A while back there was a discussion regarding the rt_secret_interval timer.
Given that we've had the ability to do emergency route cache rebuilds for awhile
now, based on a statistical analysis of the various hash chain lengths in the
cache, the use of the flush timer is somewhat redundant. This patch removes the
rt_secret_interval sysctl, allowing us to rely solely on the statistical
analysis mechanism to determine the need for route cache flushes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lockdep facility temporarily disables lockdep checking by
incrementing the current->lockdep_recursion variable. Such
disabling happens in NMIs and in other situations where lockdep
might expect to recurse on itself.
This patch therefore checks current->lockdep_recursion, disabling RCU
lockdep splats when this variable is non-zero. In addition, this patch
removes the "likely()", as suggested by Lai Jiangshan.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Reported-by: David Miller <davem@davemloft.net>
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
Cc: eric.dumazet@gmail.com
LKML-Reference: <20100415195039.GA22623@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When CONFIG_DEBUG_BLOCK_EXT_DEVT is set we decode the device
improperly by old_decode_dev and it results in an error while
hibernating with s2disk.
All users already pass the new device number, so switch to
new_decode_dev().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
- We weren't zeroing p->rss_stat[] at fork()
- Consequently sync_mm_rss() was dereferencing tsk->mm for kernel
threads and was oopsing.
- Make __sync_task_rss_stat() static, too.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15648
[akpm@linux-foundation.org: remove the BUG_ON(!mm->rss)]
Reported-by: Troels Liebe Bentsen <tlb@rapanden.dk>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
"Michael S. Tsirkin" <mst@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Force MSI irq handlers to run with interrupts disabled
taskset on 2.6.34-rc3 fails on one of my ppc64 test boxes with
the following error:
sched_getaffinity(0, 16, 0x10029650030) = -1 EINVAL (Invalid argument)
This box has 128 threads and 16 bytes is enough to cover it.
Commit cd3d8031eb (sched:
sched_getaffinity(): Allow less than NR_CPUS length) is
comparing this 16 bytes agains nr_cpu_ids.
Fix it by comparing nr_cpu_ids to the number of bits in the
cpumask we pass in.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Sharyathi Nagesh <sharyath@in.ibm.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Mike Travis <travis@sgi.com>
LKML-Reference: <20100406070218.GM5594@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Module refcounting is implemented with a per-cpu counter for speed.
However there is a race when tallying the counter where a reference may
be taken by one CPU and released by another. Reference count summation
may then see the decrement without having seen the previous increment,
leading to lower than expected count. A module which never has its
actual reference drop below 1 may return a reference count of 0 due to
this race.
Module removal generally runs under stop_machine, which prevents this
race causing bugs due to removal of in-use modules. However there are
other real bugs in module.c code and driver code (module_refcount is
exported) where the callers do not run under stop_machine.
Fix this by maintaining running per-cpu counters for the number of
module refcount increments and the number of refcount decrements. The
increments are tallied after the decrements, so any decrement seen will
always have its corresponding increment counted. The final refcount is
the difference of the total increments and decrements, preventing a
low-refcount from being returned.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There have been a number of reports of people seeing the message:
"name_count maxed, losing inode data: dev=00:05, inode=3185"
in dmesg. These usually lead to people reporting problems to the filesystem
group who are in turn clueless what they mean.
Eventually someone finds me and I explain what is going on and that
these come from the audit system. The basics of the problem is that the
audit subsystem never expects a single syscall to 'interact' (for some
wish washy meaning of interact) with more than 20 inodes. But in fact
some operations like loading kernel modules can cause changes to lots of
inodes in debugfs.
There are a couple real fixes being bandied about including removing the
fixed compile time limit of 20 or not auditing changes in debugfs (or
both) but neither are small and obvious so I am not sending them for
immediate inclusion (I hope Al forwards a real solution next devel
window).
