Use dsi_enable_scp_clk and dsi_disable_scp_clk in CIO init and uninit,
and improve the CIO init by adding a few status checks and error
handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
SCP clock is needed for CIO on OMAP3, and for CIO and PLL on OMAP4.
Current driver enables the CIO clock always when DSI display is
initialized. However, if a DPI display tries to use DSI PLL, the SCP
clock is never enabled.
This patch implements simple ref counting enable/disable functions for
SCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP3430 has RESETDONETXCLKESCx bits in the order following bitnumber
order for lanes 0, 1, 2: 28, 27, 26. OMAP3630 and later have them in
saner order: 24, 25, 26 (and 27, 28 for OMAP4).
This patch adds a dss_feature that can be used to differentiate between
those two orders of RESETDONETXCLKESCx bits.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename ComplexIO from dsi_complexio_xxx to dsi_cio_xxx for brevity.
Also, add cio prefix for couple of functions that didn't have it, but
are cio related.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI pins are powered by VDDS_DSI. If VDDS_DSI is off, the DSI pins
are floating even if they are pinmuxed to, say, safe mode and there's a
pull down/up.
This patch gives the panel drivers an option to leave the VDDS_DSI power
enabled while the DSS itself is turned off. This can be used to keep the
DSI lanes in a valid state while DSS is off, if the DSI pins are muxed
for pull down (not done in this patch).
There will be a slight power consumption increase (~100 uA?) when the
VDDS_DSI is left on, but because this option is used when the panel is
left on, the regulator consumption is negligible compared to panel power
consumption.
When the panel is fully turned off the VDDS_DSI is also turned off.
As an added bonus this will give us faster start up time when starting
up the DSS and the regulator is already enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Entering ULPS (Ultra Low Power State) happens by sending ULPS entry
sequence to the DSI peripheral and pulling the DSI lines down.
Exiting ULPS happens by sending ULPS exit sequence.
We can send the ULPS entry sequence by using OMAP DSS HW's ULPS support,
but we cannot use the ULPS exit support from DSS HW. DSS HW refuses to
send the ULPS exit sequence if it thinks that the lanes are not in ULPS.
After being in OFF mode the DSS HW has been reset, and so it does not
know that the lanes are actually in ULPS.
Thus we need to use the lane override support and manually send the ULPS
exit sequence. Luckily the sequence is very simple.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CIO LDO status check seems to be broken on OMAP3630+ chips, and it's
also quite unclear what LDO status actually tells and when its status
changes.
This patch removes the whole check on the grounds that if there's a
problem with the LDO, we should anyway catch the problem as we check the
CIO power state and CIO reset status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI_DSIPHY_CFG10 register can be used to override DSI lane state. Add
functions to configure and enable the override, and to disable the
override.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4 has clocks set up in a bit interesting way, causing, for example,
the DSS's "ick" to be called "dss_fck".
This patch changes the debugfs output to show both the DSS's name for
the clock (ie. basically the clock alias), and the real name from the
clock struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Convert simple/strict_strto* functions to kstrto* functions. Only simple
cases are converted.
simple_strto* uses are still left to places where it is used to parse
numbers from a list of numbers. These need some other solution than
kstrto*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock sources for DISPC_FCLK and LCD1_CLK are now specified in the board file.
There is no need for the hack config "CONFIG_OMAP2_DSS_USE_DSI_PLL" anymore.
Introduce function dpi_use_dsi_pll() which checks for the clock sources to decide
whether DSI PLL is to be used or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add enum dss_clock_source in dssdev.clocks struct so that the clock sources can
be specified in the board file.
Replace hard coded clock sources in dsi.c, dpi.c and replace them with the new
clock source members in dssdev.clocks. Modify the sdp4430_lcd_device struct in
board-4430sdp.c to specify clock sources for DISPC_FCLK, LCD1_CLK and DSI1_FCLK.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can use __exit for the driver remove function in plain dss panels
(ie. those that do not need i2c or spi).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_register_device and omap_dss_unregister_device can only be
called from core.c, so we can make it static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
VENC code was missing omap_dss_start/stop_device calls. This didn't
cause any problems as VENC could not be compiled as a module, but
nevertheless it's better to add the calls.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapfb does an implicit display update (for manual update
displays) on unblank.
There is no guarantee that the framebuffer contains a valid image when
unblank is called. When using manual update displays it is the
responsibility of the user space to update the display, and so it should
be in this case also.
