With CONFIG_SHIRQ_DEBUG=y we call a newly installed interrupt handler
in request_threaded_irq().
The original implementation (commit a304e1b8) called the handler
_BEFORE_ it was installed, but that caused problems with handlers
calling disable_irq_nosync(). See commit 377bf1e4.
It's braindead in the first place to call disable_irq_nosync in shared
handlers, but ....
Moving this call after we installed the handler looks innocent, but it
is very subtle broken on SMP.
Interrupt handlers rely on the fact, that the irq core prevents
reentrancy.
Now this debug call violates that promise because we run the handler
w/o the IRQ_INPROGRESS protection - which we cannot apply here because
that would result in a possibly forever masked interrupt line.
A concurrent real hardware interrupt on a different CPU results in
handler reentrancy and can lead to complete wreckage, which was
unfortunately observed in reality and took a fricking long time to
debug.
Leave the code here for now. We want this debug feature, but that's
not easy to fix. We really should get rid of those
disable_irq_nosync() abusers and remove that function completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: stable@kernel.org # .28 -> .37
Lars-Peter Clausen pointed out:
I stumbled upon this while looking through the existing archs using
SPARSE_IRQ. Even with SPARSE_IRQ the NR_IRQS is still the upper
limit for the number of IRQs.
Both PXA and MMP set NR_IRQS to IRQ_BOARD_START, with
IRQ_BOARD_START being the number of IRQs used by the core.
In various machine files the nr_irqs field of the ARM machine
defintion struct is then set to "IRQ_BOARD_START + NR_BOARD_IRQS".
As a result "nr_irqs" will greater then NR_IRQS which then again
causes the "allocated_irqs" bitmap in the core irq code to be
accessed beyond its size overwriting unrelated data.
The core code really misses a sanity check there.
This went unnoticed so far as by chance the compiler/linker places
data behind that bitmap which gets initialized later on those affected
platforms.
So the obvious fix would be to add a sanity check in early_irq_init()
and break all affected platforms. Though that check wants to be
backported to stable as well, which will require to fix all known
problematic platforms and probably some more yet not known ones as
well. Lots of churn.
A way simpler solution is to allocate a slightly larger bitmap and
avoid the whole churn w/o breaking anything. Add a few warnings when
an arch returns utter crap.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org # .37
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reason: irq/for-mips is provided for mips to make core independent
progress. Merge it into irq/core to avoid conflicts
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_chips that supply .irq_bus_lock/.irq_bus_sync_unlock functions,
expect that the other chip methods will be called inside of calls to
the pair. If this expectation is not met, things tend to not work.
Make setup_irq() call chip_bus_lock()/chip_bus_sync_unlock() too.
For the vast majority of irq_chips, this will be a NOP as most don't
have these bus lock functions.
[ tglx: No we don't want to call that in __setup_irq(). Way too many
error exit pathes. ]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
LKML-Reference: <1297296265-18680-1-git-send-email-ddaney@caviumnetworks.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
CONFIG_KSTAT_IRQS_ONDEMAND does not exist. It's not worth to implement
it. Use sparse irqs if you care about memory consumption of the
interrupt layer.
Found by undertaker: http://vamos.informatik.uni-erlangen.de/trac/undertaker
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq/for-xen contains new functionality to avoid Xen private irq
hackery. That branch has a single irq commit and is pulled by Xen to
base their new features on.
Merge it into irq/core as other patches modify the same code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xen needs to reenable interrupts which are marked IRQF_NO_SUSPEND in the
resume path. Add a flag to force the reenabling in the resume code.
Tested-and-acked-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
move_native_irq() masks and unmasks the interrupt line
unconditionally, but the interrupt line might be masked due to a
threaded oneshot handler in progress. Unmasking the line in that case
can lead to interrupt storms. Observed on PREEMPT_RT.
Originally-from: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
The new code of commit cd7eab44e(genirq: Add IRQ affinity notifiers)
references irq_desc.affinity which fails to compile with
CONFIG_GENERIC_HARDIRQS_NO_DEPRECATED=y.
Use irq_desc.irq_data.affinity instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ben Hutchings <bhutchings@solarflare.com>
When initiating I/O on a multiqueue and multi-IRQ device, we may want
to select a queue for which the response will be handled on the same
or a nearby CPU. This requires a reverse-map of IRQ affinity. Add a
notification mechanism to support this.
