remove the misguided fix for moving devices between namespaces. The
bug in the kobject layer that inspired it has now been recognized and
fixed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some issues introduced in batch skb dequeuing for input_pkt_queue.
The primary issue it that the queue head must be incremented only
after a packet has been processed, that is only after
__netif_receive_skb has been called. This is needed for the mechanism
to prevent OOO packet in RFS. Also when flushing the input_pkt_queue
and process_queue, the process queue should be done first to prevent
OOO packets.
Because the input_pkt_queue has been effectively split into two queues,
the calculation of the tail ptr is no longer correct. The correct value
would be head+input_pkt_queue->len+process_queue->len. To avoid
this calculation we added an explict input_queue_tail in softnet_data.
The tail value is simply incremented when queuing to input_pkt_queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_SMP=y, then we own a queue spinlock, we can avoid the atomic
test_and_set_bit() from napi_schedule_prep().
We now have same number of atomic ops per netif_rx() calls than with
pre-RPS kernel.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With RPS inclusion, skb timestamping is not consistent in RX path.
If netif_receive_skb() is used, its deferred after RPS dispatch.
If netif_rx() is used, its done before RPS dispatch.
This can give strange tcpdump timestamps results.
I think timestamping should be done as soon as possible in the receive
path, to get meaningful values (ie timestamps taken at the time packet
was delivered by NIC driver to our stack), even if NAPI already can
defer timestamping a bit (RPS can help to reduce the gap)
Tom Herbert prefer to sample timestamps after RPS dispatch. In case
sampling is expensive (HPET/acpi_pm on x86), this makes sense.
Let admins switch from one mode to another, using a new
sysctl, /proc/sys/net/core/netdev_tstamp_prequeue
Its default value (1), means timestamps are taken as soon as possible,
before backlog queueing, giving accurate timestamps.
Setting a 0 value permits to sample timestamps when processing backlog,
after RPS dispatch, to lower the load of the pre-RPS cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there's null check here and also again in the hook. Looking at bridge bits
which are simmilar, port structure is rcu_dereferenced right away in
handle_bridge and passed to hook. Looks nicer.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce ____napi_schedule() helper for callers in irq disabled
contexts. rps_trigger_softirq() becomes a leaf function.
Use container_of() in process_backlog() instead of accessing per_cpu
address.
Use a custom inlined version of __napi_complete() in process_backlog()
to avoid one locked instruction :
only current cpu owns and manipulates this napi,
and NAPI_STATE_SCHED is the only possible flag set on backlog.
we can use a plain write instead of clear_bit(),
and we dont need an smp_mb() memory barrier, since RPS is on,
backlog is protected by a spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of congestion, netif_rx() frees the skb, so we must assume
dev_forward_skb() also consume skb.
Bug introduced by commit 445409602c
(veth: move loopback logic to common location)
We must change dev_forward_skb() to always consume skb, and veth to not
double free it.
Bug report : http://marc.info/?l=linux-netdev&m=127310770900442&w=3
Reported-by: Martín Ferrari <martin.ferrari@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per cpu variable softnet_data.total was shared between IRQ and SoftIRQ context
without any protection. And enqueue_to_backlog should update the netdev_rx_stat
of the target CPU.
This patch renames softnet_data.total to softnet_data.processed: the number of
packets processed in uppper levels(IP stacks).
softnet_stat data is moved into softnet_data.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
include/linux/netdevice.h | 17 +++++++----------
net/core/dev.c | 26 ++++++++++++--------------
net/sched/sch_generic.c | 2 +-
3 files changed, 20 insertions(+), 25 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batch skb dequeueing from softnet input_pkt_queue to reduce potential lock
contention when RPS is enabled.
Note: in the worst case, the number of packets in a softnet_data may
be double of netdev_max_backlog.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reimplement softnet_data.output_queue as a FIFO queue to keep the
fairness among the qdiscs rescheduled.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
----
include/linux/netdevice.h | 1 +
net/core/dev.c | 22 ++++++++++++----------
2 files changed, 13 insertions(+), 10 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
optimize rps_get_cpu().
don't initialize ports when we can get the ports. one memory access
for ports than two.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way GSO packets don't get handled differently.
