The pac7302 and pac7311 driver still contains some comments from before
they were separated, such as marking certain functions 7302 or 7311 only,
with the new split drivers these make no sense, remove them.
Also removed the empty/unused sd_stop0 function from pac7311.c
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow users of gspca/autogain_functions.h to declare which of the autogain
algoritms they are going to use. This allows us to remove the hacks from
drivers which don't use coarse_grained_expo_autogain.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exposure of Omnivision sensors is defined by the registers 07, 10 and 04.
This patch updates the registers 10 and 04 before using the registers 2d
and 2e (dummy lines).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Telling the bridge to update the sensor when setting the exposure or the gain
is not needed when the image transfer is not started.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c interface speed was set to 400 Kb/s while it is 100 Kb/s
for most sensors.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The table did not contain the sensor mt9vprb.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error messages in stable kernel releases must be output by 'pr_err'.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Jean-Francois Moine <moinejf@free.fr>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bridge register 1061 may take only the values 01 (stop) or 03 (start).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG compression may be adjusted from the packet fill ratio and from
the flag 'USB FIFO full' returned in each frame.
The code is adapted from the one in gspca sonixj and uses a workqueue.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new functions i2c_w1_buf() and i2c_w2_buf() handle the write loops.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG compression quality was hardcoded to 95%. This value was too big,
raising often buffer overflows.
This quality is now 80% by default and is settable.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The reset of the Omnivision sensors takes a long time (200ms).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frame header was checked on packets of size 64 bytes only, while the webcams
may put a frame header at the beginning of bigger packets.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The line defining the value of the register 08 for the sensor cs2102k was
commented by error in commit 30c73d46.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds brightness control to the OmniVision 5621 sensor.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adapted from Sylwester's patch proposed on 2012/02/22.
The JPEG compression control does not work with the autoquality done for the
sensors hv7131r and pas202b.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exposure was not set when autogain was set.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The setexposure added in commit 590f216806 works only for the sensor hv7131r,
but it is called for all sensors when changing the autogain.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bridge register 11 reports the current transfer status.
This value is used to know about a possible overflow and to adjust
the transfer parameters (registers 07 and 08).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the bridge register 08 defines the JPEG compression quality,
it must be changed on JPEG quality change and also, the decompression
tables must be adjusted when the register varies.
[mchehab@redhat.com: replace a // comment by a /* */ one]
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The auto gain uses the knee algorithm.
Adding the setexposure control function forced to:
- rename of the previous function setexposure
- add a specific auto setting function
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_jcomp control is rarely used and its main information,
the JPEG quality, may be found in the images.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG header is always the same, so, it does not need to be rebuild
each time a new frame is received.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (655 commits)
[media] revert patch: HDIC HD29L2 DMB-TH USB2.0 reference design driver
mb86a20s: Add a few more register settings at the init seq
mb86a20s: Group registers into the same line
[media] [PATCH] don't reset the delivery system on DTV_CLEAR
[media] [BUG] it913x-fe fix typo error making SNR levels unstable
[media] cx23885: Query the CX25840 during enum_input for status
[media] cx25840: Add support for g_input_status
[media] rc-videomate-m1f.c Rename to match remote controler name
[media] drivers: media: au0828: Fix dependency for VIDEO_AU0828
[media] convert drivers/media/* to use module_platform_driver()
[media] drivers: video: cx231xx: Fix dependency for VIDEO_CX231XX_DVB
[media] Exynos4 JPEG codec v4l2 driver
[media] doc: v4l: selection: choose pixels as units for selection rectangles
[media] v4l: s5p-tv: mixer: fix setup of VP scaling
[media] v4l: s5p-tv: mixer: add support for selection API
[media] v4l: emulate old crop API using extended crop/compose API
[media] doc: v4l: add documentation for selection API
[media] doc: v4l: add binary images for selection API
[media] v4l: add support for selection api
[media] hd29l2: fix review findings
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Somehow the code has ended up assuming 1400 packets/sec which of course
is wrong for usb1 devices like the ov511 cameras. usb1 only does 1000
(isoc) packets / sec.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This got broken by some gscpa core fixes, this patch restores the proper
min/max values for these controls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Written by Theodore Kilgore
With minor changes by Hans de Goede:
-Code style fixes
-Correct the verbose level on various PDEBUG messages
-Make error messages use pr_err instead of PDEBUG
-Document the jl20 pixel format
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.2': (83 commits)
Linux 3.2
minixfs: misplaced checks lead to dentry leak
ptrace: ensure JOBCTL_STOP_SIGMASK is not zero after detach
ptrace: partially fix the do_wait(WEXITED) vs EXIT_DEAD->EXIT_ZOMBIE race
Revert "rtc: Expire alarms after the time is set."
