This cribs the MIPS plat_smp_ops approach for wrapping up the platform
ops. This will allow for mixing and matching different ops on the same
platform in the future.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a detect_cpu_and_cache_system() -> cpu_probe() rename, tidies
up the unused return value, and stuffs it under __cpuinit in preparation
for CPU hotplug.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change and kills off the unthrottle stub. As the x86
change killed off the generic callback it isn't used anymore anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously the struct module definition was pulled in from other headers,
but we want the reference to be explicit. Fixes up randconfig build
issues.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for hardware-managed IRQ balancing as implemented
by SH-X3 cores (presently only hooked up for SH7786, but can probably be
carried over to other SH-X3 cores, too).
CPUs need to specify their distribution register along with the mask
definitions, as these follow the same format. Peripheral IRQs that don't
opt out of balancing will be automatically distributed at the whim of the
hardware block, while each CPU needs to verify whether it is handling the
IRQ or not, especially before clearing the mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure that the timer IRQs and IPIs aren't enabled for IRQ balancing.
IPIs are disabled as a result of being percpu while the timers simply
disable balancing outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for hardware-assisted userspace irq masking for
special priority levels. Due to the SR.IMASK interactivity, only some
platforms implement this in hardware (including but not limited to
SH-4A interrupt controllers, and ARM-based SH-Mobile CPUs). Each CPU
needs to wire this up on its own, for now only SH7786 is wired up as an
example.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Now with the lookup aliases in place there is no longer any need to
provide the clock string, kill it off for all legacy CPG CPUs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For the CPUs that have not yet been converted off of legacy CPG we
provide some pclk aliases in order to make driver migration easier.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in clkdev lookups for the SH7786 clocks and migrates off of
clock string usage for the TMU clocks.
Previously the TMU clocks were aliased to the peripheral clock, so this
gets the driver actually toggling the proper clocks now as well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For the boot, enable_mmu() is called from setup_arch() but we don't call
setup_arch() for any of the other cpus. So turn on the non-boot cpu's
mmu inside of start_secondary().
I noticed this bug on an SMP board when trying to map I/O memory
(smsc911x registers) into the kernel address space. Since the Address
Translation bit in MMUCR wasn't set, accessing the virtual address where
the smsc911x registers were supposedly mapped actually performed a
physical address access.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use set_cpus_allowed_ptr rather than set_cpus_allowed.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2;
@@
- set_cpus_allowed(E1, cpumask_of_cpu(E2))
+ set_cpus_allowed_ptr(E1, cpumask_of(E2))
@@
expression E;
identifier I;
@@
- set_cpus_allowed(E, I)
+ set_cpus_allowed_ptr(E, &I)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The parent rb_node needs to be initialized to shut up the compiler, even
though we're unlikely to ever hit this issue at run time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
select_idle_routine() and register_sh_pmu() both needed their annotations
fixed up to silence section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
interruptible_sleep_on() is referenced for use in the mid_sched macro
which is not used anywhere. Remove reference and macro as well as the
comment which appears to belong with them.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (35 commits)
perf: Fix unexported generic perf_arch_fetch_caller_regs
perf record: Don't try to find buildids in a zero sized file
perf: export perf_trace_regs and perf_arch_fetch_caller_regs
perf, x86: Fix hw_perf_enable() event assignment
perf, ppc: Fix compile error due to new cpu notifiers
perf: Make the install relative to DESTDIR if specified
kprobes: Calculate the index correctly when freeing the out-of-line execution slot
perf tools: Fix sparse CPU numbering related bugs
perf_event: Fix oops triggered by cpu offline/online
perf: Drop the obsolete profile naming for trace events
perf: Take a hot regs snapshot for trace events
perf: Introduce new perf_fetch_caller_regs() for hot regs snapshot
perf/x86-64: Use frame pointer to walk on irq and process stacks
lockdep: Move lock events under lockdep recursion protection
perf report: Print the map table just after samples for which no map was found
perf report: Add multiple event support
perf session: Change perf_session post processing functions to take histogram tree
perf session: Add storage for seperating event types in report
perf session: Change add_hist_entry to take the tree root instead of session
perf record: Add ID and to recorded event data when recording multiple events
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
Add generic implementations of the old and really old uname system calls.
Note that sh only implements sys_olduname but not sys_oldolduname, but I'm
not going to bother with another ifdef for that special case.
m32r implemented an old uname but never wired it up, so kill it, too.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the ipc demultiplexer syscall. Except for
s390 and sparc64 all implementations of the sys_ipc are nearly identical.
There are slight differences in the types of the parameters, where mips
and powerpc as the only 64-bit architectures with sys_ipc use unsigned
long for the "third" argument as it gets casted to a pointer later, while
it traditionally is an "int" like most other paramters. frv goes even
further and uses unsigned long for all parameters execept for "ptr" which
is a pointer type everywhere. The change from int to unsigned long for
"third" and back to "int" for the others on frv should be fine due to the
in-register calling conventions for syscalls (we already had a similar
issue with the generic sys_ptrace), but I'd prefer to have the arch
maintainers looks over this in details.
Except for that h8300, m68k and m68knommu lack an impplementation of the
semtimedop sub call which this patch adds, and various architectures have
gets used - at least on i386 it seems superflous as the compat code on
x86-64 and ia64 doesn't even bother to implement it.
[akpm@linux-foundation.org: add sys_ipc to sys_ni.c]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the hw_perf_event_*() hotplug hooks in favour of per PMU hotplug
notifiers. This has the advantage of reducing the static weak interface
as well as exposing all hotplug actions to the PMU.
