Remove w1 comments from crc16.h and move
specific constants into w1_ds2433.c where they are used.
Replace %d with %zd.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: I messed up the baud_base for custom baud rate support in
2.6.13. The attached one-liner patch fixes it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern sent me this patch. It goes on top of the patch the adds
mon_dmapeek:
http://ftp.kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/gregkh-04-usb/usb-usbmon-dma-areas.patch
Please be warned about ordering requirements or the build may fail.
Actually, mon_dmapeek is generic enough to support SETUP packets too.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the long standing schedule with interrupts off problem
of the uss720 driver. The problem is caused by the parport layer calling
the save and restore methods within a write_lock_irqsave guarded region.
The fix is to issue the control transaction requests required by save
and restore asynchronously.
Signed-off-by: Thomas Sailer, <sailer@ife.ee.ethz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern wrote:
> If the device sometimes reports the correct values, then you should
> include NEED_OVERRIDE flag to prevent messages about unnecessary
> overrides showing up in the system log. Also, if bInterfaceSubclass
> is correct and only bInterfaceProtocol is wrong, then the entry should
> say US_SC_DEVICE instead of US_SC_SCSI.
Fair points, thanks.
When connected over USB2, this device reports a nonsense
bInterfaceProtocol value 6 and doesn't work with usb-storage. When
connected over USB1, the device reports the correct bInterfaceProtocol
value 0x50 (bulk) and works with no problems.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds entries for several USB floppies that need
the US_FL_SINGLE_LUN flag. These were reported by
Sebastian Kapfer <sebastian_kapfer@gmx.net> and Olaf Hering
<olh@suse.de>, with rediffing and cleaning from me.
Reported-by: Sebastian Kapfer <sebastian_kapfer@gmx.net>
Reported-by: Olaf Hering <olh@suse.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The stick replies to the door lock commands with a check condition (e.g.
FAIL status in a normal bulk CSW), but the subsequent REQUEST SENSE
returns all-zero sense. The situation is documented in our Bugzilla,
including usbmon traces.
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=162559
The error is purely cosmetic, data integrity is not in danger.
But I thought we might as well do it. It looks nicer that way.
I discussed this with Phil and he told me to submit directly.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is patch as550 from Alan Stern.
Apparently someone changed the SCSI core so that it no longer holds the
host lock when doing a device or bus reset. usb-storage was updated at
the time, but the change was done carelessly. Some of the code depends
on that lock being held.
This patch reintroduces the host lock where needed and tries to clarify
the comments explaining why the lock is necessary. It also moves the
code that clears the TIMED_OUT and ABORTING bitflags so that it executes
as soon as the timed-out command has completed (and while the host lock
is held).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This appears to help some folk, please merge.
This patch relaxes reset timings. There are some reports that it
helps make enumeration work better on some high speed devices.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID and vendor ID for a Nokia CA-42 USB cable
to the list of devices handled by the pl2303 driver. The patch is
against 2.6.13.
Signed-off-by: Robert Spanton <rds204@zepler.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that it's in use on other boards, a bug in the original code needs fixing.
There is no need for the PXA27x OHCI to set usb power during init, since
the hub driver in usbcore handles that. Those platform-specific power
control functions are also incorrect, and should therefore be removed.
Add a check to clear the OTG pin hold bit until such times OTG is
properly implemented.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some OHCI implementations have differences in the way the NDP register
(in roothub_a) reports the number of ports present. This patch allows the
platform specific code to optionally supply the number of ports. The
driver just reads the value at init (if not supplied) instead of reading
it every time its needed (except for an AMD756 bug workaround).
It also sets the value correctly for the ARM pxa27x architecture.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evidently there are some boards which care a lot about this, but
as a rule it's been hard to notice.
OHCI_INTR_RD wasn't always cleared in the ohci irq handler. On some
systems this means certain remote wakeup scenarios could seem to hang
(in an interrupt storm, RD never clearing).
From: "William Morrow" <William.Morrow@amd.com>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch fixes an "Invalid argument" error returned by a write to an
endpoint-file after reopening it in the gadgetfs module in the kernel
2.6.12.
This was testet only with dummy_hcd module!
Signed-off-by: Pavol Kurina <kurina@gmx.net>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Routine cases like handoff-to-companion shouldn't trigger diagnostics.
This gets rid of some recently added log spamming. It's routine for
hub_port_wait_reset() to return -ENOTCONN to indicate handoff from
highspeed hubs to companions, so an error message is incorrect.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NVidia reports (via Mark Overby) that some of their EHCI controllers
don't like certain data structure addresses beyond the 2GB mark.
He provided an earlier version of this patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One change may improve some S1 or S3 resume cases, and the other
seems mostly to explain some strange state "lsusb" would show.
Two fixes:
- On resume, don't think about resuming any unpowered port, or
resetting any port with OWNER set to the OHCI/UHCI companion.
This will make some S1 and S3 resume scenarios work better.
- PORT_CSC was not being cleared correctly in ehci_hub_status_data.
This was visible at least through current versions of "lsusb",
and might have caused some other hub related strangeness.
The fix addresses all three write-to-clear bits, using the same
approach that UHCI happens to use: a mask of bits that are
cleared in most writes to that port status register.