This patch removes the implicit display update on unblank.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
[tomi.valkeinen@ti.com: improved description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Errors from the panel driver were ignored during panel initialization.
Handle the errors and fail accordingly.
Also move the display initialization to a separate function to make it
cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add get_dimensions() to struct omap_dss_driver. Use the call, if supported
by the driver, in OMAPFB.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
VENC code had 50ms sleep after enabling the output and 100ms sleep after
disabling the output. I don't see any reason for these sleeps.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's a 20ms sleep after VENC reset. It's unknown what bug this
circumvents and on what platforms. Add a Kconfig option to disable the
sleep.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some unknown reason we may get SYNC_LOST errors from the display
subsystem at initialization time if we don't sleep before resetting the
DSS. See the source (dss.c) for more comments.
However, 50ms is quite long time to sleep, and with some configurations
the SYNC_LOST may never happen, so this patch creates a Kconfig option
to disable the sleep.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sleep workaround for the problem described in the comment doesn't
really work. This patch removes the workaround, and improves the comment
about the bug, and proposes an userspace workaround.
omap_dss_set_manager() is called 6 times when loading omapdss and
omapfb, which means that 40ms * 6 = 240ms was spent sleeping when
booting up.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock configuration was defined inside dssdev.phy.dsi struct. The clock
config doesn't really belong there, and so it's moved to dssdev.clock
struct.
Now the explicit clock configuration could also be used for other
interfaces than DSI, although there's no support for it currently.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI protocol engine has no interrupt for signalling the end of a Frame
transfer. The present approach is to send a BTA after DISPC generates a
FRAMEDONE interrupt, and unlock the dsi bus only when the BTA Ack is received.
The assumption made with this approach was that OMAP will send a BTA only after
the long packet corresponding to the last line is sent. However, it is possible
that on the DISPC FRAMEDONE interrupt there are 2 (or more) lines of pixel data
in the DSI line buffer. Hence, the BTA Ack could be received for the long packet
corresponding to the second last line (or the third last and so on..).
Therefore, the current method doesn't ensure that the complete frame data is
sent before we start a new transfer. A similar explanation holds valid if we
send a BTA in between multiple short/long command packets from the slave port.
Introduce dsi_sync_vc functions, based on Tomi Valkeinen's idea, which ensure
that the DSI Virtual Channel in use(update_channel) completes its previous work
before proceeding to the next Frame/Command.
For a frame update, the DSI driver now sends a callback to the Panel Driver
on the FRAMEDONE interrupt itself. The callback in the panel driver then unlocks
the bus. dsi_sync_vc() functions are placed in dsi_vc_config_l4() and
dsi_vc_config_vp() to ensure that the previous task of the Virtual Channel is
completed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The following changes have changed from OMAP3 to OMAP4 DSI:
-The register field DSI_PLL_FREQSEL in DSI_PLL_CONFIGURATION2 has been removed.
-DCS_CMD_ENABLE and DCS_CMD_CODE bits have been moved from DSI_CTRL to
DSI_VC_CTRLi, hence the control of the bits is available per VC.
-DSI LDO powergood notification doesn't work on OMAP4. This is mentioned in
OMAP4 errata revision 1.8(Errata 1.76).
-OCP_WIDTH register field is included in DSI_VC_CTRL.
-The SCP clock is also required to access DSI PLL registers
Introduce dss features for these changes so that DSI runs on both OMAP3 and
OMAP4.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP3630 has a HW bug causing DSI PLL power command POWER_ON_DIV (0x3)
to not work properly. The bug prevents us from enabling DSI PLL power
only to HS divider block.
This patch adds a dss feature for the bug and converts POWER_ON_DIV
requests to POWER_ON_ALL (0x2).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.lcd_clk_source is set to the default value DSS_CLK_SRC_FCK at dss_init.
For OMAP2 and OMAP3, the dss.lcd_clk_source should always be the same as
dss.dispc_clk_source. The function dss_get_lcd_clk_source() always returns the
default value DSS_CLK_SRC_FCK for OMAP2/3. This leads to wrong clock dumps when
dispc_clk_source is not DSS_CLK_SRC_FCK.
Correct this function to always return dss.dispc_clk_source for OMAP2/3.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP4, reading DSI_PLL_CONFIGURATION2 register requires the L3 clock
(CIO_CLK_ICG) to PLL. Currently dsi_dump_clocks() tries to read that
register without enabling the L3 clock, leading to crash if DSI is not
in use.
