This reverts commit 7a249cf83d.
That commit created a situation that could lead to a filesystem
hang. As Dave Chinner pointed out, xfs_trans_alloc() could hold a
reference to m_active_trans (i.e., keep it non-zero) and then wait
for SB_FREEZE_TRANS to complete. Meanwhile a filesystem freeze
request could set SB_FREEZE_TRANS and then wait for m_active_trans
to drop to zero. Nobody benefits from this sequence of events...
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Remove two variables that serve no purpose in
xfs_alloc_ag_vextent_exact().
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Pavol pointed out that there is one silent error case in the mount
path, and that others are rather uninformative.
I've taken Pavol's suggested patch and extended it a bit to also:
* fix a message which says "turned off" but actually errors out
* consolidate the vaguely differentiated "SB sanity check [12]"
messages, and hexdump the superblock for analysis
Original-patch-by: Pavol Gono <Pavol.Gono@siemens.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
There is no need for a pre-flush when doing writing the second part of a
split log buffer, and if we are using an external log there is no need
to do a full cache flush of the log device at all given that all writes
to it use the FUA flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Remove the unused and misnamed _XBF_RUN_QUEUES flag, rename XBF_LOG_BUFFER
to the more fitting XBF_SYNCIO, and split XBF_ORDERED into XBF_FUA and
XBF_FLUSH to allow more fine grained control over the bio flags. Also
cleanup processing of the flags in _xfs_buf_ioapply to make more sense,
and renumber the sparse flag number space to group flags by purpose.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
All other xfs_buf_get/read-like helpers return the buffer locked, make sure
xfs_buf_get_uncached isn't different for no reason. Half of the callers
already lock it directly after, and the others probably should also keep
it locked if only for consistency and beeing able to use xfs_buf_rele,
but I'll leave that for later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Rename xfs_buf_cond_lock and reverse it's return value to fit most other
trylock operations in the Kernel and XFS (with the exception of down_trylock,
after which xfs_buf_cond_lock was modelled), and replace xfs_buf_lock_val
with an xfs_buf_islocked for use in asserts, or and opencoded variant in
tracing. remove the XFS_BUF_* wrappers for all the locking helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Micro-optimize various comparisms by always byteswapping the constant
instead of the variable, which allows to do the swap at compile instead
of runtime.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Switch the shortform directory code over to use the generic
get_unaligned_beXX helpers instead of reinventing them. As a result
kill off xfs_arch.h and move the setting of XFS_NATIVE_HOST into
xfs_linux.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Simplify the confusing xfs_dir2_leaf structure. It is supposed to describe
an XFS dir2 leaf format btree block, but due to the variable sized nature
of almost all elements in it it can't actuall do anything close to that
job. Remove the members that are after the first variable sized array,
given that they could only be used for sizeof expressions that can as well
just use the underlying types directly, and make the ents array a real
C99 variable sized array.
Also factor out the xfs_dir2_leaf_size, to make the sizing of a leaf
entry which already was convoluted somewhat readable after using the
longer type names in the sizeof expressions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Remove the tag member which is at a variable offset after the actual
name, and make name a real variable sized C99 array instead of the incorrect
one-sized array which confuses (not only) gcc.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Remove the confusing xfs_dir2_data structure. It is supposed to describe
an XFS dir2 data btree block, but due to the variable sized nature of
almost all elements in it it can't actuall do anything close to that
job. In addition to accessing the fixed offset header structure it was
only used to get a pointer to the first dir or unused entry after it,
which can be trivially replaced by pointer arithmetics on the header
pointer. For most users that is actually more natural anyway, as they
don't use a typed pointer but rather a character pointer for further
arithmetics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
In most places we can simply pass around and use the struct xfs_dir2_data_hdr,
which is the first and most important member of struct xfs_dir2_data instead
of the full structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Remove the confusing xfs_dir2_block structure. It is supposed to describe
an XFS dir2 block format btree block, but due to the variable sized nature
of almost all elements in it it can't actuall do anything close to that
job. In addition to accessing the fixed offset header structure it was
only used to get a pointer to the first dir or unused entry after it,
which can be trivially replaced by pointer arithmetics on the header
pointer. For most users that is actually more natural anyway, as they
don't use a typed pointer but rather a character pointer for further
arithmetics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
In most places we can simply pass around and use the struct xfs_dir2_data_hdr,
which is the first and most important member of struct xfs_dir2_block instead
of the full structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Remove the inumber member which is at a variable offset after the actual
name, and make name a real variable sized C99 array instead of the incorrect
one-sized array which confuses (not only) gcc. Based on this clean up
the helpers to calculate the entry size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
The list field of it is never cactually used, so all uses can simply be
replaced with the xfs_dir2_sf_hdr_t type that it has as first member.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Refactor the shortform directory helpers that deal with the 32-bit vs
64-bit wide inode numbers into more sensible helpers, and kill the
xfs_intino_t typedef that is now superflous.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Add a new xfs_dir2_leaf_find_entry helper to factor out some duplicate code
from xfs_dir2_leaf_addname xfs_dir2_leafn_add. Found by Eric Sandeen using
an automated code duplication checker.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Remove the transaction pointer in the inode. It's only used to avoid
passing down an argument in the bmap code, and for a few asserts in
the transaction code right now.
Also use the local variable ip in a few more places in xfs_inode_item_unlock,
so that it isn't only used for debug builds after the above change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
As pointed out by Jan xfs_trans_alloc can race with a concurrent filesystem
freeze when it sleeps during the memory allocation. Fix this by moving the
wait_for_freeze call after the memory allocation. This means moving the
freeze into the low-level _xfs_trans_alloc helper, which thus grows a new
argument. Also fix up some comments in that area while at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <david@fromorbit.com>
The following script from Wu Fengguang shows very bad behaviour in XFS
when aggressively dirtying data during a sync on XFS, with sync times
up to almost 10 times as long as ext4.
A large part of the issue is that XFS writes data out itself two times
in the ->sync_fs method, overriding the livelock protection in the core
writeback code, and another issue is the lock-less xfs_ioend_wait call,
which doesn't prevent new ioend from being queue up while waiting for
the count to reach zero.
This patch removes the XFS-internal sync calls and relies on the VFS
to do it's work just like all other filesystems do. Note that the
i_iocount wait which is rather suboptimal is simply removed here.
We already do it in ->write_inode, which keeps the current supoptimal
behaviour. We'll eventually need to remove that as well, but that's
material for a separate commit.
------------------------------ snip ------------------------------
#!/bin/sh
umount /dev/sda7
mkfs.xfs -f /dev/sda7
# mkfs.ext4 /dev/sda7
# mkfs.btrfs /dev/sda7
mount /dev/sda7 /fs
echo $((50<<20)) > /proc/sys/vm/dirty_bytes
pid=
for i in `seq 10`
do
dd if=/dev/zero of=/fs/zero-$i bs=1M count=1000 &
pid="$pid $!"
done
sleep 1
tic=$(date +'%s')
sync
tac=$(date +'%s')
echo
echo sync time: $((tac-tic))
egrep '(Dirty|Writeback|NFS_Unstable)' /proc/meminfo
pidof dd > /dev/null && { kill -9 $pid; echo sync NOT livelocked; }
------------------------------ snip ------------------------------
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Split the guts of xfs_itruncate_finish that loop over the existing extents
and calls xfs_bunmapi on them into a new helper, xfs_itruncate_externs.
Make xfs_attr_inactive call it directly instead of xfs_itruncate_finish,
which allows to simplify the latter a lot, by only letting it deal with
the data fork. As a result xfs_itruncate_finish is renamed to
xfs_itruncate_data to make its use case more obvious.
Also remove the sync parameter from xfs_itruncate_data, which has been
unessecary since the introduction of the busy extent list in 2002, and
completely dead code since 2003 when the XFS_BMAPI_ASYNC parameter was
made a no-op.
I can't actually see why the xfs_attr_inactive needs to set the transaction
sync, but let's keep this patch simple and without changes in behaviour.
Also avoid passing a useless argument to xfs_isize_check, and make it
private to xfs_inode.c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
xfs_itruncate_start is a rather length wrapper that evaluates to a call
to xfs_ioend_wait and xfs_tosspages, and only has two callers.
Instead of using the complicated checks left over from IRIX where we
can to truncate the pagecache just call xfs_tosspages
(aka truncate_inode_pages) directly as we want to get rid of all data
after i_size, and truncate_inode_pages handles incorrect alignments
and too large offsets just fine.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Get rid of the special case where we use unlogged timestamp updates for
a truncate to the current inode size, and just call xfs_setattr_nonsize
for it to treat it like a utimes calls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Split up xfs_setattr into two functions, one for the complex truncate
handling, and one for the trivial attribute updates. Also move both
new routines to xfs_iops.c as they are fairly Linux-specific.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
GCC 4.6 complains about an array subscript is above array bounds when
using the btree index to index into the agf_levels array. The only
two indices passed in are 0 and 1, and we have an assert insuring that.
Replace the trick of using the array index directly with using constants
in the already existing branch for assigning the XFS_BTREE_LASTREC_UPDATE
flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
The non-blockig behaviour in xfs_vm_writepage currently is conditional on
having both the WB_SYNC_NONE sync_mode and the nonblocking flag set.
The latter used to be used by both pdflush, kswapd and a few other places
in older kernels, but has been fading out starting with the introduction
of the per-bdi flusher threads.
Enable the non-blocking behaviour for all WB_SYNC_NONE calls to get back
the behaviour we want.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Now that we reject direct reclaim in addition to always using GFP_NOFS
allocation there's no chance we'll ever end up in ->writepage with
PF_FSTRANS set. Add a WARN_ON if we hit this case, and stop checking
if we'd actually need to start a transaction.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
When inodes are marked stale in a transaction, they are treated
specially when the inode log item is being inserted into the AIL.
It tries to avoid moving the log item forward in the AIL due to a
race condition with the writing the underlying buffer back to disk.
The was "fixed" in commit de25c18 ("xfs: avoid moving stale inodes
in the AIL").
To avoid moving the item forward, we return a LSN smaller than the
commit_lsn of the completing transaction, thereby trying to trick
the commit code into not moving the inode forward at all. I'm not
sure this ever worked as intended - it assumes the inode is already
in the AIL, but I don't think the returned LSN would have been small
enough to prevent moving the inode. It appears that the reason it
worked is that the lower LSN of the inodes meant they were inserted
into the AIL and flushed before the inode buffer (which was moved to
the commit_lsn of the transaction).
