A no-op tracer which can serve two purposes:
1. A template for development of a new tracer.
2. A convenient way to see ftrace_printk() calls without
an irrelevant trace making the output messy.
[ mingo@elte.hu: resolved conflicts ]
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is another tracer using the ftrace infrastructure, that examines
at each function call the size of the stack. If the stack use is greater
than the previous max it is recorded.
You can always see (and set) the max stack size seen. By setting it
to zero will start the recording again. The backtrace is also available.
For example:
# cat /debug/tracing/stack_max_size
1856
# cat /debug/tracing/stack_trace
[<c027764d>] stack_trace_call+0x8f/0x101
[<c021b966>] ftrace_call+0x5/0x8
[<c02553cc>] clocksource_get_next+0x12/0x48
[<c02542a5>] update_wall_time+0x538/0x6d1
[<c0245913>] do_timer+0x23/0xb0
[<c0257657>] tick_do_update_jiffies64+0xd9/0xf1
[<c02576b9>] tick_sched_timer+0x4a/0xad
[<c0250fe6>] __run_hrtimer+0x3e/0x75
[<c02518ed>] hrtimer_interrupt+0xf1/0x154
[<c022c870>] smp_apic_timer_interrupt+0x71/0x84
[<c021b7e9>] apic_timer_interrupt+0x2d/0x34
[<c0238597>] finish_task_switch+0x29/0xa0
[<c05abd13>] schedule+0x765/0x7be
[<c05abfca>] schedule_timeout+0x1b/0x90
[<c05ab4d4>] wait_for_common+0xab/0x101
[<c05ab5ac>] wait_for_completion+0x12/0x14
[<c033cfc3>] blk_execute_rq+0x84/0x99
[<c0402470>] scsi_execute+0xc2/0x105
[<c040250a>] scsi_execute_req+0x57/0x7f
[<c043afe0>] sr_test_unit_ready+0x3e/0x97
[<c043bbd6>] sr_media_change+0x43/0x205
[<c046b59f>] media_changed+0x48/0x77
[<c046b5ff>] cdrom_media_changed+0x31/0x37
[<c043b091>] sr_block_media_changed+0x16/0x18
[<c02b9e69>] check_disk_change+0x1b/0x63
[<c046f4c3>] cdrom_open+0x7a1/0x806
[<c043b148>] sr_block_open+0x78/0x8d
[<c02ba4c0>] do_open+0x90/0x257
[<c02ba869>] blkdev_open+0x2d/0x56
[<c0296a1f>] __dentry_open+0x14d/0x23c
[<c0296b32>] nameidata_to_filp+0x24/0x38
[<c02a1c68>] do_filp_open+0x347/0x626
[<c02967ef>] do_sys_open+0x47/0xbc
[<c02968b0>] sys_open+0x23/0x2b
[<c021aadd>] sysenter_do_call+0x12/0x26
I've tested this on both x86_64 and i386.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Sat, 22 Mar 2008 13:07:47 +0100
Ingo Molnar <mingo@elte.hu> wrote:
> > > i'd suggest the following: pull x86.git and sched-devel.git into a
> > > single tree [the two will combine without rejects]. Then try to add a
> > > kernel/tracing/trace_mmiotrace.c ftrace plugin. The trace_sysprof.c
> > > plugin might be a good example.
> >
> > I did this and now I have mmiotrace enabled/disabled via the tracing
> > framework (what do we call this, since ftrace is one of the tracers?).
>
> cool! could you send the patches for that? (even if they are not fully
> functional yet)
Patch attached in the end. Nice to see how much code disappeared. I tried
to mark all the features I had to break with XXX-comments.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With the adding of the configuration changes in the Makefile to prevent
tracing of functions in the ftrace code, all tracing of all the ftrace
code has been removed. Unfortunately, one of the selftests, relied on
a function to be traced. With the new change, the function was no longer
traced and the test failed.
This patch separates out the test function into its own file so that
we can add the "-pg" flag to the compilation of that function and the
adding of the mcount call to that function.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add preempt off timings. A lot of kernel core code is taken from the RT patch
latency trace that was written by Ingo Molnar.
This adds "preemptoff" and "preemptirqsoff" to /debugfs/tracing/available_tracers
Now instead of just tracing irqs off, preemption off can be selected
to be recorded.
When this is selected, it shares the same files as irqs off timings.
One can either trace preemption off, irqs off, or one or the other off.
By echoing "preemptoff" into /debugfs/tracing/current_tracer, recording
of preempt off only is performed. "irqsoff" will only record the time
irqs are disabled, but "preemptirqsoff" will take the total time irqs
or preemption are disabled. Runtime switching of these options is now
supported by simpling echoing in the appropriate trace name into
/debugfs/tracing/current_tracer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds the latency tracer infrastructure. This patch
does not add anything that will select and turn it on, but will
be used by later patches.
If it were to be compiled, it would add the following files
to the debugfs:
The root tracing directory:
/debugfs/tracing/
This patch also adds the following files:
available_tracers
list of available tracers. Currently no tracers are
available. Looking into this file only shows
"none" which is used to unregister all tracers.
current_tracer
The trace that is currently active. Empty on start up.
To switch to a tracer simply echo one of the tracers that
are listed in available_tracers:
example: (used with later patches)
echo function > /debugfs/tracing/current_tracer
To disable the tracer:
echo disable > /debugfs/tracing/current_tracer
tracing_enabled
echoing "1" into this file starts the ftrace function tracing
(if sysctl kernel.ftrace_enabled=1)
echoing "0" turns it off.
latency_trace
This file is readonly and holds the result of the trace.
trace
This file outputs a easier to read version of the trace.
iter_ctrl
Controls the way the output of traces look.
So far there's two controls:
echoing in "symonly" will only show the kallsyms variables
without the addresses (if kallsyms was configured)
echoing in "verbose" will change the output to show
a lot more data, but not very easy to understand by
humans.
echoing in "nosymonly" turns off symonly.
echoing in "noverbose" turns off verbose.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If CONFIG_FTRACE is selected and /proc/sys/kernel/ftrace_enabled is
set to a non-zero value the ftrace routine will be called everytime
we enter a kernel function that is not marked with the "notrace"
attribute.
The ftrace routine will then call a registered function if a function
happens to be registered.
[ This code has been highly hacked by Steven Rostedt and Ingo Molnar,
so don't blame Arnaldo for all of this ;-) ]
Update:
It is now possible to register more than one ftrace function.
If only one ftrace function is registered, that will be the
function that ftrace calls directly. If more than one function
is registered, then ftrace will call a function that will loop
through the functions to call.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