Original patch seems to have been from from William.Morrow@amd.com
and this version (from David) finishes the write-to-clear changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Three new device IDs for CP2101 USB to UART Bridge
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as558) removes from the UHCI driver a kernel timer used for
checking Full Speed Bandwidth Reclamation (FSBR). The checking can be
done during normal root-hub polling; it doesn't need a separate timer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as549) introduces two small changes in the HCD glue layer.
The first simply removes a redundant test. The second allows root-hub
polling to continue for a single iteration after a host controller dies;
this is needed for the patch that follows.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.
This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
* appletouch is a full kernel driver, no userspace program is necessary
* appletouch can be interfaced with the synaptics X11 driver[2], in order
to have touchpad acceleration, scrolling, two/three finger tap, etc.
This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.
Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
here is a new and extended version of the sisusbvga (previously: sisusb)
driver. The patch is against 2.6.13 and updates the driver to version 0.0.8.
Additions include complete VGA/EGA text console support and a build-in
display mode infrastructure for userland applications that don't know
about the graphics internals.
Fixes include some BE/LE issues and a get/put_dev bug in the previous
version.
Other changes include a change of the module name from "sisusb" to
"sisusbvga". The previous one was too generic IMHO.
Please note that the patch also affects the Makefile in
drivers/video/console as the driver requires the VGA 8x16 font in case
the text console part is selected.
Heavily tested, as usual. Please apply.
One thing though: I already prepared for removal of the "mode" field and
the changed "name" field in the usb_class_driver structure. This will
perhaps need some refinement depending on whether you/Linus merge the
respective core changes before or after 2.6.14.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove w1 comments from crc16.h and move specific constants into
w1_ds2433.c where they are used.
Replace %d with %zd.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean out trailing whitespace caused by not-so-great editor since it
generates a lot of problems with editors configured to automatically
strip whitespace.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attached patch removes #ifdef CONFIG_WATCHDOG_NOWAYOUT mess and
replaces it with common define in linux/watchdog.h.
Signed-Off-By: Wim Van Sebroeck <wim@iguana.be>
In a project for my company I've needed to use the watchdog device in a
PCM-5335 SBC from AAEON. The watchdog timer is from a Winbond's SuperIO
chip, the W83977F.
I've made this driver based on two others already on the kernel tree,
the w83877f_wdt and the wdt977.
Signed-off-by: Jose Goncalves <jose.goncalves@inov.pt>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reported by: Manuel Lauss <mano@roarinelk.homelinux.net>
He was getting random initial video modes depending on the kernel
configuration. His option line includes 'extvga'.
The i810fb documentation describes the option 'extvga', however the
driver accepts 'ext_vga'. Besides 'extvga' being ignored by i810fb,
it also confuses the option parser of i810fb and assigns 'extvga' to
'mode_option'. This leads to an incorrect video mode at boot time.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If i810fb successfully probed for the EDID, it will disregard the
boot option parameters 'xres' and 'yres'. Fix this regression.
Excellent testing done by Manuel Lauss <mano@roarinelk.homelinux.net>.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the FEC ethernet driver of the Freescale 523x processor
family to the FEC header definitions.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should not call mtd_put_device() in the uclinux MTD map driver.
Also consistently use phys/virt fields of maps map_info struct,
instead of mixing it with map_priv_1.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the new Freescale 523x processor family to ColdFire
serial driver. Also set different default baud rate for MOD5272
board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few improvements to the Freescale/ColdFire FEC driver:
. some formatting cleanups
. add support for the FEC device in the ColdFire 523x processor family
. add support for MAC address setting on MOD5272 and M5272C3 boards
. don't re-read the PHY status register many times
. ack status interrupt before reading status register
. move printing init message to after full init (so that the
ethX name is filled out for printing)
Some parts of this patch submitted by Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add configuration support for the FEC ethernet controller in the
Freescale 523x processor family. Also add and option to configure
the second FEC controller on some Freescale processors.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kernel connector - new userspace <-> kernel space easy to use
communication module which implements easy to use bidirectional
message bus using netlink as it's backend. Connector was created to
eliminate complex skb handling both in send and receive message bus
direction.
Connector driver adds possibility to connect various agents using as
one of it's backends netlink based network. One must register
callback and identifier. When driver receives special netlink message
with appropriate identifier, appropriate callback will be called.
From the userspace point of view it's quite straightforward:
socket();
bind();
send();
recv();
But if kernelspace want to use full power of such connections, driver
writer must create special sockets, must know about struct sk_buff
handling... Connector allows any kernelspace agents to use netlink
based networking for inter-process communication in a significantly
easier way:
int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
void cn_netlink_send(struct cn_msg *msg, u32 __groups, int gfp_mask);
struct cb_id
{
__u32 idx;
__u32 val;
};
idx and val are unique identifiers which must be registered in
connector.h for in-kernel usage. void (*callback) (void *) - is a
callback function which will be called when message with above idx.val
will be received by connector core.
Using connector completely hides low-level transport layer from it's
users.
Connector uses new netlink ability to have many groups in one socket.
[ Incorporating many cleanups and fixes by myself and
Andrew Morton -DaveM ]
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
New SBC8360 watchdog driver patch
From: Ian E. Morgan <imorgan@webcon.ca>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The device/watchdog has a fixed timeout/heartbeat.