Use this to fix x86 hotplug usage where we did things in ONLINE which
should have been done in UP_PREPARE or STARTING.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: paulus@samba.org
Cc: eranian@google.com
Cc: robert.richter@amd.com
Cc: fweisbec@gmail.com
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
LKML-Reference: <20100305154128.736225361@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes up some of the I/D/F clock ambiguity in the sh-sci driver.
The interface clock in most cases just wraps back to the peripheral
clock, while the function clock wraps in to the MSTP bits. As the logic
was somewhat inverted, this cleans that up, and also enables all CPUs
with SCI MSTP bits to match function clocks through clkdev lookup.
As a result, this gets rid of the clk string abuse on the sh side, and
the clock string will be killed off once the ARM code has had a chance to
sync up. This also enables MSTP gating on CPUs like 7786 which had never
wired it up before. Impacted CPUs are primarily all SH-Mobiles, SH7785,
and SH7786.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that dev_name() can be used early, we no longer require a static
string. Kill off all of the superfluous timer names.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
early platform devices and the like may need to set up clock aliases,
which require an allocation at a time well before the slab allocators
are available. The clock framework comes up after bootmem, so using
bootmem as a fallback should be sufficient.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rolls in the remainder of the clkdev API bits from the ARM tree.
This can more or less be used verbatim, so we just copy it over and nuke
our local version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the sh architecture to use the generic
read_persistent_clock and update_persistent_clock interfaces, reducing
the amount of arch specific code we have to maintain, and allowing for
further cleanups in the future.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the case of NUMA emulation when in range PPNs are being used for
secondary nodes, we need to make sure that the PMB has a mapping for it
before setting up the pgdat. This prevents the MMU from resetting.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Separate SH DMA headers into ones, commonly used by both drivers, and ones,
specific to each of them. This will make the future development of the
dmaengine driver easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The shdma dmaengine driver currently uses numerous macros to support various
platforms, selected by ifdef's. Convert it to use platform device resources and
lists of channel descriptors to specify register locations, interrupt numbers
and other system-specific configuration variants. Unavoidably, we have to
simultaneously convert all shdma users to provide those resources.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is required to use the SIU ASoC driver on sh7722 systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change 84d7109267
("hw-breakpoints: Accept breakpoints on NULL address") and restores the
previous expected ptrace behaviour.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (28 commits)
ftrace: Add function names to dangling } in function graph tracer
tracing: Simplify memory recycle of trace_define_field
tracing: Remove unnecessary variable in print_graph_return
tracing: Fix typo of info text in trace_kprobe.c
tracing: Fix typo in prof_sysexit_enable()
tracing: Remove CONFIG_TRACE_POWER from kernel config
tracing: Fix ftrace_event_call alignment for use with gcc 4.5
ftrace: Remove memory barriers from NMI code when not needed
tracing/kprobes: Add short documentation for HAVE_REGS_AND_STACK_ACCESS_API
s390: Add pt_regs register and stack access API
tracing/kprobes: Make Kconfig dependencies generic
tracing: Unify arch_syscall_addr() implementations
tracing: Add notrace to TRACE_EVENT implementation functions
ftrace: Allow to remove a single function from function graph filter
tracing: Add correct/incorrect to sort keys for branch annotation output
tracing: Simplify test for function_graph tracing start point
tracing: Drop the tr check from the graph tracing path
tracing: Add stack dump to trace_printk if stacktrace option is set
tracing: Use appropriate perl constructs in recordmcount.pl
tracing: optimize recordmcount.pl for offsets-handling
...
Add code to save/restore registers during
R-standby sleep on SH-Mobile processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7724 processor code to always enable vpu_clk.
On the Ecovec board, set the vpu_clk to 166 Mhz.
The 166MHz setting results in a divide-by-6 setup for
vpu_clk and improves the VPU performance compared to the
power-on-reset/bootloader configuration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a ->kick() callback to clk_div4_table
and ties it into sh_clk_div4_set_rate(). A sh7724
specific kick function is also added that updates the
KICK bit whenever div4 clocks in FRQCRA and FRQCRB
have been set. Allows us to set the VPU clock.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces struct clk_div4_table. The structure
will be used to keep div4 specific data, and is with this
patch replacing the struct clk_div_mult_table pointer arg
used by the sh_clk_div4_register() functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure the div4 bitfield is shifted according
to the enable_bit value in sh_clk_div4_set_rate().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a bit of rework for the PMB code, which permits us to
kill off the legacy PMB mode completely. Rather than trusting the boot
loader to do the right thing, we do a quick verification of the PMB
contents to determine whether to have the kernel setup the initial
mappings or whether it needs to mangle them later on instead.
If we're booting from legacy mappings, the kernel will now take control
of them and make them match the kernel's initial mapping configuration.
This is accomplished by breaking the initialization phase out in to
multiple steps: synchronization, merging, and resizing. With the recent
rework, the synchronization code establishes page links for compound
mappings already, so we build on top of this for promoting mappings and
reclaiming unused slots.
At the same time, the changes introduced for the uncached helpers also
permit us to dynamically resize the uncached mapping without any
particular headaches. The smallest page size is more than sufficient for
mapping all of kernel text, and as we're careful not to jump to any far
off locations in the setup code the mapping can safely be resized
regardless of whether we are executing from it or not.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Most implementations of arch_syscall_addr() are the same, so create a
default version in common code and move the one piece that differs (the
syscall table) to asm/syscall.h. New arch ports don't have to waste
time copying & pasting this simple function.
