Support for the IT8172 IDE controller was removed from the kernel
sometime after 2.6.18. Support for the only boards that used the IT8172
was removed from the kernel after 2.6.18, as they had never compiled
since 2.6.0. However, there are a couple of platforms that use this
chip: the PMC-Sierra Xiao Hu thin-client computer, which is no longer
in production, and the Linksys NSS4000 Network Attached Storage box,
which is based on the Xiao Hu board. I am attempting to add support
for the Xiao Hu to the kernel, and this IT8172 IDE controller is the
first bit of code in this effort.
This patch resurrects the IT8172 IDE controller code. I began with
the 2.6.18 version of the it8172.c file, and have moved it forward so
that it works with the latest version of the kernel. I have run this
driver on a PMC-Sierra Xiao Hu board with the 2.6.28 kernel, and
I have had no problems with it in my configuration. The attached patch
applies cleanly against 2.6.28.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: alan@lxorguk.ukuu.org.uk
[bart: s/HWIF(drive)/drive->hwif/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This makes ide_port_scan()'s behavior match ide_host_register()'s
one and fixes OOPS in elv_may_queue() during port re-scan.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->cur_dev should now be always valid if ->handler is set so
remove redundant checks from ide_intr() and ide_timer_expiry().
* Apply CodingStyle fixups in ide_timer_expiry() while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->handler is set while it shouldn't be it indicates deep problems
so BUG_ON()-ning and preventing further damage is much more appropriate
than merely printing an error message.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... and remove no longer needed cdrom_start_packet_command and
cdrom_transfer_packet_command.
Tested lightly with ide-cd and ide-floppy.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
as it is done for all other IDE ATAPI devices.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... instead of assuming it is set for accelerated DRQ type devices.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According the documentation, id[ATA_ID_DWORD_IO] is non-zero if
the drive supports dword IO, while the code disables support by
setting IDE_DFLAG_NO_IO_32BIT. In addition, this word has been
reused by the ATA8 specification. This patch fixes both cases.
Signed-off-by: Mario Schwalbe <schwalbe@inf.tu-dresden.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove id[ATA_ID_DWORD_IO] check altogether per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_port_for_each_dev() / ide_host_for_each_port() iterators
and update IDE code to use them.
While at it:
- s/unit/i/ variable in ide_port_wait_ready(), ide_probe_port(),
ide_port_tune_devices(), ide_port_init_devices_data(), do_reset1(),
ide_acpi_set_state() and scc_dma_end()
- s/d/i/ variable in ide_proc_port_register_devices()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Allocate device structures dynamically instead of having them embedded
in ide_hwif_t:
* Remove needless zeroing of port structure from ide_init_port_data().
* Add ide_hwif_t.devices[MAX_DRIVES] (table of pointers to the devices).
* Add ide_port_{alloc,free}_devices() helpers and use them respectively
in ide_{host,free}_alloc().
* Convert all users of ->drives[] to use ->devices[] instead.
While at it:
* Use drive->dn for the slave device check in scc_pata.c.
As a nice side-effect this patch cuts ~1kB (x86-32) from the resulting
code size:
text data bss dec hex filename
53963 1244 237 55444 d894 drivers/ide/ide-core.o.before
52981 1244 237 54462 d4be drivers/ide/ide-core.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Because presence of the peer device was not checked in
it821x_set_pio_mode() PIO0 mode was used for taskfile PIO
in single device configurations.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove (now superfluous) ->error method from struct ide_driver.
* Unexport __ide_error() and make it static.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- s/struct ide_driver_s/struct ide_driver/
- use to_ide_driver() macro in ide-proc.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just use u8 instead, also s/__u8/u8/ in ide-cd.h while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move IDE_DEFAULT_MAX_FAILURES to <linux/ide.h>.
* Move ide_cfg_mtx, ide_hwif_to_major[], ide_port_init_devices_data(),
ide_init_port_data(), ide_init_port_hw() and ide_unregister() to
ide-probe.c from ide.c.
* Make ide_unregister(), ide_init_port_data(), ide_init_port_hw()
and ide_cfg_mtx static.
While at it:
* Remove stale ide_init_port_data() documentation and ide_lock extern.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->host_busy field to struct ide_host and use it's first bit
together with lock bitops to provide new ports serialization method.
* Convert core IDE code to use new ide_[un]lock_host() helpers.
This removes the need for taking hwgroup->lock if host is already
busy on serialized hosts and makes it possible to merge ide_hwgroup_t
into ide_hwif_t (done in the later patch).
* Remove no longer needed ide_hwgroup_t.busy and ide_[un]lock_hwgroup().
* Update do_ide_request() documentation.
v2:
* ide_release_lock() should be called inside IDE_HFLAG_SERIALIZE check.
* Add ide_hwif_t.busy flag and ide_[un]lock_port() for serializing
devices on a port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'int port_count' field to ide_hwgroup_t to keep the track
of the number of ports in the hwgroup. Then update init_irq()
and ide_remove_port_from_hwgroup() to use it.
* Remove no longer needed hwgroup->hwif, {drive,hwif}->next,
ide_add_drive_to_hwgroup() and ide_remove_drive_from_hwgroup()
(hwgroup->drive now only denotes the currently active device
in the hwgroup).
* Update locking documentation in <linux/ide.h>.
While at it:
* Rename ->drive field in ide_hwgroup_t to ->cur_dev.
* Use __func__ in ide_timer_expiry().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use hwif instead of hwgroup as {request,free}_irq()'s cookie,
teach ide_intr() to return early for non-active serialized ports,
modify unexpected_intr() accordingly and then use per-port IRQ
handlers instead of per-hwgroup ones.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass 'ide_hwif_t *' instead of 'ide_hwgroup_t *' to unexpected_intr().