The big problem is that with delayed logging, the returning of the
different LSN means insertion takes the slow, non-bulk path. Worse
yet is that insertion is to a position -before- the commit_lsn so it
is doing a AIL traversal on every insertion, and has to walk over
all the items that have already been inserted into the AIL. It's
expensive.
To compound the matter further, with delayed logging inodes are
likely to go from clean to stale in a single checkpoint, which means
they aren't even in the AIL at all when we come across them at AIL
insertion time. Hence these were all getting inserted into the AIL
when they simply do not need to be as inodes marked XFS_ISTALE are
never written back.
Transactional/recovery integrity is maintained in this case by the
other items in the unlink transaction that were modified (e.g. the
AGI btree blocks) and committed in the same checkpoint.
So to fix this, simply unpin the stale inodes directly in
xfs_inode_item_committed() and return -1 to indicate that the AIL
insertion code does not need to do any further processing of these
inodes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
If the attribute fork on an inode is in btree format and has
multiple levels (i.e node format rather than leaf format), then a
lookup failure will trigger an assert failure in xfs_da_path_shift
if the flag XFS_DA_OP_OKNOENT is not set. This flag is used to
indicate to the directory btree code that not finding an entry is
not a fatal error. In the case of doing a lookup for a directory
name removal, this is valid as a user cannot insert an arbitrary
name to remove from the directory btree.
However, in the case of the attribute tree, a user has direct
control over the attribute name and can ask for any random name to
be removed without any validation. In this case, fsstress is asking
for a non-existent user.selinux attribute to be removed, and that is
causing xfs_da_path_shift() to fall off the bottom of the tree where
it asserts that a lookup failure is allowed. Because the flag is not
set, we die a horrible death on a debug enable kernel.
Prevent this assert from firing on attribute removes by adding the
op_flag XFS_DA_OP_OKNOENT to atribute removal operations.
Discovered when testing on a SELinux enabled system by fsstress in
test 070 by trying to remove a non-existent user.selinux attribute.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
When an inode is truncated down, speculative preallocation is
removed from the inode. This should also reset the state bits for
controlling whether preallocation is subsequently removed when the
file is next closed. The flag is not being cleared, so repeated
operations on a file that first involve a truncate (e.g. multiple
repeated dd invocations on a file) give different file layouts for
the second and subsequent invocations.
Fix this by clearing the XFS_IDIRTY_RELEASE state bit when the
XFS_ITRUNCATED bit is detected in xfs_release() and hence ensure
that speculative delalloc is removed on files that have been
truncated down.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
XFS inodes has several per-lifetime state fields that determine the
behaviour of the inode. These state fields are not all reset when an
inode is reused from the reclaimable state.
This can lead to unexpected behaviour of the new inode such as
speculative preallocation not being truncated away in the expected
manner for local files until the inode is subsequently truncated,
freed or cycles out of the cache. It can also lead to an inode being
considered to be a filestream inode or having been truncated when
that is not the case.
Rework the reinitialisation of the inode when it is recycled to
ensure that it is pristine before it is reused. While there, also
fix the resetting of state flags in the recycling error paths so the
inode does not become unreclaimable.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
There's no reason not to support cache flushing on external log devices.
The only thing this really requires is flushing the data device first
both in fsync and log commits. A side effect is that we also have to
remove the barrier write test during mount, which has been superflous
since the new FLUSH+FUA code anyway. Also use the chance to flush the
RT subvolume write cache before the fsync commit, which is required
for correct semantics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
->mknod() should return negative on errors and PTR_ERR() gives
already negative value...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Tell the filesystem if we just updated timestamp (I_DIRTY_SYNC) or
anything else, so that the filesystem can track internally if it
needs to push out a transaction for fdatasync or not.
This is just the prototype change with no user for it yet. I plan
to push large XFS changes for the next merge window, and getting
this trivial infrastructure in this window would help a lot to avoid
tree interdependencies.
Also remove incorrect comments that ->dirty_inode can't block. That
has been changed a long time ago, and many implementations rely on it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: correctly decrement the extent buffer index in xfs_bmap_del_extent
xfs: check for valid indices in xfs_iext_get_ext and xfs_iext_idx_to_irec
xfs: fix up asserts in xfs_iflush_fork
xfs: do not do pointer arithmetic on extent records
xfs: do not use unchecked extent indices in xfs_bunmapi
xfs: do not use unchecked extent indices in xfs_bmapi
xfs: do not use unchecked extent indices in xfs_bmap_add_extent_*
xfs: remove if_lastex
xfs: remove the unused XFS_BMAPI_RSVBLOCKS flag
xfs: do not discard alloc btree blocks
xfs: add online discard support
The code in xfs_bmap_del_extent does not correctly decrement the
extent buffer index when deleting a whole extent. Most of the time
this gets caught by checks in xfs_bmapi that work around it and
decrement it manually and thus wasn't noticed so far.
Based on an earlier patch from Lachlan McIlroy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Based on an earlier patch from Lachlan McIlroy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Remove asserts in xfs_iflush_fork that would call xfs_iext_get_ext
with a potentially invalid extent buffer index.
Based on an earlier patch from Lachlan McIlroy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
We need to call xfs_iext_get_ext for the previous extent to get a
valid pointer, and can't just do pointer arithmetics as they might
be in different pages.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Make sure to only call xfs_iext_get_ext after we've validate the
extent index when moving on to the next index in xfs_bunmapi. Also
remove the old workaround for too large indices that has been
superceeded by the proper fix in xfs_bmap_del_extent.
Based on an earlier patch from Lachlan McIlroy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Make sure to only call xfs_iext_get_ext after we've validate the
extent index when moving on to the next index in xfs_bmapi.
Based on an earlier patch from Lachlan McIlroy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Make sure to only call xfs_iext_get_ext after we've validate the
extent index in the various xfs_bmap_add_extent_* helpers.
Based on an earlier patch from Lachlan McIlroy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The if_lastex field in struct xfs_ifork is only used as a temporary
index during xfs_bmapi and xfs_bunmapi. Instead of using the inode
fork to store it keep it local in the callchain. Fortunately this
is very easy as we already pass a stack copy of it down the whole
chain which can simplify be changed to be passed by reference.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
The XFS_BMAPI_RSVBLOCKS is unused, and as far as I can see has
always been. Remove it to simplify the bmapi implementation and
conserve stack space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Change each shrinker's API by consolidating the existing parameters into
shrink_control struct. This will simplify any further features added w/o
touching each file of shrinker.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix warning]
[kosaki.motohiro@jp.fujitsu.com: fix up new shrinker API]
[akpm@linux-foundation.org: fix xfs warning]
[akpm@linux-foundation.org: update gfs2]
Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blocks for the allocation btree are allocated from and released to
the AGFL, and thus frequently reused. Even worse we do not have an
easy way to avoid using an AGFL block when it is discarded due to
the simple FILO list of free blocks, and thus can frequently stall
on blocks that are currently undergoing a discard.
Add a flag to the busy extent tracking structure to skip the discard
for allocation btree blocks. In normal operation these blocks are
reused frequently enough that there is no need to discard them
anyway, but if they spill over to the allocation btree as part of a
balance we "leak" blocks that we would otherwise discard. We could
fix this by adding another flag and keeping these block in the
rbtree even after they aren't busy any more so that we could discard
them when they migrate out of the AGFL. Given that this would cause
significant overhead I don't think it's worthwile for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Now that we have reliably tracking of deleted extents in a
transaction we can easily implement "online" discard support
which calls blkdev_issue_discard once a transaction commits.
The actual discard is a two stage operation as we first have
to mark the busy extent as not available for reuse before we
can start the actual discard. Note that we don't bother
supporting discard for the non-delaylog mode.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: obey minleft values during extent allocation correctly
xfs: reset buffer pointers before freeing them
xfs: avoid getting stuck during async inode flushes
xfs: fix xfs_itruncate_start tracing
xfs: fix duplicate workqueue initialisation
xfs: kill off xfs_printk()
xfs: fix race condition in AIL push trigger
xfs: make AIL target updates and compares 32bit safe.
xfs: always push the AIL to the target
xfs: exit AIL push work correctly when AIL is empty
xfs: ensure reclaim cursor is reset correctly at end of AG
xfs: add an x86 compat handler for XFS_IOC_ZERO_RANGE
xfs: fix compiler warning in xfs_trace.h
xfs: cleanup duplicate initializations
xfs: reduce the number of pagb_lock roundtrips in xfs_alloc_clear_busy
xfs: exact busy extent tracking
xfs: do not immediately reuse busy extent ranges
xfs: optimize AGFL refills
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
When allocating an extent that is long enough to consume the
remaining free space in an AG, we need to ensure that the allocation
leaves enough space in the AG for any subsequent bmap btree blocks
that are needed to track the new extent. These have to be allocated
in the same AG as we only reserve enough blocks in an allocation
transaction for modification of the freespace trees in a single AG.
xfs_alloc_fix_minleft() has been considering blocks on the AGFL as
free blocks available for extent and bmbt block allocation, which is
not correct - blocks on the AGFL are there exclusively for the use
of the free space btrees. As a result, when minleft is less than the
number of blocks on the AGFL, xfs_alloc_fix_minleft() does not trim
the given extent to leave minleft blocks available for bmbt
allocation, and hence we can fail allocation during bmbt record
insertion.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
When we free a vmapped buffer, we need to ensure the vmap address
and length we free is the same as when it was allocated. In various
places in the log code we change the memory the buffer is pointing
to before issuing IO, but we never reset the buffer to point back to
it's original memory (or no memory, if that is the case for the
buffer).
As a result, when we free the buffer it points to memory that is
owned by something else and attempts to unmap and free it. Because
the range does not match any known mapped range, it can trigger
BUG_ON() traps in the vmap code, and potentially corrupt the vmap
area tracking.
Fix this by always resetting these buffers to their original state
before freeing them.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
When the underlying inode buffer is locked and xfs_sync_inode_attr()
is doing a non-blocking flush, xfs_iflush() can return EAGAIN. When
this happens, clear the error rather than returning it to
xfs_inode_ag_walk(), as returning EAGAIN will result in the AG walk
delaying for a short while and trying again. This can result in
background walks getting stuck on the one AG until inode buffer is
unlocked by some other means.
