The SMS_SYSCONFIG register gets reset in off mode, added a
save/restore mechanism for that.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Initialize SDRC_POWER to a known-good setting when the kernel boots.
Necessary since some bootloaders don't initialize SDRC_POWER properly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Separate SDRC code common to OMAP2/3 from mach-omap2/sdrc2xxx.c to
mach-omap2/sdrc.c. Rename the OMAP2xxx-specific functions to use an
'omap2xxx' prefix rather than an 'omap2' prefix, and use "sdrc" in the
function names rather than "memory." Mark several functions
as static that should not be used outside the sdrc2xxx.c file.
linux-omap source commit is bf1612b9d8d29379558500cd5de9ae0367c41fc4.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
