Fix this sparse warnings:
drivers/net/e1000e/es2lan.c:1265:5: warning: symbol 'e1000_read_kmrn_reg_80003es2lan' was not declared. Should it be static?
drivers/net/e1000e/es2lan.c:1298:5: warning: symbol 'e1000_write_kmrn_reg_80003es2lan' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO support to e1000e by making it invoke napi_gro_receive
instead of netif_receive_skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a reset, releasing the swflag after it failed to be acquired would
cause a double unlock of the mutex. Instead, test whether acquisition of
the swflag was successful and if not, do not release the swflag. The reset
must still be done to bring the device to a quiescent state.
This resolves [BUG 12200] BUG: bad unlock balance detected! e1000e
http://bugzilla.kernel.org/show_bug.cgi?id=12200
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change interrupt vector naming to match recent changes from Robert Olsson.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return code for all NVM accesses[1] and error out accordingly; log
a debug message for failed accesses.
For ICH8/9, the valid NVM bank detect function was not checking whether the
SEC1VAL (sector 1 valid) bit in the EECD register was itself valid (bits 8
and 9 also have to be set). If invalid, it would have defaulted to the
possibly invalid bank 0. Instead, try to use the valid bank detection
method used by ICH10 which has been cleaned up a bit.
[1] - reads and updates only; not writes because those are only writing to
the Shadow RAM, the update following the write is the only thing actually
writing the modified Shadow RAM contents to the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82571 with SerDes, the true link state is not always correct when read
from the STATUS register; use existing e1000_has_link() function instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than reading the NVM to get the EEPROM version number everytime the
ethool get_drvinfo function is called, read it once during probe and save
it for future reference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing newline from debug message.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync flow control variables and usage model with that found in the ixgbe
driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link
is up before any traffic is sent; a new PHY operations function pointer is
provided for this. To facilitate read/write of the Kumeran registers
without blocking PHY register writes, the driver/firmware synchronization
method which previously used a hardware semaphore for both PHY and Kumeran
register accesses is now split. New Kumeran register read/write functions
utilize this new synchronization method.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return of pci_save_state and error out accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some branding strings (displayed via lspci) are missing from the comments in
various family-specific files in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for link test does not work properly for 82571 parts in a blade
environment with an unterminated serdes link partner. Make the test more
robust by checking the invalid bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the convention used elsewhere in e1000e to 'commit' PHY changes
instead of directly writing to the PHY CTRL register to reset it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been an issue seen with the pci-e quad port adapters that will
cause them to generate a pci-e correctable error on some system while
transitioning to D3.
Since no action is needed on this correctable error the simplest solution
is to mask off the reporting of correctable errors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables ECC correction for the packet buffer on all 82571
silicon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since e1000e has been existance in linux-2.6, we've
never released the hardware semaphore after a successful
write to the SPI EEPROM. I guess we don't write to
SPI EEPROM much -- but those few of us that do appreciate
it when we can later read from the EEPROM without having
to reboot.
Found-by: Nick Van Fossen <Nick.VanFossen@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Reviewed-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing 'WARN_ON(preempt_count())' was horribly horribly wrong, and would
cause tons of warnings at bootup if PREEMPT was enabled because the
initcalls currently run with the kernel lock, which increments the
preempt count.
At the same time, the warning was also insufficient, since it didn't
check that interrupts were enabled.
The proper debug function to use for something that can sleep and wants
a warning if it's called in the wrong context is 'might_sleep()'.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a mutex to the e1000e driver that would help
catch any collisions of two e1000e threads accessing hardware
at the same time.
description and patch updated by Jesse
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the stats lock is left over from e1000, e1000e no longer
has the adjust tbi stats function that required the addition
of the stats lock to begin with.
adding a mutex to acquire_swflag helped catch this one too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
thanks to tglx, we're finding some interesting reentrancy issues.
this patch removes the phy read from inside a spinlock, paving
the way for removing the spinlock completely. The phy read was
only feeding a statistic that wasn't used.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
e1000e was apparently calling two functions that attempted to reserve
the SWFLAG bit for exclusive (to hardware and firmware) access to
the PHY and NVM (aka eeprom). These accesses could possibly call
msleep to wait for the resource which is not allowed from interrupt
context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in the process of debugging things, noticed that the swflag is not reset
by the driver after reset, and the swflag is probably not reset unless
management firmware clears it after 100ms.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM. This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: arjan@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With 2.6.27-rc3 I noticed the following messages in my boot log:
0000:01:00.0: 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:04:ff:09
The second seems correct, but the first has a silly repetition of the
PCI device before the actual message. The message originates from
e1000_eeprom_checks in e1000e/netdev.c.
With this patch below the first message becomes
e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
which makes it similar to directly preceding messages.
Use dev_warn instead of e_warn in e1000_eeprom_checks() as the interface
name has not yet been assigned at that point.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the driver fails to acquire the control flag used to serialize
NVM and PHY accesses between the driver, firmware and hardware, remove the
request for the flag otherwise the hardware might grant the flag when it
becomes available but the driver will not release the flag. This could
cause the firmware to prevent the driver getting the flag for all future
attempts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This new part has the same feature set as previous parts with the addition
of MSI-X support.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for new LOM devices on the latest generation ICHx platforms.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable PCI device ID for a new combination of MAC and PHY already supported
in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The removal of this bit of code was missed in an earlier patch submittal.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some systems do not like 82571/2 use of 16-bit MSI messages and some
other systems claim to support MSI, but neither really works. Setup a
test MSI handler to detect whether or not MSI is working properly, and
if not, fallback to legacy INTx interrupts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Setting an MTU value below 68 was disabling the network connection and
would not reconnect until the driver was reloaded. Prevent changing the
MTU to anything below 68.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prevent Tx hangs from happening on 10Mb flood ping by increasing the
timeout factor.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