With help from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
If some skb are queued to our backlog, we are delaying IPI sending at
the end of net_rx_action(), increasing latencies. This defeats the
queueing, since we want to quickly dispatch packets to the pool of
worker cpus, then eventually deeply process our packets.
It's better to send IPI before processing our packets in upper layers,
from process_backlog().
Change the _and_disable_irq suffix to _and_enable_irq(), since we enable
local irq in net_rps_action(), sorry for the confusion.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point, skb->destructor is not the original one (stored in
DEV_GSO_CB(skb)->destructor)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since netdev_chain is guarded by rtnl_lock, ASSERT_RTNL should be
present here to make sure that all callers of call_netdevice_notifiers
does the locking properly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we compute a software skb->rxhash, we can generate a consistent
hash : Its value will be the same in both flow directions.
This helps some workloads, like conntracking, since the same state needs
to be accessed in both directions.
tbench + RFS + this patch gives better results than tbench with default
kernel configuration (no RPS, no RFS)
Also fixed some sparse warnings.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct softnet_data holds many queues, so consistent use "sd" name
instead of "queue" is better.
Adds a rps_ipi_queued() helper to cleanup enqueue_to_backlog()
Adds a _and_irq_disable suffix to net_rps_action() name, as David
suggested.
incr_input_queue_head() becomes input_queue_head_incr()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_rps_action() is a bit expensive on NR_CPUS=64..4096 kernels, even if
RPS is not active.
Tom Herbert used two bitmasks to hold information needed to send IPI,
but a single LIFO list seems more appropriate.
Move all RPS logic into net_rps_action() to cleanup net_rx_action() code
(remove two ifdefs)
Move rps_remote_softirq_cpus into softnet_data to share its first cache
line, filling an existing hole.
In a future patch, we could call net_rps_action() from process_backlog()
to make sure we send IPI before handling this cpu backlog.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmitted skb might be attached to a socket and a destructor, for
memory accounting purposes.
Traditionally, this destructor is called at tx completion time, when skb
is freed.
When tx completion is performed by another cpu than the sender, this
forces some cache lines to change ownership. XPS was an attempt to give
tx completion to initial cpu.
David idea is to call destructor right before giving skb to device (call
to ndo_start_xmit()). Because device queues are usually small, orphaning
skb before tx completion is not a big deal. Some drivers already do
this, we could do it in upper level.
There is one known exception to this early orphaning, called tx
timestamping. It needs to keep a reference to socket until device can
give a hardware or software timestamp.
This patch adds a skb_orphan_try() helper, to centralize all exceptions
to early orphaning in one spot, and use it in dev_hard_start_xmit().
"tbench 16" results on a Nehalem machine (2 X5570 @ 2.93GHz)
before: Throughput 4428.9 MB/sec 16 procs
after: Throughput 4448.14 MB/sec 16 procs
UDP should get even better results, its destructor being more complex,
since SOCK_USE_WRITE_QUEUE is not set (four atomic ops instead of one)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- There is no point to enforce a time limit in process_backlog(), since
other napi instances dont follow same rule. We can exit after only one
packet processed...
The normal quota of 64 packets per napi instance should be the norm, and
net_rx_action() already has its own time limit.
Note : /proc/net/core/dev_weight can be used to tune this 64 default
value.
- Use DEFINE_PER_CPU_ALIGNED for softnet_data definition.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements receive flow steering (RFS). RFS steers
received packets for layer 3 and 4 processing to the CPU where
the application for the corresponding flow is running. RFS is an
extension of Receive Packet Steering (RPS).
The basic idea of RFS is that when an application calls recvmsg
(or sendmsg) the application's running CPU is stored in a hash
table that is indexed by the connection's rxhash which is stored in
the socket structure. The rxhash is passed in skb's received on
the connection from netif_receive_skb. For each received packet,
the associated rxhash is used to look up the CPU in the hash table,
if a valid CPU is set then the packet is steered to that CPU using
the RPS mechanisms.