This behaviour was noticed when analysing event traces followed by
code inspection and verification of the fix via further traces.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Variables are ordered incorrectly in trace call.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
The workqueue initialisation function is called twice when
initialising the XFS subsystem. Remove the second initialisation
call.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
xfs_alert_tag() can be defined using xfs_alert(), and thereby avoid
using xfs_printk() altogether. This is the only remaining use of
xfs_printk(), so changing it this way means xfs_printk() can simply
be eliminated.can simply be eliminated.can simply be eliminated.can
simply be eliminated.can simply be eliminated.can simply be
eliminated.can simply be eliminated.can simply be eliminated.can
simply be eliminated.
Also add format checking to the non-debug inline function xfs_debug.
Miscellaneous function prototype argument alignment.
(Updated to delete the definition of xfs_printk(), which is
no longer used or needed.)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. One is caused by a
race condition in determining whether there is a psh in progress or
not.
The XFS_AIL_PUSHING_BIT is used to determine whether a push is
currently in progress. When the AIL push work completes, it checked
whether the target changed and cleared the PUSHING bit to allow a
new push to be requeued. The race condition is as follows:
Thread 1 push work
smp_wmb()
smp_rmb()
check ailp->xa_target unchanged
update ailp->xa_target
test/set PUSHING bit
does not queue
clear PUSHING bit
does not requeue
Now that the push target is updated, new attempts to push the AIL
will not trigger as the push target will be the same, and hence
despite trying to push the AIL we won't ever wake it again.
The fix is to ensure that the AIL push work clears the PUSHING bit
before it checks if the target is unchanged.
As a result, both push triggers operate on the same test/set bit
criteria, so even if we race in the push work and miss the target
update, the thread requesting the push will still set the PUSHING
bit and queue the push work to occur. For safety sake, the same
queue check is done if the push work detects the target change,
though only one of the two will will queue new work due to the use
of test_and_set_bit() checks.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit e4d3c4a43b)
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. One of the problems
noticed was that updates of the push target are not 32 bit safe as
the target is a 64 bit value.
We cannot copy a 64 bit LSN without the possibility of corrupting
the result when racing with another updating thread. We have
function to do this update safely without needing to care about
32/64 bit issues - xfs_trans_ail_copy_lsn() - so use that when
updating the AIL push target.
Also move the reading of the target in the push work inside the AIL
lock, and use XFS_LSN_CMP() for the unlocked comparison during work
termination to close read holes as well.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit fd5670f22f)
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. One of the problems
discovered is a target mismatch between the item pushing loop and
the target itself.
The push trigger checks for the target increasing (i.e. new target >
current) while the push loop only pushes items that have a LSN <
current. As a result, we can get the situation where the push target
is X, the items at the tail of the AIL have LSN X and they don't get
pushed. The push work then completes thinking it is done, and cannot
be restarted until the push target increases to >= X + 1. If the
push target then never increases (because the tail is not moving),
then we never run the push work again and we stall.
Fix it by making sure log items with a LSN that matches the target
exactly are pushed during the loop.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit cb64026b6e)
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. The main cause is a
regression where a work exit path fails to clear the PUSHING state
and recheck the target correctly.
Make both exit paths do the same PUSHING bit clearing and target
checking when the "no more work to be done" condition is hit.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit ea35a20021)
On a 32 bit highmem PowerPC machine, the XFS inode cache was growing
without bound and exhausting low memory causing the OOM killer to be
triggered. After some effort, the problem was reproduced on a 32 bit
x86 highmem machine.
The problem is that the per-ag inode reclaim index cursor was not
getting reset to the start of the AG if the radix tree tag lookup
found no more reclaimable inodes. Hence every further reclaim
attempt started at the same index beyond where any reclaimable
inodes lay, and no further background reclaim ever occurred from the
AG.
Without background inode reclaim the VM driven cache shrinker
simply cannot keep up with cache growth, and OOM is the result.
While the change that exposed the problem was the conversion of the
inode reclaim to use work queues for background reclaim, it was not
the cause of the bug. The bug was introduced when the cursor code
was added, just waiting for some weird configuration to strike....
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Tested-By: Christian Kujau <lists@nerdbynature.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit b223221956)
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. One is caused by a
race condition in determining whether there is a psh in progress or
not.
The XFS_AIL_PUSHING_BIT is used to determine whether a push is
currently in progress. When the AIL push work completes, it checked
whether the target changed and cleared the PUSHING bit to allow a
new push to be requeued. The race condition is as follows:
Thread 1 push work
smp_wmb()
smp_rmb()
check ailp->xa_target unchanged
update ailp->xa_target
test/set PUSHING bit
does not queue
clear PUSHING bit
does not requeue
Now that the push target is updated, new attempts to push the AIL
will not trigger as the push target will be the same, and hence
despite trying to push the AIL we won't ever wake it again.
The fix is to ensure that the AIL push work clears the PUSHING bit
before it checks if the target is unchanged.
As a result, both push triggers operate on the same test/set bit
criteria, so even if we race in the push work and miss the target
update, the thread requesting the push will still set the PUSHING
bit and queue the push work to occur. For safety sake, the same
queue check is done if the push work detects the target change,
though only one of the two will will queue new work due to the use
of test_and_set_bit() checks.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. One of the problems
noticed was that updates of the push target are not 32 bit safe as
the target is a 64 bit value.
We cannot copy a 64 bit LSN without the possibility of corrupting
the result when racing with another updating thread. We have
function to do this update safely without needing to care about
32/64 bit issues - xfs_trans_ail_copy_lsn() - so use that when
updating the AIL push target.
Also move the reading of the target in the push work inside the AIL
lock, and use XFS_LSN_CMP() for the unlocked comparison during work
termination to close read holes as well.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. One of the problems
discovered is a target mismatch between the item pushing loop and
the target itself.
The push trigger checks for the target increasing (i.e. new target >
current) while the push loop only pushes items that have a LSN <
current. As a result, we can get the situation where the push target
is X, the items at the tail of the AIL have LSN X and they don't get
pushed. The push work then completes thinking it is done, and cannot
be restarted until the push target increases to >= X + 1. If the
push target then never increases (because the tail is not moving),
then we never run the push work again and we stall.
Fix it by making sure log items with a LSN that matches the target
exactly are pushed during the loop.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
The recent conversion of the xfsaild functionality to a work queue
introduced a hard-to-hit log space grant hang. The main cause is a
regression where a work exit path fails to clear the PUSHING state
and recheck the target correctly.
Make both exit paths do the same PUSHING bit clearing and target
checking when the "no more work to be done" condition is hit.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
On a 32 bit highmem PowerPC machine, the XFS inode cache was growing
without bound and exhausting low memory causing the OOM killer to be
triggered. After some effort, the problem was reproduced on a 32 bit
x86 highmem machine.
The problem is that the per-ag inode reclaim index cursor was not
getting reset to the start of the AG if the radix tree tag lookup
found no more reclaimable inodes. Hence every further reclaim
attempt started at the same index beyond where any reclaimable
inodes lay, and no further background reclaim ever occurred from the
AG.
Without background inode reclaim the VM driven cache shrinker
simply cannot keep up with cache growth, and OOM is the result.
While the change that exposed the problem was the conversion of the
inode reclaim to use work queues for background reclaim, it was not
the cause of the bug. The bug was introduced when the cursor code
was added, just waiting for some weird configuration to strike....
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Tested-By: Christian Kujau <lists@nerdbynature.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
XFS_IOC_ZERO_RANGE uses struct xfs_flock64, and thus requires argument
translation for 32-bit binaries on x86. Add the required
XFS_IOC_ZERO_RANGE_32 defined and add it to the list of commands that
require xfs_flock64 translation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
xfs_fsblock_t may be a 32-bit type on if XFS_BIG_BLKNOS is not set,
make sure to cast a value of this type to an unsigned long long
before using the ll printk qualifier.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
follow these guidelines:
- leave initialization in the declaration block if it fits the line
- move to the code where it's more suitable ('for' init block)
The last chunk was modified from David's original to be a correct
fix for what appeared to be a duplicate initialization.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Instead of finding the per-ag and then taking and releasing the pagb_lock
for every single busy extent completed sort the list of busy extents and
only switch betweens AGs where nessecary. This becomes especially important
with the online discard support which will hit this lock more often.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Update the extent tree in case we have to reuse a busy extent, so that it
always is kept uptodate. This is done by replacing the busy list searches
with a new xfs_alloc_busy_reuse helper, which updates the busy extent tree
in case of a reuse. This allows us to allow reusing metadata extents
unconditionally, and thus avoid log forces especially for allocation btree
blocks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Every time we reallocate a busy extent, we cause a synchronous log force
to occur to ensure the freeing transaction is on disk before we continue
and use the newly allocated extent. This is extremely sub-optimal as we
have to mark every transaction with blocks that get reused as synchronous.
Instead of searching the busy extent list after deciding on the extent to
allocate, check each candidate extent during the allocation decisions as
to whether they are in the busy list. If they are in the busy list, we
trim the busy range out of the extent we have found and determine if that
trimmed range is still OK for allocation. In many cases, this check can
be incorporated into the allocation extent alignment code which already
does trimming of the found extent before determining if it is a valid
candidate for allocation.
Based on earlier patches from Dave Chinner.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
While we need to make sure we do not reuse busy extents, there is no need
to force out busy extents when moving them between the AGFL and the
freespace btree as we still take care of that when doing the real allocation.
To avoid the log force when just moving extents from the different free
space tracking structures, move the busy search out of
xfs_alloc_get_freelist into the callers that need it, and move the busy
list insert from xfs_free_ag_extent which is used both by AGFL refills
and real allocation to xfs_free_extent, which is only used by the latter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Commit 957935dc ("xfs: fix xfs_debug warnings" broke the logic in
__xfs_printk(). Instead of only printing one of two possible output
strings based on whether the fs has a name or not, it outputs both.