This is based closely on work by Thomas Gleixner <tglx@linutronix.de>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: linux-net-drivers@solarflare.com
Cc: Tom Herbert <therbert@google.com>
Cc: David Miller <davem@davemloft.net>
LKML-Reference: <1295470904.11126.84.camel@bwh-desktop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All architectures are finally converted. Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Use modern per_cpu API to increment {soft|hard}irq counters, and use
per_cpu allocation for (struct irq_desc)->kstats_irq instead of an array.
This gives better SMP/NUMA locality and saves few instructions per irq.
With small nr_cpuids values (8 for example), kstats_irq was a small array
(less than L1_CACHE_BYTES), potentially source of false sharing.
In the !CONFIG_SPARSE_IRQ case, remove the huge, NUMA/cache unfriendly
kstat_irqs_all[NR_IRQS][NR_CPUS] array.
Note: we still populate kstats_irq for all possible irqs in
early_irq_init(). We probably could use on-demand allocations. (Code
included in alloc_descs()). Problem is not all IRQS are used with a prior
alloc_descs() call.
kstat_irqs_this_cpu() is not used anymore, remove it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function-scope statics are discouraged because they are
easily overlooked and can cause subtle bugs/races due to
their global (non-SMP safe) nature.
Linus noticed that we did this for sched_param - at minimum
make the const.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: Message-ID: <AANLkTinotRxScOHEb0HgFgSpGPkq_6jKTv5CfvnQM=ee@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since commit a1afb637(switch /proc/irq/*/spurious to seq_file) all
/proc/irq/XX/spurious files show the information of irq 0.
Current irq_spurious_proc_open() passes on NULL as the 3rd argument,
which is used as an IRQ number in irq_spurious_proc_show(), to the
single_open(). Because of this, all the /proc/irq/XX/spurious file
shows IRQ 0 information regardless of the IRQ number.
To fix the problem, irq_spurious_proc_open() must pass on the
appropreate data (IRQ number) to single_open().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Yong Zhang <yong.zhang0@gmail.com>
LKML-Reference: <4CF4B778.90604@jp.fujitsu.com>
Cc: stable@kernel.org [2.6.33+]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix up irq_node() for irq_data changes.
genirq: Add single IRQ reservation helper
genirq: Warn if enable_irq is called before irq is set up
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
semaphore: Remove mutex emulation
staging: Final semaphore cleanup
jbd2: Convert jbd2_slab_create_sem to mutex
hpfs: Convert sbi->hpfs_creation_de to mutex
Fix up trivial change/delete conflicts with deleted 'dream' drivers
(drivers/staging/dream/camera/{mt9d112.c,mt9p012_fox.c,mt9t013.c,s5k3e2fx.c})
In /proc/stat, the number of per-IRQ event is shown by making a sum each
irq's events on all cpus. But we can make use of kstat_irqs().
kstat_irqs() do the same calculation, If !CONFIG_GENERIC_HARDIRQ,
it's not a big cost. (Both of the number of cpus and irqs are small.)
If a system is very big and CONFIG_GENERIC_HARDIRQ, it does
for_each_irq()
for_each_cpu()
- look up a radix tree
- read desc->irq_stat[cpu]
This seems not efficient. This patch adds kstat_irqs() for
CONFIG_GENRIC_HARDIRQ and change the calculation as
for_each_irq()
look up radix tree
for_each_cpu()
- read desc->irq_stat[cpu]
This reduces cost.
A test on (4096cpusp, 256 nodes, 4592 irqs) host (by Jack Steiner)
%time cat /proc/stat > /dev/null
Before Patch: 2.459 sec
After Patch : .561 sec
[akpm@linux-foundation.org: unexport kstat_irqs, coding-style tweaks]
[akpm@linux-foundation.org: fix unused variable 'per_irq_sum']
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Jack Steiner <steiner@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton pointed out almost all sched_setscheduler() callers are
using fixed parameters and can be converted to static. It reduces runtime
memory use a little.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: James Morris <jmorris@namei.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The recent changes in the genirq core unearthed a bug in arch/um which
called enable_irq() before the interrupt was set up.
Warn and return instead of crashing the machine with a NULL pointer
dereference.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Weinberger <richard@nod.at>
This option can be set to verify the full conversion to the new chip
functions. Fix the fallout of the patch rework, so the core code
compiles and works with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The allocator functions are now called outside of preempt disabled
regions. Switch to GFP_KERNEL.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The move_irq_desc() function was only used due to the problem that the
allocator did not free the old descriptors. So the descriptors had to
be moved in create_irq_nr(). That's history.