In the meantime this patch simply adds 'audit' to the beginning of the
crap message so if a user sees it, they come blame me first and we can
talk about what it means and make sure we understand all of the reasons
it can happen and make sure this gets solved correctly in the long run.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'slabh' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
eeepc-wmi: include slab.h
staging/otus: include slab.h from usbdrv.h
percpu: don't implicitly include slab.h from percpu.h
kmemcheck: Fix build errors due to missing slab.h
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
iwlwifi: don't include iwl-dev.h from iwl-devtrace.h
x86: don't include slab.h from arch/x86/include/asm/pgtable_32.h
Fix up trivial conflicts in include/linux/percpu.h due to
is_kernel_percpu_address() having been introduced since the slab.h
cleanup with the percpu_up.c splitup.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
module: add stub for is_module_percpu_address
percpu, module: implement and use is_kernel/module_percpu_address()
module: encapsulate percpu handling better and record percpu_size
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Always build the powerpc perf_arch_fetch_caller_regs version
perf: Always build the stub perf_arch_fetch_caller_regs version
perf, probe-finder: Build fix on Debian
perf/scripts: Tuple was set from long in both branches in python_process_event()
perf: Fix 'perf sched record' deadlock
perf, x86: Fix callgraphs of 32-bit processes on 64-bit kernels
perf, x86: Fix AMD hotplug & constraint initialization
x86: Move notify_cpu_starting() callback to a later stage
x86,kgdb: Always initialize the hw breakpoint attribute
perf: Use hot regs with software sched switch/migrate events
perf: Correctly align perf event tracing buffer
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: set_cpus_allowed_ptr(): Don't use rq->migration_thread after unlock
sched: Fix proc_sched_set_task()
Now that software events use perf_arch_fetch_caller_regs() too, we
need the stub version to be always built in for archs that don't
implement it.
Fixes the following build error in PARISC:
kernel/built-in.o: In function `perf_event_task_sched_out':
(.text.perf_event_task_sched_out+0x54): undefined reference to `perf_arch_fetch_caller_regs'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
* 'kgdb-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: Turn off tracing while in the debugger
kgdb: use atomic_inc and atomic_dec instead of atomic_set
kgdb: eliminate kgdb_wait(), all cpus enter the same way
kgdbts,sh: Add in breakpoint pc offset for superh
kgdb: have ebin2mem call probe_kernel_write once
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Freezer: Fix buggy resume test for tasks frozen with cgroup freezer
Freezer: Only show the state of tasks refusing to freeze
The kernel debugger should turn off kernel tracing any time the
debugger is active and restore it on resume.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Memory barriers should be used for the kgdb cpu synchronization. The
atomic_set() does not imply a memory barrier.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This is a kgdb architectural change to have all the cpus (master or
slave) enter the same function.
A cpu that hits an exception (wants to be the master cpu) will call
kgdb_handle_exception() from the trap handler and then invoke a
kgdb_roundup_cpu() to synchronize the other cpus and bring them into
the kgdb_handle_exception() as well.
A slave cpu will enter kgdb_handle_exception() from the
kgdb_nmicallback() and set the exception state to note that the
processor is a slave.
Previously the salve cpu would have called kgdb_wait(). This change
allows the debug core to change cpus without resuming the system in
order to inspect arch specific cpu information.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Rather than call probe_kernel_write() one byte at a time, process the
whole buffer locally and pass the entire result in one go. This way,
architectures that need to do special handling based on the length can
do so, or we only end up calling memcpy() once.
[sonic.zhang@analog.com: Reported original problem and preliminary patch]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Trivial typo fix. rq->migration_thread can be NULL after
task_rq_unlock(), this is why we have "mt" which should be
used instead.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100330165829.GA18284@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Latencytop clearing sum_exec_runtime via proc_sched_set_task() breaks
task_times(). Other places in kernel use nvcsw and nivcsw, which are
being cleared as well, Clear task statistics only.
Reported-by: Török Edwin <edwintorok@gmail.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1269940193.19286.14.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
perf sched record can deadlock a box should the holder of
handle->data->lock take an interrupt, and then attempt to
acquire an rq lock held by a CPU trying to acquire the
same lock. Disable interrupts.
CPU0 CPU1
sched event with rq->lock held
grab handle->data->lock
spin on handle->data->lock
interrupt
try to grab rq->lock
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1269598293.6174.8.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Scheduler's task migration events don't work because they always
pass NULL regs perf_sw_event(). The event hence gets filtered
in perf_swevent_add().
Scheduler's context switches events use task_pt_regs() to get
the context when the event occured which is a wrong thing to
do as this won't give us the place in the kernel where we went
to sleep but the place where we left userspace. The result is
even more wrong if we switch from a kernel thread.