Fix it to only output one message again.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: use proper interfaces for on-stack plugging
xfs: fix xfs_debug warnings
xfs: fix variable set but not used warnings
xfs: convert log tail checking to a warning
xfs: catch bad block numbers freeing extents.
xfs: push the AIL from memory reclaim and periodic sync
xfs: clean up code layout in xfs_trans_ail.c
xfs: convert the xfsaild threads to a workqueue
xfs: introduce background inode reclaim work
xfs: convert ENOSPC inode flushing to use new syncd workqueue
xfs: introduce a xfssyncd workqueue
xfs: fix extent format buffer allocation size
xfs: fix unreferenced var error in xfs_buf.c
Also, applied patch from Tony Luck that fixes ia64:
xfs_destroy_workqueues() should not be tagged with__exit
in the branch before merging.
ia64 throws away .exit sections for the built-in CONFIG case, so routines
that are used in other circumstances should not be tagged as __exit.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add proper blk_start_plug/blk_finish_plug pairs for the two places where
we issue buffer I/O, and remove the blk_flush_plug in xfs_buf_lock and
xfs_buf_iowait, given that context switches already flush the per-process
plugging lists.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
For a CONFIG_XFS_DEBUG=n build gcc complains about statements with no
effect in xfs_debug:
fs/xfs/quota/xfs_qm_syscalls.c: In function 'xfs_qm_scall_trunc_qfiles':
fs/xfs/quota/xfs_qm_syscalls.c:291:3: warning: statement with no effect
The reason for that is that the various new xfs message functions have a
return value which is never used, and in case of the non-debug build
xfs_debug the macro evaluates to a plain 0 which produces the above
warnings. This can be fixed by turning xfs_debug into an inline function
instead of a macro, but in addition to that I've also changed all the
message helpers to return void as we never use their return values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
GCC 4.6 now warnings about variables set but not used. Fix the trivially
fixable warnings of this sort.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
On the Power platform, the log tail debug checks fire excessively
causing the system to panic early in testing. The debug checks are
known to be racy, though on x86_64 there is no evidence that they
trigger at all.
We want to keep the checks active on debug systems to alert us to
problems with log space accounting, but we need to reduce the impact
of a racy check on testing on the Power platform.
As a result, convert the ASSERT conditions to warnings, and
allow them to fire only once per filesystem mount. This will prevent
false positives from interfering with testing, whilst still
providing us with the indication that they may be a problem with log
space accounting should that occur.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
A fuzzed filesystem crashed a kernel when freeing an extent with a
block number beyond the end of the filesystem. Convert all the debug
asserts in xfs_free_extent() to active checks so that we catch bad
extents and return that the filesytsem is corrupted rather than
crashing.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
When we are short on memory, we want to expedite the cleaning of
dirty objects. Hence when we run short on memory, we need to kick
the AIL flushing into action to clean as many dirty objects as
quickly as possible. To implement this, sample the lsn of the log
item at the head of the AIL and use that as the push target for the
AIL flush.
Further, we keep items in the AIL that are dirty that are not
tracked any other way, so we can get objects sitting in the AIL that
don't get written back until the AIL is pushed. Hence to get the
filesystem to the idle state, we might need to push the AIL to flush
out any remaining dirty objects sitting in the AIL. This requires
the same push mechanism as the reclaim push.
This patch also renames xfs_trans_ail_tail() to xfs_ail_min_lsn() to
match the new xfs_ail_max_lsn() function introduced in this patch.
Similarly for xfs_trans_ail_push -> xfs_ail_push.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
This patch rearranges the location of functions in xfs_trans_ail.c
to remove the need for forward declarations of those functions in
preparation for adding new functions without the need for forward
declarations.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Similar to the xfssyncd, the per-filesystem xfsaild threads can be
converted to a global workqueue and run periodically by delayed
works. This makes sense for the AIL pushing because it uses
variable timeouts depending on the work that needs to be done.
By removing the xfsaild, we simplify the AIL pushing code and
remove the need to spread the code to implement the threading
and pushing across multiple files.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Background inode reclaim needs to run more frequently that the XFS
syncd work is run as 30s is too long between optimal reclaim runs.
Add a new periodic work item to the xfs syncd workqueue to run a
fast, non-blocking inode reclaim scan.
Background inode reclaim is kicked by the act of marking inodes for
reclaim. When an AG is first marked as having reclaimable inodes,
the background reclaim work is kicked. It will continue to run
periodically untill it detects that there are no more reclaimable
inodes. It will be kicked again when the first inode is queued for
reclaim.
To ensure shrinker based inode reclaim throttles to the inode
cleaning and reclaim rate but still reclaim inodes efficiently, make it kick the
background inode reclaim so that when we are low on memory we are
trying to reclaim inodes as efficiently as possible. This kick shoul
d not be necessary, but it will protect against failures to kick the
background reclaim when inodes are first dirtied.
To provide the rate throttling, make the shrinker pass do
synchronous inode reclaim so that it blocks on inodes under IO. This
means that the shrinker will reclaim inodes rather than just
skipping over them, but it does not adversely affect the rate of
reclaim because most dirty inodes are already under IO due to the
background reclaim work the shrinker kicked.
These two modifications solve one of the two OOM killer invocations
Chris Mason reported recently when running a stress testing script.
The particular workload trigger for the OOM killer invocation is
where there are more threads than CPUs all unlinking files in an
extremely memory constrained environment. Unlike other solutions,
this one does not have a performance impact on performance when
memory is not constrained or the number of concurrent threads
operating is <= to the number of CPUs.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
On of the problems with the current inode flush at ENOSPC is that we
queue a flush per ENOSPC event, regardless of how many are already
queued. Thi can result in hundreds of queued flushes, most of
which simply burn CPU scanned and do no real work. This simply slows
down allocation at ENOSPC.
We really only need one active flush at a time, and we can easily
implement that via the new xfs_syncd_wq. All we need to do is queue
a flush if one is not already active, then block waiting for the
currently active flush to complete. The result is that we only ever
have a single ENOSPC inode flush active at a time and this greatly
reduces the overhead of ENOSPC processing.
On my 2p test machine, this results in tests exercising ENOSPC
conditions running significantly faster - 042 halves execution time,
083 drops from 60s to 5s, etc - while not introducing test
regressions.
This allows us to remove the old xfssyncd threads and infrastructure
as they are no longer used.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
All of the work xfssyncd does is background functionality. There is
no need for a thread per filesystem to do this work - it can al be
managed by a global workqueue now they manage concurrency
effectively.
Introduce a new gglobal xfssyncd workqueue, and convert the periodic
work to use this new functionality. To do this, use a delayed work
construct to schedule the next running of the periodic sync work
for the filesystem. When the sync work is complete, queue a new
delayed work for the next running of the sync work.
For laptop mode, we wait on completion for the sync works, so ensure
that the sync work queuing interface can flush and wait for work to
complete to enable the work queue infrastructure to replace the
current sequence number and wakeup that is used.
Because the sync work does non-trivial amounts of work, mark the
new work queue as CPU intensive.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
When formatting an inode item, we have to allocate a separate buffer
to hold extents when there are delayed allocation extents on the
inode and it is in extent format. The allocation size is derived
from the in-core data fork representation, which accounts for
delayed allocation extents, while the on-disk representation does
not contain any delalloc extents.
As a result of this mismatch, the allocated buffer can be far larger
than needed to hold the real extent list which, due to the fact the
inode is in extent format, is limited to the size of the literal
area of the inode. However, we can have thousands of delalloc
extents, resulting in an allocation size orders of magnitude larger
than is needed to hold all the real extents.
Fix this by limiting the size of the buffer being allocated to the
size of the literal area of the inodes in the filesystem (i.e. the
maximum size an inode fork can grow to).
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: stop using the page cache to back the buffer cache
xfs: register the inode cache shrinker before quotachecks
xfs: xfs_trans_read_buf() should return an error on failure
xfs: introduce inode cluster buffer trylocks for xfs_iflush
vmap: flush vmap aliases when mapping fails
xfs: preallocation transactions do not need to be synchronous
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_buf.c due to plug removal.
Now that the buffer cache has it's own LRU, we do not need to use
the page cache to provide persistent caching and reclaim
infrastructure. Convert the buffer cache to use alloc_pages()
instead of the page cache. This will remove all the overhead of page
cache management from setup and teardown of the buffers, as well as
needing to mark pages accessed as we find buffers in the buffer
cache.
By avoiding the page cache, we also remove the need to keep state in
the page_private(page) field for persistant storage across buffer
free/buffer rebuild and so all that code can be removed. This also
fixes the long-standing problem of not having enough bits in the
page_private field to track all the state needed for a 512
sector/64k page setup.
It also removes the need for page locking during reads as the pages
are unique to the buffer and nobody else will be attempting to
access them.
Finally, it removes the buftarg address space lock as a point of
global contention on workloads that allocate and free buffers
quickly such as when creating or removing large numbers of inodes in
parallel. This remove the 16TB limit on filesystem size on 32 bit
machines as the page index (32 bit) is no longer used for lookups
of metadata buffers - the buffer cache is now solely indexed by disk
address which is stored in a 64 bit field in the buffer.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
During mount, we can do a quotacheck that involves a bulkstat pass
on all inodes. If there are more inodes in the filesystem than can
be held in memory, we require the inode cache shrinker to run to
ensure that we don't run out of memory.
Unfortunately, the inode cache shrinker is not registered until we
get to the end of the superblock setup process, which is after a
quotacheck is run if it is needed. Hence we need to register the
inode cache shrinker earlier in the mount process so that we don't
OOM during mount. This requires that we also initialise the syncd
work before we register the shrinker, so we nee dto juggle that
around as well.
While there, make sure that we have set up the block sizes in the
VFS superblock correctly before the quotacheck is run so that any
inodes that are cached as a result of the quotacheck have their
block size fields set up correctly.
Cc: stable@kernel.org
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
When inside a transaction and we fail to read a buffer,
xfs_trans_read_buf returns a null buffer pointer and no error.
xfs_do_da_buf() checks the error return, but not the buffer, and as
a result this read failure condition causes a panic when it attempts
to dereference the non-existant buffer.
Make xfs_trans_read_buf() return the same error for this situation
regardless of whether it is in a transaction or not. This means
every caller does not need to check both the error return and the
buffer before proceeding to use the buffer.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
There is an ABBA deadlock between synchronous inode flushing in
xfs_reclaim_inode and xfs_icluster_free. xfs_icluster_free locks the
buffer, then takes inode ilocks, whilst synchronous reclaim takes
the ilock followed by the buffer lock in xfs_iflush().
To avoid this deadlock, separate the inode cluster buffer locking
semantics from the synchronous inode flush semantics, allowing
callers to attempt to lock the buffer but still issue synchronous IO
if it can get the buffer. This requires xfs_iflush() calls that
currently use non-blocking semantics to pass SYNC_TRYLOCK rather
than 0 as the flags parameter.
