Stupidly use kzalloc() instead of kmalloc()/memset()
everywhere where this is possible in net/ipv6/*.c .
Signed-off-by: Ingo Oeser <ioe-lkml@rameria.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes these problems in MLDv2:
1) Add/remove "delete" records for sending change reports when
addition of a filter results in that filter transitioning to/from
inactive. [same as recent IPv4 IGMPv3 fix]
2) Remove 2 redundant "group_type" checks (can't be IPV6_ADDR_ANY
within that loop, so checks are always true)
3) change an is_in() "return 0" to "return type == MLD2_MODE_IS_INCLUDE".
It should always be "0" to get here, but it improves code locality
to not assume it, and if some race allowed otherwise, doing
the check would return the correct result.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Procfs always output IPV6 addresses without the colon
characters, and we cannot change that.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are errors and inconsistency in the display of NIP6 strings.
ie: net/ipv6/ip6_flowlabel.c
There are errors and inconsistency in the display of NIPQUAD strings too.
ie: net/netfilter/nf_conntrack_ftp.c
This patch:
adds NIP6_FMT to kernel.h
changes all code to use NIP6_FMT
fixes net/ipv6/ip6_flowlabel.c
adds NIPQUAD_FMT to kernel.h
fixes net/netfilter/nf_conntrack_ftp.c
changes a few uses of "%u.%u.%u.%u" to NIPQUAD_FMT for symmetry to NIP6_FMT
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes more unneeded casts on the return value for kmalloc(),
sock_kmalloc(), and vmalloc().
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The below "jumbo" patch fixes the following problems in MLDv2.
1) Add necessary "ntohs" to recent "pskb_may_pull" check [breaks
all nonzero source queries on little-endian (!)]
2) Add locking to source filter list [resend of prior patch]
3) fix "mld_marksources()" to
a) send nothing when all queried sources are excluded
b) send full exclude report when source queried sources are
not excluded
c) don't schedule a timer when there's nothing to report
NOTE: RFC 3810 specifies the source list should be saved and each
source reported individually as an IS_IN. This is an obvious DOS
path, requiring the host to store and then multicast as many sources
as are queried (e.g., millions...). This alternative sends a full,
relevant report that's limited to number of sources present on the
machine.
4) fix "add_grec()" to send empty-source records when it should
The original check doesn't account for a non-empty source
list with all sources inactive; the new code keeps that
short-circuit case, and also generates the group header
with an empty list if needed.
5) fix mca_crcount decrement to be after add_grec(), which needs
its original value
These issues (other than item #1 ;-) ) were all found by Yan Zheng,
much thanks!
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing default of 10 is just way too low.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: David Stevens <dlstevens@us.ibm.com>
As explained at:
http://www.cs.ucsb.edu/~krishna/igmp_dos/
With IGMP version 1 and 2 it is possible to inject a unicast
report to a client which will make it ignore multicast
reports sent later by the router.
The fix is to only accept the report if is was sent to a
multicast or unicast address.
Signed-off-by: David S. Miller <davem@davemloft.net>
And filter mode is exclude.
Further explanation by David Stevens:
Multicast source filters aren't widely used yet, and that's really the only
feature that's affected if an application actually exercises this bug, as far
as I can tell. An ordinary filter-less multicast join should still work, and
only forwarded multicast traffic making use of filters and doing empty-source
filters with the MSFILTER ioctl would be at risk of not getting multicast
traffic forwarded to them because the reports generated would not be based on
the correct counts.
Signed-off-by: Yan Zheng <yanzheng@21cn.com
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
5.1.3. Maximum Response Code
The Maximum Response Code field specifies the maximum time allowed
before sending a responding Report. The actual time allowed, called
the Maximum Response Delay, is represented in units of milliseconds,
and is derived from the Maximum Response Code as follows:
If Maximum Response Code < 32768,
Maximum Response Delay = Maximum Response Code
If Maximum Response Code >=32768, Maximum Response Code represents a
floating-point value as follows:
0 1 2 3 4 5 6 7 8 9 A B C D E F
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| exp | mant |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Maximum Response Delay = (mant | 0x1000) << (exp+3)
5.1.9. QQIC (Querier's Query Interval Code)
The Querier's Query Interval Code field specifies the [Query
Interval] used by the Querier. The actual interval, called the
Querier's Query Interval (QQI), is represented in units of seconds,
and is derived from the Querier's Query Interval Code as follows:
If QQIC < 128, QQI = QQIC
If QQIC >= 128, QQIC represents a floating-point value as follows:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|1| exp | mant |
+-+-+-+-+-+-+-+-+
QQI = (mant | 0x10) << (exp + 3)
-- rfc3810
#define MLDV2_QQIC(value) MLDV2_EXP(0x80, 4, 3, value)
#define MLDV2_MRC(value) MLDV2_EXP(0x8000, 12, 3, value)
Above macro are defined in mcast.c. but 1 << 4 == 0x10 and 1 << 12 == 0x1000.
So the result computed by original Macro is larger.
Signed-off-by: Yan Zheng <yanzheng@21cn.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-Off-By: Yan Zheng <yanzheng@21cn.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes line dupes at /ipv4/igmp.c and /ipv6/mcast.c in the
2.6 kernel, where MCAST_EXCLUDE is mistakenly used instead of
MCAST_INCLUDE.
Signed-off-by: Denis Lukianov <denis@voxelsoft.com>
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Adds (INCLUDE, empty)/leave-group equivalence to the full-state
multicast source filter APIs (IPv4 and IPv6)
2) Fixes an incorrect errno in the IPv6 leave-group (ENOENT should be
EADDRNOTAVAIL)
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) In the full-state API when imsf_numsrc == 0
errno should be "0", but returns EADDRNOTAVAIL
2) An illegal filter mode change
errno should be EINVAL, but returns EADDRNOTAVAIL
3) Trying to do an any-source option without IP_ADD_MEMBERSHIP
errno should be EINVAL, but returns EADDRNOTAVAIL
4) Adds comments for the less obvious error return values
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netfilter assumes that skb->data == skb->nh.ipv6h
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a simplified version of the patch to fix a bug in IPv6
multicasting. It:
1) adds existence check & EADDRINUSE error for regular joins
2) adds an exception for EADDRINUSE in the source-specific multicast
join (where a prior join is ok)
3) adds a missing/needed read_lock on sock_mc_list; would've raced
with destroying the socket on interface down without
4) adds a "leave group" in the (INCLUDE, empty) source filter case.
This frees unneeded socket buffer memory, but also prevents
an inappropriate interaction among the 8 socket options that
mess with this. Some would fail as if in the group when you
aren't really.
Item #4 had a locking bug in the last version of this patch; rather than
removing the idev->lock read lock only, I've simplified it to remove
all lock state in the path and treat it as a direct "leave group" call for
the (INCLUDE,empty) case it covers. Tested on an MP machine. :-)
Much thanks to HoerdtMickael <hoerdt@clarinet.u-strasbg.fr> who
reported the original bug.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