Use the hot regs snapshot for both events as they belong to the
non-interrupt/exception based events family. Unlike page faults
or so that provide the regs matching the exact origin of the event,
we need to save the current context.
This makes the task migration event working and fix the context
switch callchains and origin ip.
Example: perf record -a -e cs
Before:
10.91% ksoftirqd/0 0 [k] 0000000000000000
|
--- (nil)
perf_callchain
perf_prepare_sample
__perf_event_overflow
perf_swevent_overflow
perf_swevent_add
perf_swevent_ctx_event
do_perf_sw_event
__perf_sw_event
perf_event_task_sched_out
schedule
run_ksoftirqd
kthread
kernel_thread_helper
After:
23.77% hald-addon-stor [kernel.kallsyms] [k] schedule
|
--- schedule
|
|--60.00%-- schedule_timeout
| wait_for_common
| wait_for_completion
| blk_execute_rq
| scsi_execute
| scsi_execute_req
| sr_test_unit_ready
| |
| |--66.67%-- sr_media_change
| | media_changed
| | cdrom_media_changed
| | sr_block_media_changed
| | check_disk_change
| | cdrom_open
v2: Always build perf_arch_fetch_caller_regs() now that software
events need that too. They don't need it from modules, unlike trace
events, so we keep the EXPORT_SYMBOL in trace_event_perf.c
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
The trace event buffer used by perf to record raw sample events
is typed as an array of char and may then not be aligned to 8
by alloc_percpu().
But we need it to be aligned to 8 in sparc64 because we cast
this buffer into a random structure type built by the TRACE_EVENT()
macro to store the traces. So if a random 64 bits field is accessed
inside, it may be not under an expected good alignment.
Use an array of long instead to force the appropriate alignment, and
perform a compile time check to ensure the size in byte of the buffer
is a multiple of sizeof(long) so that its actual size doesn't get
shrinked under us.
This fixes unaligned accesses reported while using perf lock
in sparc 64.
Suggested-by: David Miller <davem@davemloft.net>
Suggested-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Network folks reported that directing all MSI-X vectors of their multi
queue NICs to a single core can cause interrupt stack overflows when
enough interrupts fire at the same time.
This is caused by the fact that we run interrupt handlers by default
with interrupts enabled unless the driver reuqests the interrupt with
the IRQF_DISABLED set. The NIC handlers do not set this flag, so
simultaneous interrupts can nest unlimited and cause the stack
overflow.
The only safe counter measure is to run the interrupt handlers with
interrupts disabled. We can't switch to this mode in general right
now, but it is safe to do so for MSI interrupts.
Force IRQF_DISABLED for MSI interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Linus Torvalds <torvalds@osdl.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: stable@kernel.org
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Do not free zero sized per cpu areas
x86: Make sure free_init_pages() frees pages on page boundary
x86: Make smp_locks end with page alignment
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Fix a memory leak on an OOM condition in prepare_usermodehelper_creds().
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
In some error handling cases the lock is not unlocked. The return is
converted to a goto, to share the unlock at the end of the function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* spin_lock_irq (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
LKML-Reference: <Pine.LNX.4.64.1003291736440.21896@ask.diku.dk>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
# echo 1 > events/enable
# echo global > trace_clock
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:3162 check_flags+0xb2/0x190()
...
---[ end trace 3f86734a89416623 ]---
possible reason: unannotated irqs-on.
...
There's no reason to use the raw_local_irq_save() in trace_clock_global.
The local_irq_save() version is fine, and does not cause the bug in lockdep.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4BA97FA1.7030606@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This avoids an infinite loop in free_early_partial().
Add a warning to free_early_partial() to catch future problems.
-v5: put back start > end back into WARN_ONCE()
-v6: use one line for warning, suggested by Linus
-v7: more tests
-v8: remove the function name as suggested by Johannes
WARN_ONCE() will print out that function name.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Joel Becker <joel.becker@oracle.com>
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1269830604-26214-4-git-send-email-yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CONFIG_SLOW_WORK_PROC was changed to CONFIG_SLOW_WORK_DEBUG, but not in all
instances. Change the remaining instances. This makes the debugfs file
display the time mark and the owner's description again.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise we can get an oops if the user has no get_ref/put_ref
requirement.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lockdep has custom code to check whether a pointer belongs to static
percpu area which is somewhat broken. Implement proper
is_kernel/module_percpu_address() and replace the custom code.