The convolution of the simple approach is that it would potentially
allow OOO packets. If threads are thrashing around CPUs or multiple
threads are trying to read from the same sockets, a quickly changing
CPU value in the hash table could cause rampant OOO packets--
we consider this a non-starter.
To avoid OOO packets, this solution implements two types of hash
tables: rps_sock_flow_table and rps_dev_flow_table.
rps_sock_table is a global hash table. Each entry is just a CPU
number and it is populated in recvmsg and sendmsg as described above.
This table contains the "desired" CPUs for flows.
rps_dev_flow_table is specific to each device queue. Each entry
contains a CPU and a tail queue counter. The CPU is the "current"
CPU for a matching flow. The tail queue counter holds the value
of a tail queue counter for the associated CPU's backlog queue at
the time of last enqueue for a flow matching the entry.
Each backlog queue has a queue head counter which is incremented
on dequeue, and so a queue tail counter is computed as queue head
count + queue length. When a packet is enqueued on a backlog queue,
the current value of the queue tail counter is saved in the hash
entry of the rps_dev_flow_table.
And now the trick: when selecting the CPU for RPS (get_rps_cpu)
the rps_sock_flow table and the rps_dev_flow table for the RX queue
are consulted. When the desired CPU for the flow (found in the
rps_sock_flow table) does not match the current CPU (found in the
rps_dev_flow table), the current CPU is changed to the desired CPU
if one of the following is true:
- The current CPU is unset (equal to RPS_NO_CPU)
- Current CPU is offline
- The current CPU's queue head counter >= queue tail counter in the
rps_dev_flow table. This checks if the queue tail has advanced
beyond the last packet that was enqueued using this table entry.
This guarantees that all packets queued using this entry have been
dequeued, thus preserving in order delivery.
Making each queue have its own rps_dev_flow table has two advantages:
1) the tail queue counters will be written on each receive, so
keeping the table local to interrupting CPU s good for locality. 2)
this allows lockless access to the table-- the CPU number and queue
tail counter need to be accessed together under mutual exclusion
from netif_receive_skb, we assume that this is only called from
device napi_poll which is non-reentrant.
This patch implements RFS for TCP and connected UDP sockets.
It should be usable for other flow oriented protocols.
There are two configuration parameters for RFS. The
"rps_flow_entries" kernel init parameter sets the number of
entries in the rps_sock_flow_table, the per rxqueue sysfs entry
"rps_flow_cnt" contains the number of entries in the rps_dev_flow
table for the rxqueue. Both are rounded to power of two.
The obvious benefit of RFS (over just RPS) is that it achieves
CPU locality between the receive processing for a flow and the
applications processing; this can result in increased performance
(higher pps, lower latency).
The benefits of RFS are dependent on cache hierarchy, application
load, and other factors. On simple benchmarks, we don't necessarily
see improvement and sometimes see degradation. However, for more
complex benchmarks and for applications where cache pressure is
much higher this technique seems to perform very well.
Below are some benchmark results which show the potential benfit of
this patch. The netperf test has 500 instances of netperf TCP_RR
test with 1 byte req. and resp. The RPC test is an request/response
test similar in structure to netperf RR test ith 100 threads on
each host, but does more work in userspace that netperf.
e1000e on 8 core Intel
No RFS or RPS 104K tps at 30% CPU
No RFS (best RPS config): 290K tps at 63% CPU
RFS 303K tps at 61% CPU
RPC test tps CPU% 50/90/99% usec latency Latency StdDev
No RFS/RPS 103K 48% 757/900/3185 4472.35
RPS only: 174K 73% 415/993/2468 491.66
RFS 223K 73% 379/651/1382 315.61
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_pick_tx() caches tx queue_index on a socket, we must check
socket dst_entry matches skb one, or risk a crash later, as reported by
Denys Fedorysychenko, if old packets are in flight during a route
change, involving devices with different number of queues.