This allows xfs_reclaim_inode to avoid the deadlock on the buffer
lock and detect the failure so that it can drop the inode ilock and
restart the reclaim attempt on the inode. This allows
xfs_ifree_cluster to obtain the inode lock, mark the inode stale and
release it and hence defuse the deadlock situation. It also has the
pleasant side effect of avoiding IO in xfs_reclaim_inode when it
tries to next reclaim the inode as it is now marked stale.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
On 32 bit systems, vmalloc space is limited and XFS can chew through
it quickly as the vmalloc space is lazily freed. This can result in
failure to map buffers, even when there is apparently large amounts
of vmalloc space available. Hence, if we fail to map a buffer, purge
the aliases that have not yet been freed to hopefuly free up enough
vmalloc space to allow a retry to succeed.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Preallocation and hole punch transactions are currently synchronous
and this is causing performance problems in some cases. The
transactions don't need to be synchronous as we don't need to
guarantee the preallocation is persistent on disk until a
fdatasync, fsync, sync operation occurs. If the file is opened
O_SYNC or O_DATASYNC, only then should the transaction be issued
synchronously.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (23 commits)
xfs: don't name variables "panic"
xfs: factor agf counter updates into a helper
xfs: clean up the xfs_alloc_compute_aligned calling convention
xfs: kill support/debug.[ch]
xfs: Convert remaining cmn_err() callers to new API
xfs: convert the quota debug prints to new API
xfs: rename xfs_cmn_err_fsblock_zero()
xfs: convert xfs_fs_cmn_err to new error logging API
xfs: kill xfs_fs_mount_cmn_err() macro
xfs: kill xfs_fs_repair_cmn_err() macro
xfs: convert xfs_cmn_err to xfs_alert_tag
xfs: Convert xlog_warn to new logging interface
xfs: Convert linux-2.6/ files to new logging interface
xfs: introduce new logging API.
xfs: zero proper structure size for geometry calls
xfs: enable delaylog by default
xfs: more sensible inode refcounting for ialloc
xfs: stop using xfs_trans_iget in the RT allocator
xfs: check if device support discard in xfs_ioc_trim()
xfs: prevent leaking uninitialized stack memory in FSGEOMETRY_V1
...
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
Replace EXTRA_CFLAGS with ccflags-y. And change ntfs-objs to ntfs-y
for cleaner conditional inclusion.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (33 commits)
AppArmor: kill unused macros in lsm.c
AppArmor: cleanup generated files correctly
KEYS: Add an iovec version of KEYCTL_INSTANTIATE
KEYS: Add a new keyctl op to reject a key with a specified error code
KEYS: Add a key type op to permit the key description to be vetted
KEYS: Add an RCU payload dereference macro
AppArmor: Cleanup make file to remove cruft and make it easier to read
SELinux: implement the new sb_remount LSM hook
LSM: Pass -o remount options to the LSM
SELinux: Compute SID for the newly created socket
SELinux: Socket retains creator role and MLS attribute
SELinux: Auto-generate security_is_socket_class
TOMOYO: Fix memory leak upon file open.
Revert "selinux: simplify ioctl checking"
selinux: drop unused packet flow permissions
selinux: Fix packet forwarding checks on postrouting
selinux: Fix wrong checks for selinux_policycap_netpeer
selinux: Fix check for xfrm selinux context algorithm
ima: remove unnecessary call to ima_must_measure
IMA: remove IMA imbalance checking
...
* 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix build failure introduced by s/freezeable/freezable/
workqueue: add system_freezeable_wq
rds/ib: use system_wq instead of rds_ib_fmr_wq
net/9p: replace p9_poll_task with a work
net/9p: use system_wq instead of p9_mux_wq
xfs: convert to alloc_workqueue()
reiserfs: make commit_wq use the default concurrency level
ocfs2: use system_wq instead of ocfs2_quota_wq
ext4: convert to alloc_workqueue()
scsi/scsi_tgt_lib: scsi_tgtd isn't used in memory reclaim path
scsi/be2iscsi,qla2xxx: convert to alloc_workqueue()
misc/iwmc3200top: use system_wq instead of dedicated workqueues
i2o: use alloc_workqueue() instead of create_workqueue()
acpi: kacpi*_wq don't need WQ_MEM_RECLAIM
fs/aio: aio_wq isn't used in memory reclaim path
input/tps6507x-ts: use system_wq instead of dedicated workqueue
cpufreq: use system_wq instead of dedicated workqueues
wireless/ipw2x00: use system_wq instead of dedicated workqueues
arm/omap: use system_wq in mailbox
workqueue: use WQ_MEM_RECLAIM instead of WQ_RESCUER
The exportfs encode handle function should return the minimum required
handle size. This helps user to find out the handle size by passing 0
handle size in the first step and then redoing to the call again with
the returned handle size value.
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The new xfs_alert_tag() used a variable named "panic",
and that is to be avoided. Rename it.
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
With the plugging now being explicitly controlled by the
submitter, callers need not pass down unplugging hints
to the block layer. If they want to unplug, it's because they
manually plugged on their own - in which case, they should just
unplug at will.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Updating the AGF and transactions counters is duplicated between allocating
and freeing extents. Factor the code into a common helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Pass a xfs_alloc_arg structure to xfs_alloc_compute_aligned and derive
the alignment and minlen paramters from it. This cleans up the existing
callers, and we'll need even more information from the xfs_alloc_arg
in subsequent patches. Based on a patch from Dave Chinner.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The remaining functionality in debug.[ch] is effectively just assert
handling, conditional debug definitions and hex dumping. The hex
dumping and assert function can be moved into the new printk module,
while the rest can be moved into top-level header files. This allows
fs/xfs/support/debug.[ch] to be completely removed from the
codebase.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Once converted, kill the remainder of the cmn_err() interface.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The "cmn_err" part of the function name is no longer relevant. Rename
the function to xfs_alert_fsblock_zero() to match the new logging
API.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Continue to clean up the error logging code by converting all the
callers of xfs_fs_cmn_err() to the new API. Once done, remove the
unused old API function.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The xfs_fs_mount_cmn_err() hides a simple check as to whether the
mount path should output an error or not. Remove the macro and open
code the check.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In certain cases of inode corruption, the xfs_fs_repair_cmn_err()
macro is used to output an extra message in the corruption report.
That extra message is "unmount and run xfs_repair", which really
applies to any corruption report. Each case that this macro is
called (except one) a following call to xfs_corruption_error() is
made to optionally dump more information about the error.
Hence, move the output of "run xfs_repair" to xfs_corruption_error()
so that it is output on all corruption reports. Also, convert the
callers of the repair macro that don't call xfs_corruption_error()
to call it, hence provide consiѕtent error reporting for all cases
where xfs_fs_repair_cmn_err() used to be called.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Continue the conversion of the old cmn_err interface be converting
all the conditional panic tag errors to xfs_alert_tag() and then
removing xfs_cmn_err().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Convert the xfs log operations to use the new error logging
interfaces. This removes the xlog_{warn,panic} wrappers and makes
almost all errors emit the device they belong to instead of just
refering to "XFS".
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Convert the files in fs/xfs/linux-2.6/ to use the new xfs_<level>
logging format that replaces the old Irix inherited cmn_err()
interfaces. While there, also convert naked printk calls to use the
relevant xfs logging function to standardise output format.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Commit 493f3358cb added this call to
xfs_fs_geometry() in order to avoid passing kernel stack data back
to user space:
+ memset(geo, 0, sizeof(*geo));
Unfortunately, one of the callers of that function passes the
address of a smaller data type, cast to fit the type that
xfs_fs_geometry() requires. As a result, this can happen:
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted
in: f87aca93
Pid: 262, comm: xfs_fsr Not tainted 2.6.38-rc6-493f3358cb2+ #1
Call Trace:
[<c12991ac>] ? panic+0x50/0x150
[<c102ed71>] ? __stack_chk_fail+0x10/0x18
[<f87aca93>] ? xfs_ioc_fsgeometry_v1+0x56/0x5d [xfs]
Fix this by fixing that one caller to pass the right type and then
copy out the subset it is interested in.
Note: This patch is an alternative to one originally proposed by
Eric Sandeen.
Reported-by: Jeffrey Hundstad <jeffrey.hundstad@mnsu.edu>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Tested-by: Jeffrey Hundstad <jeffrey.hundstad@mnsu.edu>
Most of the logging infrastructure in XFS is unneccessary and
designed around the infrastructure supplied by Irix rather than
Linux. To rationalise the logging interfaces, start by introducing
simple printk wrappers similar to the dev_printk() infrastructure.
Later patches will convert code to use this new interface.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Commit 493f3358cb added this call to
xfs_fs_geometry() in order to avoid passing kernel stack data back
to user space:
+ memset(geo, 0, sizeof(*geo));
Unfortunately, one of the callers of that function passes the
address of a smaller data type, cast to fit the type that
xfs_fs_geometry() requires. As a result, this can happen:
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted
in: f87aca93
Pid: 262, comm: xfs_fsr Not tainted 2.6.38-rc6-493f3358cb2+ #1
Call Trace:
[<c12991ac>] ? panic+0x50/0x150
[<c102ed71>] ? __stack_chk_fail+0x10/0x18
[<f87aca93>] ? xfs_ioc_fsgeometry_v1+0x56/0x5d [xfs]
Fix this by fixing that one caller to pass the right type and then
copy out the subset it is interested in.
Note: This patch is an alternative to one originally proposed by
Eric Sandeen.
Reported-by: Jeffrey Hundstad <jeffrey.hundstad@mnsu.edu>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Tested-by: Jeffrey Hundstad <jeffrey.hundstad@mnsu.edu>
Currently we return iodes from xfs_ialloc with just a single reference held.
But we need two references, as one is dropped during transaction commit and
the second needs to be transfered to the VFS. Change xfs_ialloc to use
xfs_iget plus xfs_trans_ijoin_ref to grab two references to the inode,
and remove the now superflous IHOLD calls from all callers. This also
greatly simplifies the error handling in xfs_create and also allow to remove
xfs_trans_iget as no other callers are left.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
During mount we establish references to the RT inodes, which we keep for
the lifetime of the filesystem. Instead of using xfs_trans_iget to grab
additional references when adding RT inodes to transactions use the
combination of xfs_ilock and xfs_trans_ijoin_ref, which archives the same
end result with less overhead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Right now we, are relying on the fact that when we attempt to
actually do the discard, blkdev_issue_discar() returns -EOPNOTSUPP
and the user is informed that the device does not support discard.
However, in the case where the we do not hit any suitable free
extent to trim in FITRIM code, it will finish without any error.