So we don't support the WDIOC_SETTIMEOUT ioctl call
and we also may not set the WDIOF_SETTIMEOUT flag.
Cc: Andrey Panin <pazke@donpac.ru>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds driver for IBM Automatic Server Restart watchdog hardware
found in some IBM eServer xSeries machines. This driver is based on the ugly
driver provided by IBM. Driver was tested on IBM eServer 226.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
the attached patch moves the content of drivers/char/watchdog/i6300.h
into drivers/char/watchdog/i6300.c, since it is the only file using the
defines there is no real reason to have a separate header.
Also cleaned up the comments a bit and added myself to the copyright
holders.
Signed-off-by: David Hardeman <david@2gen.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
In i6300esb.c watchdog card driver were 2 bugs (misused pc_match_device and
pci_dev_put wasn't called in one error case) and one little cleanup was
done (long line was converted to a shorter one with using built-in macro).
Signed-off-by: Jiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
One pci_dev_put was misused (there was one case without putting
the device).
Changed nowayout according to other drivers.
Signed-off-by: Jiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: Naveen Gupta <ngupta@google.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch writes into bit 8 of the reload register to perform the
correct 'Reload Sequence' instead of writing into bit 4 of Watchdog for
Intel 6300ESB chipset.
Signed-off-by: Naveen Gupta <ngupta@google.com>
Signed-off-by: David Hardeman <david@2gen.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch sets the WDT_ENABLE bit of the Lock Register to enable the
watchdog and WDT_LOCK bit only if nowayout is set. The old code always
sets the WDT_LOCK bit of watchdog timer for Intel 6300ESB chipset. So, we
end up locking the watchdog instead of enabling it.
Signed-off-by: Naveen Gupta <ngupta@google.com>
Signed-off-by: David Hardeman <david@2gen.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch changes pci_find_device to pci_get_device
(encapsulated in for_each_pci_dev) in i6300esb watchdog
card with appropriate adding pci_dev_put.
Generated in 2.6.13-rc5-mm1 kernel version.
Signed-off-by: Jiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I wrote earlier to the list[1] asking for a driver for the watchdog
included in the 6300ESB chipset. I got a 2.4 driver via private email
from Ross Biro which I've changed into what I hope resembles a 2.6
driver (which was done by looking a lot at the watchdog drivers
already in the 2.6 tree).
I've attached the result, and I'm hoping to get some feedback on the
coding as a first step. I can't actually test it on the hardware
right now as I won't have physical access until April. So my own tests
have been limited to "compiles-without-warnings" and
"can-be-insmodded-in-other-machine-without-oops".
[1] http://marc.theaimsgroup.com/?l=linux-kernel&m=110711079825794&w=2
[2] http://marc.theaimsgroup.com/?l=linux-kernel&m=110711973917746&w=2
Signed-off-by: David Hardeman <david@2gen.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This ports the Sun GEM ROM mapping/enable fixes it sunhme (which used
the same PCI ROM mapping code).
Without this, I get NULL MAC addresses for all 4 ports (it's a SUN QFE).
With it, I get the correct addresses (the ones printed on the label on
the card).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This same patch was reported to fix the MAC address detection on sunhme
(next patch). Most people seem to be running this on Sparcs or PPC
machines, where we get the MAC address from their respective firmware
rather than from the (previously broken) ROM mapping routines.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is one heck of a confused driver. It uses a byte write to a dword
register to enable a ROM resource that it doesn't even seem to be using.
"Lost and wandering in the desert of confusion"
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These are small ucb1x00-ts cleanups, as suggested by Vojtech, Dmitri
and the lists.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the core device support code for the Philips UCB1200 and
UCB1300 devices. Also includes the following from Pavel:
This fixes u32 vs. pm_message_t confusion and uses cleaner
try_to_freeze() [fixing compilation as a side-effect on newer
kernels.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
set DID_NO_CONNECT for the BLKPREP_KILL case and correct a few
BLKPREP_DEFER cases that weren't checking for the need to plug the
queue.
Signed-Off-By: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The original API returned either an ERR_PTR() or a refcounted sdev.
Unfortunately, if it's successful, you need to do a scsi_device_put() on
the sdev otherwise the refcounting is wrong.
Everyone seems to expect that scsi_add_device() should be callable
without doing the ref put, so alter the API so it is (we still have
__scsi_add_device with the original behaviour).
The only actual caller that needs altering is the one in firewire ...
not because it gets this right, but because it acts on the error if one
is returned.
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clean the Kconfig+Makefile according to a sorted list
of the drivers of each architecture (and sub-architecture).
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
envctrl doesn't need unistd.h; moreover, since it declares errno static
gcc4 gets very unhappy about including unistd.h.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reference count fix merged isn't fully bug free. It doesn't leak
now, but instead it crashes due to looking at freed memory. So for now,
lets reverse the change and I'll fix it for real next week.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time to jiffies units conversion functions rather than direct HZ
division to avoid rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove S4BIOS support. It is pretty useless, and only ever worked for _me_
once. (I do not think anyone else ever tried it). It was in feature-removal
for a long time, and it should have been removed before.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Uses msleep() in place of schedule_timeout() to guarantee the task delays as
expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep() or msleep_interruptible() [as appropriate] instead of
schedule_timeout() to gurantee the task delays as expected. As a result
changed the units of the timeout variable from jiffies to msecs.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Uses msleep() instead of schedule_timeout() to guarantee
the task delays at least the desired time amount.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make code more readable with list_for_each_entry.