The status of the bit being read from DSI_PLL_CONFIGURATION2 is
available from dsi_clock_info->use_sys_clk, so we can avoid the whole
problem by just using that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
use_sys_clk and highfreq fields in dsi.current_cinfo were never set.
Luckily they weren't used anywhere so it didn't cause any problems.
This patch fixes those fields and they are now set at the same time as
the rest of the fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the
OMAP DSS panel driver for Nokia's DSI displays. A more logical place for
it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There may be multiple ways of controlling the backlight on a given
machine. Allow drivers to expose the type of interface they are
providing, making it possible for userspace to make appropriate policy
decisions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add dss.dpll4_m4_ck (DSS FCLK) initialization for OMAP4. This is used
to compute the pixel clock for DPI interface and also to reconfigure
the DSS FCLK to the desired rate, corresponding to the rate computed
for pixel clock.
Adding these cpu_is_44xx() checks are meant to be temporary, until a
cleaner implementation to manage these checks are added. Currently this
is needed to get DVI display running on OMAP4 PandaBoard
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: minor changes due to conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2 does not have dpll4_m4_ck source clock for dss functional clock,
but later OMAPs do. Currently we check for cpu type in multiple places
to find out if dpll4_m4_ck is available.
This patch cleans up dss.c by using the fact that dss.dpll4_m4_ck
pointer is NULL on OMAP2. This allows us to remove many of the cpu
checks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
calling the platform registration of HDMI driver from core
during initialization.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding kconfig and makefile changes to add support for HDMI in OMAP4.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The panel driver(hdmi_omap4_panel.c) in omap2/dss acts as a controller
to manage the enable and disable requests and synchronize audio and video.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding the hdmi interface driver(hdmi.c) to the dss driver. It configures
the audio and video portion of HDMI based on functionality called by the
panel driver.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Yong Zhi <y-zhi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding the hdmi interface driver header file (hdmi.h) to the dss driver.
Register and structure declaration done here.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding function to reset/set gamma table bit for TV interface, currently
only support for disabled is added.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding function to select between HDMI or VENC clock source.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding display type HDMI in dss_features, overlay and the manager so that
HDMI type of display will be recognized.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
print_irq_status functions can be called with empty irq status when full
irq debugging is enabled. This patch makes print_irq_status functions
return immediately when given an empty irq status to lessen the debug
spam slightly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_vc_send_bta_sync() waits for BTA interrupt with a 500ms timeout. If
a DSI error happens, no BTA is received and the timeout triggers. This
could be handled much faster by listening to DSI errors also.
This patch uses the ISR support to notice DSI errors while waiting for
the BTA, thus speeding up the fail-path considerably.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add generic ISR support for DSI interrupts. ISRs can be used instead of
custom hooks in the interrupt handler.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up the IRQ handler a bit by separating collection of IRQ stats and
handling of IRQ errors to separate functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI PLL parameters (regm, regn, regm_dispc, regm_dsi, fint) have different
fields and also different Max values on OMAP3 and OMAP4. Use dss features to
calculate the register fields and min/max values based on current OMAP revision.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create 2 functions dss_feat_get_param_min() and dss_feat_get_param_max() which
return the minimum and maximum value of a parameter. Introduce a enum in
dss_features called dss_range_param which contains parameters whose ranges we
are interested in.
Replace this with dss_feat_get_max_dss_fck() which is specific to the parameter
DSS_FCK.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The structures dss_reg_field and dss_clk_source_name have enum members which
specify the register field and the clock source respectively. These members are
not used to choose the correct result in the corresponding feature functions.
Remove these members and change the features array declaration to incorporate
these enums.
The structure dss_clk_source_name without the enum member is just a pointer to
an string. Remove the structure and use a character pointer directly.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Something seems to be wrong with OMAP4 & VENC, and register access fails
in omap_venchw_probe().
This patch skips venc driver registration on OMAP4, thus circumventing
the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, the pixel clock for the LCD manager was derived through DISPC_FCLK as:
Lcd Pixel clock = DISPC_FCLK / lcd / pcd
Where lcd and pcd are divisors in the DISPC_DIVISOR register.