This is very confusing, because it seems that FITRIM was successful
even though the device does not actually supports discard.
Solution: Check for the discard support before attempt to search for
free extents.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The FSGEOMETRY_V1 ioctl (and its compat equivalent) calls out to
xfs_fs_geometry() with a version number of 3. This code path does not
fill in the logsunit member of the passed xfs_fsop_geom_t, leading to
the leaking of four bytes of uninitialized stack data to potentially
unprivileged callers.
v2 switches to memset() to avoid future issues if structure members
change, on suggestion of Dave Chinner.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.org>
Signed-off-by: Alex Elder <aelder@sgi.com>
Right now we, are relying on the fact that when we attempt to
actually do the discard, blkdev_issue_discar() returns -EOPNOTSUPP
and the user is informed that the device does not support discard.
However, in the case where the we do not hit any suitable free
extent to trim in FITRIM code, it will finish without any error.
This is very confusing, because it seems that FITRIM was successful
even though the device does not actually supports discard.
Solution: Check for the discard support before attempt to search for
free extents.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The FSGEOMETRY_V1 ioctl (and its compat equivalent) calls out to
xfs_fs_geometry() with a version number of 3. This code path does not
fill in the logsunit member of the passed xfs_fsop_geom_t, leading to
the leaking of four bytes of uninitialized stack data to potentially
unprivileged callers.
v2 switches to memset() to avoid future issues if structure members
change, on suggestion of Dave Chinner.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.org>
Signed-off-by: Alex Elder <aelder@sgi.com>
The rt bitmap and summary inodes do not participate in the normal inode
locking protocol. Instead the rt bitmap inode can be locked in any
transaction involving rt allocations, and the both of the rt inodes can
be locked at the same time. Add specific lockdep subclasses for the rt
inodes to prevent lockdep from blowing up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
We can easily set the extsize flag without setting an extent size
hint, or one that evaluates to zero. Historically the di_extsize
field was only used when it was non-zero, but the commit
"Cleanup inode extent size hint extraction"
broke this. Restore the old behaviour, thus fixing xfsqa 090 with
a debug kernel.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Currently both xfs_rtpick_extent and xfs_rtallocate_extent call
xfs_trans_iget to grab and lock the rt bitmap inode, which results in a
deadlock since the removal of the lock recursion counters in commit
"xfs: simplify inode to transaction joining"
Fix this by acquiring and locking the inode in xfs_bmap_rtalloc before
calling into xfs_rtpick_extent and xfs_rtallocate_extent.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
SELinux would like to implement a new labeling behavior of newly created
inodes. We currently label new inodes based on the parent and the creating
process. This new behavior would also take into account the name of the
new object when deciding the new label. This is not the (supposed) full path,
just the last component of the path.
This is very useful because creating /etc/shadow is different than creating
/etc/passwd but the kernel hooks are unable to differentiate these
operations. We currently require that userspace realize it is doing some
difficult operation like that and than userspace jumps through SELinux hoops
to get things set up correctly. This patch does not implement new
behavior, that is obviously contained in a seperate SELinux patch, but it
does pass the needed name down to the correct LSM hook. If no such name
exists it is fine to pass NULL.
Signed-off-by: Eric Paris <eparis@redhat.com>
Convert from create[_singlethread]_workqueue() to alloc_workqueue().
* xfsdatad_workqueue and xfsconvertd_workqueue are identity converted.
Using higher concurrency limit might be useful but given the
complexity of workqueue usage in xfs, proceeding cautiously seems
better.
* xfs_mru_reap_wq is converted to non-ordered workqueue with max
concurrency of 1 as the work items don't require any specific
ordering and already have proper synchronization. It seems it was
singlethreaded to save worker threads, which is no longer a concern.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Hellwig <hch@infradead.org>
When filling in the middle of a previous delayed allocation in
xfs_bmap_add_extent_delay_real, set br_startblock of the new delay
extent to the right to nullstartblock instead of 0 before inserting
the extent into the ifork (xfs_iext_insert), rather than setting
br_startblock afterward.
Adding the extent into the ifork with br_startblock=0 can lead to
the extent being copied into the btree by xfs_bmap_extent_to_btree
if we happen to convert from extents format to btree format before
updating br_startblock with the correct value. The unexpected
addition of this delay extent to the btree can cause subsequent
XFS_WANT_CORRUPTED_GOTO filesystem shutdown in several
xfs_bmap_add_extent_delay_real cases where we are converting a delay
extent to real and unexpectedly find an extent already inserted.
For example:
911 case BMAP_LEFT_FILLING:
912 /*
913 * Filling in the first part of a previous delayed allocation.
914 * The left neighbor is not contiguous.
915 */
916 trace_xfs_bmap_pre_update(ip, idx, state, _THIS_IP_);
917 xfs_bmbt_set_startoff(ep, new_endoff);
918 temp = PREV.br_blockcount - new->br_blockcount;
919 xfs_bmbt_set_blockcount(ep, temp);
920 xfs_iext_insert(ip, idx, 1, new, state);
921 ip->i_df.if_lastex = idx;
922 ip->i_d.di_nextents++;
923 if (cur == NULL)
924 rval = XFS_ILOG_CORE | XFS_ILOG_DEXT;
925 else {
926 rval = XFS_ILOG_CORE;
927 if ((error = xfs_bmbt_lookup_eq(cur, new->br_startoff,
928 new->br_startblock, new->br_blockcount,
929 &i)))
930 goto done;
931 XFS_WANT_CORRUPTED_GOTO(i == 0, done);
With the bogus extent in the btree we shutdown the filesystem at
931. The conversion from extents to btree format happens when the
number of extents in the inode increases above ip->i_df.if_ext_max.
xfs_bmap_extent_to_btree copies extents from the ifork into the
btree, ignoring all delalloc extents which are denoted by
br_startblock having some value of nullstartblock.
SGI-PV: 1013221
Signed-off-by: Ben Myers <bpm@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Commit 368e136 ("xfs: remove duplicate code from dquot reclaim") fails
to unlock the dquot freelist when the number of loop restarts is
exceeded in xfs_qm_dqreclaim_one(). This causes hangs in memory
reclaim.
Rework the loop control logic into an unwind stack that all the
different cases jump into. This means there is only one set of code
that processes the loop exit criteria, and simplifies the unlocking
of all the items from different points in the loop. It also fixes a
double increment of the restart counter from the qi_dqlist_lock
case.
Reported-by: Malcolm Scott <lkml@malc.org.uk>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Failure to commit a transaction into the CIL is not handled
correctly. This currently can only happen when racing with a
shutdown and requires an explicit shutdown check, so it rare and can
be avoided. Remove the shutdown check and make the CIL commit a void
function to indicate it will always succeed, thereby removing the
incorrectly handled failure case.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
The extent size hint can be set to larger than an AG. This means
that the alignment process can push the range to be allocated
outside the bounds of the AG, resulting in assert failures or
corrupted bmbt records. Similarly, if the extsize is larger than the
maximum extent size supported, the alignment process will produce
extents that are too large to fit into the bmbt records, resulting
in a different type of assert/corruption failure.
Fix this by limiting extsize at the time іt is set firstly to be
less than MAXEXTLEN, then to be a maximum of half the size of the
AGs in the filesystem for non-realtime inodes. Realtime inodes do
not allocate out of AGs, so don't have to be restricted by the size
of AGs.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
When doing delayed allocation, if the allocation size is for a
maximally sized extent, extent size alignment can push it over this
limit. This results in an assert failure in xfs_bmbt_set_allf() as
the extent length is too large to find in the extent record.
Fix this by ensuring that we allow for space that extent size
alignment requires (up to 2 * (extsize -1) blocks as we have to
handle both head and tail alignment) when limiting the maximum size
of the extent.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Delayed allocation extents can be larger than AGs, so when trying to
convert a large range we may scan every AG inside
xfs_bmap_alloc_nullfb() trying to find an AG with a size larger than
an AG. We should stop when we find the first AG with a maximum
possible allocation size. This causes excessive CPU usage when there
are lots of AGs.
The same problem occurs when doing preallocation of a range larger
than an AG.
Fix the problem by limiting real allocation lengths to the maximum
that an AG can support. This means if we have empty AGs, we'll stop
the search at the first of them. If there are no empty AGs, we'll
still scan them all, but that is a different problem....
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
rounddown_power_of_2() returns an undefined result when passed a
value of zero. The specualtive delayed allocation code is doing this
when the inode is zero length. Hence occasionally the preallocation
is much, much larger than is necessary (e.g. 8GB for a 270 _byte_
file). Ensure we don't even pass a zero value to this function so
the result of preallocation is always the desired size.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
After test 139, kmemleak shows:
unreferenced object 0xffff880078b405d8 (size 400):
comm "xfs_io", pid 4904, jiffies 4294909383 (age 1186.728s)
hex dump (first 32 bytes):
60 c1 17 79 00 88 ff ff 60 c1 17 79 00 88 ff ff `..y....`..y....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff81afb04d>] kmemleak_alloc+0x2d/0x60
[<ffffffff8115c6cf>] kmem_cache_alloc+0x13f/0x2b0
[<ffffffff814aaa97>] kmem_zone_alloc+0x77/0xf0
[<ffffffff814aab2e>] kmem_zone_zalloc+0x1e/0x50
[<ffffffff8147cd6b>] xfs_efi_init+0x4b/0xb0
[<ffffffff814a4ee8>] xfs_trans_get_efi+0x58/0x90
[<ffffffff81455fab>] xfs_bmap_finish+0x8b/0x1d0
[<ffffffff814851b4>] xfs_itruncate_finish+0x2c4/0x5d0
[<ffffffff814a970f>] xfs_setattr+0x8df/0xa70
[<ffffffff814b5c7b>] xfs_vn_setattr+0x1b/0x20
[<ffffffff8117dc00>] notify_change+0x170/0x2e0
[<ffffffff81163bf6>] do_truncate+0x66/0xa0
[<ffffffff81163d0b>] sys_ftruncate+0xdb/0xe0
[<ffffffff8103a002>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
The cause of the leak is that the "remove" parameter of IOP_UNPIN()
is never set when a CIL push is aborted. This means that the EFI
item is never freed if it was in the push being cancelled. The
problem is specific to delayed logging, but has uncovered a couple
of problems with the handling of IOP_UNPIN(remove).