The s390/sparc versions need to be different, so document why.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1264498803-17278-1-git-send-email-vapier@gentoo.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
This adds some helper routines for uncached mapping support. This
simplifies some of the cases where we need to check the uncached mapping
boundaries in addition to giving us a centralized location for building
more complex manipulation on top of.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some overdue cleanup of the PMB code, killing off unused functionality
and duplication sprinkled about the tree.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both the store queue API and the PMB remapping take unsigned long for
their pgprot flags, which cuts off the extended protection bits. In the
case of the PMB this isn't really a problem since the cache attribute
bits that we care about are all in the lower 32-bits, but we do it just
to be safe. The store queue remapping on the other hand depends on the
extended prot bits for enabling userspace access to the mappings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7723 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7722 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
vmemmap and the vmsplit code amongst others need to be able to take page
faults much earlier than trap_init() time, so move this in to the early
CPU initialization. VBR setup for secondary CPUs is already handled
through start_secondary(), so we only need to do this for the boot CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The __va()/__pa() offsets and the boot memory offsets are consistent for
all PMB users, so there is no need to special case these for legacy PMB.
Kill the special casing off and depend on CONFIG_PMB across the board.
This also fixes up yet another addressing bug for sh64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7724 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the parisc change to ensure that tracehook_signal_handler()
is aware of when we are single-stepping in order to ptrace_notify()
appropriately. While this was implemented for 32-bit SH, sh64 neglected
to make use of TIF_SINGLESTEP when it was folded in with the 32-bit code,
resulting in ptrace_notify() never being called.
As sh64 uses all of the other abstractions already, this simply plugs in
the thread flag in the appropriate enable/disable paths and fixes up the
tracehook notification accordingly. With this in place, sh64 is brought
in line with what 32-bit is already doing.
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The linker script offsets were broken by the recent 29/32-bit
integration, so this fixes it up for sh64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break out sh7723 div4 clocks for SIU and IRDA as
reparent / enable clocks. Similar to the SIU clock
patch for sh7722 by Guennadi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7724 INTC table
and update the SDHI platform data for Ecovec24,
KFR2R09 and MS7724SE.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7723 INTC table
and update the SDHI platform data for AP325.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7722 INTC table
and update the SDHI platform data for Migo-R.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the DWARF unwinder is being used to provide perf callstacks
unwinding speed is an issue. It is no longer being used in exceptional
circumstances where we don't care about runtime performance, e.g. when
panicing, so it makes sense improve performance is possible.
With this patch I saw a 42% improvement in unwind time when calling
return_address(1). Greater improvements will be seen as the number of
levels unwound increases as each unwind is now cheaper.
Note that insertion time has doubled but that's just the price we pay
for keeping the trees balanced. However, this is a one-time cost for
kernel boot/module load and so the improvements in lookup time dominate
the extra time we spend keeping the trees balanced.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's no need to setup the frame pointer again in
call_handle_tlbmiss. The frame pointer will already have been setup in
handle_interrupt.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Unfortunately, due to poor DWARF info in current toolchains, unwinding
through interrutps cannot be done reliably. The problem is that the
DWARF info for function epilogues is wrong.
Take this standard epilogue sequence,
80003cc4: e3 6f mov r14,r15
80003cc6: 26 4f lds.l @r15+,pr
80003cc8: f6 6e mov.l @r15+,r14
<---- interrupt here
80003cca: f6 6b mov.l @r15+,r11
80003ccc: f6 6a mov.l @r15+,r10
80003cce: f6 69 mov.l @r15+,r9
80003cd0: 0b 00 rts
If we take an interrupt at the highlighted point, the DWARF info will
bogusly claim that the return address can be found at some offset from
the frame pointer, even though the frame pointer was just restored. The
worst part is if the unwinder finds a text address at the bogus stack
address - unwinding will continue, for a bit, until it finally comes
across an unexpected address on the stack and blows up.
The only solution is to stop unwinding once we've calculated the
function that was executing when the interrupt occurred. This PC can be
easily calculated from pt_regs->pc.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In order to allow the DWARF unwinder to unwind through exceptions we
need to setup the frame pointer register (r14).
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The address that ret_from_exception and ret_from_irq will return to is
found in the stack slot for SPC, not PR. This error was causing the
DWARF unwinder to pick up the wrong return address on the stack and then
unwind using the unwind tables for the wrong function.
While I'm here I might as well add CFI annotations for the other
registers since they could be useful when unwinding.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This improves power management for the SIUA controller on sh7722. Similar
patches might be desired for other SIU-enabled SH platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
'flush_old_exec()' is the point of no return when doing an execve(), and
it is pretty badly misnamed. It doesn't just flush the old executable
environment, it also starts up the new one.
Which is very inconvenient for things like setting up the new
personality, because we want the new personality to affect the starting
of the new environment, but at the same time we do _not_ want the new
personality to take effect if flushing the old one fails.
As a result, the x86-64 '32-bit' personality is actually done using this
insane "I'm going to change the ABI, but I haven't done it yet" bit
(TIF_ABI_PENDING), with SET_PERSONALITY() not actually setting the
personality, but just the "pending" bit, so that "flush_thread()" can do
the actual personality magic.