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I replaced the custom MIN/MAX macros with the type safe min/max macros
from linux/kernel.h.
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of the time_after() macro, defined at linux/jiffies.h, which deals with
wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the most trivial from Rusty's trivial patches:
- spelling fixes
- remove duplicate includes
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch does a full cleanup of 'NULL checks before vfree', and a partial
cleanup of calls to kfree for all of drivers/ - the kfree bit is partial in
that I only did the files that also had vfree calls in them. The patch
also gets rid of some redundant (void *) casts of pointers being passed to
[vk]free, and a some tiny whitespace corrections also crept in.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With gcc -W:
drivers/char/hpet.c:102: warning: `inline' is not at beginning of declaration
drivers/char/hpet.c:109: warning: `inline' is not at beginning of declaration
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace schedule_timeout() with msleep() to guarantee the task delays as
expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the sparse warning "implicit cast to nocast type"
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the sparse warning "implicit cast to nocast type"
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
misc_register() can fail.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pcibus_to_cpumask expands into more than just an initialiser so gcc
moans about code before variable declarations.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've noticed that the patch from Ben Dooks (commit
af4bb822bc on your git tree) is
introducing a warning. It's using 'u32 state' instead of 'pm_message_t
state'. I've attached a one liner to fix it.
Signed-Off-By: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch (as546) fixes an oops-causing failure to check the return code
from scsi_device_get. The call can return an error if the LLD is being
unloaded from memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: Smart, James <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert wbsd to use the new delay functionality in mmc_detect_change()
rather than implementing its own timer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the CM REQ handling function gets to error2, then it frees
cm_id_priv->timewait_info. But the next line goes through
ib_destroy_cm_id() -> ib_send_cm_rej() -> cm_reset_to_idle(),
which ends up calling cm_cleanup_timewait(), which dereferences the
pointer we just freed. Make sure we clear cm_id_priv->timewait_info
after freeing it, so that doesn't happen.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Changes to CM to support CM and port redirection (REJ reason 24).
Signed-off-by: John Kingman <kingman <at> storagegear.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This shouldn't be a BUG. We should cope.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If you try to assemble an array with too many missing devices, raid10 will now
reject the attempt, instead of allowing it.
Also check when hot-adding a drive and refuse the hot-add if the array is
beyond hope.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was another case where sb_size wasn't being set, so instead do the
sensible thing and set if when filling in the content of a superblock. That
ensures that whenever we write a superblock, the sb_size MUST be set.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two ways to add devices to an md/raid array.
It can have superblock written to it, and then given to the md driver,
which will read the superblock (the new way)
or
md can be told (through SET_ARRAY_INFO) the shape of the array, and
the told about individual drives, and md will create the required
superblock (the old way).
The newly introduced sb_size was only set for drives being added the
new way, not the old ways. Oops :-(
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just like failed drives have (F), so spare drives now have (S).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Leave it unchanged if the original (0.90) is used, incase it might be a
compatability problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doh. I want the physical hard-sector-size, not the current block size...
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On reflection, a better default location for hot-adding bitmaps with version-1
superblocks is immediately after the superblock. There might not be much room
there, but there is usually atleast 3k, and that is a good start.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The bitmap code used to have two daemons, so there is some 'common' start/stop
code. But now there is only one, so the common code is just noise.
This patch tidies this up somewhat.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mddev->bitmap gets clearred before the writeback daemon is stopped. So the
write_back daemon needs to be careful not to dereference the 'bitmap' if it is
NULL.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch MD to use the kthread infrastructure, to simplify the code and get rid
of tasklist_lock abuse in md_unregister_thread.
Also don't flush signals in md_thread, as the called thread will always do
that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a direct port of the raid5 patch.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most awkward part of this is delaying write requests until bitmap updates have
been flushed.
To achieve this, we have a sequence number (seq_flush) which is incremented
each time the raid5 is unplugged.
If the raid thread notices that this has changed, it flushes bitmap changes,
and assigned the value of seq_flush to seq_write.
When a write request arrives, it is given the number from seq_write, and that
write request may not complete until seq_flush is larger than the saved seq
number.
We have a new queue for storing stripes which are waiting for a bitmap flush
and an extra flag for stripes to record if the write was 'degraded' and so
should not clear the a bit in the bitmap.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
version-1 superblocks are not (normally) 4K long, and can be of variable size.
Writing the full 4K can cause corruption (but only in non-default
configurations).
With this patch the super-block-flavour can choose a size to read, and set a
size to write based on what it finds.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
read_sb_page() assumed that if sync_page_io fails, the device would be marked
faultly. However it isn't. So in the face of error, read_sb_page would loop
forever.
Redo the logic so that this cannot happen.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As this is used to flag an internal bitmap.
Also, introduce symbolic names for feature bits.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is possibly (and occasionally useful) to have a raid1 without persistent
superblocks. The code in add_new_disk for adding a device to such an array
always tries to read a superblock.
This will obviously fail.
