it's expected that the transceiver driver will
initialize and call the notifier chain when
necessary. Implement that for twl4030-usb driver.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The notifier will be used to communicate usb events
to other drivers like the charger chip.
This can be used as source of information to kick
usb charger detection as described by the USB
Battery Charging Specification 1.1 and/or to
pass bMaxPower field of selected usb_configuration
to charger chip in order to use that information
as input current on the charging profile
setup.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An incorrect sizeof() resulted in only 4 (or 8) octets of the CHID being
checked instead of all 16 octets. A randomly generated CHID had a
probability of being unable to start a WUSB host of less than 1 in
2 billion.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_add_endpoint() is used in the reset path. It must
use GFP_NOIO to avoid a possible deadlock.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update cdc-acm to the async methods eliminating the workqueue
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use platform_get_resource() to fetch the memory resource and
resource_size() for calculate the length.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI FSL controller preserve its state during sleep mode, so nothing
fancy needs to be done.
Though, during 'deep sleep' mode (as found in MPC831x CPUs) the
controller turns off and needs to be reinitialized upon resume.
This patch adds support for hibernation and resuming after deep sleep.
Based on Dave Liu and Jerry Huang's work[1].
[1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patch
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes following warnings:
ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static?
ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix audio record functionality for some Full speed sound blaster devices.
Issue: Sometimes transaction complete indication is coming from HW one frame later.
Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction
is not finished yet, exit scan_periodic function and check the same transaction in the next frame.
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called.
In such case USB Host stacked during disconnect operation
Solution: add call of free_cached_itd_list() function in disable_periodic()
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset. The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens. Update hub_port_init() to allow resetting a configured
device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is reset, the xHCI hardware must know, in order to match
the device state and disable all endpoints except control endpoint 0.
Issue a Reset Device command after a USB device is successfully reset.
Wait on the command to finish, and then cache or free the disabled
endpoint rings.
There are four different USB device states that the xHCI hardware tracks:
- disabled/enabled - device connection has just been detected,
- default - the device has been reset and has an address of 0,
- addressed - the device has a non-zero address but no configuration has
been set,
- configured - a set configuration succeeded.
The USB core may issue a port reset when a device is in any state, but the
Reset Device command will fail for a 0.96 xHC if the device is not in the
addressed or configured state. Don't consider this failure as an error,
but don't free any endpoint rings if this command fails.
A storage driver may request that the USB device be reset during error
handling, so use GPF_NOIO instead of GPF_KERNEL while allocating memory
for the Reset Device command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the hub emulation code to allow ports on an xHCI root hub to be
disabled. Add the code to clear the port enabled/disabled bit, and clear
the port enabled/disabled change bit. Like EHCI, the port cannot be
enabled by setting the port enabled/disabled bit. Instead, a port is
enabled by the host controller after a reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor the code to clear the port change bits in the port status
register. All port status change bits are write one to clear.
Remove a redundant port status read that was supposed to unblock any
posted writes. We read the port after the write to get the updated status
for debugging, so the port read after that is unnecessary.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All commands that can be issued to the xHCI hardware can come back with
vendor-specific "informational" completion codes. These are to be treated
like a successful completion code. Refactor out the code to test for the
range of these codes and print debugging messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xhci_command structure is the basic structure for issuing commands to
the xHCI hardware. It contains a struct completion (so that the issuing
function can wait on the command), command status, and a input context
that is used to pass information to the hardware. Not all commands need
the input context, so make it optional to allocate. Allow
xhci_free_container_ctx() to be passed a NULL input context, to make
freeing the xhci_command structure simple.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor out the code to cache or free endpoint rings from recently
dropped or disabled endpoints. This code will be used by a new function
to reset a device and disable all endpoints except control endpoint 0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we fail to queue an evaluate context command or a configure endpoint
command to the command ring in xhci_configure_endpoint(), we need to
remove the xhci_command structure from the device's command list before
returning. If the command is left on the command list, it will sit there
indefinitely, blocking commands submitted after this fails.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1316) adds some error checking to usb_submit_urb().
It's conditional on CONFIG_USB_DEBUG, so it won't affect normal users.
The new check makes sure that the actual type of the endpoint
described by urb->pipe agrees with the type encoded in the pipe value.
The USB error code documentation is updated to include the code
returned by the new check, and the usbfs SUBMITURB handler is updated
to use the correct pipe type when legacy user code tries to submit a
bulk transfer to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API
checker, so I have no choice but band-aid it quick. There's no attempt
to reuse DMA buffers. Control messages are only sent rarely anyway.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hardware reports wrong interrupt. Although such a situation should not
happen, the compiler complains about this access.
This patch adds a sanity check and generates warning to detect such
issues.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On various mxc boards, the intial ULPI reads resulted in a timeout
which prevented the transceiver to be identified and thus the ehci
device to be probed.
