Since it's exported we should make sure we're using the prototype
others see.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds ARCH_HAS_CPUFREQ in arch/arm/Kconfig for S5PV210,
and updates mach-s5pv210/Makefile for supporting build CPUFREQ driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds CPUFREQ driver for supporting DFS(Dynamic Frequency Scaling).
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds some CMU(Clock Management Unit) registers for
supporting CPUFREQ and some drivers.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds MOUT_DMC0 and SCLK_DMC0 for checking the dmc0 clock
in CPUFREQ driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Current fout_apll has fixed rate value. So CPUFREQ driver gets
incorrect value when finding current CPU frequency. Because some
operation level need to change APLL.
Added get_rate function for fout_apll can give correct frequency
value when calling get_rate function.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV310 and S5PC210 support more I2C devices than previous SoCs.
Add the device support code for them.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV310 and S5PC210 support total 8 (+ 1 dedicated for HDMI) I2C devices.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The name of the I2C2 and I2C3 interrupt should be IIC2 and IIC3
instead of CAN0 and CAN1.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes I2C2 and I2C3 interrupt name from IRQ_CANX to IRQ_IICX
according other SoCs' I2C interrupt naming rule.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Basically S5P SoCs use the Samsung common VA address mapping where
plat-samsung and use plat-s5p's mapping also. The later is a little
mess. So this patch cleans it up.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Camera devices use the I2C0 and Gyro uese the I2C1 on universal board.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
OneNAND device support for Universal board.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds clock types into platform data to support
external clock divider instead of internal clock divider.
It is defined that what kinds of clock type is used in machine.
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds to change bus width and host capability of HSMMC,
when HSMMC is only configured with another value of bus width
and host capability from default one.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HSMMC for S5PV310(SMDKV310) and
S5PC210(SMDKC210).
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds initialization HSMMC device information.
And HSMMC platform data like card detect, data bus width
and capability is configured.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HSMMC for S5PV310 and S5PC210 and
setup for HSMMC host controller and also related GPIO.
At most 4 channel can be used at the same time.
A user can configure SDHCI data bus as 8bit or 4bit.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch clean up the GPIO code and removes useless GPIO addresses.
It can be calculated with offset, the 'base' member of s3c_gpio_chip
is also initialized in the init function.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When merged patches, missed IRQ_EINT_BIT() definition from commit ea31fd43
(ARM: S5PV210: Add Power Management Support). The IRQ_EINT_BIT() is used
in the Power Management operation (plat-samsung/pm.c).
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add platform data, necessary to use Sony IMX074 camera sensor with AP4EVB.
Note: this does not work reliably without an API to reserve contiguous and
coherent memory for V4L DMA buffers. Such memory reservation has to be added as
soon as a suitable API becomes available.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just as it says, if this is merged along with the other patch, the
driver supports the U300 NAND flash interface.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adding a new flash definition would need less code.
Keep the platform passing flash definition method.
If one flash is both defined in platform data and builtin table,
driver would select the one from platform data first.
By this way, platform could select the timing most suit for itself,
not need to follow the common settings.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Makefile - replace the use of <module>-objs with <module>-y
crypto: hifn_795x - use cancel_delayed_work_sync()
crypto: talitos - sparse check endian fixes
crypto: talitos - fix checkpatch warning
crypto: talitos - fix warning: 'alg' may be used uninitialized in this function
crypto: cryptd - Adding the AEAD interface type support to cryptd
crypto: n2_crypto - Niagara2 driver needs to depend upon CRYPTO_DES
crypto: Kconfig - update broken web addresses
crypto: omap-sham - Adjust DMA parameters
crypto: fips - FIPS requires algorithm self-tests
crypto: omap-aes - OMAP2/3 AES hw accelerator driver
crypto: updates to enable omap aes
padata: add missing __percpu markup in include/linux/padata.h
MAINTAINERS: Add maintainer entries for padata/pcrypt
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
When converting to use s3c_gpio_cfgpin_range() the function for the
IISv4 block appears to have been typoed as 4 (the keypad) rather than
5 as it should be.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes code setting special-function and no pull-up
to use the s3c_gpio_cfgrange_nopull() wrapper.
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes code setting special-function and no pull-up
to use the s3c_gpio_cfgrange_nopull() wrapper.
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes code setting special-function and no pull-up
to use the s3c_gpio_cfgrange_nopull() wrapper.