This patch in no way changes any of that insanity, but it does split the
'flush_old_exec()' function up into a preparatory part that can fail
(still called flush_old_exec()), and a new part that will actually set
up the new exec environment (setup_new_exec()). All callers are changed
to trivially comply with the new world order.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running perf across all cpus with backtracing (-a -g), sometimes we
get samples without associated backtraces:
23.44% init [kernel] [k] restore
11.46% init eeba0c [k] 0x00000000eeba0c
6.77% swapper [kernel] [k] .perf_ctx_adjust_freq
5.73% init [kernel] [k] .__trace_hcall_entry
4.69% perf libc-2.9.so [.] 0x0000000006bb8c
|
|--11.11%-- 0xfffa941bbbc
It turns out the backtrace code has a check for the idle task and the IP
sampling does not. This creates problems when profiling an interrupt
heavy workload (in my case 10Gbit ethernet) since we get no backtraces
for interrupts received while idle (ie most of the workload).
Right now x86 and sh check that current is not NULL, which should never
happen so remove that too.
Idle task's exclusion must be performed from the core code, on top
of perf_event_attr:exclude_idle.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
LKML-Reference: <20100118054707.GT12666@kryten>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Presently trapped I/O is only registered if it's not explicitly disabled
for the platforms that select it openly. From the fault path this runs
through an address lookup before figuring out that nothing matches and
falls back through the error path, but we can forego the lookup
completely by testing if it's been explicitly disabled. This provides a
measurable speedup for things like qemu that rely on runtime disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The old ctrl in/out routines are non-portable and unsuitable for
cross-platform use. While drivers/sh has already been sanitized, there
is still quite a lot of code that is not. This converts the arch/sh/ bits
over, which permits us to flag the routines as deprecated whilst still
building with -Werror for the architecture code, and to ensure that
future users are not added.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that cached_to_uncached works as advertized in 32-bit mode and we're
never going to be able to map < 16MB anyways, there's no need for the
special uncached section. Kill it off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a variable for tracking the uncached mapping size, and uses
it for pretty printing the uncached lowmem range. Beyond this, we'll also
be building on top of this for figuring out from where the remainder of
P2 becomes usable when constructing unrelated mappings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This effectively neutralizes P2 by getting rid of P1 identity mapping
for all available memory and instead only establishes a single unbuffered
PMB entry (16MB -- the smallest available) that covers the kernel.
As using segmentation for abusing caching attributes in drivers is no
longer supported (and there are no drivers that can be enabled in 32-bit
mode that do this), this provides us with all of the uncached access
needs by the kernel itself.
Drivers and their ilk need to specify their caching attributes when
remapping through page tables, as usual.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the cached/uncached mapping setup is duplicated for each size, and
also misses out on the 16MB case. Rather than duplicating the same iter
code for that we just consolidate it in to a helper macro that builds an
iter for each size. The 16MB case is then trivially bolted on at the end.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a machine_ops-based reboot interface loosely cloned from
x86, and converts the native sh32 and sh64 cases over to it.
Necessary both for tying in SMP support and also enabling platforms like
SDK7786 to add support for their microcontroller-based power managers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Usually we can look to the CVR to work out whether we have an FPU or not.
Unfortunately not all parts comply with this, so just set the flag
manually for all SH-4 parts and clear it on the only SH-4 that doesn't
have one (SH4-501).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Implement .set_rate() for all SH "div4 clocks," .enable(), .disable(), and
.set_parent() for those, that support them. This allows, among other uses,
reparenting of SIU clocks to the external source, and enabling and
disabling of the IrDA clock on sh7722.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rewrites the SH7786 clock framework support completely. It's
reworked to provide all of the DIV4 and MSTP function clocks. This brings
it in line with the current clock framework code and lets us drop SH7786
from the list of CPUs that require legacy CPG handling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh64 on the other hand provides both direct broken out syscalls as well
as socketcall access. As there are binaries that use both socketcall has
to stay around. The current ABI prefers direct syscalls.
It was pointed out that when sys_recvmmsg was added in, sys_accept4 was
overlooked. This takes care of wiring it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh32 at the moment only uses sys_socketcall to reach these, so unwire
recvmmsg for now. While we're at it, add it to the ignore list, as per
the s390 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This updates the sh64 processor info with the sh32 changes in order to
tie in to the generic task_xstate management code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tosses in a local_irq_enable()/disable() pair around the init_fpu()
callsite in the FPU state restore exception handler. Fixes up a slab BUG
triggered by making a slab cache allocation that can sleep whilst
irqs_disabled(). This follows the behaviour undertaken by the x86
implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
More and more boards are going to start shipping that boot with the MMU
in 32BIT mode by default. Previously we relied on the bootloader to
setup PMB mappings for use by the kernel but we also need to cater for
boards whose bootloaders don't set them up.
If CONFIG_PMB_LEGACY is not enabled we have full control over our PMB
mappings and can compress our address space. Usually, the distance
between the the cached and uncached mappings of RAM is always 512MB,
however we can compress the distance to be the amount of RAM on the
board.
pmb_init() now becomes much simpler. It no longer has to calculate any
mappings, it just has to synchronise the software PMB table with the
hardware.
Tested on SDK7786 and SH7785LCR.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some devices need to be ioremap'd and accessed very early in the boot
process. It is not possible to use the standard ioremap() function in
this case because that requires kmalloc()'ing some virtual address space
and kmalloc() may not be available so early in boot.
This patch provides fixmap mappings that allow physical address ranges
to be remapped into the kernel address space during the early boot
stages.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Presently the secondary CPU entry point is only aimed at 29bit phys mode,
causing it to point to a stray virtual address in 32bit mode. Fix it up
after consulting with our shiny new __in_29bit_mode().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This introduces some much overdue chainsawing of the fixed PMB support.
fixed PMB was introduced initially to work around the fact that dynamic
PMB mode was relatively broken, though they were never intended to
converge. The main areas where there are differences are whether the
system is booted in 29-bit mode or 32-bit mode, and whether legacy
mappings are to be preserved. Any system booting in true 32-bit mode will
not care about legacy mappings, so these are roughly decoupled.