On OMAP4, the pixel clocks for LCD1 and LCD2 managers are derived from 2 new
clocks named LCD1_CLK and LCD2_CLK. The pixel clocks are calculated as:
Lcd_o Pixel clock = LCDo_CLK / lcdo /pcdo, o = 1, 2
Where lcdo and pcdo registers are divisors in DISPC_DIVISORo registers.
LCD1_CLK and LCD2_CLK can have DSS_FCLK, and the M4 divider clocks of DSI1 PLL
and DSI2 PLL as clock sources respectively. Introduce functions to select and
get the clock source for these new clocks. Modify DISPC functions get the
correct lck and pck rates based on the clock source of these clocks. Since
OMAP2/3 don't have these clocks, force OMAP2/3 to always have the LCD_CLK source
as DSS_CLK_SRC_FCK by introducing a dss feature.
Introduce clock source names for OMAP4 and some register field changes in
DSS_CTRL on OMAP4.
Currently, LCD2_CLK can only have DSS_FCLK as its clock source as DSI2 PLL
functionality hasn't been introduced yet. BUG for now if DSI2 PLL is selected as
clock.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up some of the DSS functions which select/get clock sources, use switch
to select the clock source members since more clock sources will be introduced
later on.
Remove the use of macro CONFIG_OMAP2_DSS_DSI in dispc_fclk_rate, use a dummy
inline for function for dsi_get_pll_hsdiv_dispc_rate() instead for code clarity.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the Gumstix Palo35 expansion board
which utilizes the 320 x 240 pixel LG.Philips LB035Q02 LCD Panel
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix handling of error in omap_dispc_register_isr() in case there are no
free isr slots available.
Reported-by: Ben Tucker <btucker@mpcdata.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Using dss_features to select independent core clock divider and setting
it. Added the register used, to DISPC context save and restore group
-----------------------------------------------------------------------
In OMAP4, the minimum DISPC_CORE_CLK required can be expressed as:
DISPC_CORE_CLK >= max(PCLK1*HSCALE1, PCLK2*HSCALE2, ...)
Where PCLKi is the pixel clock generated by MANAGERi and HSCALEi is the
maximum horizontal downscaling done through MANAGERi
Based on the usecase, core clk can be increased or decreased at runtime
to save power. Such mechanism are not yet implemented. Hence, we set the
core clock divisor to 1, to support maximum range of resolutions
------------------------------------------------------------------------
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP4 DISPC_DIVISOR1 is backward compatible to OMAP3xxx DISPC_DIVISOR.
However DISPC_DIVISOR is also provided in OMAP4, to control DISPC_CORE_CLK
independent of Primary and Secondary display clocks.
Renamed DISPC_DIVISOR(ch) to DISPC_DIVISORo(ch), to facilitate introduction
of DISPC_DIVISOR register, which is specific for OMAP4. OMAP4 has 3 registers
DISPC_DIVISOR, DISPC_DIVISOR1 and DISPC_DIVISOR2.
Also updated, all the usages of DISPC_DIVISOR(ch) to DISPC_DIVISORo(ch).
Use DISPC_DIVISORo(ch) when DISPC_DIVISOR1 or DISPC_DIVISOR2 has to be
configured
OMAP4 TRM uses DISPC_DIVISORo generically to refer to DISPC_DIVISOR1 and
DISPC_DIVISOR2
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3xxx DISPC_DIVISOR register has a logical clock divisor (lcd_div)
field. The lcd_div is common, for deciding the DISPC core functional clock
frequency, and the final pixel clock frequency for LCD display.
In OMAP4, there are 2 LCD channels, hence two divisor registers, DISPC_DIVISOR1
and DISPC_DIVISOR2. Also, there is a third register DISPC_DIVISOR.
The DISPC_DIVISOR in OMAP4 is used to configure lcd_div exclusively for core
functional clock configuration. For pixel clock configuration of primary and
secondary LCDs, lcd_div of DISPC_DIVISOR1 and DISPC_DIVISOR2 are used
respectively
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On omap4 the registers may not be accessible right after enabling the
clocks. At some point this will be handled by pm_runtime, but, for the
time begin, adding a small delay after clk_enable() should make things
work.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When using OMAP2_DSS_USE_DSI_PLL, which selects DSI PLL as source clock
for DISPC, the DSI needs the vdds_dsi regulator. Latest regulator
changes broke this, causing the the code to not acquire the regulator
when using OMAP2_DSS_USE_DSI_PLL.
