In commit 1b949324 ("RDMA/nes: Fix SFP+ PHY initialization") there is
a mistake in the clean up code that removed port 1 CDR loop filter
settings for 10G cards other than CX4. Put the correct setting back
for appropriate PHY types.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change thermo mitigation code to flip the SerDes1 reference clock to
internal, to match the change in commit a4849fc1 ("RDMA/nes: Add
wide_ppm_offset parm for switch compatibility").
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In error paths where a CQ is not created, pbl is not freeed properly.
In nes_destroy_cq(), add the corresponding check for nescq->mcrqf to
not call nes_free_resource() when it is already done in nes_create_cq().
Signed-off-by: Miroslaw Walukiewicz <miroslaw.walukiewicz@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code incorrectly failed memory registration if the buffer was not
page aligned. Also, the length field is mangled causing the hardware
to think the registration is much larger than it really is.
The fix is to remove the page alignment restriction as well the
incorrect length adjustment. Also make sure that all buffers after
the first start at a page boundary, and all buffers except the last
end on a page boundary.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Initialize pbl_count_256 to 0 to get rid of the warning:
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_reg_mr':
drivers/infiniband/hw/nes/nes_verbs.c:1955: warning: 'pbl_count_256' may be used uninitialized in this function
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
agp: zero pages before sending to userspace
drm: check for minor master before allowing drop master.
drm: set/clear is_master when master changed
drm: clean dirty memory after device release
drm: count reaches -1
* 'for-linus' of git://neil.brown.name/md:
md: support bitmaps on RAID10 arrays larger then 2 terabytes
md: update sync_completed and reshape_position even more often.
md: improve usefulness and accuracy of sysfs file md/sync_completed.
md: allow setting newly added device to 'in_sync' via sysfs.
md: tiny md.h cleanups
notice one system /proc/iomem some entries missed the name for pci_devices
it turns that dev->dev.kobj name is changed after device_add.
for pci code: via acpi_pci_root_driver.ops.add (aka acpi_pci_root_add)
==> pci_acpi_scan_root is used to scan pci bus/device, and at the same
time we read the resource for pci_dev in the pci_read_bases, we have
res->name = pci_name(pci_dev); pci_name is calling dev_name.
later via acpi_pci_root_driver.ops.start (aka acpi_pci_root_start) ==>
pci_bus_add_device to add all pci_dev in kobj tree. pci_bus_add_device
will call device_add.
actually in device_add
/* first, register with generic layer. */
error = kobject_add(&dev->kobj, dev->kobj.parent, "%s", dev_name(dev));
if (error)
goto Error;
will get one new name for that kobj, old name is freed.
[Impact: fix corrupted names in /proc/iomem ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.. and other arrays with components larger than 2 terabytes.
We use a "long" rather than a "sector_t" in part of the bitmap
size calculations, which is sad.
Reported-by: "Mario 'BitKoenig' Holbe" <Mario.Holbe@TU-Ilmenau.DE>
Signed-off-by: NeilBrown <neilb@suse.de>
AGP pages might be mapped into userspace finally, so the pages should be
set to zero before userspace can use it. Otherwise there is potential
information leakage.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When fast user switching a lot eventually we get to the point,
where we were checking for the wrong thing in this function.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The variable is_master is being used to track the drm_file that is currently
master, so its value needs to be updated accordingly when the master is
changed.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In current code we register/unregister connector object by
drm_sysfs_connector_add/remove function.
However under some cases, we need to dynamically register or unregister device
multiple times, so we have to go through register -> unregister ->register
routine.
Because after device_unregister function our memory is dirty, we need to do
clean operation in order to re-register the device, otherwise the system
will crash. The patch intends to clean device after device release.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With a postfix decrement in the test count will reach -1 rather than 0,
subsequent tests fail.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 900af0d973 (PM: Change suspend
code ordering) changed the ordering of suspend code in such a way
that the platform .prepare() callback is now executed after the
device drivers' late suspend callbacks have run. Unfortunately, this
turns out to break ARM platforms that need to talk via I2C to power
control devices during the .prepare() callback.
For this reason introduce two new platform suspend callbacks,
.prepare_late() and .wake(), that will be called just prior to
disabling non-boot CPUs and right after bringing them back on line,
respectively, and use them instead of .prepare() and .finish() for
ACPI suspend. Make the PM core execute the .prepare() and .finish()
platform suspend callbacks where they were executed previously (that
is, right after calling the regular suspend methods provided by
device drivers and right before executing their regular resume
methods, respectively).
It is not necessary to make analogous changes to the hibernation
code and data structures at the moment, because they are only used
by ACPI platforms.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Len Brown <len.brown@intel.com>
This reverts commit 1c55f18717.