Regardless of the entry point, PMB and 32BIT are directly related as far
as the kernel is concerned, so we also switch back to having one select
the other.
With legacy mappings iterated through and applied in the initialization
path it's now possible to finally merge the two implementations and
permit dynamic remapping overtop of remaining entries regardless of
whether boot mappings are crafted by hand or inherited from the boot
loader.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The mass produced cuts use an updated PVR value, add them to the list.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 xstate changes and implements a task_xstate slab
cache that is dynamically sized to match one of hard FP/soft FP/FPU-less.
This also tidies up and consolidates some of the SH-2A/SH-4 FPU
fragmentation. Now fpu state restorers are commonly defined, with the
init_fpu()/fpu_init() mess reworked to follow the x86 convention.
The fpu_init() register initialization has been replaced by xstate setup
followed by writing out to hardware via the standard restore path.
As init_fpu() now performs a slab allocation a secondary lighterweight
restorer is also introduced for the context switch.
In the future the DSP state will be rolled in here, too.
More work remains for math emulation and the SH-5 FPU, which presently
uses its own special (UP-only) interfaces.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this has a BUG_ON() for failure cases, as powerpc does. Switch
this over to a SLAB_PANIC instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the thread_info allocators are special cased, depending on
THREAD_SHIFT < PAGE_SHIFT. This provides a sensible definition for them
regardless of configuration, in preparation for extended CPU state.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
start_thread() will become a bit heavier with the xstate freeing to be
added in, so move it out-of-line in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some VBR sanity checks in the sh_bios code to ensure that the
BIOS VBR is in range before blindly trapping in to it. This permits
boards with varying boot loader configurations to always leave support
for sh-bios enabled and it will just be disabled at run-time if not
found.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out the unaligned access counters and userspace bits in to
their own generic interface, which will allow them to be wired up on sh64
too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the sh-sci earlyprintk is taken care of by the sh-sci driver
directly, there's no longer any reason for having a split-out
early_printk framework. sh_bios is the only other thing that uses it, so
we just migrate the leftovers in to there. As it's possible to have
multiple early_param()'s for the same string, there's not much point in
having this split out anymore anyways, particularly since the sh_bios
dependencies are still special-cased within sh-sci itself.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was conditionalized on CONFIG_EARLY_PRINTK, which has subsequently
gone away. Now that the serial driver always supports the early console,
make sure we always establish the mapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the VBR handling out of the main trap handling code and in to
the sh-bios helper code. A couple of accessors are added in order to
permit other kernel code to get at the VBR value for state save/restore
paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the next big chunk of hw_breakpoint support. This decouples
the SH-4A support from the core and moves it out in to its own stub,
following many of the conventions established with the perf events
layering.
In addition to extending SH-4A support to encapsulate the remainder
of the UBC channels, clock framework support for handling the UBC
interface clock is added as well, allowing for dynamic clock gating.
This also fixes up a regression introduced by the SIGTRAP handling that
broke the ksym_tracer, to the extent that the current support works well
with all of the ksym_tracer/ptrace/kgdb. The kprobes singlestep code will
follow in turn.
With this in place, the remaining UBC variants (SH-2A and SH-4) can now
be trivially plugged in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the hw_breakpoint code is the primary notifier dispatch for
breakpoint traps, although it's only UBC traps that are of particular
interest there. This patches in a check to allow non-UBC generated
breakpoints to pass through down the remainder of the notifier chain,
giving things like kgdb a chance at getting notified.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The event callback handling has been removed in favour of going through a
generic event handler to handle overflows. Follows the x86 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We don't actually require this in the cpu_relax() polling case, so just
cuddle these around the sleeping version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
After the recent FPU optimisation commit the signature of save_fpu()
changed. "regs" wasn't used in the implementation of save_fpu() anyway.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now when the sh-sci driver can do early serial output,
get rid of the old duplicated code. This patch is V2 and
removes support for "earlyprintk=serial" together with
the following kconfig options:
CONFIG_EARLY_SCIF_CONSOLE
CONFIG_EARLY_SCIF_CONSOLE_PORT
CONFIG_EARLY_PRINTK
With this patch applied "earlyprintk=" support is always
built-in the SuperH kernel. For this to work the serial
driver must have early platform support and in the case
of sh-sci the serial console needs to be enabled:
CONFIG_SERIAL_SH_SCI_CONSOLE=y
So after enabling the SuperH SCI console kconfig option
you also need to point out port using the kernel command
line: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Remember that clocks may be disabled by the boot loader
so you may have to do some board specific static clock
setup before earlyprintk will work on your platform.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh5 scif serial port platform
data from a shared platform device to one platform
device per port. Also, move the serial port to the list
of early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
All sh4a except SuperH Mobile processors are modified by
this patch.
While at it, sh7757 gets early platform device support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Only sh4a SuperH Mobile processors are modified by this
patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
While at it, get rid of the R2D ifdef in the processor
code and adjust the defconfigs to use ttySC1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh3 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh2a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh2 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is V2 of early serial console support for the sh-sci
driver. The early serial console is using early platform
devices and "earlyprintk". To use this feature the early
platform devices must be broken out to one device per port
and the desired port should be selected on the kernel command
line like: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Presently there are a couple of paths in to the alignment handler, where
only the address error path presently quiets the notificiation messages
based on the configuration settings. We carry over the notification level
tests to the default alignment handler itself incase so that they behave
uniformly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
New helper - sys_mmap_pgoff(); switch syscalls to using it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The stub already existed in the _64 syscall table, but was lacking a
__NR_recvmmsg definition, while it was absent entirely for _32 variants.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
The macro container_of from kernel.h performs the same
pointer arithmetic operation.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression mptr;
expression member;
@@
- (void *)((char *)mptr - offsetof(T, member))
+ container_of(mptr, T, member)
// </smpl>
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
Conflict between FPU thread flag migration and debug
thread flag addition.