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change code setting special-function and no pull-up to use
the s3c_gpio_cfgrange_nopull() wrapper.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change code setting special-function and no pull-up to use
the s3c_gpio_cfgrange_nopull() wrapper.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change code setting special-function and no pull-up to use
the s3c_gpio_cfgrange_nopull() wrapper.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A number of the SDHCI code configure a GPIO to a special function
and remove any pull-up, so add s3c_gpio_cfgrange_nopull() as a
wrapper to the s3c_gpio_cfgall_range() to make the code that
calls it fit on one line.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: Fix small comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a function to configure a range of GPIOs function and
pull in one go, mainly for the SDHCI and framebuffer helpers
which tend to do this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: Fix small comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting ranges of GPIO pins in mach-s5pv310 using
s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: coding-style fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: Fixed wrong change]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting ranges of GPIO pins in mach-s5p64x0 using
s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: modified to s5p64x0 from s5p6440]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: fixed wrong change]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To aide in changing the gpio code, remove the use of pin-specific configs
and move to using the S3C_GPIO_SFN() versions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add s3c_gpio_cfgpin_range() to configure a range of pins to the given
value. This is useful for a number of blocks where the pins are in order
and saves multiple calls to s3c_gpio_cfgpin().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the soc_camera
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FB_OMAP2 can work without VRFB, but currently does not build. Fix this.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Simplify conditional: (a || (!a && !b)) => (a || !b)
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Calls init functions of dss_features during dss_probe, and the following
features are made omapxxxx independent:
- number of managers, overlays
- supported color modes for each overlay
- supported displays for each manager
- global aplha, and restriction of global alpha for video1 pipeline
- The register field ranges : FIRHINC, FIRVINC, FIFOHIGHTHRESHOLD
FIFOLOWTHRESHOLD and FIFOSIZE
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
get_fbmem_region() is only called by omapfb_reserve_sdram_memblock() and
omapfb_reserve_sram() that both live in .init.text. So get_fbmem_region
can go there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This function is only called by omap_detect_sram which lives in .init.text,
too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
omap_init_fb() is only called as arch_initcall and so can live in
.init.text.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Commit ab69bcd66f (arm: remove
machine_desc.io_pg_offst and .phys_io) could not update
the new boards in the omap tree. This causes the build of
omap2plus_defconfig to fail. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Eric Miao <eric.miao at canonical.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP24xx, UART2 WKEN and WKST registers are in PM_WKEN2_CORE and
PM_WKST2_CORE respecitvely. Fix the OMAP2 register init to use the
correct registers on OMAP24xx.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes a warning
warning: (IMX_HAVE_PLATFORM_FLEXCAN && ARCH_MXC) selects HAVE_CAN_FLEXCAN which has unmet direct dependencies (NET && CAN)
(The warning in general exists since
246cf9c (kbuild: Warn on selecting symbols with unmet direct dependencies)
which was reverted between 71ebc01 and b1f7d6e.)
Reported-and-introduced-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
this patch gives the possibility to workaround bug ENGcm09152
on i.MX35 when the hardware workaround is also implemented on
the board.
It covers the workaround described on page 25 of the following Errata :
http://cache.freescale.com/files/dsp/doc/errata/IMX35CE.pdf
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It has USB phy built inside the IP itself.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts arm to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- ARM defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds support for termiox
Reviewed-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, only two operating points: 160Mhz and 800Mhz.
the operating points are tested on babbage 3.0
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
x86-64: Only set max_pfn_mapped to 512 MiB if we enter via head_64.S
xen: Cope with unmapped pages when initializing kernel pagetable
memblock, bootmem: Round pfn properly for memory and reserved regions
memblock: Annotate memblock functions with __init_memblock
memblock: Allow memblock_init to be called early
memblock/arm: Fix memblock_region_is_memory() typo
x86, memblock: Remove __memblock_x86_find_in_range_size()
memblock: Fix wraparound in find_region()
x86-32, memblock: Make add_highpages honor early reserved ranges
x86, memblock: Fix crashkernel allocation
arm, memblock: Fix the sparsemem build
memblock: Fix section mismatch warnings
powerpc, memblock: Fix memblock API change fallout
memblock, microblaze: Fix memblock API change fallout
x86: Remove old bootmem code
x86, memblock: Use memblock_memory_size()/memblock_free_memory_size() to get correct dma_reserve
x86: Remove not used early_res code
x86, memblock: Replace e820_/_early string with memblock_
x86: Use memblock to replace early_res
x86, memblock: Use memblock_debug to control debug message print out
...
Fix up trivial conflicts in arch/x86/kernel/setup.c and kernel/Makefile
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Olof Johansson <olof@lixom.net>
CC: Gary King <GKing@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Change-Id: Ibd0bcd46895eb88952b9db29e1f68572d39aae01
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Russell King <linux@arm.linux.org.uk>
CC: Gary King <GKing@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The APB DMA block handles DMA transfers to and from some peripherals
in the Tegra SOC. It reads from sequential addresses on the memory
bus, and writes repeatedly to the same address on the APB bus.
