airo_cs is broken on m32r; marked as such. [Proper fix would involve
separating PCI-dependent parts and making sure they don't get in the
way _and_ arranging for asm/scatterlist.h getting picked on m32r]
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ISA parts of tms380tr are using ISA DMA helpers and should depend on
ISA_DMA_API.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A problem was reported by Grant Grundler on an HP rx8620 using IOX
Core LAN partno(A7109-6) 5701 copper NIC. The tg3 driver mistakenly
detects this NIC as having a SerDes PHY and link does not come up as a
result.
The problem was caused by an incorrectly programmed eeprom that set the
NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit in the NIC_SRAM_DATA_CFG location.
This patch will override the NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit if a
valid PHY ID is read from the MII registers on older 570x chips where
the MII interface is not used on SerDes chips. On newer chips such as
the 5780 that use MII for both copper and SerDes, SerDes detection must
rely on the eeprom.
This patch will make the SerDes detection identical to versions 3.25 and
older.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000 driver is responding to ioctl() calls it should not be. This
can cause problems with the wireless tools incorrectly indentifying the
device as wireless capable, and crashing under certain operations.
This patch also moves the version printk() to the init call, so that
you only get it once for multiple devices, and to show it is loaded
if there are no defined dm9000s
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix DM9000 driver usage of spinlocks, which mainly came to light
when running a kernel with spinlock debugging. These come down to:
1) Un-initialised spin lock
2) Several cases of using spin_xxx(lock) and not spin_xxx(&lock)
3) move the locking around the phy reg for read/write to only
keep the lock when actually reading or writing to the phy.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After suspend the driver needs to retest link status in case the cable
has been inserted or removed during the suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Using the right register clearly improves chances of getting the MII
code and thus the driver working at all.
- On startup check the media type before setting up duplex or we might
spend the first 1.2s with a wrong duplex setting.
- Get rid of whitespace lines.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Suggested by Steven Rostedt, matches his patch included in e100.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the p-persistence CSMA algorithm which in simplex mode was starting
with a slottime delay before doing anything else as if there was carrier
collision resulting in bad performance on simplex links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Else on SMP systems it is possible for hotplug to execute,
invoke tg3_open(), and end up loading the uninitialized
PCI register save area into the card.
Signed-off-by: David S. Miller <davem@davemloft.net>
cs89x0 talks a lot at boot. Seems like debug leftover. This patch
downgrades printks to KERN_DEBUG. While we're at it, make these messages a
bit less obscure.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it compile with CONFIG_PM=n
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers really only work well in SMP if they actually can be selected.
This is a leftover from the time when the 6pack drive only used to be
a bitrotten variant of the slip driver.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Kconfig | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Hi Jeff,
Here's a little patch fixing a typo in smc91x.h.
Regards,
Tony
--ReaqsoxgOBHFXBhH
Content-Type: text/x-chdr; charset=us-ascii
Content-Disposition: inline; filename="patch-fix-typo-smc91x.h"
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Yukon-Lite chipset needs workaround for revision 7 (or later).
Without this patch, chip gets stuck in low power mode and never
boots. Newer SysKonnect vendor code already had same patch.
Related bug in skge is http://bugs.gentoo.org/87822
Chris, please add for 2.6.12.2
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.
Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
An early version of the sk98lin patch was merged via Len's tree. But there
were subsequent updates as a result of review from Jeff. THis fixes things
up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].
(akpm: we need to fast-track this. It's causing ia64 to oops on shutdown)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicates from the device id table.
Signed-off-by: Jarkko Raja <jar@pcuf.fi>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move in_aton to allow netpoll and pktgen to work without the rest of
the IPv4 stack. Fix whitespace and add comment for the odd placement.
Delete now-empty net/ipv4/utils.c
Re-enable netpoll/netconsole without CONFIG_INET
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggestion from Sam Ravnborg <sam@ravnborg.org>
It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
token ring, wireless, PCMCIA, WAN, ATM, and S390.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780S support by adding a new tg3_setup_fiber_mii_phy() function and
a timer function for parallel link detection. 5780S uses standard MII
registers for 1000BaseX and runs in GMII mode as opposed to TBI mode on
older serdes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disallow jumbo TSO on 5780 due to hardware restrictions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all DMA watermark settings for standard and jumbo frames on
all chips in tg3_init_bufmgr_config() and add new settings for 5780.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rx_pkt_buf_sz to the tg3 structure to support variable buffer
sizes on the standard ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic jumbo frames support for 5780. This chip supports jumbo frames
on the standard receive ring without the jumbo ring. The
TG3_FLAG_JUMBO_ENABLE is changed to TG3_FLAG_JUMBO_RING_ENABLE to
indicate using the jumbo ring on 5704 and older chips. A new
TG3_FLG2_JUMBO_CAPABLE flag is added to indicate jumbo frames support
with or without the jumbo ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780 PCI IDs, chip IDs, and other basic support.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