Conflicts:
arch/sh/include/asm/thread_info.h
arch/sh/include/asm/ubc.h
arch/sh/kernel/process_32.c
This adds preliminary support for the SH-4A UBC to the hw-breakpoints API.
Presently only a single channel is implemented, and the ptrace interface
still needs to be converted. This is the first step to cleaning up the
long-standing UBC mess, making the UBC more generally accessible, and
finally making it SMP safe.
An additional abstraction will be layered on top of this as with the perf
events code to permit the various CPU families to wire up support for
their own specific UBCs, as many variations exist.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that associative cache writes are no longer needed by the SH-4/SH-4A
cache flush code, associative write support can be explicitly disabled
for all SH-4A parts. This makes any associative write throw an exception,
as this behaviour can not be assumed to exist on future parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Runtime PM code for SuperH Mobile
to allow drivers to have NULL as pm or callback value.
With this in place there is no need for no-op functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This file breaks out the SuperH PFC code from
arch/sh/kernel/gpio.c + arch/sh/include/asm/gpio.h
to drivers/sh/pfc.c + include/linux/sh_pfc.h.
Similar to the INTC stuff. The non-SuperH specific
file location makes it possible to share the code
between multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7724 code to save and restore CPG state during
R-standby. Only CPG registers IRDACLKCR and SPUCLKCR
require software save and restore.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A number of small optimisations to FPU handling, in particular:
- move the task USEDFPU flag from the thread_info flags field (which
is accessed asynchronously to the thread) to a new status field,
which is only accessed by the thread itself. This allows locking to
be removed in most cases, or can be reduced to a preempt_lock().
This mimics the i386 behaviour.
- move the modification of regs->sr and thread_info->status flags out
of save_fpu() to __unlazy_fpu(). This gives the compiler a better
chance to optimise things, as well as making save_fpu() symmetrical
with restore_fpu() and init_fpu().
- implement prepare_to_copy(), so that when creating a thread, we can
unlazy the FPU prior to copying the thread data structures.
Also make sure that the FPU is disabled while in the kernel, in
particular while booting, and for newly created kernel threads,
In a very artificial benchmark, the execution time for 2500000
context switches was reduced from 50 to 45 seconds.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh port of the sLeAZY-fpu feature currently implemented for some architectures
such us i386.
Right now the SH kernel has a 100% lazy fpu behaviour.
This is of course great for applications that have very sporadic or no FPU use.
However for very frequent FPU users... you take an extra trap every context
switch.
The patch below adds a simple heuristic to this code: after 5 consecutive
context switches of FPU use, the lazy behavior is disabled and the context
gets restored every context switch.
After 256 switches, this is reset and the 100% lazy behavior is returned.
Tests with LMbench showed no regression.
I saw a little improvement due to the prefetching (~2%).
The tests below also show that, with this sLeazy patch, indeed,
the number of FPU exceptions is reduced.
To test this. I hacked the lat_ctx LMBench to use the FPU a little more.
sLeasy implementation
===========================================
switch_to calls | 79326
sleasy calls | 42577
do_fpu_state_restore calls| 59232
restore_fpu calls | 59032
Exceptions: 0x800 (FPU disabled ): 16604
100% Leazy (default implementation)
===========================================
switch_to calls | 79690
do_fpu_state_restore calls | 53299
restore_fpu calls | 53101
Exceptions: 0x800 (FPU disabled ): 53273
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
Now that sys_sysctl is a generic wrapper around /proc/sys .ctl_name
and .strategy members of sysctl tables are dead code. Remove them.
Also add an C99 named initializer to the child member of unaligned_root
to prevent chaos as the ctl_table definition changes over time.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
sh64 doesn't use GENERIC_BUG, which presently causes the handle_BUG()
code to blow up. Fix up the dependencies and get it all building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the build and behaviour for various configurations. Namely
the CONFIG_32BIT cases where legacy mappings do not exist, as well as the
sh64 build.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The dwarf unwinder presently attempts to provide a sane PC value if none
is provided, however the logic is broken and cases where a previous valid
dwarf frame exists along with a bogus PC value can still proceed. This
fixes up the test and prevents the unwinder from blowing up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements preliminary support for perf callchains (at the moment
only the kernel side is implemented). The actual implementation itself is
just a simple wrapper around the unwinder API, which allows for callchain
generation with or without the dwarf unwinder.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wanted by the SPU2 UIO driver, which really ought to be handling this
itself. Default enable it for now, until the driver gets a bit more
intelligent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
'config' can be unintialized, and although it's not really an error, it
still manages to trigger the -Werror with certain toolchains. Initialize
it early to shut up gcc.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7724 code to save and restore RWDT state during
R-standby. Without this patch the watchdog will generate
a reset shortly after resuming from R-standby.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Different CPUs will have different starting vectors, with varying
amounts of reserved or unusable vector space prior to the first slot.