Bug introduced by commit a4ee3ce3
(net: Use sk_tx_queue_mapping for connected sockets)
Reported-by: Denys Fedorysychenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris reported netif_rx() is calling smp_processor_id() from
preemptible context, in particular when caller is
ip_dev_loopback_xmit().
RPS commit added this smp_processor_id() call, this patch makes sure
preemption is disabled. rps_get_cpus() wants rcu_read_lock() anyway, we
can dot it a bit earlier.
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_bond_should_drop() is too big to be inlined.
This patch reduces kernel text size, and its compilation time as well
(shrinking include/linux/netdevice.h)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With latest CONFIG_PROVE_RCU stuff, I felt more comfortable to make this
work.
sk->sk_dst_cache is currently protected by a rwlock (sk_dst_lock)
This rwlock is readlocked for a very small amount of time, and dst
entries are already freed after RCU grace period. This calls for RCU
again :)
This patch converts sk_dst_lock to a spinlock, and use RCU for readers.
__sk_dst_get() is supposed to be called with rcu_read_lock() or if
socket locked by user, so use appropriate rcu_dereference_check()
condition (rcu_read_lock_held() || sock_owned_by_user(sk))
This patch avoids two atomic ops per tx packet on UDP connected sockets,
for example, and permits sk_dst_lock to be much less dirtied.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont use netdev_warn() in dev_cap_txqueue() and get_rps_cpu() so that we
can catch following warnings without crash.
bond0.2240 received packet on queue 6, but number of RX queues is 1
bond0.2240 received packet on queue 11, but number of RX queues is 1
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Changli Gao, we must call local_irq_enable() after
rps_unlock()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spin_unlock_irq which needs to be rps_unlock.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
+little renaming of unicast functions to be smooth with multicast ones
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup to commit 5acbbd428d
(net: change illegal_highdma to use dma_mask)
If dev->dev.parent is NULL, we should not try to dereference it.
Dont force inline illegal_highdma() as its pretty big now.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Hancock pointed out two problems about NETIF_F_HIGHDMA:
-Many drivers only set the flag when they detect they can use 64-bit DMA,
since otherwise they could receive DMA addresses that they can't handle
(which on platforms without IOMMU/SWIOTLB support is fatal). This means that if
64-bit support isn't available, even buffers located below 4GB will get copied
unnecessarily.
-Some drivers set the flag even though they can't actually handle 64-bit DMA,
which would mean that on platforms without IOMMU/SWIOTLB they would get a DMA
mapping error if the memory they received happened to be located above 4GB.
http://lkml.org/lkml/2010/3/3/530
We can use the dma_mask if we need bouncing or not here. Then we can
safely fix drivers that misuse NETIF_F_HIGHDMA.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
keep the old behavior on SMP without rps
RPS introduces a lock operation to per cpu variable input_pkt_queue on
SMP whenever rps is enabled or not. On SMP without RPS, this lock isn't
needed at all.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/core/dev.c | 42 ++++++++++++++++++++++++++++--------------
1 file changed, 28 insertions(+), 14 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
RPS currently depends on SMP and SYSFS
Adding a CONFIG_RPS makes sense in case this requirement changes in the
future. This patch saves about 1500 bytes of kernel text in case SMP is
on but SYSFS is off.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to take spinlocks when dequeuing from input_pkt_queue in flush_backlog.
Also, flush_backlog can now be called directly from netdev_run_todo.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU to avoid RTNL use in dev_getfirstbyhwtype()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently force a synchronize_net() in netdev_set_master()
This seems necessary only when a slave had a master and we dismantle it.
In the other case ("ifenslave bond0 ethO"), we dont need this long
delay.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the type change, addresses in unicast and multicast lists wouldn't make
sense, not to mention possible different lenghts. So flush both lists here.