* Cache pointer to the port currently being serviced in ->cur_port
and use it instead of hwif->hwgroup on serialized hosts.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix do_ide_request() to operate on previous device / port instead of
the current one. The original code was wrong since at least Feb 2002
(2.4.0 timeframe).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 295f00042a ("ide: don't execute
the next queued command from the hard-IRQ context") overlooked that
ide_do_drive_cmd() (used for REQUEST SENSE command handling) may still
invoke do_ide_request() (->request_fn) in the hard-IRQ context through
blk_start_queueing(). This resulted in a LOCKDEP warning after commit
b599bc7a1199419e122cb2e9ec6b0fa2cfbbc17b ("ide: use per-device request
queue locks (v2)").
Since calling blk_start_queuing() in ide_do_drive_cmd() doesn't make
much sense as the port is already marked as busy (so the execution of
the new command will be deferred anyway) then just remove it fixing
LOCKDEP warning and saving some CPU cycles at the same time.
Reported-and-tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Grissiom <chaos.proton@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Supply dm_add_exception as a callback to the read_metadata function.
Add a status function ready for a later patch and name the functions
consistently.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the existing snapshot exception store implementations out into
separate files. Later patches will place these behind a new
interface in preparation for alternative implementations.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename struct exception_store to dm_exception_store.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull structures that bridge the gap between snapshot and
exception store out of dm-snap.h and put them in a new
.h file - dm-exception-store.h. This file will define the
API for new exception stores.
Ultimately, dm-snap.h is unnecessary, since only dm-snap.c
should be using it.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The same workqueue is used both for sending uevents and processing queued I/O.
Deadlock has been reported in RHEL5 when sending a uevent was blocked waiting
for the queued I/O to be processed. Use scheduled_work() for the asynchronous
uevents instead.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement simple read-only sysfs entry for device-mapper block device.
This patch adds a simple sysfs directory named "dm" under block device
properties and implements
- name attribute (string containing mapped device name)
- uuid attribute (string containing UUID, or empty string if not set)
The kobject is embedded in mapped_device struct, so no additional
memory allocation is needed for initializing sysfs entry.
During the processing of sysfs attribute we need to lock mapped device
which is done by a new function dm_get_from_kobj, which returns the md
associated with kobject and increases the usage count.
Each 'show attribute' function is responsible for its own locking.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rework table reference counting.
The existing code uses a reference counter. When the last reference is
dropped and the counter reaches zero, the table destructor is called.
Table reference counters are acquired/released from upcalls from other
kernel code (dm_any_congested, dm_merge_bvec, dm_unplug_all).
If the reference counter reaches zero in one of the upcalls, the table
destructor is called from almost random kernel code.
This leads to various problems:
* dm_any_congested being called under a spinlock, which calls the
destructor, which calls some sleeping function.
* the destructor attempting to take a lock that is already taken by the
same process.
* stale reference from some other kernel code keeps the table
constructed, which keeps some devices open, even after successful
return from "dmsetup remove". This can confuse lvm and prevent closing
of underlying devices or reusing device minor numbers.
The patch changes reference counting so that the table destructor can be
called only at predetermined places.
The table has always exactly one reference from either mapped_device->map
or hash_cell->new_map. After this patch, this reference is not counted
in table->holders. A pair of dm_create_table/dm_destroy_table functions
is used for table creation/destruction.
Temporary references from the other code increase table->holders. A pair
of dm_table_get/dm_table_put functions is used to manipulate it.
When the table is about to be destroyed, we wait for table->holders to
reach 0. Then, we call the table destructor. We use active waiting with
msleep(1), because the situation happens rarely (to one user in 5 years)
and removing the device isn't performance-critical task: the user doesn't
care if it takes one tick more or not.
This way, the destructor is called only at specific points
(dm_table_destroy function) and the above problems associated with lazy
destruction can't happen.
Finally remove the temporary protection added to dm_any_congested().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement barrier support for single device DM devices
This patch implements barrier support in DM for the common case of dm linear
just remapping a single underlying device. In this case we can safely
pass the barrier through because there can be no reordering between
devices.
NB. Any DM device might cease to support barriers if it gets
reconfigured so code must continue to allow for a possible
-EOPNOTSUPP on every barrier bio submitted. - agk
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow NULL buffer in dm_copy_name_and_uuid if you only want to return one of
the fields.
(Required by a following patch that adds these fields to sysfs.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Check that the log bitmap will fit within the log device.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move log size validation from mirror target to log constructor.
Removed PAGE_SIZE restriction we no longer think necessary.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
rw_header function updates three members of io_req data every time
when I/O is processed. bi_rw and notify.fn are never modified once
they get initialized, and so they can be set in advance.
header_to_disk() can also be pulled out of write_header() since only one
caller needs it and write_header() can be replaced by rw_header()
directly.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change dm_unregister_target to return void and use BUG() for error
reporting.
dm_unregister_target can only fail because of programming bug in the
target driver. It can't fail because of user's behavior or disk errors.
This patch changes unregister_target to return void and use BUG if
someone tries to unregister non-registered target or unregister target
that is in use.
This patch removes code duplication (testing of error codes in all dm
targets) and reports bugs in just one place, in dm_unregister_target. In
some target drivers, these return codes were ignored, which could lead
to a situation where bugs could be missed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Always increase the error count when I/O on a leg of a mirror fails.
The error count is used to decide whether to select an alternative
mirror leg. If the target doesn't use the "handle_errors" feature, the
error count is not updated and the bio can get requeued forever by the
read callback.
Fix it by increasing error_count before the handle_errors feature
checking.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