Two transfer modes are supported, oneshot for transferring a known
size to or from a peripheral, and continuous for streaming data.
In continuous mode, a callback occurs when the buffer is half full
to allow the existing data to be handled and a new request queued.x
v2 changes:
dma API no longer uses PTR_ERR
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Colin Cross <ccross@android.com>
Implement cpufreq support for the Tegra SOC. DVFS is handled by the
core virtual cpu clock. The frequencies of the two cores are tied
together, the highest frequency requested by either core determines
the actual frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- Add drivers to clock lookup table
- Add new pll_m entries
- Support I2C U16 divider
- Fix rate reporting on 32.768kHz clock
- Call propagate rate only if set_rate succeeds
- Add support for audio_sync clock
- Add 24MHz to PLLA frequency list
- Correct i2s1/2/spdifout mux
- Add suspend support
- Fix enable/disable parent clocks in set_parent
- Add max_rate parameter to all clocks
- DVFS support
- Add virtual cpu clock with dvfs
- Support clk_round_rate
- Fix requesting very high periph frequencies
- Add quirks for PLLU:
PLLU is slightly different from the rest of the PLLs. The
lock enable bit is at bit 22 instead of 18 in the MISC
register, and the post divider field is a single bit with
reversed values from other PLLs.
- Simplify recalculating clock rates
- Fix UART divider flags
- Remove unused clock ops
Signed-off-by: Colin Cross <ccross@android.com>
The Tegra SOC contains fuses to identify the CPU type and
bin, and a unique id. The CPU info is required to determine
the correct voltages for each cpu and core frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- the reset values for some pin groups in the tegra pin mux can result in
functional errors due to conflicting with actively-configured pin groups
muxing from the same controller. this change adds a known safe, non-
conflicting mux for every pin group, which can be used on platforms
where the pin group is not routed to any peripheral
- also add each pin group's I/O voltage rail, to enable platform code to
map from the pin groups used by each interface to the regulators used
for dynamic voltage control
- add routines to individually configure the tristate, pin mux and pull-
ups for a pingroup_config array, so that it is possible to program
individual values at run-time without modifying other values.
this allows driver power-management code to reprogram individual
interfaces into lower power states during idle / suspend, or to
reprogram the pin mux to support multiple physical busses per
internal controller (e.g., sharing a single I2C or SPI controller
across multiple pin groups)
- move chip-specific data like pingroups and drive-pingroups
out of the common code and into chip-specific code
- fix debug output for group with no pullups
- add a TEGRA_MUX_SAFE function. Setting a pingroup to TEGRA_MUX_SAFE
will automatically select a mux setting that is guaranteed not to
conflict with any of the hardware blocks.
Signed-off-by: Gary King <gking@nvidia.com>
mirror IRQ enable and disable operations on the legacy PPI system
interrupt controller, since the legacy controller is responsible
for responding to wakeup interrupts when the CPU is in LP2 idle mode
save the irq controller state on suspend and restore on resume
Signed-off-by: Gary King <gking@nvidia.com>
The "legacy irq controller" duplicates the functionality of the GIC,
but remains powered during the cpu suspend and idle modes that power
down the CPU and the GIC.
Signed-off-by: Colin Cross <ccross@android.com>
Add missing io address map entries from datasheet.
Add the IRAM area to the statically mapped io regions.
Correct the onewire, USB, and statmon addresses
Signed-off-by: Colin Cross <ccross@android.com>
Some boards that were added after the mass io_pgoffst/io_physio
removal, and were not updated in the original patch. Fixup here.
c.f. original io_pgoffst/io_physio removal
commit 6451d7783b
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
spi/bfin_spi: namespace local structs
spi/bfin_spi: init early
spi/bfin_spi: check per-transfer bits_per_word
spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
spi/bfin_spi: cs should be always low when a new transfer begins
spi/bfin_spi: fix typo in comment
spi/bfin_spi: reject unsupported SPI modes
spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
spi/bfin_spi: combine duplicate SPI_CTL read/write logic
spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
spi/bfin_spi: push all size checks into the transfer function
spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
spi/bfin_spi: sync hardware state before reprogramming everything
spi/bfin_spi: save/restore state when suspending/resuming
spi/bfin_spi: redo GPIO CS handling
Blackfin: SPI: expand SPI bitmasks
spi/bfin_spi: use the SPI namespaced bit names
spi/bfin_spi: drop extra memory we don't need
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
Commit c074512 (imx-esdhc: update devices registration) renamed
MX35_INT_MMC_SDHC2 to MX35_INT_ESDHC2 which broke expansion of the
MXC_INT_MMC_SDHC2 macro.