Note "dev_addr_discard" will be very soon replaced by "dev_mc_flush" (once
mc_list conversion will be done).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing "ifenslave -d bond0 eth0", there is chance to get NULL
dereference in netif_receive_skb(), because dev->master suddenly becomes
NULL after we tested it.
We should use ACCESS_ONCE() to avoid this (or rcu_dereference())
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the possibility to refuse the bonding type change for
other subsystems (such as for example bridge, vlan, etc.)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements software receive side packet steering (RPS). RPS
distributes the load of received packet processing across multiple CPUs.
Problem statement: Protocol processing done in the NAPI context for received
packets is serialized per device queue and becomes a bottleneck under high
packet load. This substantially limits pps that can be achieved on a single
queue NIC and provides no scaling with multiple cores.
This solution queues packets early on in the receive path on the backlog queues
of other CPUs. This allows protocol processing (e.g. IP and TCP) to be
performed on packets in parallel. For each device (or each receive queue in
a multi-queue device) a mask of CPUs is set to indicate the CPUs that can
process packets. A CPU is selected on a per packet basis by hashing contents
of the packet header (e.g. the TCP or UDP 4-tuple) and using the result to index
into the CPU mask. The IPI mechanism is used to raise networking receive
softirqs between CPUs. This effectively emulates in software what a multi-queue
NIC can provide, but is generic requiring no device support.
Many devices now provide a hash over the 4-tuple on a per packet basis
(e.g. the Toeplitz hash). This patch allow drivers to set the HW reported hash
in an skb field, and that value in turn is used to index into the RPS maps.
Using the HW generated hash can avoid cache misses on the packet when
steering it to a remote CPU.
The CPU mask is set on a per device and per queue basis in the sysfs variable
/sys/class/net/<device>/queues/rx-<n>/rps_cpus. This is a set of canonical
bit maps for receive queues in the device (numbered by <n>). If a device
does not support multi-queue, a single variable is used for the device (rx-0).
Generally, we have found this technique increases pps capabilities of a single
queue device with good CPU utilization. Optimal settings for the CPU mask
seem to depend on architectures and cache hierarcy. Below are some results
running 500 instances of netperf TCP_RR test with 1 byte req. and resp.
Results show cumulative transaction rate and system CPU utilization.
e1000e on 8 core Intel
Without RPS: 108K tps at 33% CPU
With RPS: 311K tps at 64% CPU
forcedeth on 16 core AMD
Without RPS: 156K tps at 15% CPU
With RPS: 404K tps at 49% CPU
bnx2x on 16 core AMD
Without RPS 567K tps at 61% CPU (4 HW RX queues)
Without RPS 738K tps at 96% CPU (8 HW RX queues)
With RPS: 854K tps at 76% CPU (4 HW RX queues)
Caveats:
- The benefits of this patch are dependent on architecture and cache hierarchy.
Tuning the masks to get best performance is probably necessary.
- This patch adds overhead in the path for processing a single packet. In
a lightly loaded server this overhead may eliminate the advantages of
increased parallelism, and possibly cause some relative performance degradation.
We have found that masks that are cache aware (share same caches with
the interrupting CPU) mitigate much of this.
- The RPS masks can be changed dynamically, however whenever the mask is changed
this introduces the possibility of generating out of order packets. It's
probably best not change the masks too frequently.
Signed-off-by: Tom Herbert <therbert@google.com>
include/linux/netdevice.h | 32 ++++-
include/linux/skbuff.h | 3 +
net/core/dev.c | 335 +++++++++++++++++++++++++++++++++++++--------
net/core/net-sysfs.c | 225 ++++++++++++++++++++++++++++++-
net/core/skbuff.c | 2 +
5 files changed, 538 insertions(+), 59 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split dev_change_flags() into two functions: __dev_change_flags() to
perform the actual changes and __dev_notify_flags() to invoke netdevice
notifiers. This will be used by rtnl_link to defer netlink notifications
until the device has been fully configured.
This changes ordering of some operations, in particular:
- netlink notifications are sent after all changes have been performed.
As a side effect this surpresses one unnecessary netlink message when
the IFF_UP and other flags are changed simultaneously.
