* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
This is the new FW HSI blob and the relevant definitions without logic changes.
It also included code adaptation for new HSI. New features are not enabled.
New FW/HSI includes:
- Support for 57712 HW
- Future support for VF (not used)
- Improvements in FW interrupts scheme
- FW FCoE hooks (stubs for future usage)
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC3720, nopout packet sent in response to unsolicited
nopin packet requesting a response must retain the TTT of the requester.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In compliance to RFC793, a TCP graceful termination will be used
instead of an abortive termination for the case where the remote
has initiated the close of the connection.
Additionally, a TCP abortive termination will be used to close the
connection when a logout response is not received in time after a
logout request has been initiated.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added variables to separate the fine tuned timeout values for
connection destroy and context destroy for both 1g and 10g devices.
v2: Extended the 5771X disconnect timeout from 10s to 20s as the firmware
has a retransmission timeout of 16s. This fixes one of the iscsi_endpoint
leak issues when the target is slow or non-responsive to our TCP FIN.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For cases where the iSCSI disconnection procedure times out due to
the iSCSI daemon being slow or unresponsive, the bnx2i_stop routine
will now perform hardware cleanup via bnx2i_hw_ep_disconnect on all
active endpoints so that subsequent operations will perform properly.
Also moved the mutex locks inside ep_connect and ep_disconnect so
that proper exclusivity can resolve simultaneous calls to the
ep_disconnect routine.
v2: Removed the unnecessary read lock in the bnx2i_stop
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This introduces a new active linklist which would link up all active
bnx2i_endpoints. This will be used by subsequent patches that
follows.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bnx2i driver has to wait and cleanup all iscsi endpoints before
returning from bnx2i_stop(). This is to make sure all chip resources
are freed before chip is reset.
As the requirements for 1G and 10G chipsets is different, added
per-device 'hba_shutdown_tmo' parameter to adapter structure
If the connections are not torn down by the daemon within this timeout
period, 'cid's will be leaked in 10G device. 1G devices are more
flexible and do not leak any resources because the whole chip ports
gets reset when MTU is changed or ethtool selftest is run
fixed a minor issue in bnx2i_ep_poll() which unnecessarily forced
error return code when driver timed out waiting for TCP connect
request to complete
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Only affects 5771x (10G chipsets) devices
This is an optimized CQ arming algoritm which takes into account the
number of outstanding tasks
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This just has bnx2i use the iscsi_suspend_queue helper.
The suspend works as follows:
When ep_poll has succeeed iscsid will call conn_bind, the LLD will
then call iscsi_conn_bind which will clear the suspend bit.
When ep_disconnect is called (or if there is a conn error) we set
the suspend bit. For the ep_disconnect case I added a helper
in the previous kernel that will take the session lock to make sure
iscsi_queuecommand/xmit_task is not running and it will set
the suspend bit.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
5706/5708/5709 devices allow driver/user to set page size. By default it is
set to 4096. Current drivers do not program this register based on
architecture type (e.g. x86 = 4K, IA64 = 16K) and by choice lets device use
the defaults. So while mapping connection context memory (doorebll registers),
driver has to match page size used by the device. Included change fixes the
issue we uncovered during IA64 testing
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
New iSCSI driver for Broadcom BNX2 devices. The driver interfaces with
the CNIC driver to access the hardware.
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