This introduces a legacy vector reservation system that inserts itself in
between the CPU vector map registration and the platform specific IRQ
setup. This works fine in practice as the only new vectors that boards
need to establish on their own should be dynamically allocated rather
than arbitrarily assigned. As a plus, this also makes all of the
converted platforms sparseirq ready.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add R-standby specific bits to the SuperH Mobile sleep code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use RSMEM instead of ILMEM for sleep mode code storage on SH7724.
This allows us to use R-standby mode on SH7724.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add MMU and cache handling functionality to the SuperH Mobile
sleep code. The MMU and cache registers are saved and restored.
The MMU is disabled and the cache is flushed and disabled before
entering sleep modes if the SUSP_SH_MMU flag is set. This flag
should be set in the case of R-standby and most likely for future
U-standby support as well.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add code to keep track of supported sleep modes. This to
only export cpuidle modes that are backed by board support
code. Also, do not allow suspend-to-ram if sdram board code
is missing.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the SuperH Mobile sleep code from including
board specific code to allowing each board to provide
pre/post code snippets. These snippets should contain
sdram management code to enter and leave self-refresh.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add code to allow boards registering self-contained
functions for going to/from self-refresh. At this
point the board code is unused. When all supported
boards have been converted then the new sleep code
will make use of these functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make use of the recently added notifier chains for sh7724
r-standby register save/restore handling. At this point
only the BSC and INTC are handled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds atomic notifier chains for pre/post
sleep events. Useful for cpu code and boards that
need to save and restore register state before and
after entering a sleep mode.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
num_events should be compared > MAX_HWEVENTS and not >=. The latter was
used as a debugging test which accidentally slipped in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in preliminary support for the SH-4A performance counters.
Presently only the first 2 counters are supported, as these are the ones
of the most interest to the perf tool and end users. Counter chaining is
not presently handled, so these are simply implemented as 32-bit
counters.
This also establishes a perf event support framework for other hardware
counters, which the existing SH-4 oprofile code will migrate over to as
the SH-4A support evolves.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many of these symbols went away completely, or we just never cared about
them in the first place. Trim the exports down to the essential set.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were previously hidden in sh_ksyms_32, despite also being needed
for sh64 now that the cache.c code is shared.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Leaving this configurable caused more trouble than it was ever worth, so
just make it explicit. Boards that are verified one way or the other can
fix up their selects accordingly. We presently default to non-coherent
for most platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that SH's irqflags functions are out of line it becomes necessary to
mark them as "notrace" so that we don't try to trace them.
[ Do the same for irq_64.c -- PFM. ]
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This unbreaks kexec support. Without this fix all
cases of kexec fails since __pa() does not behave
like PHYSADDR(). The downside is that we also kill
the code blocking users running old kexec-tools.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_FUNCTION_GRAPH_TRACER is enabled the function graph tracer
may patch return addresses on the stack with the address of
return_to_handler(). This really confuses the DWARF unwinder because it
will try find the caller of return_to_handler(), not the caller of the
real return address.
So teach the DWARF unwinder how to find the real return address whenever
it encounters return_to_handler().
This patch does not cope very well when multiple return addresses on the
stack have been patched. To make it work properly it would require state
to track how many return_to_handler()'s have been seen so that we'd know
where to look in current->curr_ret_stack[]. So for now, instead of
trying to handle this, just moan if more than one return address on the
stack has been patched.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds an __irq_entry annotation for do_IRQ() so that the IRQ
annotation in the function graph tracer works as advertized. We already
have the IRQENTRY section wired up, so this is just a trivial addition
to actually make use of it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the current dma_alloc/free_coherent() calls to a generic
variant and plugs them in for the nommu default. Other variants can
override the defaults in the dma mapping ops directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SCIF2 and the FPU exceptions happen to share vector numbers, one in
EXPEVT and the other in INTEVT. This is a violation of the interface and
should have never made it in to silicon. On top of that, the demux hack
that was added for special dispatch is rather error prone, and introduces
more problems than it solves. Kill all of it off, and just refuse to deal
with SCIF2 outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This simplifies the irqflags support by switching over to the asm-generic
version. The necessary support functions are brought out-of-line for both
SHcompact and SHmedia instruction sets.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code was added for some ancient SH-4 solution engines with peculiar
boot ROMs that did silly things to the UBC MSTP bits. None of these have
been in the wild for years, and these days the clock framework wraps up
the MSTP bits, meaning that the UBC code is one of the few interfaces
that is stomping MSTP bits underneath the clock framework. At this point
the risks far outweigh any benefit this code provided, so just kill it
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables SCHED_MC support for SH-X3 multi-cores. Presently this is
just a simple wrapper around the possible map, but this allows for
tying in support for some of the more exotic NUMA clusters where we can
actually do something with the topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the case where need_resched() is set in between the cpu_idle() and
pm_idle() calls we were missing an else case for just re-enabling local
IRQs and bailing out. This was noticed by the irqs_disabled() warning,
even though IRQs were being re-enabled elsewhere.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change and moves check_pgt_cache() up under the
!need_resched() tight loop, rather than simply calling in to it when
exiting idle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of chainsawing of the idle loop code to get light sleep
working on SMP. Previously this was forcing secondary CPUs in to sleep
mode with them not coming back if they didn't have their own local
timers. Given that we use clockevents broadcasting by default, the CPU
managing the clockevents can't have IRQs disabled before entering its
sleep state.
This unfortunately leaves us with the age-old need_resched() race in
between local_irq_enable() and cpu_sleep(), but at present this is
unavoidable. After some more experimentation it may be possible to layer
on SR.BL bit manipulation over top of this scheme to inhibit the race
condition, but given the current potential for missing wakeups, this is
left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the secondary CPUs are forced in to light sleep mode, but we were
missing the same initialization for the boot CPU. This resulted in
inconsistent sleep modes depending on which CPU we were on, confusing the
idle loop when not polling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in support for NMI counting per-CPU via irq_cpustat_t.
