The issue of the endless reprogramming loop due to a too small
min_delta_ns was fixed with the previous updates of the clock events
code, but we had no information about the spread of this problem. I
added a WARN_ON to get automated information via kerneloops.org and to
get some direct reports, which allowed me to analyse the affected
machines.
The WARN_ON has served its purpose and would be annoying for a release
kernel. Remove it and just keep the information about the increase of
the min_delta_ns value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have a bug in the calculation of the next jiffie to trigger the RTC
synchronisation. The aim here is to run sync_cmos_clock() as close as
possible to the middle of a second. Which means we want this function to
be called less than or equal to half a jiffie away from when now.tv_nsec
equals 5e8 (500000000).
If this is not the case for a given call to the function, for this purpose
instead of updating the RTC we calculate the offset in nanoseconds to the
next point in time where now.tv_nsec will be equal 5e8. The calculated
offset is then converted to jiffies as these are the unit used by the
timer.
Hovewer timespec_to_jiffies() used here uses a ceil()-type rounding mode,
where the resulting value is rounded up. As a result the range of
now.tv_nsec when the timer will trigger is from 5e8 to 5e8 + TICK_NSEC
rather than the desired 5e8 - TICK_NSEC / 2 to 5e8 + TICK_NSEC / 2.
As a result if for example sync_cmos_clock() happens to be called at the
time when now.tv_nsec is between 5e8 + TICK_NSEC / 2 and 5e8 to 5e8 +
TICK_NSEC, it will simply be rescheduled HZ jiffies later, falling in the
same range of now.tv_nsec again. Similarly for cases offsetted by an
integer multiple of TICK_NSEC.
This change addresses the problem by subtracting TICK_NSEC / 2 from the
nanosecond offset to the next point in time where now.tv_nsec will be
equal 5e8, effectively shifting the following rounding in
timespec_to_jiffies() so that it produces a rounded-to-nearest result.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Until the C1E patches arrived there where no users of periodic broadcast
before switching to oneshot mode. Now we need to trigger a possible
waiter for a periodic broadcast when switching to oneshot mode.
Otherwise we can starve them for ever.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If HLT stops the TSC, we'll fail to account idle time, thereby inflating the
actual process times. Fix this by re-calibrating the clock against GTOD when
leaving nohz mode.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The C1E/HPET bug reports on AMDX2/RS690 systems where tracked down to a
too small value of the HPET minumum delta for programming an event.
The clockevents code needs to enforce an interrupt event on the clock event
device in some cases. The enforcement code was stupid and naive, as it just
added the minimum delta to the current time and tried to reprogram the device.
When the minimum delta is too small, then this loops forever.
Add a sanity check. Allow reprogramming to fail 3 times, then print a warning
and double the minimum delta value to make sure, that this does not happen again.
Use the same function for both tick-oneshot and tick-broadcast code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While chasing the C1E/HPET bugreports I went through the clock events
code inch by inch and found that the broadcast device can be initialized
and shutdown multiple times. Multiple shutdowns are not critical, but
useless waste of time. Multiple initializations are simply broken. Another
CPU might have the device in use already after the first initialization and
the second init could just render it unusable again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In tick_oneshot_setup we program the device to the given next_event,
but we do not check the return value. We need to make sure that the
device is programmed enforced so the interrupt handler engine starts
working. Split out the reprogramming function from tick_program_event()
and call it with the device, which was handed in to tick_setup_oneshot().
Set the force argument, so the devices is firing an interrupt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The reprogramming of the periodic broadcast handler was broken,
when the first programming returned -ETIME. The clockevents code
stores the new expiry value in the clock events device next_event field
only when the programming time has not been elapsed yet. The loop in
question calculates the new expiry value from the next_event value
and therefor never increases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is a ordering related problem with clockevents code, due to which
clockevents_register_device() called after tickless/highres switch
will not work. The new clockevent ends up with clockevents_handle_noop as
event handler, resulting in no timer activity.
The problematic path seems to be
* old device already has hrtimer_interrupt as the event_handler
* new clockevent device registers with a higher rating
* tick_check_new_device() is called
* clockevents_exchange_device() gets called
* old->event_handler is set to clockevents_handle_noop
* tick_setup_device() is called for the new device
* which sets new->event_handler using the old->event_handler which is noop.