[CIFS] default ntlmv2 for cifs mount delayed to 3.3
cifs: fix bad buffer length check in coalesce_t2
Revert "rtc: Disable the alarm in the hardware"
hung_task: fix false positive during vfork
security: Fix security_old_inode_init_security() when CONFIG_SECURITY is not set
fix CAN MAINTAINERS SCM tree type
mwifiex: fix crash during simultaneous scan and connect
b43: fix regression in PIO case
ath9k: Fix kernel panic in AR2427 in AP mode
CAN MAINTAINERS update
net: fsl: fec: fix build for mx23-only kernel
sch_qfq: fix overflow in qfq_update_start()
drm/radeon/kms/atom: fix possible segfault in pm setup
gspca: Fix falling back to lower isoc alt settings
futex: Fix uninterruptible loop due to gate_area
...
When using the SN9C20X_I420 fmt the sn9c20x needs more bandwidth
than our regular bandwidth calculations reserve.
This patch adds a sd_isoc_init function, which forces the use of a specific
altsetting when using the SN9C20X_I420 fmt.
This fixes the bottom 10-30% of the image getting corrupted when using
the SN9C20X_I420 fmt (which is the default fmt).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some cameras will pretty much entirely fill all the image buffers all the
time even though they are using compression.
This patch adds a flag to sd_desc, which drivers for such cameras can set.
When this flag is set the bandwidth calculation code will no longer
assume that the image buffer size is a worst case and less bandwidth than
imagebufsize * fps will be used on average.
This patch sets this new flag for 3 drivers:
* For spca561 (for rev12a cameras) and nw80x cams as these simply don't work
when given less bandwidth than imagebufsize * fps.
* For sn9c20x cameras, because these show severy jpeg artifacts when
given less bandwidth than imagebufsize * fps and since these are usb2
cameras there is plenty bandwidth anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Quoting from the official usb 20 spec:
"5.6.4 Isochronous Transfer Bus Access Constraints
Isochronous transfers can only be used by full-speed and high-speed devices."
This means that for code paths which are isoc mode only, we don't need to
check for the device being low speed, simplifying the code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check dev->actconfig rather than dev->config when checking various
configuration things. dev->config points to the array of configs for the
device so dev->config->foo boils down to dev->config[0].foo and the first
config is not necessarily always the active config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In case we ever get sub drivers which do 7.5 fps and express this as
15 / 2 fps.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The calculated bandwidth should not be multiplied by the interval, but be
divided by it. Also bInterbval should be interpreted as a power of 2
for isochronous endpoints.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After the "gspca: Fix bulk mode cameras no longer working (regression fix)"
patch build_ep_tb is no longer being called for bulk endpoints.
This patch renames build_ep_tb to build_isoc_ep_tb to make clear it should
only be called for isoc mode cameras.
This patch also:
- drops the no longer needed xfer parameter
- removes a check for bulk mode from the build_isoc_ep_tb code
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having:
- a mean image size of 0.375 time the max compressed image size and
- a frame rate of 30 fps for small images or with USB 2.0/3.0
seems more realistic and gives less image freezes.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This path add support to "OmniVision Technologies, Inc. VEHO Filmscanner".
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current gspca core code has a regression where it no longer properly
falls back to lower alt settings when there is not enough bandwidth.
This causes many iso based usb-1 cameras to not work when plugged into a
usb2 hub or a sandybridge chipset motherboard!
