While the PC speaker is wired up to the i8254 there is more to the i8254
than just the PC speaker so this code was getting in the way under its
current name.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To support multiple TC microthreads acting as "CPUs" within a VPE,
VPE-wide interrupt mask bits must be specially manipulated during
interrupt handling. To support legacy drivers and interrupt controller
management code, SMTC has a "backstop" to track and if necessary restore
the interrupt mask. This has some performance impact on interrupt service
overhead. Disable it only if you know what you are doing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add mips common support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are no I/O ports on the DECstation whatsoever in any configuration
as neither the CPU nor the peripheral buses used have a concept of such.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It has some hackish code and it odd DMA results in the need to support
old features in kernel code.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Those boards do not need CONFIG_ISA if the ne driver could be
selectable without it. Disable it and update a defconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch has removed 2 select entries for VR41xx.
These entries are selected in arch/mips/vr41xx/Kconfig.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has merged GT64111 PCI routines and GT64120 PCI_0 routines.
GT64111 PCI is almost the same as GT64120's PCI_0.
This patch don't change GT64120 PCI routines.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So until MIPS_MT_SMTC_INSTANT_REPLAY has been rewritten to solve this
issue, don't allow selecting it with PREEMPT.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Might be useful for SMP debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[Rewritten Kconfig bits to deal better fit in the usual pattern of doing
things - Ralf]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A defconfig file and the 10 lines of code (including comments ...) that
are rotting since lmo commit 6516a42dc8b40c6c00010346dd51496125b16644
don't quite make proper support, so let's trash it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick). This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds trivial support for SMARTMIPS extension. This extension
is currently implemented by 4KS[CD] CPUs.
Basically it saves/restores ACX register, which is part of the SMARTMIPS
ASE, when needed. This patch does *not* add any support for Smartmips MMU
features.
Futhermore this patch does not add explicit support for 4KS[CD] CPUs since
they are respectively mips32 and mips32r2 compliant. So with the current
processor configuration, a platform that has such CPUs needs to select
both configs:
CPU_HAS_SMARTMIPS
SYS_HAS_CPU_MIPS32_R[12]
This is due to the processor configuration which is mixing up all the
architecture variants and the processor types.
The drawback of this, is that we currently pass '-march=mips32' option to
gcc when building a kernel instead of '-march=4ksc' for 4KSC case. This
can lead to a kernel image a little bit bigger than required.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Platforms will now have to supply a function dma_device_is_coherent which
returns if a particular device participates in the coherence domain. For
most platforms this function will always return 0 or 1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] signal: do not inline handle_signal()
[MIPS] signal: do not use save_static_function() anymore
[MIPS] signal32: no need to save c0_status register in setup_sigcontext32()
[MIPS] signal32: reduce {setup,restore}_sigcontext32 sizes
[MIPS] signal: factorize debug code
[MIPS] signal: test return value of install_sigtramp()
[MIPS] signal32: remove duplicate code
[MIPS] signal: clean up sigframe structure
[MIPS] signal: do not inline functions in signal-common.h
[MIPS] signals: reduce {setup,restore}_sigcontext sizes
[MIPS] Fix warning in get_user when fetching pointer object from userspace.
[MIPS] Fix eth2 platform device id for jaguar_atx and ocelot_3 platforms
[MIPS] JMR3927 and RBTX49x7 support little endian
[MIPS] RBTX49x7: declare prom_getcmdline()
[MIPS] RTLX: Sprinkle device model code into code to make udev happier.
[MIPS] VPE: Sprinkle device model code into code to make udev happier.
