Firmware encodes the number of MSI-X requested by a device in a
different property than for MSI. Pull the property name out as a
parameter and share the logic for both cases.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to increment i in the loop that queries what interrupts firmware
gave us, otherwise we'll incorrectly use the first value over and over.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lmb debugging can be turned on at boottime with lmb=debug on the
command line. However on powerpc that doesn't work, because we don't
necessarily call lmb_dump_all().
So always call lmb_dump_all() after lmb_analyze(), no output is
generated unless lmb=debug is found on the command line.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we never hotplug add an isa bus, we never need to set primary.
Delete this write-only variable.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use of_get_cpu_node, which is a superset of numa.c's find_cpu_node in
a less restrictive section (text vs cpuinit).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
find_min_common_depth() was checking the property length incorrectly.
The value is in bytes not cells, and it is using the second entry.
Signed-off-By: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/platforms/pseries/hotplug-memory.c uses
remove_section_mapping() but doesn't include sparsemem.h which defines
it. This can cause compilation fails for some configs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new legacy_mem file in sysfs is causing problems with X on machines
that don't support legacy memory access. The way I initially implemented
it, we would fail with -ENXIO when trying to mmap it, thus exposing to
X that we do support the API but there is no legacy memory.
Unfortunately, X poor error handling is causing it to fail to start when
it gets this error.
This implements a workaround hack that instead maps anonymous memory
instead (using shmem if VM_SHARED is set, just like /dev/zero does).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/oprofile/cell/spu_profiler.c is missing a asm/time.h
include which is required for ppc_proc_freq. This can cause compile
failures for some config combinations.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: fix dynamic ftrace with large modules in PPC64
The math to calculate the offset into the TOC that is taken from reading
the trampoline is incorrect. The bottom half of the offset is a signed
extended short. The current code was using an OR to create the offset
when it should have been using an addition.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently emulate_step() emulates mr. instructions without updating cr0
and this can be disastrous. Don't emulate mr.
This bug has been around for a while, but I am not sure if its a worthy
-stable candidate. I'll leave it to Ben do decide.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixed v_mapped_by_tlbcam() and p_mapped_by_tlbcam() to use phys_addr_t
instead of unsigned long. In 36-bit physical mode we really need these
functions to deal with phys_addr_t when trying to match a physical
address or when returning one.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add appropriate sdhci nodes.
Note that U-Boot should configure pin multiplexing for eSDHC prior
to Linux could use it. U-Boot should also fill-in the clock-frequency
property (eSDHC clock depends on board-specific SCCR[ESDHCCM] bits).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- sdhc node renamed to sdhci ("sdhc" name is confusing since SDHC is
used to name Secure Digital High Capacity cards, while SDHCI is an
interface).
- Get rid of "fsl,esdhc" compatible entry, it's replaced by the
"fsl,<chip>-esdhc" scheme;
- Get rid of `model' property.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Taking sizeof the result of sizeof is quite strange and does not seem to be
what is wanted here.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- sizeof (
sizeof (E)
- )
@@
type T;
@@
- sizeof (
sizeof (T)
- )
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is a simple change to correct problems when using set_irq_type
on platforms using CPM2. This code corrects the problem on most platform
but may have issues on 8272 derived platforms for some interrupts.
On 8272 PC2 & 3 are missing and PC 23 & 29 are added, which this patch
does not address.
Signed-off-by: Paul Bilke <paul@conspiracy.net>
Reviewed-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:
DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I noticed this doing some randconfig testing (.config below). I have
CONFIG_PM but no CONFIG_SUSPEND. Bug is against mainline.
arch/powerpc/sysdev/built-in.o: In function `ipic_suspend':
ipic.c:(.text+0x6b34): undefined reference to `fsl_deep_sleep'
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
Looks like #ifdef CONFIG_PM in arch/powerpc/sysdev/ipic.c should be
CONFIG_SUSPEND. d49747bdfb introduced
this.
Fix build when we have CONFIG_PM but no CONFIG_SUSPEND.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds board support for the Media5200 platform. Changes are:
- add the media5200 device tree
- add the media5200 platform support code and cascaded interrupt controller
- add media5200 to the build targets.
Note: this patch also includes a minor tweak to the lite5200(b) target
images list to add the .dtb files to the image list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds IRQ controller support to the MPC5200 General
Purpose Timer (GPT) device driver. With this patch the mpc5200-gpt
driver supports both GPIO and IRQ functions.
The GPT driver was contained within the mpc52xx_gpio.c file, but this
patch moves it out into a new file (mpc52xx_gpt.c) since it has more
than just GPIO functionality now and it was only grouped with the
mpc52xx-gpio drivers as a matter of convenience before. Also, this
driver will most likely get extended again to also provide support
for the timer function.
Implementation note: Alternately, I could have tried to implement
the IRQ support as a separate driver and left the GPIO portion alone.
