PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch). This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired. The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.
The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed. However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers). This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset. If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect. Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fd8235bb overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to have been a mixup in the max supported jumbo frame size
between 82574 and 82583 which ended up disabling jumbo frames on the 82574
as a result. This patch swaps the two so that this issue is resolved.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer
support for e1000e, but it is not reasonable to disable it in
e1000_remove but enable it in e1000_resume. This patch enables aer
support in e1000_probe.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get
configured on newer parts which use PHY wakeup vs. MAC wakeup which causes
WoL to not work. The driver should configure PHY wakeup whether or not
manageability is enabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bank offset was being incorrectly calculated on ICH9 parts with a bank
size of 8K (instead of the more common 4K bank) which would cause any NVM
writes to be done on the wrong address after switching from bank 1 to bank
0. Additionally, assume we are meant to use bank 0 if a valid bank is not
detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore
when writing to the shadow ram version of the NVM image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to
acquire the SW/FW/HW semaphore instead of multiple times to prevent the
hardware from having problems (especially for systems with manageability
enabled), and extend the timeout for the hardware to set the SWFLAG bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets. Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs may require two reads of the PHY_STATUS register to determine the
link status. If the PHY is being accessed by another thread it is possible
the first read could timeout and fail. In this case, put a delay in so
the second read will pick up the correct link status.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was accessing register bits for features on parts that do
not support that feature. This could cause problems in the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently. Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing. Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround. Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
on permanent failure
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure. This state is not
checked in many of the network drivers.
This patch fixes the omission in the e1000e driver.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last hunk of this commit:
commit 12d04a3c12
Author: Alexander Duyck <alexander.h.duyck@intel.com>
Date: Wed Mar 25 22:05:03 2009 +0000
e1000e: commonize tx cleanup routine to match e1000 & igb
changed the logic for determining if we should call napi_complete or
not at then end of a napi poll.
If the NIC is using MSI-X with no work to do in ->poll, net_rx_action
can just spin indefinitely on older kernels and for 2 jiffies on newer
kernels since napi_complete is never called and budget isn't
decremented.
Discovered and verified while testing driver backport to an older
kernel.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool is a standard way of getting information about
ethernet interfaces. We enhance ethtool kernel interface
& e1000e to make the MDI-X status readable via ethtool in
userspace.
Signed-off-by: Chaitanya Lala <clala@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_config_collision_dist() sets tctl, but subsequently tctl is
overwritten. It seems to me that as things stand the call to
e1000e_config_collision_dist() has no effect and should either be
removed or moved down a little bit. This kernel patch takes the latter
option.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With bi-directional stress traffic, the receiver could hang causing the
hardware to stop and a "Detected Tx Unit Hang" message dumped to the system
logfile. Temporarily workaround this issue by disabling Tx flow control by
default. The issue is currently being investigated and a follow-on patch
will be provided to revert this when it is resolved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters. These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions). New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting the maximum frame size supported by the hardware into the
adapter structure, the change_mtu entry point function can be cleaned
up of checks for all the different max frame sizes supported by
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown. Check for
support before attempting to disable the feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy port status register has the MDI-X status bit on bit 11, not bit 3
as is currently setup in the define. This patch corrects that so the
correct bit is checked on igp PHY types.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down. Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.
Don't bother arming to tx hang detection when link is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Andy tested this for e1000e and confirmed it was working for him.
see thread: http://marc.info/?l=linux-netdev&m=123946479705636&w=2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andy Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000e transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000e from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000e_shutdown() from e1000e_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000/e1000e compile report a possible unused variable, fix
that for now. Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