The code would have never been able to move active interrupt
descriptors on affinity settings. That can be done in a completely
different way w/o all this horror.
Remove all of it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Use the cleanup functions of the dynamic allocator. No need to have
separate implementations.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
This function should have not been there in the first place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
sparse irq sets up NR_IRQS_LEGACY irq descriptors and archs then go
ahead and allocate more.
Use the unused return value of arch_probe_nr_irqs() to let the
architecture return the number of early allocations. Fix up all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Make irq_to_desc_alloc_node() a wrapper around the new allocator.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Mark a range of interrupts as allocated. In the SPARSE_IRQ=n case we
need this to update the bitmap for the legacy irqs so the enumerator
via irq_get_next_irq() works.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
/proc/irq never removes any entries, but when irq descriptors can be
freed for real this is necessary. Otherwise we'd reference a freed
descriptor in /proc/irq/N
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The current sparse_irq allocator has several short comings due to
failures in the design or the lack of it:
- Requires iteration over the number of active irqs to find a free slot
(Some architectures have grown their own workarounds for this)
- Removal of entries is not possible
- Racy between create_irq_nr and destroy_irq (plugged by horrible
callbacks)
- Migration of active irq descriptors is not possible
- No bulk allocation of irq ranges
- Sprinkeled irq_desc references all over the place outside of kernel/irq/
(The previous chip functions series is addressing this issue)
Implement a sane allocator which fixes the above short comings (though
migration of active descriptors needs a full tree wide cleanup of the
direct and mostly unlocked access to irq_desc).
The new allocator still uses a radix_tree, but uses a bitmap for
keeping track of allocated irq numbers. That allows:
- Fast lookup of a free slot
- Allows the removal of descriptors
- Prevents the create/destroy race
- Bulk allocation of consecutive irq ranges
- Basic design is ready for migration of life descriptors after
further cleanups
The bitmap is also used in the SPARSE_IRQ=n case for lookup and
raceless (de)allocation of irq numbers. So it removes the requirement
for looping through the descriptor array to find slots.
Right now it uses sparse_irq_lock to protect the bitmap and the radix
tree, but after cleaning up all users we should be able convert that
to a mutex and to switch the radix_tree and decriptor allocations to
GFP_KERNEL.
[ Folded in a bugfix from Yinghai Lu ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Arch code sets it's own irq_desc.status flags right after boot and for
dynamically allocated interrupts. That might involve iterating over a
huge array.
Allow ARCH_IRQ_INIT_FLAGS to set separate flags aside of IRQ_DISABLED
which is the default.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The statistics accessor is only used by proc/stats and
show_interrupts(). Both are compiled in.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
early_init_irq_lock_class() is called way before anything touches the
irq descriptors. In case of SPARSE_IRQ=y this is a NOP operation
because the radix tree is empty at this point. For the SPARSE_IRQ=n
case it's sufficient to set the lock class in early_init_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
kernel/irq/handle.c has become a dumpground for random code in random
order. Split out the irq descriptor management and the dummy irq_chip
implementation into separate files. Cleanup the include maze while at
it.
No code change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Get the data structure from the core and provide inline wrappers to
access the irq_data members.
Provide accessor inlines for irq_data as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Provide a irq_desc.status modifier function to cleanup the direct
access to irq_desc in arch and driver code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
This option covers now the old chip functions and the irq_desc data
fields which are moving to struct irq_data. More stuff will follow.
Pretty handy for testing a conversion, whether something broke or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function retrigger() until the migration is complete
and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121843.025801092@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function set_wake() until the migration is complete
and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.927527393@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function set_type() until the migration is complete
and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.832261548@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function set_affinity() until the migration is
complete and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.732894108@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function startup() until the migration is complete and
the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.635152961@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip functions disable() and shutdown() until the
migration is complete and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.532070631@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function enable() until the migration is complete and
the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.437159182@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function eoi() until the migration is complete and
the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.339657617@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function mask_ack() until the migration is complete
and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.240806983@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function ack() until the migration is complete and
the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.142624725@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function unmask() until the migration is complete
and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121842.043608928@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip function mask() until the migration is complete and
the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121841.940355859@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Wrap the old chip functions for bus_lock/bus_sync_unlock until the
migration is complete and the old chip functions are removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121841.842536121@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The compat functions go away when the core code is converted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Convert all references in the core code to orq, chip, handler_data,
chip_data, msi_desc, affinity to irq_data.*
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Low level chip functions need access to irq_desc->handler_data,
irq_desc->chip_data and irq_desc->msi_desc. We hand down the irq
number to the low level functions, so they need to lookup irq_desc.