Firstly, we cannot safely call xfs_trans_del_item() from IOP_UNPIN()
in the CIL commit failure path or the iclog write failure path
because for delayed loging we have no transaction context. Hence we
must only call xfs_trans_del_item() if the log item being unpinned
has an active log item descriptor.
Secondly, xfs_trans_uncommit() does not handle log item descriptor
freeing during the traversal of log items on a transaction. It can
reference a freed log item descriptor when unpinning an EFI item.
Hence it needs to use a safe list traversal method to allow items to
be removed from the transaction during IOP_UNPIN().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
On platforms that call panic() inside their BUG() macro (m68k/sun3, and
all platforms that don't set HAVE_ARCH_BUG), compilation fails with:
| fs/xfs/support/debug.c: In function ‘xfs_cmn_err’:
| fs/xfs/support/debug.c:92: error: called object ‘panic’ is not a function
as the local variable "panic" conflicts with the "panic()" function.
Rename the local variable to resolve this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently all filesystems except XFS implement fallocate asynchronously,
while XFS forced a commit. Both of these are suboptimal - in case of O_SYNC
I/O we really want our allocation on disk, especially for the !KEEP_SIZE
case where we actually grow the file with user-visible zeroes. On the
other hand always commiting the transaction is a bad idea for fast-path
uses of fallocate like for example in recent Samba versions. Given
that block allocation is a data plane operation anyway change it from
an inode operation to a file operation so that we have the file structure
available that lets us check for O_SYNC.
This also includes moving the code around for a few of the filesystems,
and remove the already unnedded S_ISDIR checks given that we only wire
up fallocate for regular files.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Instead of various home grown checks that might need updates for new
flags just check for any bit outside the mask of the features supported
by the filesystem. This makes the check future proof for any newly
added flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (41 commits)
fs: add documentation on fallocate hole punching
Gfs2: fail if we try to use hole punch
Btrfs: fail if we try to use hole punch
Ext4: fail if we try to use hole punch
Ocfs2: handle hole punching via fallocate properly
XFS: handle hole punching via fallocate properly
fs: add hole punching to fallocate
vfs: pass struct file to do_truncate on O_TRUNC opens (try #2)
fix signedness mess in rw_verify_area() on 64bit architectures
fs: fix kernel-doc for dcache::prepend_path
fs: fix kernel-doc for dcache::d_validate
sanitize ecryptfs ->mount()
switch afs
move internal-only parts of ncpfs headers to fs/ncpfs
switch ncpfs
switch 9p
pass default dentry_operations to mount_pseudo()
switch hostfs
switch affs
switch configfs
...
This patch simply allows XFS to handle the hole punching flag in fallocate
properly. I've tested this with a little program that does a bunch of random
hole punching with FL_KEEP_SIZE and without it to make sure it does the right
thing. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We currently have a global error message buffer in cmn_err that is
protected by a spin lock that disables interrupts. Recently there
have been reports of NMI timeouts occurring when the console is
being flooded by SCSI error reports due to cmn_err() getting stuck
trying to print to the console while holding this lock (i.e. with
interrupts disabled). The NMI watchdog is seeing this CPU as
non-responding and so is triggering a panic. While the trigger for
the reported case is SCSI errors, pretty much anything that spams
the kernel log could cause this to occur.
Realistically the only reason that we have the intemediate message
buffer is to prepend the correct kernel log level prefix to the log
message. The only reason we have the lock is to protect the global
message buffer and the only reason the message buffer is global is
to keep it off the stack. Hence if we can avoid needing a global
message buffer we avoid needing the lock, and we can do this with a
small amount of cleanup and some preprocessor tricks:
1. clean up xfs_cmn_err() panic mask functionality to avoid
needing debug code in xfs_cmn_err()
2. remove the couple of "!" message prefixes that still exist that
the existing cmn_err() code steps over.
3. redefine CE_* levels directly to KERN_*
4. redefine cmn_err() and friends to use printk() directly
via variable argument length macros.
By doing this, we can completely remove the cmn_err() code and the
lock that is causing the problems, and rely solely on printk()
serialisation to ensure that we don't get garbled messages.
A series of followup patches is really needed to clean up all the
cmn_err() calls and related messages properly, but that results in a
series that is not easily back portable to enterprise kernels. Hence
this initial fix is only to address the direct problem in the lowest
impact way possible.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
I received a ppc64 bug report involving xfs but the assertion was
filtered out by the console log level. Use KERN_CRIT to ensure it
makes it out.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
In fs/xfs/xfs_trans.c::xfs_trans_unreserve_and_mod_sb() at the out:
label we have this:
ASSERT(error = 0);
I believe a comparison was intended, not an assignment. If I'm
right, the patch below fixes that up.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Alex Elder <aelder@sgi.com>
If we get an IO error on a synchronous superblock write, we attach an
error release function to it so that when the last reference goes away
the release function is called and the buffer is invalidated and
unlocked. The buffer is left locked until the release function is
called so that other concurrent users of the buffer will be locked out
until the buffer error is fully processed.
Unfortunately, for the superblock buffer the filesyetm itself holds a
reference to the buffer which prevents the reference count from
dropping to zero and the release function being called. As a result,
once an IO error occurs on a sync write, the buffer will never be
unlocked and all future attempts to lock the buffer will hang.
To make matters worse, this problems is not unique to such buffers;
if there is a concurrent _xfs_buf_find() running, the lookup will grab
a reference to the buffer and then wait on the buffer lock, preventing
the reference count from ever falling to zero and hence unlocking the
buffer.
As such, the whole b_relse function implementation is broken because it
cannot rely on the buffer reference count falling to zero to unlock the
errored buffer. The synchronous write error path is the only path that
uses this callback - it is used to ensure that the synchronous waiter
gets the buffer error before the error state is cleared from the buffer
by the release function.
Given that the only sychronous buffer writes now go through xfs_bwrite
and the error path in question can only occur for a write of a dirty,
logged buffer, we can move most of the b_relse processing to happen
inline in xfs_buf_iodone_callbacks, just like a normal I/O completion.
In addition to that we make sure the error is not cleared in
xfs_buf_iodone_callbacks, so that xfs_bwrite can reliably check it.
Given that xfs_bwrite keeps the buffer locked until it has waited for
it and checked the error this allows to reliably propagate the error
to the caller, and make sure that the buffer is reliably unlocked.
Given that xfs_buf_iodone_callbacks was the only instance of the
b_relse callback we can remove it entirely.
Based on earlier patches by Dave Chinner and Ajeet Yadav.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ajeet Yadav <ajeet.yadav.77@gmail.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Allow manual discards from userspace using the FITRIM ioctl. This is not
intended to be run during normal workloads, as the freepsace btree walks
can cause large performance degradation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
To ensure the log is covered and the filesystem idles correctly, we
need to ensure that dummy transactions hit the disk and do not stay
pinned in memory. If the superblock is pinned in memory, it can't
be flushed so the log covering cannot make progress. The result is
dependent on timing - more oftent han not we continue to issues a
log covering transaction every 36s rather than idling after ~90s.
Fix this by making the log covering transaction synchronous. To
avoid additional log force from xfssyncd, make the log covering
transaction take the place of the existing log force in the xfssyncd
background sync process.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
This merge pulls the XFS master branch into the latest Linus master.
This results in a merge conflict whose best fix is not obvious.
I manually fixed the conflict, in "fs/xfs/xfs_iget.c".
Dave Chinner had done work that resulted in RCU freeing of inodes
separate from what Nick Piggin had done, and their results differed
slightly in xfs_inode_free(). The fix updates Nick's call_rcu()
with the use of VFS_I(), while incorporating needed updates to some
XFS inode fields implemented in Dave's series. Dave's RCU callback
function has also been removed.
Signed-off-by: Alex Elder <aelder@sgi.com>
When two concurrent unaligned, non-overlapping direct IOs are issued
to the same block, the direct Io layer will race to zero the block.
The result is that one of the concurrent IOs will overwrite data
written by the other IO with zeros. This is demonstrated by the
xfsqa test 240.
To avoid this problem, serialise all unaligned direct IOs to an
inode with a big hammer. We need a big hammer approach as we need to
serialise AIO as well, so we can't just block writes on locks.
Hence, the big hammer is calling xfs_ioend_wait() while holding out
other unaligned direct IOs from starting.
We don't bother trying to serialised aligned vs unaligned IOs as
they are overlapping IO and the result of concurrent overlapping IOs
is undefined - the result of either IO is a valid result so we let
them race. Hence we only penalise unaligned IO, which already has a
major overhead compared to aligned IO so this isn't a major problem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The buffered IO and direct IO write paths share a common set of
checks and limiting code prior to issuing the write. Factor that
into a common helper function.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Complete the split of the different write IO paths by splitting the
buffered IO write path out of xfs_file_aio_write(). This makes the
different mechanisms of the write patchs easier to follow.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The current xfs_file_aio_write code is a mess of locking shenanigans
to handle the different locking requirements of buffered and direct
IO. Start to clean this up by disentangling the direct IO path from
the mess.
This also removes the failed direct IO fallback path to buffered IO.
XFS handles all direct IO cases without needing to fall back to
buffered IO, so we can safely remove this unused path. This greatly
simplifies the logic and locking needed in the write path.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We need to obtain the i_mutex, i_iolock and i_ilock during the read
and write paths. Add a set of wrapper functions to neatly
encapsulate the lock ordering and shared/exclusive semantics to make
the locking easier to follow and get right.
Note that this changes some of the exclusive locking serialisation in
that serialisation will occur against the i_mutex instead of the
XFS_IOLOCK_EXCL. This does not change any behaviour, and it is
arguably more efficient to use the mutex for such serialisation than
the rw_sem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
xfs_file_aio_write() only returns the error from synchronous
flushing of the data and inode if error == 0. At the point where
error is being checked, it is guaranteed to be > 0. Therefore any
errors returned by the data or fsync flush will never be returned.
Fix the checks so we overwrite the current error once and only if an
error really occurred.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
This simple implementation just checks for no ACLs on the inode, and
if so, then the rcu-walk may proceed, otherwise fail it.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
RCU free the struct inode. This will allow:
- Subsequent store-free path walking patch. The inode must be consulted for
permissions when walking, so an RCU inode reference is a must.
- sb_inode_list_lock to be moved inside i_lock because sb list walkers who want
to take i_lock no longer need to take sb_inode_list_lock to walk the list in
the first place. This will simplify and optimize locking.