So do the appropriate test and call md_import_device with
appropriate args.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When hot-adding a bitmap, bitmap_daemon_work could get called while the bitmap
is being created, so don't set mddev->bitmap until the bitmap is ready.
This requires freeing the bitmap inside bitmap_create if creation failed
part-way through.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'lastrun' time wasn't being initialised, so it could be half a
jiffie-cycle before it seemed to be time to do work again.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A state of 0 mean 'not quiesced'
A state of 1 means 'is quiesced'
The original code got this wrong.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
linear currently uses division by the size of the smallest componenet device
to find which device a request goes to. If that smallest device is larger
than 2 terabytes, then the division will not work on some systems.
So we introduce a pre-shift, and take care not to make the hash table too
large, much like the code in raid0.
Also get rid of conf->nr_zones, which is not needed.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a device is flagged 'WriteMostly' and the array has a bitmap, and the
bitmap superblock indicates that write_behind is allowed, then write_behind is
enabled for WriteMostly devices.
Write requests will be acknowledges as complete to the caller (via b_end_io)
when all non-WriteMostly devices have completed the write, but will not be
cleared from the bitmap until all devices complete.
This requires memory allocation to make a local copy of the data being
written. If there is insufficient memory, then we fall-back on normal write
semantics.
Signed-Off-By: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows a device in a raid1 to be marked as "write mostly". Read requests
will only be sent if there is no other option.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Both file-bitmaps and superblock bitmaps are supported.
If you add a bitmap file on the array device, you lose.
This introduces a 'default_bitmap_offset' field in mddev, as the ioctl used
for adding a superblock bitmap doesn't have room for giving an offset. Later,
this value will be setable via sysfs.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we find a 'stale' bitmap, possibly because it is new, we should just
assume every bit needs to be set, but rather base the setting of bits on the
current state of the array (degraded and recovery_cp).
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... otherwise we loose a reference and can never free the file.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix another bug in dm-raid1.c that the dirty region may stay in or be moved
to clean list and freed while in use.
It happens as follows:
CPU0 CPU1
------------------------------------------------------------------------------
rh_dec()
if (atomic_dec_and_test(pending))
<the region is still marked dirty>
rh_inc()
if the region is clean
mark the region dirty
and remove from clean list
mark the region clean
and move to clean list
atomic_inc(pending)
At this stage, the region is in clean list and will be mistakenly reclaimed
by rh_update_states() later.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md does not yet support BIO_RW_BARRIER, so be honest about it and fail
(-EOPNOTSUPP) any such requests.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
'this_sector' is a virtual (array) address while 'head_position' is a physical
(device) address, so substraction doesn't make any sense. devs[slot].addr
should be used instead of this_sector.
However, this patch doesn't make much practical different to the read
balancing due to the effects of later code.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch updates the driver for the 3ware 9000 series to do
the following:
- Correctly handle single sgl's with use_sg = 1.
This is needed with the latest scsi-block-2.6 merge otherwise the 3w-9xxx
driver will not work. I tested the patch James sent a few weeks back to fix
this, and it had a bug where the request_buffer was accessed in
twa_scsiop_execute_scsi_complete() when it was invalid. This is a corrected
variation of that patch.
Signed-off-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
completion events after destroying a CQ, QP or SRQ. We do this by
sweeping the event lists before returning from a destroy calls, and
then return the number of events already reported before the destroy
call. This allows userspace wait until it has processed all events
for an object returned from the kernel before it frees its context for
the object.
The ABI of the destroy CQ, destroy QP and destroy SRQ commands has to
change to return the event count, so bump the ABI version from 1 to 2.
The userspace libibverbs library has already been updated to handle
both the old and new ABI versions.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SA: Move SA attributes to ib_sa.h so are accessible to more than
sa_query.c. Also, remove deprecated attributes and add one missing one.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SAS transport class contains common code to deal with SAS HBAs, an
aproximated representation of SAS topologies in the driver model,
and various sysfs attributes to expose these topologies and managment
interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces
two additional intermediate objects: The SAS PHY as represented by struct
sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS
remote PHY represented by struct sas_rphy defines an "incoming" PHY on a
SAS Expander or end device. Note that this is purely a software concept, the
underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs
form a wide port based on the port_identifier attribute, which is the same
for all PHYs in a port.
This submission doesn't handle hot-plug addition or removal of SAS devices
and thus doesn't do scanning in a workqueue yet, that will be added in
phase2 after this submission. In a third phase I will add additional
managment infrastructure.
I think this submission is ready for 2.6.14, but additional comments are
of course very welcome.
I'd like to thanks James Smart a lot for his very useful input on the
design.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The soon to be released smartmontools 5.34 uses the
READ DEFECT DATA command on SCSI disks. A disk that
has defect list entries (or worse, an increasing number
of them) is at risk.
Currently the first invocation of smartctl causes this:
scsi: unknown opcode 0x37
message to appear the console and in the log.
The READ DEFECT DATA SCSI command does not change
the state of a disk. Its opcode (0x37) is valid for
SBC devices (e.g. disks) and SMC-2 devices (media
changers) where it is called INITIALIZE STATUS ELEMENT
WITH RANGE and again doesn't change the external state
of the device.