As (the only user of MXC_INT_MMC_SDHC2) is only used on
mx31 use the MX31 prefixed symbol to define its resources. Moreover to
reduce further confusion mxcsdhc_device0 is fixed accordingly and the MXC
prefixed symbols are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add required platform definitions for QT602240 touchscreen on I2C2 bus.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for si470x radio device on Samsung
Goni board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for S6E63M0 LCD controller on Samsung
Goni board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
[kgene.kim@samsung.com: fix build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds suspend-to-ram support for S5PV210.
Note. This patch is confirmed on SMDKV210 and SMDKC110 board.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error by S3C2410 PM Suspend debug option
due to undefined address.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung S5P SoCs have the same interrupt type defines for both
external interrupts and gpio interrupts. This patch removes all
duplicates from S5PC100 and S5PV210 specific includes as well as
gpio interrupt code and put a common defines to plat/irqs.h
NOTE: Do not use this for S5P6440 and S5P6450.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: add note for S5P64X0]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a common callback for gpio_to_irq() for external and
gpio interrupts for Samsung SoCs.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: moved samsung_gpiolib_to_irq() for s3c24xx build]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves external interrupt definitions from mach/gpio.h
to mach/regs-gpio.h for consistency with S5PV210.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PC100 SoC can use common S5P GPIO interrupt code. This patch
removes specific S5PC100 gpio interrupts code and adds required
defines and code to make use of common S5P code.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV210/S5PC110 can use common S5P GPIO interrupt code.
This patch adds required defines and code to make use of it.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds common code to enable support of GPIO interrupt on
S5P SoCs.
The total number of GPIO pins is quite large on S5P SoCs. Registering
irq support for all of them would be a resource waste. Because of that
the interrupt support for standard GPIO pins is registered dynamically
by the s5p_register_gpio_interrupt() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add the necessary definitions and mapping information to enable the
s3c-hsotg gadget to build.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for MMC power regulators on Samsung
Goni board. GPIO pin GONI_EXT_FLASH_EN has been transferred from machine
startup code to fixed voltage regulator.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for s3c-hsotg driver to enable usb
gadget support on Samsung Goni board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since commit 67a38950f0917aecfe1a3e46720d8bbb0020 there is no need
to set pixel clock for the s3c-fb driver's window information.
The correct pixel clock value can be automatically calculated from
the other screen parameters. This patch removes the redundant pixel clock
parameter.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the default upper_margin and vsync_len to get rid of repeated last
line on the display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
All the S5P series SoCs use the 'struct clksrc_clk' type to represent the
armclk. So the clk_arm clock instance available in the plat-s5p clock code
is not used in any of the S5P series SoCs.
This patch removes the unused clk_arm instance from plat-s5p clock code.
Reported-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes redundant selection PLAT_S5P in the CPU_S5P64XX config.
Because PLAT_S5P is selected if select ARCH_S5P64XX in the plat-s5p/Kconfig.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The selection PLAT_S5P is selected with plat-s5p/Kconfig.
So remove it form each CPU_S5PXXXX config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In case of S5PV310/S5PC210, it uses the SPARSEMEM as default memory
configuration. So moved to ARCH_S5PV310 config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In case of S5PV210/S5PC110, it uses the SPARSEMEM as default memory
configuration. So moved to ARCH_S5PV210 config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds to support Torbreck board of aESOP community using
Samsung S5PV210 SoC.
Signed-off-by: Kyuho Choi <chlrbgh0@gmail.com>
Signed-off-by: Hyunchul Ko <ghcstop@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The physical address of SYSCON(System Controller) is wrong.
This patch fixs this wrong physical address value from 0x10020000 to 0x10010000.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
It is reported by Junseok Jung that using clz instruction is
better instead of using for-loop to find the interrupt source.
This patch modifies interrupt source searching code using __ffs().
The __ffs() is implemented using clz instruction.
Suggested-by: Junseok Jung <jundols.jung@samsung.com>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support Watchdog Timer for S5PV310 and S5PC210.
Signed-off-by: Jemings Ko <jemings@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support RTC for S5PV310 and S5PC210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Jemings Ko <jemings@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMC(DRAM Memory Controller) map_desc table.
Because some driver such as CPUFREQ need to access DMC register.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support keypad device to the GONI board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes source clocks of moutcore.
