* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
this patch gives the possibility to workaround bug ENGcm09152
on i.MX35 when the hardware workaround is also implemented on
the board.
It covers the workaround described on page 25 of the following Errata :
http://cache.freescale.com/files/dsp/doc/errata/IMX35CE.pdf
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It has USB phy built inside the IP itself.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts arm to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- ARM defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds support for termiox
Reviewed-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
x86-64: Only set max_pfn_mapped to 512 MiB if we enter via head_64.S
xen: Cope with unmapped pages when initializing kernel pagetable
memblock, bootmem: Round pfn properly for memory and reserved regions
memblock: Annotate memblock functions with __init_memblock
memblock: Allow memblock_init to be called early
memblock/arm: Fix memblock_region_is_memory() typo
x86, memblock: Remove __memblock_x86_find_in_range_size()
memblock: Fix wraparound in find_region()
x86-32, memblock: Make add_highpages honor early reserved ranges
x86, memblock: Fix crashkernel allocation
arm, memblock: Fix the sparsemem build
memblock: Fix section mismatch warnings
powerpc, memblock: Fix memblock API change fallout
memblock, microblaze: Fix memblock API change fallout
x86: Remove old bootmem code
x86, memblock: Use memblock_memory_size()/memblock_free_memory_size() to get correct dma_reserve
x86: Remove not used early_res code
x86, memblock: Replace e820_/_early string with memblock_
x86: Use memblock to replace early_res
x86, memblock: Use memblock_debug to control debug message print out
...
Fix up trivial conflicts in arch/x86/kernel/setup.c and kernel/Makefile
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
spi/bfin_spi: namespace local structs
spi/bfin_spi: init early
spi/bfin_spi: check per-transfer bits_per_word
spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
spi/bfin_spi: cs should be always low when a new transfer begins
spi/bfin_spi: fix typo in comment
spi/bfin_spi: reject unsupported SPI modes
spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
spi/bfin_spi: combine duplicate SPI_CTL read/write logic
spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
spi/bfin_spi: push all size checks into the transfer function
spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
spi/bfin_spi: sync hardware state before reprogramming everything
spi/bfin_spi: save/restore state when suspending/resuming
spi/bfin_spi: redo GPIO CS handling
Blackfin: SPI: expand SPI bitmasks
spi/bfin_spi: use the SPI namespaced bit names
spi/bfin_spi: drop extra memory we don't need
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Since we can get both physical and virtual addresses from the addruart
macro, we can use this to establish the debug mappings.
In the case of CONFIG_DEBUG_ICEDCC, we don't need any mappings, but
may still need to setup r7 correctly.
Incorporating ASM changes from Nicolas Pitre <npitre@fluxnic.net>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
As mentioned in the comment right at the top, the first four fields
are directly accessed by assembly code in head.S. Move nr_irqs so the
comment is true again.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
without this patch we get :
arch/arm/mach-imx/built-in.o: In function `eukrea_cpuimx27_init':
eukrea_mbimx27-baseboard.c:(.init.text+0x44c): undefined reference to `mxc_ulpi_access_ops'
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
this patch fix the following errors :
arch/arm/mach-mx3/mach-pcm037_eet.c:62: error: implicit declaration of function 'MXC_SPI_CS'
arch/arm/mach-mx3/mach-pcm037_eet.c:185: error: implicit declaration of function 'imx35_add_spi_imx0'
from the Kconfig pcm037 is i.MX31 based and not i.MX35 so replace
imx35_add_spi_imx0 by imx31_add_spi_imx0
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: remove unneeded #include <mach/spi.h>]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is only a partial revert of "ARM: mx3/mx31ads: fold board
header in its only user"
[commit ccfa7c2698)]
As some of the the board defines are also used in the cs89x0
ethernet driver by the i.MX31 ADS.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the attached patch allows SD to work on i.MX51 with Wolfram's drivers
Tested on i.MX51.
Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Without this exiting WFI can result in cache corruption.
Code taken from Freescale's 2.6.27 BSP and tested on i.MX35
Signed-off-by: Eric Bénard <eric@eukrea.com>
this patch fix the following errors :
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_SDMA_BASE_ADDR’ undeclared here (not in a function)
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_INT_SDMA’ undeclared here (not in a function)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID
* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: Eric Bénard <eric@eukrea.com>
During the reorganisation of the imx-i2c devices
(in 64de5ec168) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.
Applies on 2.6.36-rc7
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes build error about GPIO address due to
conflict of commit 4d914705 and 19a2c065.
- commit 4d914705: Fix on GPIO base addresses
- commit 19a2c065: Moves initial map for merging S5P64X0
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ various fixes ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1287036094.7768.291.camel@yhuang-dev>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