Changelog:
- mark SCSI opcode 0x37 (READ DEFECT DATA) as
safe_for_read
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Further to the problem discussed in this post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=112540053711489&w=2
It seems that the sg driver does not need to set the VM_IO flag
on pages that it memory maps to the user space since they are
not from the IO space. Ahmed Teirelbar <ahmed.teirelbar@adic.com>
wants the facility and has tested this patch as I have without
adverse effects.
The oops protection is still important. Some users really did
try and use dio transfers from the sg driver to memory mapped
IO space (on a video capture card if my memory serves) during the
lk 2.4 series. I'm not sure how successful it was but that will
now be politely refused in lk 2.6.13+ .
Changelog:
- set the page flags for sg's reserved buffer mmap-ed
to the user space to VM_RESERVED (rather than
VM_RESERVED | VM_IO )
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the reset of the chips in w83627hf optional rather than the
default. This reset has been causing trouble several times already. It
may even go completely away unless it proves to be useful to at least
one user.
Closes bug #5168:
http://bugzilla.kernel.org/show_bug.cgi?id=5168
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the head comment of the smsc47m1 driver to mention all the
supported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes to the i2c-isa design broke the force_addr parameter of
two hardware monitoring drivers as a side effect: sis5595 and via686a.
The last address test was in fact useless beforehand, and the redesign
turned it into a bug. I'm sorry about that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Actually, just one problem and one cosmetic fix:
1) We need to dequeue for the loop and kill case (it seems easiest
simply to dequeue in the scsi_kill_request() routine)
2) There's no real need to drop the queue lock. __scsi_done() is lock
agnostic, so since there's no requirement, let's just leave it in to
avoid any locking issues.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change the number of supported AoE slot addresses per AoE shelf
address to 16.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for the IBM Hard Drive Active Protection System (HDAPS), an
accelerometer found in most modern ThinkPads.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the final 20 DEFINE_SPINLOCK holdouts. (another 580 places
are already using DEFINE_SPINLOCK). Build tested on x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This set of two patches add support for the framebuffer of the Samsung S3C2410
ARM SoC. This driver was started about one year ago and is now used on iPAQ
h1930/h1940, Acer n30 and probably other s3c2410-based machines I'm not aware
of. I've also heard yesterday that it's working also on iPAQ rx3715/rx3115
(s3c2440-based machines).
Signed-Off-By: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Ben Dooks <ben@trinity.fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Quiet an incorrect warning in aty128fb and radeonfb about the PCI ROM
content. Macs work just find without that signature.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stop LCD displays from flickering during high loads.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ddc/i2c support for i810fb. This will allow the driver to get display
information, especially for monitors with fickle timings. The i2c support
depends on CONFIG_FB_I810_GTF.
Changed __init* to __devinit*
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function bit_putcs() in drivers/video/console/bitblit.c is becoming large.
Break it up into its component functions (bit_putcs_unaligned and
bit_putcs_aligned).
Incorporated fb_pad_aligned_buffer() optimization by Roman Zippel.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To solve touchscreen interference problems devices like the Sharp Zaurus
SL-C3000 need to know the length of the horitzontal sync pulses. This patch
adds a hook to pxafb so the touchscreen driver can function correctly.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The var structure in calc_mode_timings is not properly initialized (zero set)
which leads to undefined behavior when it is passed to fb_get_mode().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nvidiafb_imageblit converts the bitdata stream from big_endian to little
endian. This produces mirrored characters when machine is big_endian. Do not
endian convert on big endian machines.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If console is blanked or in KD_GRAPHICS mode, delete cursor timer. No sense
flashing the cursor when there's nothing to be seen.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make "mode_option" available when compiled as a module.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If no EDID block is probed, if the display is digital and if no mode option is
specified by the user, get the timings by CVT instead of using the global mode
database.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Coordinated Video Timings (CVT) is the latest standard approved by VESA
concerning video timings generation. It addresses the limitation of GTF which
is designed mainly for CRT displays. CRT's have a high blanking requirement
(as much as 25% of the horizontal frame length) which artificially increases
the pixelclock. Digital displays, on the other hand, needs to conserve the
pixelclock as much as possible. The GTF also does not take into account the
different aspect ratios in its calculation.
The new function added is fb_find_mode_cvt(). It is called by fb_find_mode()
if it recognizes a mode option string formatted for CVT. The format is:
<xres>x<yres>[M][R][-<bpp>][<at-sign><refresh>][i][m]
The 'M' tells the function to calculate using CVT. On it's own, it will
compute a timing for CRT displays at 60Hz. If the 'R' is specified, 'reduced
blanking' computation will be used, best for flatpanels. The 'i' and the 'm'
is for 'interlaced mode' and 'with margins' respectively.
To determine if CVT was used, check for dmesg for something like this:
CVT Mode - <pix>M<n>[-R], ie: .480M3-R (800x600 reduced blanking)
where: pix - product of xres and yres, in MB
M - is a CVT mode
n - the aspect ratio (3 - 4:3; 4 - 5:4; 9 - 16:9, 15:9; A - 16:10)
-R - reduced blanking
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes some small rearrangements of the PCI probing code in
order to make it possible for arch code to set up the PCI tree
without needing to duplicate code from the PCI layer unnecessarily.