This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 &
vicam cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 & vicam
cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adjustment of the colors by the po2030n is finer than by the bridge controls.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'open-drain' mode was not reset when starting the webcams.
This problem was introduced by commit 0e4d413af1 and
its exact effects are unknown.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the alternate settings are now sorted in gspca main,
the variable 'nbalt' is no more useful.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The alternate settings are now sorted in gspca main, so the flag
'reverse_alts' is no more useful.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This converts the drivers in drivers/media/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Frank Zago <frank@zago.net>
Cc: Olivier Lorin <o.lorin@laposte.net>
Cc: Erik Andren <erik.andren@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Brian Johnson <brijohn@gmail.com>
Cc: Leandro Costantino <lcostantino@gmail.com>
Cc: Antoine Jacquet <royale@zerezo.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Florian Mickler <florian@mickler.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Michael Krufky <mkrufky@kernellabs.com>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Florent Audebert <florent.audebert@anevia.com>
Cc: Sam Doshi <sam@metal-fish.co.uk>
Cc: Manu Abraham <manu@linuxtv.org>
Cc: Olivier Grenie <olivier.grenie@dibcom.fr>
Cc: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Cc: "Igor M. Liplianin" <liplianin@me.by>
Cc: Derek Kelly <user.vdr@gmail.com>
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: "André Weidemann" <Andre.Weidemann@web.de>
Cc: Martin Wilks <m.wilks@technisat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jose Alberto Reguero <jareguero@telefonica.net>
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Rafi Rubin <rafi@seas.upenn.edu>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Paul Bender <pebender@gmail.com>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: "Márcio A Alves" <froooozen@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Chris Rankin <rankincj@yahoo.com>
Cc: Lee Jones <lee.jones@canonical.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Dean Anderson <linux-dev@sensoray.com>
Cc: Pete Eberlein <pete@sensoray.com>
Cc: Arvydas Sidorenko <asido4@gmail.com>
Cc: Andrea Anacleto <andreaanacleto@libero.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As the choice of the alternate setting has been enhanced in the gspca main,
forcing its number here is no more useful.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG quality was guessed as around 82%. Information in ms-win drivers
says it should be 85%.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams ask for a greater time to start.
This patch increases the delay before timeout error on capture start.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is based on Anders Blomdell's source proposed in april 2009.
It has been extended to handle the tp6810 bridge and the soi763a sensor.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adapted from a patch from Sarah Sharp (2010/05/03).
The xHCD handler checks the USB bandwidth on usb_set_interface()
instead of on usb_submit_urb().
Now, the same treatment is applied in case of error of both functions.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously image transfer used to use the highest altsetting, which, most of
the time, took the whole USB bandwidth.
Now, the altsetting is chosen according to an estimation of the bandwidth
needed for image transfer.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sd_isoc_init() did only a set interface which is done in gspca main.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In vidioc_enum_fmt_vid_cap, the 'compressed' flag was set from the
pixelformat, and all pixelformats were not treated.
Now, images are told as compressed when the image size is smaller than
its number of pixels.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For USB speeds different of 'low', the bInterval value is logarithmic.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam is build from an Omnivision test kit which contains a OV538 bridge
and a OV9712 sensor.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The variable gspca_debug is defined and settable in gspca main.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The contrast was too low. Higher values are better.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The images are clearer with a lower bridge clock.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The list of the webcams which have LED inversion was rebuild scanning
ms-win .inf files.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add pr_fmt.
Convert usb style logging macros to pr_<level>.
Remove now unused old usb style logging macros.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add pr_fmt and convert usb style logging macro uses to pr_<level>.
Coalesce format strings.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usage of these flags has been deprecated for nearly 4 years by:
commit f77bf01425
Author: Sam Ravnborg <sam@neptun.(none)>
Date: Mon Oct 15 22:25:06 2007 +0200
kbuild: introduce ccflags-y, asflags-y and ldflags-y
Moreover, these flags (at least EXTRA_CFLAGS) have been documented for command
line use. By default, gmake(1) do not override command line setting, so this is
likely to result in build failure or unexpected behavior.
Replace their usage by Kbuild's `{as,cc,ld}flags-y'.
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