- The NETDEV_UP/NETDEV_DOWN and NETDEV_CHANGE notifiers are invoked
after all changes have been performed. Their relative is unchanged.
- net_dmaengine_put() is invoked before the NETDEV_DOWN notifier instead
of afterwards. This should not make any difference since both RX and TX
are already shut down at this point.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support specifying device flags during device creation,
we must be able to roll back device registration in case setting the
flags fails without sending any notifications related to the device
to userspace.
This patch changes rollback_registered_many() and register_netdevice()
to manually send netlink notifications for devices not handled by
rtnl_link and allows to defer notifications for devices handled by
rtnl_link until setup is complete.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_first_entry macro; no longer any need to use
'next' directly in list to find first entry.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update rcu_dereference() primitives to use new lockdep-based
checking. The rcu_dereference() in __in6_dev_get() may be
protected either by rcu_read_lock() or RTNL, per Eric Dumazet.
The rcu_dereference() in __sk_free() is protected by the fact
that it is never reached if an update could change it. Check
for this by using rcu_dereference_check() to verify that the
struct sock's ->sk_wmem_alloc counter is zero.
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <1266887105-1528-5-git-send-email-paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.
I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.
I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset enables the ethtool layer to program n-tuple
filters to an underlying device. The idea is to allow capable
hardware to have static rules applied that can assist steering
flows into appropriate queues.
Hardware that is known to support these types of filters today
are ixgbe and niu.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vlan and macvlan drivers, the start_xmit function forwards
data to the dev_queue_xmit function for another device, which may
potentially belong to a different namespace.
To make sure that classification stays within a single namespace,
this resets the potentially critical fields.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces three macros to work with uc list from net drivers.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid checking twice whether skb needs to be linearized, if one
skb_linearize was already done.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The contents of /proc/net/dev is annoying to parse, because
it changes whether there is a space after the "ethX:" or not.
It depends upon the size of the "Receive bytes" counter,
if the number is below 7 digits, then there is whitespaces
else if the number is 8 digits or above there is no space
between the ":" and the number.
This patch changes the output to assure there is always a space
between the ":" and the number. Given that all existing userspace
application already need to handle the whitespaces, I see
no breakage of existing tools.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Wed, Jan 06, 2010 at 10:10:03PM +0100, Eric Dumazet wrote:
> Le 06/01/2010 19:38, Eric Dumazet a écrit :
> >
> > (net-next-2.6 doesnt work well on my bond/vlan setup, I suspect I need a bisection)
>
> David, I had to revert 1f3c8804ac
> (bonding: allow arp_ip_targets on separate vlans to use arp validation)
>
> Or else, my vlan devices dont work (unfortunatly I dont have much time
> these days to debug the thing)
>
> My config :
>
> +---------+
> vlan.103 -----+ bond0 +--- eth1 (bnx2)
> | +
> vlan.825 -----+ +--- eth2 (tg3)
> +---------+
>
> $ cat /proc/net/bonding/bond0
> Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
>
> Bonding Mode: fault-tolerance (active-backup)
> Primary Slave: None
> Currently Active Slave: eth2
> MII Status: up
> MII Polling Interval (ms): 100
> Up Delay (ms): 0
> Down Delay (ms): 0
>
> Slave Interface: eth1 (bnx2)
> MII Status: down
> Link Failure Count: 1
> Permanent HW addr: 00:1e:0b:ec:d3:d2
>
> Slave Interface: eth2 (tg3)
> MII Status: up
> Link Failure Count: 0
> Permanent HW addr: 00:1e:0b:92:78:50
>
This patch fixes up a problem with found with commit
1f3c8804ac. The original change
overloaded null_or_orig, but doing that prevented any packet handlers
that were not tied to a specific device (i.e. ptype->dev == NULL) from
ever receiving any frames.
The null_or_orig variable cannot be overloaded, and must be kept as NULL
to prevent the frame from being ignored by packet handlers designed to
accept frames on any interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