PPC64 will use this to set up the PCI tree from the Open Firmware
device tree, which we need to do on logically-partitioned pSeries
systems.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trivial patch against 2.6.13 to unhide SMBus on Compaq Evo N620c laptop using
Intel 82855PM chipset.
Signed-off-by: Rumen Zarev <rzarev@caltech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Martin Franc reported that the pciehp driver was not enabling bus
master capability on his hot-plugged card. pciehprm_enable_card()
was updating the PCI command register only if _HPP indicated a
value for SERR or PERR that was different from the current setting.
I don't have hardware that reproduces this problem, but Martin
reports that this patch fixes the problem for him.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From rzarev@its.caltech.edu Tue Sep 6 18:29:50 2005
Date: Tue, 6 Sep 2005 13:39:32 -0700 (PDT)
From: Rumen Ivanov Zarev <rzarev@its.caltech.edu>
Message-Id: <200509062039.j86KdWMr014934@inky.its.caltech.edu>
To: gregkh@suse.de
Subject: PCI: Unhide SMBus on Compaq Evo N620c
Cc: linux-kernel@vger.kernel.org
Trivial patch against 2.6.13 to unhide SMBus on Compaq Evo N620c laptop using
Intel 82855PM chipset.
Signed-off-by: Rumen Zarev <rzarev@caltech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
drivers/pci/quirks.c | 6 ++++++
1 file changed, 6 insertions(+)
--- gregkh-2.6.orig/drivers/pci/quirks.c 2005-09-09 10:28:55.000000000 -0700
+++ gregkh-2.6/drivers/pci/quirks.c 2005-09-09 13:51:44.000000000 -0700
@@ -876,6 +876,12 @@ static void __init asus_hides_smbus_host
case 0xC00C: /* Samsung P35 notebook */
asus_hides_smbus = 1;
}
+ } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) {
+ if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
+ switch(dev->subsystem_device) {
+ case 0x0058: /* Compaq Evo N620c */
+ asus_hides_smbus = 1;
+ }
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge );
This patch changes radeon to request only resources 0 and 2 instead of all
3. This works around problems with some setups where BAR 1 (IO BAR) has
not been assigned by the firmware since it's not used on the machine and
the kernel fails to assign something to it due to the card being between a
P2P bridge that was configured without an IO range at all.
This typically fixes radeonfb on some Apple Xserve G5 machines
Signed-off-by: Daniel Burcaw <dburcaw@terrasoftsolutions.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This trivial patch gives a performance boost to the framebuffer console
Constructing the bitmaps that are given to the bitblit functions of the
framebuffer drivers is time consuming. Here we avoide a call to the slow
fb_pad_aligned_buffer(). The patch replaces that call with a simple but
much more efficient bytewise copy.
The kernel spends a significant time at this place if you use 8x* fonts.
Every pixel displayed on your screen is prepared here.
Some benchmark results:
Displaying a file of 2000 lines with 160 characters each takes 889 ms
system time using cyblafb on my system (Im using a 1280x1024 video mode,
resulting in a 160x64 character console)
Displaying the same file with the enclosed patch applied to 2.6.13 only
takes 760 ms system time, saving 129 ms or 14.5%.
Font widths other than 8 are not affected.
The advantage and correctness of this patch should be obvious.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a framebuffer driver for the Cyberblade/i1 graphics core.
Currently tridenfb claims to support the cyberblade/i1 graphics core. This
is of very limited truth. Even vesafb is faster and provides more working
modes and a much better quality of the video signal. There is a great
number of bugs in tridentfb ... but most often it is impossible to decide
if these bugs are real bugs or if fixing them for the cyberblade/i1 core
would break support for one of the other supported chips.
Tridentfb seems to be unmaintained,and documentation for most of the
supported chips is not available. So "fixing" cyberblade/i1 support inside
of tridentfb was not an option, it would have caused numerous
if(CYBERBLADEi1) else ... cases and would have rendered the code to be
almost unmaintainable.
A first version of this driver was published on 2005-07-31. A fix for a
bug reported by Jochen Hein was integrated as well as some changes
requested by Antonino A. Daplas.
A message has been added to tridentfb to inform current users of tridentfb
to switch to cyblafb if the cyberblade/i1 graphics core is detected.
This patch is one logical change, but because of the included documentation
it is bigger than 70kb. Therefore it is not sent to lkml and
linux-fbdev-devel,
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
err remains uninitialized of pci_request_regions fails.
Found by Thorsten Kukuk, I added a few more checks.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This lifts sisfb from version 1.7.17 to version 1.8.9. Changes include:
- Added support for XGI V3XT, V5, V8, Z7 chipsets, including POSTing of
all of these chipsets.
- Added support for latest SiS chipsets (761).
- Added support for SiS76x memory "hybrid" mode.
- Added support for new LCD resolutions (eg 1280x854, 856x480).
- Fixed support for 320x240 STN panels (for embedded devices).
- Fixed many HDTV modes (525p, 750p, 1080i).
- Fixed PCI config register reading/writing to use proper kernel
functions for this purpose.
- Fixed PCI ROM handling to use the kernel's proper functions.
- Removed lots of "typedef"s.
- Removed lots of code which was for X.org/XFree86 only.
- Fixed coding style in many places.
- Removed lots of 2.4 cruft.
- Reduced stack size by unifying two previously separate structs into
one.