Ingo Brueckl was assuming that reverting to 1:1 mapping for chars >= 128
was not useful, but it happens to be: due to the limitations of the
Linux console, when a blind user wants to read BIG5 on it, he has no
other way than loading a font without SFM and let the 1:1 mapping permit
the screen reader to get the BIG5 encoding.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Break out of wait_event_interruptible() if freezing has been requested,
in the vballoon thread. Without this change vballoon refuses to stop and
the system can't suspend.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Fixes guest crash 'lguest: bad read address 0x4800000 len 256'
The new per-cpu allocator ends up handing a non-linear address to
write_gdt_entry. We do __pa() on it, and hand it to the host, which
kills us.
I've long wanted to make the hypercall "LOAD_GDT_ENTRY" to match the IDT
code, but had no pressing reason until now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: lguest@ozlabs.org
Typical message: 'lguest: unhandled trap 6 at 0x418726 (0x0)'
vmlinux guests were broken by 4cd8b5e2a1
'lguest: use KVM hypercalls', which rewrites guest text from kvm hypercalls
to trap 31.
The Launcher mmaps the kernel image. The Guest executes and
immediately faults in the first text page (read-only). Then it hits a
hypercall, and we rewrite that hypercall, causing a copy-on-write.
But the Guest pagetables still refer to the old page: we fault again,
but as Host we see the hypercall already rewritten, and pass the fault
back to the Guest. The Guest hasn't set up an IDT yet, so we kill it.
This doesn't happen with bzImages: they unpack themselves and so the
text pages are already read-write.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Patrick McHardy <kaber@trash.net>
The driver somehow got merged with the initializer for the dma_sff_read_status()
method missing which caused kernel panic on bootup.
This should fix the kernel.org bug #13026...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Freeing non-slab objects is bad and results in an oops. Fix it.
Reported-and-tested-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Theodore Tso <tytso@mit.edu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove uneeded void casts
Signed-off-by: Jack Stone <jwjstone@fastmail.fm>
Cc: jeff@garzik.org
Cc: kernel-janitors@vger.kernel.org
Cc: Jack Stone <jwjstone@fastmail.fm>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE register bits.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The big driver change in 2.4.19-rc1 introduced a regression for many HPT370[A]
chips -- DMA stopped to work completely, only causing endless timeouts...
The culprit has been identified (at last!): it turned to be the code resetting
the DMA state machine before each transfer. Stop doing it now as this counter-
measure has clearly caused more harm than good.
This should fix the kernel.org bug #7703.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] fix build error on drivers/ata/pata_legacy.c
pata_via: Cache and rewrite the device bit
sata_mv: workaround for multi_count errata sata24
sata_mv: tidy up qc->tf usage in qc_prep() functions
fix those errors:
drivers/ata/pata_legacy.c: In function ‘pdc_data_xfer_vlb’:
drivers/ata/pata_legacy.c:289: error: ‘ap’ undeclared (first use in this function)
drivers/ata/pata_legacy.c:289: error: (Each undeclared identifier is reported only once
drivers/ata/pata_legacy.c:289: error: for each function it appears in.)
drivers/ata/pata_legacy.c: At top level:
drivers/ata/pata_legacy.c:869: error: ‘ATA_PFLAG_PIO32_CHANGE’ undeclared here (not in a
+function)
make[2]: *** [drivers/ata/pata_legacy.o] Error 1
make[1]: *** [drivers/ata] Error 2
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some VIA chipsets will reset the DEV bit after IEN changes on ctl. Our
optimised write path avoids doing this but we need to remove the
optimisation on these devices.
[Identified and some original patches proposed by Josehn Chan @ VIA but
discussion then all ground to a halt so given a test case I dug it back out]
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Tested-by: Christoph Bisping (bug #13086)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Workaround for errata SATA#24 in sata_mv.
This errata affects WRITE_MULTI* commands when
the device multi_count produces a DRQ block size >= 4Kbytes.
We work around it here by converting such operations
into ordinary PIO_WRITEs instead.
Note that this might result in a PIO FUA write unavoidably being converted
into a non-FUA write. In practice, any system using FUA is also going to be
using DMA rather than PIO, so this shouldn't affect anyone in the real world.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (43 commits)
staging: slicoss: update README
otus/zdusb.c: additional USB idnetifier
Staging: go7007: fix build issues
Staging: sxg: Fix leaks and checksum errors in transmit code path
Staging: sxg: Fix sleep in atomic context warning while loading driver
Staging: sxg: Use correct queue_id for transmitting non-TCP packets
Staging: sxg: Fire watchdog timer at end of open routine to change the link
Staging: Pohmelfs: Add load balancing between network states with the same priority.
Staging: Pohmelfs: Added IO permissions and priorities.
Staging: Pohmelfs: Added ->show_stats() callback.
Staging: Pohmelfs: Drop ftrans debugging code.