This patch acquires the vdds_dsi regulator in dsi_pll_init(), fixing the
issue. This is is just a quick hack to get the OMAP2_DSS_USE_DSI_PLL
option working. There shouldn't be any other downside in this solution
than some extra lines of code.
OMAP2_DSS_USE_DSI_PLL is itself a big hack, and should be removed, and
the feature itself should be implemented in a more sane way. However,
the solution is not trivial, and people are using DSI PLL to get more
exact pixel clocks, so this hack is an acceptable temporary solution for
the time being.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Taal driver used to take a hard coded Macro for Virtual Channel and the VC_ID.
The Taal panel driver now requests for a Virtual channel through the
omap_dsi_request_vc() call in taal_probe().
The channel number returned by the request_vc() call is used for sending command
and data to the Panel. The DSI driver automatically configures the Virtual
Channel's source to either Video Port or L4 Slave port based on what the panel
driver is using it for.
The driver uses omap_dsi_release_vc() to free the VC specified by the panel.
taal_remove() or when a request_vc() call fails.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce functions which request and release VC's. This will be used in panel
drivers in their probes.
omap_dsi_request_vc() takes in the pointer to the omap_dss_device, the VC_ID
parameter which goes into the header of the DSI packets, and returns a Virtual
channel number (or virtual channel register set) which it can use.
omap_dsi_set_vc_id() takes the omap_dss_device pointer, the Virtual Channel
number and the VC_ID that needs to be set for the specifed Virtual Channel.
omap_dsi_release_vc() takes the omap_dss_device pointer and the Virtual Channel
number that needs to be made free.
Initialisation of VC parameters is done in dsi_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
cpu_is_omapxxx() was used previously to select the supported interfaces.
Now that the interfaces are platform devices, we no longer need to do
the check when registering the driver. Thus we can just remove the
checks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI and SDI are different from the other interfaces as they are not
hwmods and there is not platform driver for them. They could be said to
be a part of DSS or DISPC modules, although it's not a clear definition.
This patch moves DPI and SDI initialization into DSS platform driver,
making the code more consistent: omap_dss_probe() only initializes
platform drivers now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
FB_OMAP_BOOTLOADER_INIT does not work, and it was only partially
implemented for SDI.
This patch removes support for FB_OMAP_BOOTLOADER_INIT to clean up the
code and to remove any assumptions that FB_OMAP_BOOTLOADER_INIT would
work.
Proper implementation is much more complex, requiring early boot time
register and clock handling to keep the DSS running.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI PLL output clock names have been made more generic. The clock name
describes what the source of the clock and what clock is used for. Some of
DSI PLL parameters like dividers and DSI PLL source have also been made more
generic.
dsi1_pll_fclk and dsi2_pll_fclk have been changed as dsi_pll_hsdiv_dispc_clk
and dsi_pll_hsdiv_dsi_clk respectively. Also, the hsdividers are now named
regm_dispc and regm_dsi instead of regm3 and regm4.
Functions and macros named on the basis of these clock names have also been
made generic.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock source names vary across OMAP2/3 and OMAP4, the clock source enum
names have been made generic in the driver, but for purposes of debugging
and dumping clock sources, it is better to preserve the actual TRM name of
the clock.
Introduce a dss feature function 'dss_feat_get_clk_source_name()' which
returns a string with the TRM clock name for the current OMAP in use. The OMAP
specific name is printed along the generic name within brackets.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The enum members of 'dss_clk_source' have clock source names specific to
OMAP2/3. Change the names to more generic terms such that they now describe
where the clocks come from and what they are used for.
Also, change the enum member names to have "DSS_CLK_SRC" instead of "DSS_SRC"
for more clarity.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The maximum supported frequency for DSS has increased from 173 to 186 Mhz on
OMAP4.
Introduce a dss feature function to get the max_fck to replace DISPC_MAX_FCK
macro.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_features and register fields to incorporate changes in DISPC pipelines
between OMAP3 and OMAP4.
Register fields added: FEAT_REG_HORIZONTALACCU, FEAT_REG_VERTICALACCU
DSS Features added: FEAT_LINEBUFFERSPLIT, FEAT_ROWREPEATENABLE, FEAT_RESIZECONF
_dispc_set_scaling() and _dispc_set_rotation_attrs() have been cleaned up.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hwmod databases provide information about which optional clocks are available
for a given platform. This is available via a function pointer opt_clock_enable
in pdata.