Change the ordering so that new device inherits the proper handler.
This does not have any issue in normal case as most likely all the clockevent
devices are setup before the highres switch. But, can potentially be affecting
some corner case where HPET force detect happens after the highres switch.
This was a problem with HPET in MSI mode code that we have been experimenting
with.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On the tickless system(CONFIG_NO_HZ=y and CONFIG_HIGH_RES_TIMERS=n), after
I made an offlined cpu online, I found this cpu's event handler was
tick_handle_periodic, not tick_nohz_handler.
After debuging, I found this bug was caused by the wrong tick mode. the
tick mode is not changed to NOHZ_MODE_INACTIVE when the cpu is offline.
This patch fixes this bug.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Found an interactivity problem on a quad core test-system - simple
CPU loops would occasionally delay the system un an unacceptable way.
After much debugging with Peter Zijlstra it turned out that the problem
is caused by the string of sched_clock() changes - they caused the CPU
clock to jump backwards a bit - which confuses the scheduler arithmetics.
(which is unsigned for performance reasons)
So revert:
# c300ba2: sched_clock: and multiplier for TSC to gtod drift
# c0c8773: sched_clock: only update deltas with local reads.
# af52a90: sched_clock: stop maximum check on NO HZ
# f7cce27: sched_clock: widen the max and min time
This solves the interactivity problems.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
* 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: fix invalid proc_handler for softlockup_panic
softlockup: fix watchdog task wakeup frequency
softlockup: fix watchdog task wakeup frequency
softlockup: show irqtrace
softlockup: print a module list on being stuck
softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
softlockup: fix false positives on nohz if CPU is 100% idle for more than 60 seconds
softlockup: fix softlockup_thresh fix
softlockup: fix softlockup_thresh unaligned access and disable detection at runtime
softlockup: allow panic on lockup
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Optimize various places where a pointer to the cpumask_of_cpu value
will result in reducing stack pressure.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'timers/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add PCI ID for 6300ESB force hpet
x86: add another PCI ID for ICH6 force-hpet
kernel-paramaters: document pmtmr= command line option
acpi_pm clccksource: fix printk format warning
nohz: don't stop idle tick if softirqs are pending.
pmtmr: allow command line override of ioport
nohz: reduce jiffies polling overhead
hrtimer: Remove unused variables in ktime_divns()
hrtimer: remove warning in hres_timers_resume
posix-timers: print RT watchdog message
* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (76 commits)
sched_clock: and multiplier for TSC to gtod drift
sched_clock: record TSC after gtod
sched_clock: only update deltas with local reads.
sched_clock: fix calculation of other CPU
sched_clock: stop maximum check on NO HZ
sched_clock: widen the max and min time
sched_clock: record from last tick
sched: fix accounting in task delay accounting & migration
sched: add avg-overlap support to RT tasks
sched: terminate newidle balancing once at least one task has moved over
sched: fix warning
sched: build fix
sched: sched_clock_cpu() based cpu_clock(), lockdep fix
sched: export cpu_clock
sched: make sched_{rt,fair}.c ifdefs more readable
sched: bias effective_load() error towards failing wake_affine().
sched: incremental effective_load()
sched: correct wakeup weight calculations
sched: fix mult overflow
sched: update shares on wakeup
...
Working with ftrace I would get large jumps of 11 millisecs or more with
the clock tracer. This killed the latencing timings of ftrace and also
caused the irqoff self tests to fail.
What was happening is with NO_HZ the idle would stop the jiffy counter and
before the jiffy counter was updated the sched_clock would have a bad
delta jiffies to compare with the gtod with the maximum.
The jiffies would stop and the last sched_tick would record the last gtod.
On wakeup, the sched clock update would compare the gtod + delta jiffies
(which would be zero) and compare it to the TSC. The TSC would have
correctly (with a stable TSC) moved forward several jiffies. But because the
jiffies has not been updated yet the clock would be prevented from moving
forward because it would appear that the TSC jumped too far ahead.
