Directly call IPv4 and IPv6 variants where the address family is
easily known.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Connection tracking helpers (specifically FTP) need to be called
before NAT sequence numbers adjustments are performed to be able
to compare them against previously seen ones. We've introduced
two new hooks around 2.6.11 to maintain this ordering when NAT
modules were changed to get called from conntrack helpers directly.
The cost of netfilter hooks is quite high and sequence number
adjustments are only rarely needed however. Add a RCU-protected
sequence number adjustment function pointer and call it from
IPv4 conntrack after calling the helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Adding extensions to confirmed conntracks is not allowed to avoid races
on reallocation. Don't setup NAT for confirmed conntracks in case NAT
module is loaded late.
The has one side-effect, the connections existing before the NAT module
was loaded won't enter the bysource hash. The only case where this actually
makes a difference is in case of SNAT to a multirange where the IP before
NAT is also part of the range. Since old connections don't enter the
bysource hash the first new connection from the IP will have a new address
selected. This shouldn't matter at all.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Locally generated ICMP packets have a reference to the conntrack entry
of the original packet manually attached by icmp_send(). Therefore the
check for locally originated untracked ICMP redirects can never be
true.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Move responsibility for setting the IP_NAT_RANGE_PROTO_SPECIFIED flag
to the NAT protocol, properly propagate errors and get rid of ugly
return value convention.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Move to nf_nat_proto_common and rename to nf_nat_proto_... since they're
also used by protocols that don't have port numbers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
The port rover should not get overwritten when using random mode,
otherwise other rules will also use more or less random ports.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Rule dumping is performed in two steps: first userspace gets the
ruleset size using getsockopt(SO_GET_INFO) and allocates memory,
then it calls getsockopt(SO_GET_ENTRIES) to actually dump the
ruleset. When another process changes the ruleset in between the
sizes from the first getsockopt call doesn't match anymore and
the kernel aborts. Unfortunately it returns EAGAIN, as for multiple
other possible errors, so userspace can't distinguish this case
from real errors.
Return EAGAIN so userspace can retry the operation.
Fixes (with current iptables SVN version) netfilter bugzilla #104.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit 9335f047fe aka
"[NETFILTER]: ip_tables: per-netns FILTER, MANGLE, RAW"
added per-netns _view_ of iptables rules. They were shown to user, but
ignored by filtering code. Now that it's possible to at least ping loopback,
per-netns tables can affect filtering decisions.
netns is taken in case of
PRE_ROUTING, LOCAL_IN -- from in device,
POST_ROUTING, LOCAL_OUT -- from out device,
FORWARD -- from in device which should be equal to out device's netns.
This code is relatively new, so BUG_ON was plugged.
Wrappers were added to a) keep code the same from CONFIG_NET_NS=n users
(overwhelming majority), b) consolidate code in one place -- similar
changes will be done in ipv6 and arp netfilter code.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Dump the mark value in log messages similar to nfnetlink_log. This
is useful for debugging complex setups where marks are used for
routing or traffic classification.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Consider we are putting a clusterip_config entry with the "entries"
count == 1, and on the other CPU there's a clusterip_config_find_get
in progress:
CPU1: CPU2:
clusterip_config_entry_put: clusterip_config_find_get:
if (atomic_dec_and_test(&c->entries)) {
/* true */
read_lock_bh(&clusterip_lock);
c = __clusterip_config_find(clusterip);
/* found - it's still in list */
...
atomic_inc(&c->entries);
read_unlock_bh(&clusterip_lock);
write_lock_bh(&clusterip_lock);
list_del(&c->list);
write_unlock_bh(&clusterip_lock);
...
dev_put(c->dev);
Oops! We have an entry returned by the clusterip_config_find_get,
which is a) not in list b) has a stale dev pointer.
The problems will happen when the CPU2 will release the entry - it
will remove it from the list for the 2nd time, thus spoiling it, and
will put a stale dev pointer.
The fix is to make atomic_dec_and_test under the clusterip_lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Without this patch, the generic L3 tracker would kick in
if nf_conntrack_ipv4 was not loaded before nf_nat, which
would lead to translation problems with ICMP errors.
NAT does not make sense without IPv4 connection tracking
anyway, so just add a call to need_ipv4_conntrack().
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This elliminates infamous race during module loading when one could lookup
proc entry without proc_fops assigned.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize call routing between NATed endpoints: when an external
registrar sends a media description that contains an existing RTP
expectation from a different SNATed connection, the gatekeeper
is trying to route the call directly between the two endpoints.
We assume both endpoints can reach each other directly and
"un-NAT" the addresses, which makes the media stream go between
the two endpoints directly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SDP connection addresses may be contained in the payload multiple
times (in the session description and/or once per media description),
currently only the session description is properly updated. Split up
SDP mangling so the function setting up expectations only updates the
media port, update connection addresses from media descriptions while
parsing them and at the end update the session description when the
final addresses are known.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create expectations for the RTCP connections in addition to RTP connections.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create expectations for incoming signalling connections when seeing
a REGISTER request. This is needed when the registrar uses a
different source port number for signalling messages and for receiving
incoming calls from other endpoints than the registrar.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIP message may contain multiple Contact: addresses referring to
the NATed endpoint, translate all of them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update maddr=, received= and rport= Via-header parameters refering to
the signalling connection.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform NAT last after parsing the packet. This makes no difference
currently, but is needed when dealing with registrations to make
sure we seen the unNATed addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the URI parsing helper to get the numerical addresses and get rid of the
text based header translation.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new function for SIP header parsing that properly deals with
continuation lines and whitespace in headers and use it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The request URI is not a header and needs to be treated differently than
real SIP headers. Add a seperate function for parsing it and get rid of
the POS_REQ_URI/POS_REG_REQ_URI definitions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SDP and SIP headers are quite different, SIP can have continuation lines,
leading and trailing whitespace after the colon and is mostly case-insensitive
while SDP headers always begin on a new line and are followed by an equal
sign and the value, without any whitespace.
Introduce new SDP header parsing function and convert all users that used
the SIP header parsing function. This will allow to properly deal with the
special SIP cases in the SIP header parsing function later.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace sizeof/memcmp by strlen/strcmp. Use case-insensitive comparison
for SIP methods and the SIP/2.0 string, as specified in RFC 3261.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conntrack reference and ctinfo can be derived from the packet.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After mangling the packet, the pointer to the data and the length of the data
portion may change and need to be adjusted.
Use double data pointers and a pointer to the length everywhere and add a
helper function to the NAT helper for performing the adjustments.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