Modelled after the x86 implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace TIF_RESTORE_SIGMASK with TS_RESTORE_SIGMASK and define our own
set_restore_sigmask() function. This saves the costly SMP-safe set_bit
operation, which we do not need for the sigmask flag since TIF_SIGPENDING
always has to be set too.
Based on the x86 and powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The resume_userspace path had TRACE_IRQS_OFF written incorrectly and so
never handled the transition properly. This was fixed once before but
seems to have made it back in the tree. Fix it for good.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This only needs to flush the return code via the legacy path, and just
invalidates uselessly otherwise. This makes the behaviour consistent for
all of the trampoline setup paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The secondary CPU info was seeing corrupted results due to not entering
all of the setup paths taken by the boot CPU. So we just memcpy() the
boot cpu data over directly, and then fix up the per-CPU bits.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We do not want to use smp_processor_id() from these paths, as they trip
preempt BUGs. Switch the test over to the boot cpu directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Secondary CPUs already take care of the D-cache bits through the common
cache initialization path, and the only thing that is necessary after
twiddling around with stack_start is ensuring that the I-cache changes
are visible (particularly since this tends to be the only part lacking
coherency).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This cribs the x86 implementation of ftrace_nmi_enter() and friends to
make ftrace_modify_code() NMI safe, particularly on SMP configurations.
For additional notes on the problems involved, see the comment below
ftrace_call_replace().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds return_address.c to the -pg exclusion list, as this is the
building block for CALLER_ADDRx we do not want to profile this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Meaning receive multiple messages, reducing the number of syscalls and
net stack entry/exit operations.
Next patches will introduce mechanisms where protocols that want to
optimize this operation will provide an unlocked_recvmsg operation.
This takes into account comments made by:
. Paul Moore: sock_recvmsg is called only for the first datagram,
sock_recvmsg_nosec is used for the rest.
. Caitlin Bestler: recvmmsg now has a struct timespec timeout, that
works in the same fashion as the ppoll one.
If the underlying protocol returns a datagram with MSG_OOB set, this
will make recvmmsg return right away with as many datagrams (+ the OOB
one) it has received so far.
. Rémi Denis-Courmont & Steven Whitehouse: If we receive N < vlen
datagrams and then recvmsg returns an error, recvmmsg will return
the successfully received datagrams, store the error and return it
in the next call.
This paves the way for a subsequent optimization, sk_prot->unlocked_recvmsg,
where we will be able to acquire the lock only at batch start and end, not at
every underlying recvmsg call.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables us to build the dwarf unwinder both with modules enabled and
disabled in addition to reducing code size in the latter case. The
helpers are also consolidated, and modified to resemble the BUG module
helpers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out the unwinder implementation and adds a new
return_address() abstraction modelled after the ARM code. The DWARF
unwinder is tied in to this, returning NULL otherwise in the case of
being unable to support arbitrary depths.
This enables us to get correct behaviour with the unwinder enabled,
as well as disabling the arbitrary depth support when frame pointers are
enabled, as arbitrary depths with __builtin_return_address() are not
supported regardless.
With this abstraction it's also possible to layer on a simplified
implementation with frame pointers in the event that the unwinder isn't
enabled, although this is left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Sync up with latest core changes in the syscalls tracing area:
- tracing: Map syscall name to number (syscall_name_to_nr())
- tracing: Call arch_init_ftrace_syscalls at boot
- tracing: add support tracepoint ids (set_syscall_{enter,exit}_id())
Taken from the s390 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change, as SH had all of the same issues:
Make die() better match x86:
- add printing of the last accessed sysfs file
- ensure console_verbose() is called under the lock
- ensure we panic outside of oops_exit()
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Originally, dwarf_unwind_stack() was a recursive function and it seems
that some of the old comments were never updated.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
If we broke out of the while (1) loop because the return address of
"frame" was zero, then "frame" needs to be free'd before we return.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Pass a module's .eh_frame section to the DWARF unwinder at module load
time so that the section's FDEs and CIEs can be registered with the
DWARF unwinder. This allows us to unwind the stack through module code
when generating backtraces.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
In the multi-evt conversion for the SH-X3 proto CPU, IRLs were dropped
down to a single unique masking source, which ended up blowing up on
ILSEL-based IRQs which have special semantics that otherwise confuse the
intc code. While this does result in intc spewing about not having a
unique masking source, we don't really care.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The initialisation process differs for CONFIG_PMB and for
CONFIG_PMB_FIXED. For CONFIG_PMB_FIXED we need to register the PMB
entries that were allocated by the bootloader.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's no need to export the internal PMB functions for allocating,
freeing and modifying PMB entries, etc. This way we can restrict the
interface for PMB.
Also remove the static from pmb_init() so that we have more freedom in
setting up the initial PMB entries and turning on MMU 32bit mode.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CONFIG_PMB will eventually allow the MMU to be switched between 29-bit
and 32-bit mode dynamically at runtime.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace the use of PHYSADDR() with __pa(). PHYSADDR() is based on the
idea that all addresses in P1SEG are untranslated, so we can access an
address's physical page as an offset from P1SEG. This doesn't work for
CONFIG_PMB/CONFIG_PMB_FIXED because pages in P1SEG and P2SEG are used
for PMB mappings and so can be translated to any physical address.
Likewise, replace a P1SEGADDR() use with virt_to_phys().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