The clock would then virtually stop, until the jiffies are updated. Then
the next sched clock update would see that the clock was very much behind
since the delta jiffies is now correct. This would then jump the clock
forward by several jiffies.
This caused ftrace to report several milliseconds of interrupts off
latency at every resume from NO_HZ idle.
This patch adds hooks into the nohz code to disable the checking of the
maximum clock update when nohz is in effect. It resumes the max check
when nohz has updated the jiffies again.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case a cpu goes idle but softirqs are pending only an error message is
printed to the console. It may take a very long time until the pending
softirqs will finally be executed. Worst case would be a hanging system.
With this patch the timer tick just continues and the softirqs will be
executed after the next interrupt. Still a delay but better than a
hanging system.
Currently we have at least two device drivers on s390 which under certain
circumstances schedule a tasklet from process context. This is a reason
why we can end up with pending softirqs when going idle. Fixing these
drivers seems to be non-trivial.
However there is no question that the drivers should be fixed.
This patch shouldn't be considered as a bug fix. It just is intended to
keep a system running even if device drivers are buggy.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jan Glauber <jan.glauber@de.ibm.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
C1E on AMD machines is like C3 but without control from the OS. Up to
now we disabled the local apic timer for those machines as it stops
when the CPU goes into C1E. This excludes those machines from high
resolution timers / dynamic ticks, which hurts especially X2 based
laptops.
The current boot time C1E detection has another, more serious flaw
as well: some BIOSes do not enable C1E until the ACPI processor module
is loaded. This causes systems to stop working after that point.
To work nicely with C1E enabled machines we use a separate idle
function, which checks on idle entry whether C1E was enabled in the
Interrupt Pending Message MSR. This allows us to do timer broadcasting
for C1E and covers the late enablement of C1E as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix (probably theoretical only) rq->clock update bug:
in tick_nohz_update_jiffies() [which is called on all irq
entry on all cpus where the irq entry hits an idle cpu] we
call touch_softlockup_watchdog() before we update jiffies.
That works fine most of the time when idle timeouts are within
60 seconds. But when an idle timeout is beyond 60 seconds,
jiffies is updated with a jump of more than 60 seconds,
which causes a jump in cpu-clock of more than 60 seconds,
triggering a false positive.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change references from for_each_cpu_mask to for_each_cpu_mask_nr
where appropriate
Reviewed-by: Paul Jackson <pj@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no harm, when users can read the info and we ask often enough
during debugging for this kind of information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
File permissions for
/sys/devices/system/clocksource/clocksource0/available_clocksource
are 600 which allows write access. But this is in fact a read only
file. So change permissions to 400.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the leap second handling from second_overflow(), which doesn't have to
check for it every second anymore. With CONFIG_NO_HZ this also makes sure the
leap second is handled close to the full second. Additionally this makes it
possible to abort a leap second properly by resetting the STA_INS/STA_DEL
status bits.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
current_tick_length used to do a little more, but now it just returns
tick_length, which we can also access directly at the few places, where it's
needed.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As TICK_LENGTH_SHIFT is used for more than just the tick length, the name
isn't quite approriate anymore, so this renames it to NTP_SCALE_SHIFT.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for setting the TAI value (International Atomic Time). The
value is reported back to userspace via timex (as we don't have a
ntp_gettime() syscall).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
time_offset is already a 64bit value but its resolution barely used, so this
makes better use of it by replacing SHIFT_UPDATE with TICK_LENGTH_SHIFT.
Side note: the SHIFT_HZ in SHIFT_UPDATE was incorrect for CONFIG_NO_HZ and the
primary reason for changing time_offset to 64bit to avoid the overflow.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes time_freq to a 64bit value and makes it static (the only outside
user had no real need to modify it). Intermediate values were already 64bit,
so the change isn't that big, but it saves a little in shifts by replacing
SHIFT_NSEC with TICK_LENGTH_SHIFT. PPM_SCALE is then used to convert between
user space and kernel space representation.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a few more things from the ntp nanokernel related to user space.
It's now possible to select the resolution used of some values via STA_NANO
and the kernel reports in which mode it works (pll/fll).