With sparse irq this means a radix tree lookup.
We could hand down irq_desc itself, but low level chip functions have
no need to fiddle with it directly and we want to restrict access to
irq_desc further.
Preparatory patch for new chip functions.
Note, that the ugly anon union/struct is there to avoid a full tree
wide clean up for now. This is not going to last 3 years like __do_IRQ()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121841.645542300@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The generic irq Kconfig options are copied around all archs. Provide a
generic Kconfig file which can be included.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121843.217333624@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
3 years transition phase is enough. Cleanup the last users and remove
the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Leo Chen <leochen@broadcom.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
A small number of users of IRQF_TIMER are using it for the implied no
suspend behaviour on interrupts which are not timer interrupts.
Therefore add a new IRQF_NO_SUSPEND flag, rename IRQF_TIMER to
__IRQF_TIMER and redefine IRQF_TIMER in terms of these new flags.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: xen-devel@lists.xensource.com
Cc: linux-input@vger.kernel.org
Cc: linuxppc-dev@ozlabs.org
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1280398595-29708-1-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The set_type() function can change the chip implementation when the
trigger mode changes. That might result in using an non-initialized
irq chip when called from __setup_irq() or when called via
set_irq_type() on an already enabled irq.
The set_irq_type() function should not be called on an enabled irq,
but because we forgot to put a check into it, we have a bunch of users
which grew the habit of doing that and it never blew up as the
function is serialized via desc->lock against all users of desc->chip
and they never hit the non-initialized irq chip issue.
The easy fix for the __setup_irq() issue would be to move the
irq_chip_set_defaults(desc->chip) call after the trigger setting to
make sure that a chip change is covered.
But as we have already users, which do the type setting after
request_irq(), the safe fix for now is to call irq_chip_set_defaults()
from __irq_set_trigger() when desc->set_type() changed the irq chip.
It needs a deeper analysis whether we should refuse to change the chip
on an already enabled irq, but that'd be a large scale change to fix
all the existing users. So that's neither stable nor 2.6.35 material.
Reported-by: Esben Haabendal <eha@doredevelopment.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@ozlabs.org>
Cc: stable@kernel.org
When an interrupt is disabled and torn down, the CPU mask returned
through affinity_hint right now is all CPUs. Also, for drivers that
don't provide an affinity_hint mask, this can be misleading. There
should be no hint at all, meaning an empty CPU mask.
[ tglx: use zalloc_cpumask_var instead of clearing it under the lock ]
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: davem@davemloft.net
Cc: arjan@linux.jf.intel.com
Cc: bhutchings@solarflare.com
LKML-Reference: <20100505205638.5426.87189.stgit@ppwaskie-hc2.jf.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a cpumask affinity hint to the irq_desc structure,
along with a registration function and a read-only proc entry for each
interrupt.
This affinity_hint handle for each interrupt can be used by underlying
drivers that need a better mechanism to control interrupt affinity.
The underlying driver can register a cpumask for the interrupt, which
will allow the driver to provide the CPU mask for the interrupt to
anything that requests it. The intent is to extend the userspace
daemon, irqbalance, to help hint to it a preferred CPU mask to balance
the interrupt into.
[ tglx: Fixed compile warnings, added WARN_ON, made SMP only ]
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: davem@davemloft.net
Cc: arjan@linux.jf.intel.com
Cc: bhutchings@solarflare.com
LKML-Reference: <20100430214445.3992.41647.stgit@ppwaskie-hc2.jf.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove all code which is related to IRQF_DISABLED from the core kernel
code. IRQF_DISABLED still exists as a flag, but becomes a NOOP and
will be removed after a grace period. That way we can easily revert to
the previous behaviour by just restoring the core code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@osdl.org>
LKML-Reference: <20100326000405.991244690@linutronix.de>
Running interrupt handlers with interrupts enabled can cause stack
overflows. That has been observed with multiqueue NICs delivering all
their interrupts to a single core. We might band aid that somehow by
checking the interrupt stacks, but the real safe fix is to run the irq
handlers with interrupts disabled.