- Added new hooks for memory allocation (for DRM). Now the driver can
truly handle multiple cards, including memory management.
- Fixed numerous minor bugs.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the matroxfb code so that it can find the PInS data embedded
in the BIOS on PowerPC cards. The process for finding the data is
different on OpenFirmware cards than on x86 cards, and the code for doing
so was missing.
After patching, building, installing, and booting a kernel, you should grep
for "PInS" in /var/log/messages. You should see two messages in the log:
PInS data found at offset XXXXX
PInS memtype = X
On the GXT135p card I get "31168" and "5". The first value is irrelevant,
but it's presence lets me know that the PInS data was actually found. On a
GXT130p, the second value should be 3. Since I don't have access to that
hardware, if someone can verify that, I will submit a follow-on patch that
rips out all the memtype parameter stuff.
Signed-off-by: Ian Romanick <idr@us.ibm.com>
Signed-off-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The link for ATI's product page in drivers/video/Kconfig for FB_RADEON is
broken. Replace with a product comparison page.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, atyfb has code that sets the hsync and vsync polarity based on the
current video mode, without letting the user override the settings.
Remove this particular code. The sync polarities are set by the PROM, the
user or by the videomode.
Signed-off-by: Alexander Kern <alex.kern@gmx.de>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On a vc resize, the contents of the old screen buffer are transferred to the
new screenbuffer. If the new screenbuffer is smaller than the old one, only
the contents from the bottom are copied to new. If the contents of the old
buffer are located at the top, then the contents will not be copied to the new
buffer resulting in a blank screen.
This bug will happen only if the vc in question is not in the foreground.
Doing an fbset -a or con2fbmap will trigger this bug.
To fix this problem, base the start of the copy from the location of the
current cursor. If the cursor is near the top of the buffer, copy the
contents at the top, and if the cursor is near the bottom of the buffer, then
copy the contents at the bottom. In the unlikely case where the new row size
is greater than 2x smaller than the old one, and the cursor is in the middle,
copy 1/2 screenful from the top and bottom of the cursor position.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, the default linux 16-colors are converted to 4-colors by simply
dividing the values by 4. However, this is not necessarily correct since the
first 4 colors are converted to black, rendering them invisible.
So, for black, no conversion; for light colors, convert to gray, for normal
text color, no conversion, and for bright colors, convert to intense white.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, fbcon assumes that the visual FB_VISUAL_MONO* is always 1 bit.
According to Geert, there are old hardware where it's possible to have
monochrome at 8-bit, but has only 2 colors, black - 0x00 and white - 0xff.
Fix color handlers (fb_get_color_depth, and get_color) for this special case.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If nvidiafb fails to probe the EDID block, get the EDID from the BIOS.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fallback to firmware EDID if chipset has no DDC/I2C support or if I2C
probing failed
- Add fb_blank hook
- Fix savagefb_suspend/resume to enable driver to successfully suspend and
resume from S3, memory or disk
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For the i386, code is already present in video.S that gets the EDID from the
video BIOS. Make this visible so drivers can also use this data as fallback
when i2c does not work.
To ensure that the EDID block is returned for the primary graphics adapter
only, by check if the IORESOURCE_ROM_SHADOW flag is set.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Geode framebuffer driver updates:
- Local mode list (taken from modedb.c) containing only relevant modes.
This also makes the driver work as a module.
- Make it a PCI driver (from James Simmons <jsimmons@infradead.org>).
- A few other minor cosmetic bits and pieces.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes drivers that have hardware cursors from calling the
software cursor code. Also if the driver sets a no hardware cursor flag
then the driver reports a error it someone attempts to use the cursor.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add rudimentary support by manipulating the VGA registers. However, not
all vesa modes are VGA compatible, so VGA compatiblity is checked first.
Only 2 levels are supported, powerup and powerdown.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add capability to fbdev to listen to the FB_ACTIVATE_ALL flag. If set, it
notifies fbcon that all consoles must be set to the current var.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the use of RCU in files structure, the look-up of files using fds can now
be lock-free. The lookup is protected by rcu_read_lock()/rcu_read_unlock().
This patch changes the readers to use lock-free lookup.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Ravikiran Thirumalai <kiran_th@gmail.com>
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order for the RCU to work, the file table array, sets and their sizes must
be updated atomically. Instead of ensuring this through too many memory
barriers, we put the arrays and their sizes in a separate structure. This
patch takes the first step of putting the file table elements in a separate
structure fdtable that is embedded withing files_struct. It also changes all
the users to refer to the file table using files_fdtable() macro. Subsequent
applciation of RCU becomes easier after this.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Include saa6588 compiler option and files.
- Fix comment on tuner.h
- linux/utsname.h replaced by linux/version.h to compile on vanilla 2.6.13
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Makes the input event device created by the V4L drivers for the
infrared remote matchable by udev rules.
Signed-off-by: Rudo Thomas <rudo@matfyz.cz>
Signed-off-by: Michael Fair <michael@daclubhouse.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- print warning if pal= or secam= argument is unrecognized
Signed-off-by: Philip Rowlands <phr@doc.ic.ac.uk>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- correct the amux for composite and s-video inputs on the Sabrent SBT-TVFM
card.
Signed-off-by: Michael Rodriquez-Torrent <mike@themikecam.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