- Could remove some nested trylock loops in dcache code
- Could potentially simplify things a bit in VM land. Do not need to take the
page lock to follow page->mapping.
The downsides of this is the performance cost of using RCU. In a simple
creat/unlink microbenchmark, performance drops by about 10% due to inability to
reuse cache-hot slab objects. As iterations increase and RCU freeing starts
kicking over, this increases to about 20%.
In cases where inode lifetimes are longer (ie. many inodes may be allocated
during the average life span of a single inode), a lot of this cache reuse is
not applicable, so the regression caused by this patch is smaller.
The cache-hot regression could largely be avoided by using SLAB_DESTROY_BY_RCU,
however this adds some complexity to list walking and store-free path walking,
so I prefer to implement this at a later date, if it is shown to be a win in
real situations. I haven't found a regression in any non-micro benchmark so I
doubt it will be a problem.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The only thing that the grant lock remains to protect is the grant head
manipulations when adding or removing space from the log. These calculations
are already based on atomic variables, so we can already update them safely
without locks. However, the grant head manpulations require atomic multi-step
calculations to be executed, which the algorithms currently don't allow.
To make these multi-step calculations atomic, convert the algorithms to
compare-and-exchange loops on the atomic variables. That is, we sample the old
value, perform the calculation and use atomic64_cmpxchg() to attempt to update
the head with the new value. If the head has not changed since we sampled it,
it will succeed and we are done. Otherwise, we rerun the calculation again from
a new sample of the head.
This allows us to remove the grant lock from around all the grant head space
manipulations, and that effectively removes the grant lock from the log
completely. Hence we can remove the grant lock completely from the log at this
point.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The log grant ticket wait queues are currently protected by the log
grant lock. However, the queues are functionally independent from
each other, and operations on them only require serialisation
against other queue operations now that all of the other log
variables they use are atomic values.
Hence, we can make them independent of the grant lock by introducing
new locks just to protect the lists operations. because the lists
are independent, we can use a lock per list and ensure that reserve
and write head queuing do not contend.
To ensure forced shutdowns work correctly in conjunction with the
new fast paths, ensure that we check whether the log has been shut
down in the grant functions once we hold the relevant spin locks but
before we go to sleep. This is needed to co-ordinate correctly with
the wakeups that are issued on the ticket queues so we don't leave
any processes sleeping on the queues during a shutdown.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
Now that we don't mark VFS inodes dirty anymore for internal
timestamp changes, but rely on the transaction subsystem to push
them out, we need to explicitly log the source inode in rename after
updating it's timestamps to make sure the changes actually get
forced out by sync/fsync or an AIL push.
We already account for the fourth inode in the log reservation, as a
rename of directories needs to update the nlink field, so just
adding the xfs_trans_log_inode call is enough.
This fixes the xfsqa 065 regression introduced by:
"xfs: don't use vfs writeback for pure metadata modifications"
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Convert the log grant heads to atomic64_t types in preparation for
converting the accounting algorithms to atomic operations. his patch
just converts the variables; the algorithmic changes are in a
separate patch for clarity.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
log->l_tail_lsn is currently protected by the log grant lock. The
lock is only needed for serialising readers against writers, so we
don't really need the lock if we make the l_tail_lsn variable an
atomic. Converting the l_tail_lsn variable to an atomic64_t means we
can start to peel back the grant lock from various operations.
Also, provide functions to safely crack an atomic LSN variable into
it's component pieces and to recombined the components into an
atomic variable. Use them where appropriate.
This also removes the need for explicitly holding a spinlock to read
the l_tail_lsn on 32 bit platforms.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
log->l_last_sync_lsn is updated in only one critical spot - log
buffer Io completion - and is protected by the grant lock here. This
requires the grant lock to be taken for every log buffer IO
completion. Converting the l_last_sync_lsn variable to an atomic64_t
means that we do not need to take the grant lock in log buffer IO
completion to update it.
This also removes the need for explicitly holding a spinlock to read
the l_last_sync_lsn on 32 bit platforms.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The xlog_grant_push_ail() currently takes the grant lock internally to sample
the tail lsn, last sync lsn and the reserve grant head. Most of the callers
already hold the grant lock but have to drop it before calling
xlog_grant_push_ail(). This is a left over from when the AIL tail pushing was
done in line and hence xlog_grant_push_ail had to drop the grant lock. AIL push
is now done in another thread and hence we can safely hold the grant lock over
the entire xlog_grant_push_ail call.
Push the grant lock outside of xlog_grant_push_ail() to simplify the locking
and synchronisation needed for tail pushing. This will reduce traffic on the
grant lock by itself, but this is only one step in preparing for the complete
removal of the grant lock.
While there, clean up the formatting of xlog_grant_push_ail() to match the
rest of the XFS code.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The log grant queues are one of the few places left using sv_t
constructs for waiting. Given we are touching this code, we should
convert them to plain wait queues. While there, convert all the
other sv_t users in the log code as well.
Seeing as this removes the last users of the sv_t type, remove the
header file defining the wrapper and the fragments that still
reference it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Prepare for switching the grant heads to atomic variables by
combining the two 32 bit values that make up the grant head into a
single 64 bit variable. Provide wrapper functions to combine and
split the grant heads appropriately for calculations and use them as
necessary.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The log grant space calculations are repeated for both write and
reserve grant heads. To make it simpler to convert the calculations
toa different algorithm, factor them so both the gratn heads use the
same calculation functions. Once this is done we can drop the
wrappers that are used in only a couple of place to update both
grant heads at once as they don't provide any particular value.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Factor repeated debug code out of grant head manipulation functions into a
separate function. This removes ifdef DEBUG spagetti from the code and makes
the code easier to follow.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The grant write and reserve queues use a roll-your-own double linked
list, so convert it to a standard list_head structure and convert
all the list traversals to use list_for_each_entry(). We can also
get rid of the XLOG_TIC_IN_Q flag as we can use the list_empty()
check to tell if the ticket is in a list or not.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We now have two copies of AIL delete operations that are mostly
duplicate functionality. The single log item deletes can be
implemented via the bulk updates by turning xfs_trans_ail_delete()
into a simple wrapper. This removes all the duplicate delete
functionality and associated helpers.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We now have two copies of AIL insert operations that are mostly
duplicate functionality. The single log item updates can be
implemented via the bulk updates by turning xfs_trans_ail_update()
into a simple wrapper. This removes all the duplicate insert
functionality and associated helpers.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When inode buffer IO completes, usually all of the inodes are removed from the
AIL. This involves processing them one at a time and taking the AIL lock once
for every inode. When all CPUs are processing inode IO completions, this causes
excessive amount sof contention on the AIL lock.
Instead, change the way we process inode IO completion in the buffer
IO done callback. Allow the inode IO done callback to walk the list
of IO done callbacks and pull all the inodes off the buffer in one
go and then process them as a batch.
Once all the inodes for removal are collected, take the AIL lock
once and do a bulk removal operation to minimise traffic on the AIL
lock.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
To allow buffer iodone callbacks to consume multiple items off the
callback list, first we need to convert the xfs_buf_do_callbacks()
to consume items and always pull the next item from the head of the
list.
The means the item list walk is never dependent on knowing the
next item on the list and hence allows callbacks to remove items
from the list as well. This allows callbacks to do bulk operations
by scanning the list for identical callbacks, consuming them all
and then processing them in bulk, negating the need for multiple
callbacks of that type.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The xfaild often tries to rest to wait for congestion to pass of for
IO to complete, but is regularly woken in tail-pushing situations.
In severe cases, the xfsaild is getting woken tens of thousands of
times a second. Reduce the number needless wakeups by only waking
the xfsaild if the new target is larger than the old one. Further
make short sleeps uninterruptible as they occur when the xfsaild has
decided it needs to back off to allow some IO to complete and being
woken early is counter-productive.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When inserting items into the AIL from the transaction committed
callbacks, we take the AIL lock for every single item that is to be
inserted. For a CIL checkpoint commit, this can be tens of thousands
of individual inserts, yet almost all of the items will be inserted
at the same point in the AIL because they have the same index.
To reduce the overhead and contention on the AIL lock for such
operations, introduce a "bulk insert" operation which allows a list
of log items with the same LSN to be inserted in a single operation
via a list splice. To do this, we need to pre-sort the log items
being committed into a temporary list for insertion.
The complexity is that not every log item will end up with the same
LSN, and not every item is actually inserted into the AIL. Items
that don't match the commit LSN will be inserted and unpinned as per
the current one-at-a-time method (relatively rare), while items that
are not to be inserted will be unpinned and freed immediately. Items
that are to be inserted at the given commit lsn are placed in a
temporary array and inserted into the AIL in bulk each time the
array fills up.
As a result of this, we trade off AIL hold time for a significant
reduction in traffic. lock_stat output shows that the worst case
hold time is unchanged, but contention from AIL inserts drops by an
order of magnitude and the number of lock traversal decreases
significantly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
xfs_ail_delete() has a needlessly complex interface. It returns the log item
that was passed in for deletion (which the callers then assert is identical to
the one passed in), and callers of xfs_ail_delete() still need to invalidate
current traversal cursors.
Make xfs_ail_delete() return void, move the cursor invalidation inside it, and
clean up the callers just to use the log item pointer they passed in.
While cleaning up, remove the messy and unnecessary "/* ARGUSED */" comments
around all these functions.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
EFI/EFD interactions are protected from races by the AIL lock. They
are the only type of log items that require the the AIL lock to
serialise internal state, so they need to be separated from the AIL
lock before we can do bulk insert operations on the AIL.
To acheive this, convert the counter of the number of extents in the
EFI to an atomic so it can be safely manipulated by EFD processing
without locks. Also, convert the EFI state flag manipulations to use
atomic bit operations so no locks are needed to record state
changes. Finally, use the state bits to determine when it is safe to
free the EFI and clean up the code to do this neatly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
XFS_EFI_CANCELED has not been set in the code base since
xfs_efi_cancel() was removed back in 2006 by commit
065d312e15 ("[XFS] Remove unused
iop_abort log item operation), and even then xfs_efi_cancel() was
never called. I haven't tracked it back further than that (beyond
git history), but it indicates that the handling of EFIs in
cancelled transactions has been broken for a long time.
Basically, when we get an IOP_UNPIN(lip, 1); call from
xfs_trans_uncommit() (i.e. remove == 1), if we don't free the log
item descriptor we leak it. Fix the behviour to be correct and kill
the XFS_EFI_CANCELED flag.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