Drivers for whacky hardware still can reenable them in the handler
itself, if the need arises. (They do already due to lockdep)
The risk of doing this is rather low:
- lockdep already enforces this
- CONFIG_NOHZ has shaken out the drivers which relied on jiffies updates
- time keeping is not longer sensitive to the timer interrupt being delayed
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@osdl.org>
LKML-Reference: <20100326000405.758579387@linutronix.de>
Now that we enjoy threaded interrupts, we're starting to see irq_chip
implementations (wm831x, pca953x) that make use of threaded interrupts
for the controller, and nested interrupts for the client interrupt. It
all works very well, with one drawback:
Drivers requesting an IRQ must now know whether the handler will
run in a thread context or not, and call request_threaded_irq() or
request_irq() accordingly.
The problem is that the requesting driver sometimes doesn't know
about the nature of the interrupt, specially when the interrupt
controller is a discrete chip (typically a GPIO expander connected
over I2C) that can be connected to a wide variety of otherwise perfectly
supported hardware.
This patch introduces the request_any_context_irq() function that mostly
mimics the usual request_irq(), except that it checks whether the irq
level is configured as nested or not, and calls the right backend.
On success, it also returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED.
[ tglx: Made return value an enum, simplified code and made the export
of request_any_context_irq GPL ]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: <joachim.eastwood@jotron.com>
LKML-Reference: <927ea285bd0c68934ddae1a47e44a9ba@localhost>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Force MSI irq handlers to run with interrupts disabled
Network folks reported that directing all MSI-X vectors of their multi
queue NICs to a single core can cause interrupt stack overflows when
enough interrupts fire at the same time.
This is caused by the fact that we run interrupt handlers by default
with interrupts enabled unless the driver reuqests the interrupt with
the IRQF_DISABLED set. The NIC handlers do not set this flag, so
simultaneous interrupts can nest unlimited and cause the stack
overflow.
The only safe counter measure is to run the interrupt handlers with
interrupts disabled. We can't switch to this mode in general right
now, but it is safe to do so for MSI interrupts.
Force IRQF_DISABLED for MSI interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Linus Torvalds <torvalds@osdl.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: stable@kernel.org
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Move two IRQ functions from .init.text to .text
genirq: Protect access to irq_desc->action in can_request_irq()
genirq: Prevent oneshot irq thread race
Both functions should not be marked as __init, since they be called
from modules after the init section is freed.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Kosina <jkosina@suse.cz>
LKML-Reference: <1269431961-5731-1-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
can_request_irq() accesses and dereferences irq_desc->action w/o
holding irq_desc->lock. So action can be freed on another CPU before
it's dereferenced. Unlikely, but ...
Protect it with desc->lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Expose irq_desc->node as /proc/irq/*/node.
This file provides device hardware locality information for apps
desiring to include hardware locality in irq mapping decisions.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Lars-Peter pointed out that the oneshot threaded interrupt handler
code has the following race:
CPU0 CPU1
hande_level_irq(irq X)
mask_ack_irq(irq X)
handle_IRQ_event(irq X)
wake_up(thread_handler)
thread handler(irq X) runs
finalize_oneshot(irq X)
does not unmask due to
!(desc->status & IRQ_MASKED)
return from irq
does not unmask due to
(desc->status & IRQ_ONESHOT)
This leaves the interrupt line masked forever.
The reason for this is the inconsistent handling of the IRQ_MASKED
flag. Instead of setting it in the mask function the oneshot support
sets the flag after waking up the irq thread.
The solution for this is to set/clear the IRQ_MASKED status whenever
we mask/unmask an interrupt line. That's the easy part, but that
cleanup opens another race:
CPU0 CPU1
hande_level_irq(irq)
mask_ack_irq(irq)
handle_IRQ_event(irq)
wake_up(thread_handler)
thread handler(irq) runs
finalize_oneshot_irq(irq)
unmask(irq)
irq triggers again
handle_level_irq(irq)
mask_ack_irq(irq)
return from irq due to IRQ_INPROGRESS
return from irq
does not unmask due to
(desc->status & IRQ_ONESHOT)
This requires that we synchronize finalize_oneshot_irq() with the
primary handler. If IRQ_INPROGESS is set we wait until the primary
handler on the other CPU has returned before unmasking the interrupt
line again.
We probably have never seen that problem because it does not happen on
UP and on SMP the irqbalancer protects us by pinning the primary
handler and the thread to the same CPU.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Use radix_tree irq_desc_tree instead of irq_desc_ptrs.
-v2: according to Eric and cyrill to use radix_tree_lookup_slot and
radix_tree_replace_slot
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-32-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add replace_irq_desc() instead of poking at the array directly.