On UP, percpu variables are regular static variables and can't be
distinguished from them. Always return %false on UP.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Better encapsulate module static percpu area handling so that code
outsidef of CONFIG_SMP ifdef doesn't deal with mod->percpu directly
and add mod->percpu_size and record percpu_size in it. Both percpu
fields are compiled out on UP. While at it, mark mod->percpu w/
__percpu.
This is to prepare for is_module_percpu_address().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
x86/PCI: for host bridge address space collisions, show conflicting resource
frv/PCI: remove redundant warnings
x86/PCI: remove redundant warnings
PCI: don't say we claimed a resource if we failed
PCI quirk: Disable MSI on VIA K8T890 systems
PCI quirk: RS780/RS880: work around missing MSI initialization
PCI quirk: only apply CX700 PCI bus parking quirk if external VT6212L is present
PCI: complain about devices that seem to be broken
PCI: print resources consistently with %pR
PCI: make disabled window printk style match the enabled ones
PCI: break out primary/secondary/subordinate for readability
PCI: for address space collisions, show conflicting resource
resources: add interfaces that return conflict information
PCI: cleanup error return for pcix get and set mmrbc functions
PCI: fix access of PCI_X_CMD by pcix get and set mmrbc functions
PCI: kill off pci_register_set_vga_state() symbol export.
PCI: fix return value from pcix_get_max_mmrbc()
When the cgroup freezer is used to freeze tasks we do not want to thaw
those tasks during resume. Currently we test the cgroup freezer
state of the resuming tasks to see if the cgroup is FROZEN. If so
then we don't thaw the task. However, the FREEZING state also indicates
that the task should remain frozen.
This also avoids a problem pointed out by Oren Ladaan: the freezer state
transition from FREEZING to FROZEN is updated lazily when userspace reads
or writes the freezer.state file in the cgroup filesystem. This means that
resume will thaw tasks in cgroups which should be in the FROZEN state if
there is no read/write of the freezer.state file to trigger this
transition before suspend.
NOTE: Another "simple" solution would be to always update the cgroup
freezer state during resume. However it's a bad choice for several reasons:
Updating the cgroup freezer state is somewhat expensive because it requires
walking all the tasks in the cgroup and checking if they are each frozen.
Worse, this could easily make resume run in N^2 time where N is the number
of tasks in the cgroup. Finally, updating the freezer state from this code
path requires trickier locking because of the way locks must be ordered.
Instead of updating the freezer state we rely on the fact that lazy
updates only manage the transition from FREEZING to FROZEN. We know that
a cgroup with the FREEZING state may actually be FROZEN so test for that
state too. This makes sense in the resume path even for partially-frozen
cgroups -- those that really are FREEZING but not FROZEN.
Reported-by: Oren Ladaan <orenl@cs.columbia.edu>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
show_state will dump all tasks state, so if freezer failed to freeze
any task, kernel will dump all tasks state and flood the dmesg log.
This patch makes freezer only show state of tasks refusing to freeze.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
time: Fix accumulation bug triggered by long delay.
posix-cpu-timers: Reset expire cache when no timer is running
timer stats: Fix del_timer_sync() and try_to_del_timer_sync()
clockevents: Sanitize min_delta_ns adjustment and prevent overflows
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ring-buffer: Do 8 byte alignment for 64 bit that can not handle 4 byte align
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Use proper type in sched_getaffinity()
kernel/sched.c: Suppress unused var warning
sched: sched_getaffinity(): Allow less than NR_CPUS length
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Move two IRQ functions from .init.text to .text
genirq: Protect access to irq_desc->action in can_request_irq()
genirq: Prevent oneshot irq thread race
cpuset_mem_spread_node() returns an offline node, and causes an oops.
This patch fixes it by initializing task->mems_allowed to
node_states[N_HIGH_MEMORY], and updating task->mems_allowed when doing
memory hotplug.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Reported-by: Nick Piggin <npiggin@suse.de>
Tested-by: Nick Piggin <npiggin@suse.de>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