Use this information during get/enable/disable/put of clocks.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_reset_tx_fifo() was not used. Furthermore, OMAP errata states that
TX FIFO flush is not functional, so the function wouldn't even have
worked.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Only OMAP 3430 hardware has SDI support. The availability of SDI HW can
be found out by checking if the LCD channel supports SDI displays.
This patch checks for SDI HW support before accessing SDI registers,
which fixes a crash on OMAP4 when SDI SW support is compiled in.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP 3630 does not support SDI. Split omap3_dss_supported_displays into
3430 and 3630 entries, and remove the SDI from 3630 entry.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Support for the display interface was checked in a separate switch-case.
There's no reason for that, and this patch handles the fail code path in
the same switch-case where the display initialization is done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, the core DSS platform device requests for an irq line for OMAP2 and
OMAP3. Make DISPC and DSI platform devices request for a shared IRQ line.
On OMAP3, the logical OR of DSI and DISPC interrupt lines goes to the MPU. There
is a register DSS_IRQSTATUS which tells if the interrupt came from DISPC or DSI.
On OMAP2, there is no DSI, only DISPC interrupts goto the MPU. There is no
DSS_IRQSTATUS register.
Hence, it makes more sense to have separate irq handlers corresponding to the
DSS sub modules instead of having a common handler.
Since on OMAP3 the logical OR of the lines goes to MPU, the irq line is shared
among the IRQ handlers.
The hwmod irq info has been removed for DSS to DISPC and DSI for OMAP2 and OMAP3
hwmod databases. The Probes of DISPC and DSI now request for irq handlers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb.mode is passed through bootargs, when omapfb is setting mode,
it would check if timings passed are fine for panel attached to it.
It makes use of check_timing API provided by the panel.
In current code if check_timing API is not available for attached panel,
OMAPFB would return -EINVAL and BPP sent via bootargs will not have any effect.
In case of panels like TAAL panel, omapfb or any other driver should not be allowed to
change the timings. So bpps sent via bootargs will not have an effect.
In such case we can check only the x_res and y_res with the panels resolution
and if they match go ahead and set the bpps.
The bpp value sent via bootarg would have an effect.
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS submodules DPI/SDI/DSI/VENC require a regulator to function.
However, if the board doesn't use, say, SDI, the board shouldn't need to
configure vdds_sdi regulator required by the SDI module.
Currently the regulators are acquired when the DSS driver is loaded.
This means that if the kernel is configured with SDI, vdds_sdi regulator
is needed for all boards.
This patch changes the DSS driver to acquire the regulators only when a
display of particular type is initialized. For example, vdds_sdi is
acquired when sdi_init_display() is called.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
MODULE_PARM_DESC() takes the name of the actual module parameter, not the
name of the variable, as input. Fix the module parameter description for
def_disp.
Signed-off-by: Jani Nikula <jani@nikula.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dss struct in dss.c has omap2/3 specific clock names. Making them generic,
to increase readability and extendability.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
enum dss_clock structure is replaced with generic names that
could be used across OMAP2420, 2430, 3xxx, 44xx platforms.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, clock database has <dev, clock-name> tuples for DSS2. Because of
this, the clock names are different across different OMAP platforms.
This patch aligns the DSS2 clock names and roles across OMAP 2420, 2430, 3xxx,
44xx platforms in the clock databases, hwmod databases for opt-clocks, and DSS
clock handling.
This ensures that clk_get/put/enable/disable APIs in DSS can use uniform role
names.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS IRQ number can be obtained from platform_get_irq(). This API in turn
picks the right IRQ number belonging to HW IP from the hwmod database.
So hardcoding of IRQ number could be removed.
This IRQ is stored in dss_irq as part of dss structure, and freed it in
dss_exit().
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS, DISPC, DSI, RFBI, VENC baseaddr can be obtained from platform_get_resource().
This API in turn picks the right silicon baseaddr from the hwmod database.
So hardcoding of base addr could be removed.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch replaces printk's in the init/probe functions to dev_dbg
for boot time optimization.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DSI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
Also, vdds_dsi regulator handling is copied to dsi.c, since vdds_dsi regulator is
needed by dpi_init() too. Board files are updated accordingly to add 2 instances of
vdds_dsi regulator.
DSI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for VENC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
Also, venc_vdda_dac reading is moved to venc.c.
VENC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