-v2: remove unneeded boundary check in replace_irq_desc
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-31-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
mem_init is moved early already.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-29-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Keep chip_data in create_irq_nr and destroy_irq.
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
destroy_irq()
dynamic_irq_cleanup() which sets desc->chip_data = NULL
...race window...
desc->chip_data = cfg;
Remove the save and restore code for cfg in create_irq_nr() and
destroy_irq() and take the desc->lock when checking the irq_cfg.
Reported-and-analyzed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Brandon Phililps <bphilips@suse.de>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ntp: Provide compability defines (You say MOD_NANO, I say ADJ_NANO)
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: do not execute DEBUG_SHIRQ when irq setup failed
single_open data argument must be PDE(inode)->data instead of NULL
otherwise seq_file->private is always NULL and we always read the
spurious data of irq 0.
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ tglx: compacted it a bit ]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
LKML-Reference: <20090828181743.GA14050@x200.localdomain>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If a parent directory (ie /proc/irq/<irq>) could not be created
we should not attempt to create subdirectories. Otherwise it
would lead that "smp_affinity" and "spurious" entries are may be
registered under /proc root instead of a proper place.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20091026202811.GD5321@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit 74296a8ed added this function for debug purposes, but it was
never used for anything. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix docbook comments to match the actual function names
(set_irq_msi, handle_percpu_irq).
Signed-off-by: Liuwenyi <qingshenlwy@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'irq-threaded-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Do not mask oneshot edge type interrupts
genirq: Support nested threaded irq handling
genirq: Add buslock support
genirq: Add oneshot support
when there is no ram on node 0.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <4A95C32D.5040605@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Masking oneshot edge type interrupts is wrong as we might lose an
interrupt which is issued when the threaded handler is handling the
device. We can keep the irq unmasked safely as with edge type
interrupts there is no danger of interrupt floods. If the threaded
handler has not yet finished then IRQTF_RUNTHREAD is set which will
keep the handler thread active.
Debugged and verified in preempt-rt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The wake_up_process() of the new irq thread in __setup_irq() is too
early as the irqaction is not yet fully initialized especially
action->irq is not yet set. The interrupt thread might dereference the
wrong irq descriptor.
Move the wakeup after the action is installed and action->irq has been
set.
Reported-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Interrupt chips which are behind a slow bus (i2c, spi ...) and
demultiplex other interrupt sources need to run their interrupt
handler in a thread.
The demultiplexed interrupt handlers need to run in thread context as
well and need to finish before the demux handler thread can reenable
the interrupt line. So the easiest way is to run the sub device
handlers in the context of the demultiplexing handler thread.
To avoid that a separate thread is created for the subdevices the
function set_nested_irq_thread() is provided which sets the
IRQ_NESTED_THREAD flag in the interrupt descriptor.
A driver which calls request_threaded_irq() must not be aware of the
fact that the threaded handler is called in the context of the
demultiplexing handler thread. The setup code checks the
IRQ_NESTED_THREAD flag which was set from the irq chip setup code and
does not setup a separate thread for the interrupt. The primary
function which is provided by the device driver is replaced by an
internal dummy function which warns when it is called.
For the demultiplexing handler a helper function handle_nested_irq()
is provided which calls the demux interrupt thread function in the
context of the caller and does the proper interrupt accounting and
takes the interrupt disabled status of the demultiplexed subdevice
into account.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The
bus access needs to sleep and therefor cannot be called in atomic
contexts.
Some of the generic interrupt management functions like disable_irq(),
enable_irq() ... call interrupt chip functions with the irq_desc->lock
held and interrupts disabled. This does not work for such devices.
Provide a separate synchronization mechanism for such interrupt
chips. The irq_chip structure is extended by two optional functions
(bus_lock and bus_sync_and_unlock).
The idea is to serialize the bus access for those operations in the
core code so that drivers which are behind that bus operated interrupt
controller do not have to worry about it and just can use the normal
interfaces. To achieve this we add two function pointers to the
irq_chip: bus_lock and bus_sync_unlock.
bus_lock() is called to serialize access to the interrupt controller
bus.
Now the core code can issue chip->mask/unmask ... commands without
changing the fast path code at all. The chip implementation merily
stores that information in a chip private data structure and
returns. No bus interaction as these functions are called from atomic
context.
After that bus_sync_unlock() is called outside the atomic context. Now
the chip implementation issues the bus commands, waits for completion
and unlocks the interrupt controller bus.