Staging: Pohmelfs: Use wait_on_page_timeout when waiting for remote directory sync instead of hardcoded 25 seconds.
Staging: Pohmelfs: Reduce debugging noise about non-existing objects.
Staging: Pohmelfs: Sync fs before killing it, since dentry cache is shrunk before writeback is invoked via generic_shutdown_super()
Staging: Pohmelfs: Extend remount option.
Staging: Pohmelfs: Set NETFS_INODE_REMOTE_SYNCED and clear NETFS_INODE_OWNED bits in the root inode.
Staging: Pohmelfs: Added 'need_lock' variable into debug print.
Staging: Pohmelfs: Disable read lock in pohmelfs_getattr().
Staging: Pohmelfs: Move parent lock to the place where we really have to send a lookup request to the server.
Staging: pohmelfs: Populate dentry cache when receiving the new readdir entry.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
UIO: fix specific device driver missing statement for depmod
Driver core: remove pr_fmt() from dynamic_dev_dbg() printk
driver core: prevent device_for_each_child from oopsing
dynamic debug: resurrect old pr_debug() semantics as pr_devel()
Driver Core: early platform driver
proc: mounts_poll() make consistent to mdstat_poll
sysfs: sysfs poll keep the poll rule of regular file.
driver core: allow non-root users to listen to uevents
driver core: fix driver_match_device
sysfs: don't use global workqueue in sysfs_schedule_callback()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
WUSB: correct format of wusb_chid sysfs file
WUSB: fix oops when completing URBs for disconnected devices
WUSB: disconnect all devices when stopping a WUSB HCD
USB: whci-hcd: check return value of usb_hcd_link_urb_to_ep()
USB: whci-hcd: provide a endpoint_reset method
USB: add reset endpoint operations
USB device codes for Motorola phone.
usb-storage: fix mistake in Makefile
USB: usb-serial ch341: support for DTR/RTS/CTS
Revert USB: usb-serial ch341: support for DTR/RTS/CTS
USB: musb: fix possible panic while resuming
USB: musb: fix isochronous TXDMA (take 2)
USB: musb: sanitize clearing TXCSR DMA bits (take 2)
USB: musb: bugfixes for multi-packet TXDMA support
USB: musb_host, fix ep0 fifo flushing
USB: usb-storage: augment unusual_devs entry for Simple Tech/Datafab
USB: musb_host, minor enqueue locking fix (v2)
USB: fix oops in cdc-wdm in case of malformed descriptors
USB: qcserial: Add extra device IDs
USB: option: Add ids for D-Link DWM-652 3.5G modem
...
* master.kernel.org:/home/rmk/linux-2.6-arm: (48 commits)
[ARM] S3C24XX: ADC: Check pending queue before freeing adc client
[ARM] S3C: Fix ADC driver sparse warning
[ARM] Osiris: Fix double initialisation in machine block
[ARM] Anubis: Fix sparse warnings for items that should be static
[ARM] JIVE: Fix sparse warnings about items which should be static
[ARM] S3C: Fix sparse warning from missing 's3c_device_hwmon'
[ARM] S3C24XX: Fix sparse error in gpiolib.c
[ARM] 5455/1: Fix IRQ noise from VIC code
[ARM] 5454/1: ep93xx_eth: fix sparse warnings
[ARM] remove .gitignore from include/asm-arm
Update MAINTAINERS
mxc defconfig updates
mx31ads: Mark as having full regulatoion constraints with 1133-EV1 board
mx31ads: Depend on all the WM8350 core dependencies for WM1133-EV1 board
Fix ifdef in plat-mxc/irc.c
MX1ADS: remove I2C ifdefs
qong: remove AIPS[12] mappings from machine-specific iotable
mx31ads: imoux pins should be passed in as unsigned int
MXC: remove orphan imx_init_uart() definition
mx31: pin definition for csi
...
Provide support for WN111v2 USB 802.11n adapter.
Signed-off-by: Daniele Napolitano <dnax88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that TUNER_SET_TYPE_ADDR is gone from the tree, the older code kicks
in and tries to use TUNER_SET_TYPE, which went away a long time ago.
This patch removes all of this logic, as it should not be needed anymore
now, and by doing so, fixes the build.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the transmit function for the following:
* Free XmtCmd in the error code path. This use to leak memory in
error conditions.
* Do pci mapping after the checksum operations are over. They can
reallocate the skb at a different location.
* Fix UDP checksum errors which were seen in wireshark
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave a spinlock before calling request_irq(). request_irq() calls kmalloc
which can sleep. This was generating a warning dump while driver is loaded.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use correct queue_id while transmitting non-TCP packets.
They should always use queue 0.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
The watchdog timer which updates the link status was not fired at the
end of sxg_entry_open(). Add that.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