Initializing the hardware lines connected to the transceiver (through
pdata->init call) before actually enabling clocks and configuring
registers in the devices fixes this problem.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed CS5 and CS6 from data bits since these are not supported
in FTDI hardware.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Latency timeout was read but never stored on port probe. When
ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0
rather than the default 16ms.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We always push characters to ldisc immediately regardless of
ASYNC_LOW_LATENCY.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes:
Return an empty string for modulation
when there is no connection
Fix sysfs unload race conditions
Log firmware load process, remove delay
Add new configuration interface
Remove cxacru-cf.bin
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has never worked properly because wsize passed to
cxacru_cm() is incorrectly set to the number of values
instead of the data bytes. The maximum number of values
that can be set at once is 7 which means the device will
not get enough data to work with and none of the
configuration values will be used.
At least one existing cxacru-cf.bin file contains invalid
data which will prevent the modem from syncing properly.
Fixing it is likely to break existing systems, and the
new sysfs interface for setting configuration parameters
can provide the same functionality. A script is provided
to convert from the original format.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem can be configured using CM_REQUEST_CARD_DATA_SET,
although CM_REQUEST_CARD_DATA_GET does not return any data.
Tested by setting the modulation (0x0a) option.
There is a list of parameters in the following archive,
but the meaning of many of them is not well documented:
http://sourceforge.net/project/shownotes.php?release_id=301825
This source also indicates that the highest parameter set
is 0x4a but this varies by model so an arbitrary limit of
0x7f has been used (the index is a 32-bit integer).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Firmware writing takes 256ms per 4KB with OHCI, which
is very slow compared to 7ms per 4KB with UHCI.
Until I have access to a hardware USB analyser it may
not be possible to determine why this happens.
Instead of appearing to do nothing, log progress when
writing firmware and then log the ATM device information
when finished. Remove an unnecessary 4 second delay.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These commands were found by accident... fortunately
it still works even if the flash memory is erased,
despite having no USB device IDs.
Some example sysfs code for raw command access:
http://simon.arlott.org/pub/cxacru/raw.c
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible for usb_get_intfdata() to return NULL if
sysfs is accessed while the module is being unloaded or
the device is being removed.
Move the access code to an inline function in usbatm.h,
and return -ENODEV if any of the pointers are NULL.
It should not be possible for the instance data or atm
device to be invalid until after unbind() completes and
the sysfs attributes have been removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When attempting to read data that is not actually
an array of values, the length may be negative
which causes an Oops due to a likely access off
the end of the data array.
This bug should not occur under normal use unless
the device returns an invalid response.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is no connection, return an empty string
instead of "0" for the connection modulation.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
sata_via: Delay on vt6420 when starting ATAPI DMA write
ata: Detect Delkin Devices compact flash
pata_efar: Enable parallel scanning
pata_atiixp: enable parallel scan
[libata] pata_atiixp: add locking for parallel scanning
[libata] pata_efar: add locking for parallel scanning
libata: Pass host flags into the pci helper
[libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
libata: Allow pata_legacy to be built on non-ISA but PCI systems
pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
[libata] pata_at91: fix backslash-continued string
pata_via: store UDMA masks in via_isa_bridges table
pata_via: fix address setup timings underlocking
pata_serverworks: fix error message
pata_serverworks: fix PIO setup for the second channel
pata_efar: fix secondary port support
pata_cypress: fix PIO timings underclocking
pata_cs5535: use correct values for PIO1 and PIO2 data timings
pata_cmd64x: remove unused definitions
...
When writing a disc on certain lite-on dvd-writers (also rebadged
as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends
up in the datastream and on the disc, causing silent corruption.
Delaying between sending the CDB and starting DMA seems to
prevent this.
I do not know if there are burners that do not suffer from
this, but the patch should be safe for those as well.
There are many reports of this issue, but AFAICT no solution was
found before. For example:
http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.html
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I have a Delkin Devices compact flash card that isn't being recognized using the
SATA/PATA drivers.
The card is recognized and works with the deprecated ATA drivers.
The error I am seeing is:
ata1.00: failed to IDENTIFY (device reports invalid type, err_mask=0x0)
I tracked it down to ata_id_is_cfa() in include/linux/ata.h.
The Delkin card has id[0] set to 0x844a and id[83] set to 0.
This isn't what the kernel expects and is probably incorrect.
The simplest work-around is to add a check for 0x844a to ata_id_is_cfa().
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Again originally proposed by Bartlomiej but this does it by using the
generic helper logic instead.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was originally proposed by Bartlomiej but as a device specific
expansion of the init_one function rather than making the helper more
generic.
Enable the parallel scan via the generic flags.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