The irq_chip implementation as pseudo code:
struct irq_chip_data {
struct mutex mutex;
unsigned int irq_offset;
unsigned long mask;
unsigned long mask_status;
}
static void bus_lock(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
mutex_lock(&data->mutex);
}
static void mask(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
irq -= data->irq_offset;
data->mask |= (1 << irq);
}
static void unmask(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
irq -= data->irq_offset;
data->mask &= ~(1 << irq);
}
static void bus_sync_unlock(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
if (data->mask != data->mask_status) {
do_bus_magic_to_set_mask(data->mask);
data->mask_status = data->mask;
}
mutex_unlock(&data->mutex);
}
The device drivers can use request_threaded_irq, free_irq, disable_irq
and enable_irq as usual with the only restriction that the calls need
to come from non atomic context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
For threaded interrupt handlers we expect the hard interrupt handler
part to mask the interrupt on the originating device. The interrupt
line itself is reenabled after the hard interrupt handler has
executed.
This requires access to the originating device from hard interrupt
context which is not always possible. There are devices which can only
be accessed via a bus (i2c, spi, ...). The bus access requires thread
context. For such devices we need to keep the interrupt line masked
until the threaded handler has executed.
Add a new flag IRQF_ONESHOT which allows drivers to request that the
interrupt is not unmasked after the hard interrupt context handler has
been executed and the thread has been woken. The interrupt line is
unmasked after the thread handler function has been executed.
Note that for now IRQF_ONESHOT cannot be used with IRQF_SHARED to
avoid complex accounting mechanisms.
For oneshot interrupts the primary handler simply returns
IRQ_WAKE_THREAD and does nothing else. A generic implementation
irq_default_primary_handler() is provided to avoid useless copies all
over the place. It is automatically installed when
request_threaded_irq() is called with handler=NULL and
thread_fn!=NULL.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
free_irq() can remove an irqaction while the corresponding interrupt
is in progress, but free_irq() sets action->thread to NULL
unconditionally, which might lead to a NULL pointer dereference in
handle_IRQ_event() when the hard interrupt context tries to wake up
the handler thread.
Prevent this by moving the thread stop after synchronize_irq(). No
need to set action->thread to NULL either as action is going to be
freed anyway.
This fixes a boot crash reported against preempt-rt which uses the
mainline irq threads code to implement full irq threading.
[ tglx: removed local irqthread variable ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This takes care of the following entry from Dan's list:
kernel/irq/resend.c +73 check_irq_resend(17) warning: variable derefenced before check 'desc->chip'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Julia Lawall <julia@diku.dk>
LKML-Reference: <200908062146.03638.bzolnier@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't move it if target node is -1.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4A785B5D.4070702@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since genirq: Delegate irq affinity setting to the irq thread
(591d2fb02e) compilation with
CONFIG_SMP=n fails with following error:
/usr/src/linux-2.6/kernel/irq/manage.c:
In function 'irq_thread_check_affinity':
/usr/src/linux-2.6/kernel/irq/manage.c:475:
error: 'struct irq_desc' has no member named 'affinity'
make[4]: *** [kernel/irq/manage.o] Error 1
That commit adds a new function irq_thread_check_affinity() which
uses struct irq_desc.affinity which is only available for CONFIG_SMP=y.
Move that function under #ifdef CONFIG_SMP.
[ tglx@brownpaperbag: compile and boot tested on UP and SMP ]
Signed-off-by: Bruno Premont <bonbons@linux-vserver.org>
LKML-Reference: <20090722222232.2eb3e1c4@neptune.home>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_set_thread_affinity() calls set_cpus_allowed_ptr() which might
sleep, but irq_set_thread_affinity() is called with desc->lock held
and can be called from hard interrupt context as well. The code has
another bug as it does not hold a ref on the task struct as required
by set_cpus_allowed_ptr().
Just set the IRQTF_AFFINITY bit in action->thread_flags. The next time
the thread runs it migrates itself. Solves all of the above problems
nicely.
Add kerneldoc to irq_set_thread_affinity() while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
The kerneldoc comment describing suspend_device_irqs() is currently
misleading, because generally the function doesn't really disable
interrupt lines at the chip level. Replace it with a more accurate
one.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
LKML-Reference: <200907050022.35117.rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq, irq.h: Fix kernel-doc warnings
genirq: fix comment to say IRQ_WAKE_THREAD
Don't hardcode to node zero for early boot IRQ setup memory allocations.