That should be clk_mout_apll instead of clk_sclk_apll.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds various special clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds video clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds various clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds SDMMC clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds enable and ctrlbit for struct clksrc_clk clk_vpllsrc
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds log messages of aclk_200, aclk_100, aclk_160, and
aclk_133. And adds clk_p.rate from calculated aclk_100.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds struct clk clk_sclk_usbphy0, _usbphy1, and _hdmiphy
for adding member of clkset_group_list.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds 'clkset_aclk' to use commonly. And removed struct
clksrc_sources clkset_aclk_200, clkset_aclk_100, clkset_aclk_160,
and clkset_aclk_133.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds CPU hotplug support for S5PV310/S5PC210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates Kconfig of mach-s5pv310 for easily dividing S5PC210
and S5PV310 boards. S5PC210(MCP) machines and S5PV310 machines can be
build into one kernel, this will be provied/submitted when new defconfig
can be merged.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung SMDKC210 board support file. The SoC
of SMDKC210, S5PC210(MCP) is one of package option of S5PV310.
And because composition of SMDKC210 and SMDKV310 differs, need
SMDKC210 with SMDKV310.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add touchscreen device support for mach-mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for platform-lcd device for mach-mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for frame buffer device for mach-mini6410.
Patch also adds support for feature string parsing
for mini6410. The feature string is kernel command
line passed and currently lets select only LCD
configuration. At the moment there is support for
two LCD configurations - 4.3" and 7.0". Feature
parser is mach-mini2440 based.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add nand device support and mtd partition
table for mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for mini6410 board from FriendlyARM
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds suspend-to-ram support for SMDK2416 based on existing 2412 PM code
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 and S3C2416 has 12 GPIO banks (from A to M), increase
ARCH_NR_GPIOS for this architectures.
Also typo from previous commit has been fixed: CONFIG_CPU_S3C24XX
instead CONFIG_CPU_244X.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Since we can get both physical and virtual addresses from the addruart
macro, we can use this to establish the debug mappings.
In the case of CONFIG_DEBUG_ICEDCC, we don't need any mappings, but
may still need to setup r7 correctly.
Incorporating ASM changes from Nicolas Pitre <npitre@fluxnic.net>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
As mentioned in the comment right at the top, the first four fields
are directly accessed by assembly code in head.S. Move nr_irqs so the
comment is true again.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
It has been replaced with separate fields.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A bool will suffice. The default is little endian.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This does not seem to be implemented.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Defaults are "basic mode" for physical channels, and "logical source
logical destination" for logical channels.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
And keep it logical by default.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
And keep it low priority by default.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
without this patch we get :
arch/arm/mach-imx/built-in.o: In function `eukrea_cpuimx27_init':
eukrea_mbimx27-baseboard.c:(.init.text+0x44c): undefined reference to `mxc_ulpi_access_ops'
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
this patch fix the following errors :
arch/arm/mach-mx3/mach-pcm037_eet.c:62: error: implicit declaration of function 'MXC_SPI_CS'
arch/arm/mach-mx3/mach-pcm037_eet.c:185: error: implicit declaration of function 'imx35_add_spi_imx0'
from the Kconfig pcm037 is i.MX31 based and not i.MX35 so replace
imx35_add_spi_imx0 by imx31_add_spi_imx0
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: remove unneeded #include <mach/spi.h>]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is only a partial revert of "ARM: mx3/mx31ads: fold board
header in its only user"
[commit ccfa7c2698)]
As some of the the board defines are also used in the cs89x0
ethernet driver by the i.MX31 ADS.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the attached patch allows SD to work on i.MX51 with Wolfram's drivers
Tested on i.MX51.
Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Without this exiting WFI can result in cache corruption.
Code taken from Freescale's 2.6.27 BSP and tested on i.MX35
Signed-off-by: Eric Bénard <eric@eukrea.com>
this patch fix the following errors :
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_SDMA_BASE_ADDR’ undeclared here (not in a function)
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_INT_SDMA’ undeclared here (not in a function)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID
* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: Eric Bénard <eric@eukrea.com>
During the reorganisation of the imx-i2c devices
(in 64de5ec168) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.
Applies on 2.6.36-rc7
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add USB host device support for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add touchscreen device support for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add nand device support and mtd partition table
for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for frame buffer device for mach-real6410.
Patch also adds support for feature string parsing
for real6410. The feature string is kernel command
line passed and currently lets select only LCD
configuration. At the moment there is support for
two LCD configurations - 4.3" and 7.0". Feature
parser is mach-mini2440 based.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error about GPIO address due to
conflict of commit 4d914705 and 19a2c065.
- commit 4d914705: Fix on GPIO base addresses
- commit 19a2c065: Moves initial map for merging S5P64X0
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ various fixes ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1287036094.7768.291.camel@yhuang-dev>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
