Remove the PS3 workaround needed to support sparsemem SPU mappings.
The SPU mappings no longer use sparsemem, so this workaround is no
longer needed.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 logical performance monitor (lpm) device driver.
The PS3's LV1 hypervisor provides a Logical Performance Monitor that
abstracts the Cell processor's performance monitor features for use
by guest operating systems.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 logical performance monitor device support to the
PS3 system-bus and platform device registration routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup coding errors in arch/powerpc/platforms/ps3/repository.c as
reported by sparse and checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3: Add repository polling loop to work around timing bug
On some firmware versions (e.g. 1.90), the storage device may not show up
in the repository immediately after receiving the notification message.
Add a small polling loop to make sure we don't miss it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PS3 hypervisor has a storage device notification mechanism to wait
until a storage device is ready. Unfortunately the storage device
probing code used this mechanism in an incorrect way, needing a
polling loop and handling of devices that are not yet ready.
This change corrects this by:
- First waiting for the reception of an asynchronous notification
that a new storage device became ready,
- Then looking up the storage device in the device repository.
On shutdown, the storage probe thread is stopped and the storage
notification device is closed using a reboot notifier.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The storage probe feature of the PS3 hypervisor returns device IDs. Add
the corresponding repository routine ps3_repository_find_device_by_id()
which can be used to retrieve the device info from the repository.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the PS3 bus_id and dev_id from type unsigned int to u64. These
IDs are 64-bit in the repository, and the special storage notification
device has a device ID of ULONG_MAX.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevents miscellaneous users from declaring it locally.
Signed-off-by: Jon Loeliger <jdl@freecale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Call of_platform_bus_probe() on the MPC8641 HPCN, similar to what is
done for other platforms.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the MPC8610 HPCD files to support the audio driver. Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
IPIC is not just for 83xx anymore so make it a separate config option.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add in missing of_node_put() after cpm2_pic_init(). This and other coding
style cleanups as suggested by Stephen Rothwell.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob
and perform the actual upload. Fully define 'struct rsp' in immap_qe.h to
include the actual RISC Special Registers. Added description of a new
QE firmware node to booting-without-of.txt.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:
- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
and if there is a PCI bus node defined in the device tree.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
mpc5200 platform code defines a bunch of map functions which duplicate the
functionality of of_iomap(). Remove them and use of_iomap() instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch moves a generic pci init code from lite5200
platform file to a common mpc52xx_setup_pci() routine
and adds additional compatibility property verification.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Define MPC52xx specific device id list, add new
'fsl,lpb' compatible id for LocalPlus Bus.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
xlate_iomm_address() really wants the ds_addr to pass to the HV, so store
that value (instead of the BAR number) when we allocate the device bars.
This is not a fast path, so we can look up the device_node property
there instead of using the bussubno field of the pci_dn.
The other user of iseries_ds_addr() was already scanning the device tree,
so looking up a property will not slow it down any more.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Similar to of_find_compatible_node(), of_find_matching_node() and
for_each_matching_node() allow you to iterate over the device tree
looking for specific nodes, except that they take of_device_id
tables instead of strings.
This also moves of_match_node() from driver/of/device.c to
driver/of/base.c to colocate it with the of_find_matching_node which
depends on it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move electra-ide glue over to the new pata_of_platform framework, and
add the quirks needed to that driver.
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 473980a993 added a call to clear
the SLB shadow buffer before registering it. Unfortunately this means
that we clear out the entries that slb_initialize has previously set in
there. On POWER6, the hypervisor uses the SLB shadow buffer when doing
partition switches, and that means that after the next partition switch,
each non-boot CPU has no SLB entries to map the kernel text and data,
which causes it to crash.
This fixes it by reverting most of 473980a9 and instead clearing the
3rd entry explicitly in slb_initialize. This fixes the problem that
473980a9 was trying to solve, but without breaking POWER6.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Before we register the SLB shadow buffer, we need to invalidate the
entries in the buffer, otherwise we can end up stale entries from when
we previously offlined the CPU.
This does this invalidate as well as unregistering the buffer with
PHYP before we offline the cpu. Tested and fixes crashes seen on
970MP (thanks to tonyb) and POWER5.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Includes both flavors of plb, opb, dcr, and a pseudo 'compound' bus
for representing compound peripherals containing more than one logical
device.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The logic that checks to see if a machine check is caused by an NMI will
always match when NMI hasn't been initialized, since the mpic routine
will return NO_IRQ (and that's what the nmi_virq value is as well).
Signed-off-by: Olof Johansson <olof@lixom.net>