If some values for adjtimex() are outside the acceptable range, they are now
simply normalized instead of letting the syscall fail. I removed
MOD_CLKA/MOD_CLKB as the mapping didn't really makes any sense, the kernel
doesn't support setting the clock.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly a style cleanup of ntp.c and extracts part of do_adjtimex as
ntp_update_offset(). Otherwise the functionality is still the same as before.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 is the only arch right now, which provides an optimized for
div_long_long_rem and it has the downside that one has to be very careful that
the divide doesn't overflow.
The API is a little akward, as the arguments for the unsigned divide are
signed. The signed version also doesn't handle a negative divisor and
produces worse code on 64bit archs.
There is little incentive to keep this API alive, so this converts the few
users to the new API.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This converts a few users of do_div to div_[su]64 and this demonstrates nicely
how it can reduce some expressions to one-liners.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Miller reported:
|--------------->
the following commit:
| commit 27ec440779
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Thu Feb 28 21:00:21 2008 +0100
|
| sched: make cpu_clock() globally synchronous
|
| Alexey Zaytsev reported (and bisected) that the introduction of
| cpu_clock() in printk made the timestamps jump back and forth.
|
| Make cpu_clock() more reliable while still keeping it fast when it's
| called frequently.
|
| Signed-off-by: Ingo Molnar <mingo@elte.hu>
causes watchdog triggers when a cpu exits NOHZ state when it has been
there for >= the soft lockup threshold, for example here are some
messages from a 128 cpu Niagara2 box:
[ 168.106406] BUG: soft lockup - CPU#11 stuck for 128s! [dd:3239]
[ 168.989592] BUG: soft lockup - CPU#21 stuck for 86s! [swapper:0]
[ 168.999587] BUG: soft lockup - CPU#29 stuck for 91s! [make:4511]
[ 168.999615] BUG: soft lockup - CPU#2 stuck for 85s! [swapper:0]
[ 169.020514] BUG: soft lockup - CPU#37 stuck for 91s! [swapper:0]
[ 169.020514] BUG: soft lockup - CPU#45 stuck for 91s! [sh:4515]
[ 169.020515] BUG: soft lockup - CPU#69 stuck for 92s! [swapper:0]
[ 169.020515] BUG: soft lockup - CPU#77 stuck for 92s! [swapper:0]
[ 169.020515] BUG: soft lockup - CPU#61 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#85 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#101 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#109 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#117 stuck for 92s! [swapper:0]
[ 169.171483] BUG: soft lockup - CPU#40 stuck for 80s! [dd:3239]
[ 169.331483] BUG: soft lockup - CPU#13 stuck for 86s! [swapper:0]
[ 169.351500] BUG: soft lockup - CPU#43 stuck for 101s! [dd:3239]
[ 169.531482] BUG: soft lockup - CPU#9 stuck for 129s! [mkdir:4565]
[ 169.595754] BUG: soft lockup - CPU#20 stuck for 93s! [swapper:0]
[ 169.626787] BUG: soft lockup - CPU#52 stuck for 93s! [swapper:0]
[ 169.626787] BUG: soft lockup - CPU#84 stuck for 92s! [swapper:0]
[ 169.636812] BUG: soft lockup - CPU#116 stuck for 94s! [swapper:0]
It's simple enough to trigger this by doing a 10 minute sleep after a
fresh bootup then starting a parallel kernel build.
I suspect this might be reintroducing a problem we've had and fixed
before, see the thread:
http://marc.info/?l=linux-kernel&m=119546414004065&w=2
<---------------|
touch the softlockup watchdog when exiting NOHZ state - we are
obviously not locked up.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
hrtimer: optimize the softirq time optimization
hrtimer: reduce calls to hrtimer_get_softirq_time()
clockevents: fix typo in tick-broadcast.c
jiffies: add time_is_after_jiffies and others which compare with jiffies
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
braodcast -> broadcast
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Various SMP balancing algorithms require that the bandwidth period
run in sync.
Possible improvements are moving the rt_bandwidth thing into root_domain
and keeping a span per rt_bandwidth which marks throttled cpus.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