However, multiple functions of this device (ie. GPIO input+interrupt
controller, or timer+GPIO) can be active at the same time and the
registers are shared so it is safer to contain all functionality
within a single driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Rework the mpc5200-pic driver to simplify it and fix up the setting
of desc->status when set_type is called for internal IRQs (so they
are reported as level, not edge). The simplification is due to
splitting off the handling of external IRQs into a separate block
so they don't need to be handled as exceptions in the normal
CRIT, MAIN and PERP paths.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pr_debug() calls in the 'hot' *_mask(), *_unmask(), *_ack() and
get_irq() makes adding #define DEBUG pretty much useless. Remove
these calls because they completely swamp the output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Trim out obsolete/extraneous properties and tighten up some usage
conventions. Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
nodes
- Move common interrupt-parent property out of device nodes and
into top level parent node.
This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness. Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Automatic I2C device probing is not done any more. Therefore we need
proper DTS device node definitions for the I2C LM75 thermal sensor on
the TQM85xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Recently, a patch left DEBUG enabled in the powerpc common PCI code,
resulting in an old bug in a pr_debug() statement to show up and cause
a NULL dereference on some machines.
This fixes the pr_debug() statement and reverts to DEBUG not being
force-enabled in that file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch ensures that memory gets properly mapped into the PCI
address space. Without this patch, the memory window BAR is left
at whatever value happened to be loaded into the BAR when Linux
was booted. Without this patch, memory could end up getting mapped
at any of the 1G address boundaries instead of at '0' where Linux
expects it.
Similarly, this patch also ensures that the internally memory mapped
registers (IMMR) are mapped to the correct PCI address range.
Without this patch, PCI appears to work correctly until a PCI
device is inserted which DMAs into memory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds basic support for the 6 GPIO lines found on GE Fanucs SBC310 to the GE Fanuc GPIO driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the default config file for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The FSL PCI code depends on PCI quirks being enabled to function
properly. We can ensure this by doing a select in Kconfig of
PCI_QUIRKS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of rounding the divider down, improve the baud-rate generators
accuracy by rounding to the nearest integer.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On booke processors, the code that maps low memory only uses up to three
CAM entries, even though there are sixteen and nothing else uses them.
Make this number configurable in the advanced options menu along with max
low memory size. If one wants 1 GB of lowmem, then it's typically
necessary to have four CAM entries.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code that maps kernel low memory would only use page sizes up to 256
MB. On E500v2 pages up to 4 GB are supported.
However, a page must be aligned to a multiple of the page's size. I.e.
256 MB pages must aligned to a 256 MB boundary. This was enforced by a
requirement that the physical and virtual addresses of the start of lowmem
be aligned to 256 MB. Clearly requiring 1GB or 4GB alignment to allow
pages of that size isn't acceptable.
To solve this, I simply have adjust_total_lowmem() take alignment into
account when it decides what size pages to use. Give it PAGE_OFFSET =
0x7000_0000, PHYSICAL_START = 0x3000_0000, and 2GB of RAM, and it will map
pages like this:
PA 0x3000_0000 VA 0x7000_0000 Size 256 MB
PA 0x4000_0000 VA 0x8000_0000 Size 1 GB
PA 0x8000_0000 VA 0xC000_0000 Size 256 MB
PA 0x9000_0000 VA 0xD000_0000 Size 256 MB
PA 0xA000_0000 VA 0xE000_0000 Size 256 MB
Because the lowmem mapping code now takes alignment into account,
PHYSICAL_ALIGN can be lowered from 256 MB to 64 MB. Even lower might be
possible. The lowmem code will work down to 4 kB but it's possible some of
the boot code will fail before then. Poor alignment will force small pages
to be used, which combined with the limited number of TLB1 pages available,
will result in very little memory getting mapped. So alignments less than
64 MB probably aren't very useful anyway.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code to map lowmem uses three CAM aka TLB[1] entries to cover it. The
size of each is stored in three globals named __cam0, __cam1, and __cam2.
All the code that uses them is duplicated three times for each of the three
variables.
We have these things called arrays and loops....
Once converted to use an array, it will be easier to make the number of
CAMs configurable.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We currently have a few variants of fsl-booke processors (e500v1, e500v2,
e500mc, and e200). They all have minor differences that we had previously
been handling via ifdefs.
To move towards having this support the following changes have been made:
* PID1, PID2 only exist on e500v1 & e500v2 and should not be accessed on
e500mc or e200. We use MMUCFG[NPIDS] to determine which case we are
since we only touch PID1/2 in extremely early init code.
* Not all IVORs exist on all the processors so introduce cpu_setup
functions for each variant to setup the proper IVORs that are either
unique or exist but have some variations between the processors
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for PCI-Express controllers as found on the
newer MPC83xx chips.
The work is loosely based on the Tony Li's patch[1], but unlike the
original patch, this patch implements sliding window for the Type 1
transactions using outbound window translations, so we don't have to
ioremap the whole PCI-E configuration space.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-January/049028.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.
This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.
Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove some leftover cruft from the arch/ppc days
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