[ penberg@cs.helsinki.fi: minor cleanups ]
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
Presently non-legacy IRQs have their irq_desc allocated with
kzalloc_node(). This assumes that all callers of irq_to_desc_node_alloc()
will be sufficiently late in the boot process that kmalloc is available.
While porting sparseirq support to sh this blew up immediately, as at the
time that we register the CPU's interrupt vector map only bootmem is
available. Check slab_is_available() to work out which path to use.
[ Impact: fix SH early boot crash with sparseirq enabled ]
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
LKML-Reference: <20090522014008.GA2806@linux-sh.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Trying to implement a driver to use threaded irqs, I was confused when the
return value to use that was described in the comment above
request_threaded_irq was not defined.
Turns out that the enum is IRQ_WAKE_THREAD where as the comment said
IRQ_THREAD_WAKE.
[Impact: do not confuse developers with wrong comments ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <alpine.DEB.2.00.0905121431020.13338@gandalf.stny.rr.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move_irq_desc() will try to move irq_desc to the home node if
the allocated one is not correct, in create_irq_nr().
( This can happen on devices that are on different nodes that
are using MSI, when drivers are loaded and unloaded randomly. )
v2: fix non-smp build
v3: add NUMA_IRQ_DESC to eliminate #ifdefs
[ Impact: improve irq descriptor locality on NUMA systems ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F95EAE.2050903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 044d408409.
The commit added a warning when handle_IRQ_event() is called outside
of hard interrupt context. This breaks the generic tasklet based
interrupt resend mechanism which is used when the hardware has no way
to retrigger the interrupt. So we get a warning for a use case which
is correct and worked for years. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
"tracing: create automated trace defines" causes this compile error on s390,
as reported by Sachin Sant against linux-next:
kernel/built-in.o: In function `__do_softirq':
(.text+0x1c680): undefined reference to `__tracepoint_softirq_entry'
This happens because the definitions of the softirq tracepoints were moved
from kernel/softirq.c to kernel/irq/handle.c. Since s390 doesn't support
generic hardirqs handle.c doesn't get compiled and the definitions are
missing.
So move the tracepoints to softirq.c again.
[ Impact: fix build failure on s390 ]
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
LKML-Reference: <20090429135139.5fac79b8@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This simplifies the node awareness of the code. All our allocators
only deal with a NUMA node ID locality not with CPU ids anyway - so
there's no need to maintain (and transform) a CPU id all across the
IRq layer.
v2: keep move_irq_desc related
[ Impact: cleanup, prepare IRQ code to be NUMA-aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49F65536.2020300@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
irq_set_affinity() and move_masked_irq() try to assign affinity
before calling chip set_affinity(). Some archs are assigning it
in ->set_affinity() again.
We do something like:
cpumask_cpy(desc->affinity, mask);
desc->chip->set_affinity(mask);
But in the failure path, affinity should not be touched - otherwise
we'll end up with a different affinity mask despite the failure to
migrate the IRQ.
So try to update the afffinity only if set_affinity returns with 0.
Also call irq_set_thread_affinity accordingly.
v2: update after "irq, x86: Remove IRQ_DISABLED check in process context IRQ move"
v3: according to Ingo, change set_affinity() in irq_chip should return int.
v4: update comments by removing moving irq_desc code.
[ Impact: fix /proc/irq/*/smp_affinity setting corner case bug ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F65509.60307@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The original feature of migrating irq_desc dynamic was too fragile
and was causing problems: it caused crashes on systems with lots of
cards with MSI-X when user-space irq-balancer was enabled.
We now have new patches that create irq_desc according to device
numa node. This patch removes the leftover bits of the dynamic balancer.
[ Impact: remove dead code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F654AF.8000808@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CPUMASKS_OFFSTACK is not defined anywhere (it is CPUMASK_OFFSTACK).
It is a typo and init_allocate_desc_masks() is called before it set
affinity to all cpus...
Split init_alloc_desc_masks() into all_desc_masks() and init_desc_masks().
Also use CPUMASK_OFFSTACK in alloc_desc_masks().
[ Impact: fix smp_affinity copying/setup when moving irq_desc between CPUs ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <49F6546E.3040406@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When requesting an IRQ, the DEBUG_SHIRQ code executes a fake IRQ just to make
sure the driver is ready to receive an IRQ immediately. The problem was that
this fake IRQ was being executed even if interrupt line failed to be allocated
by __setup_irq.
Signed-off-by: Luis Henriques <henrix@sapo.pt>
LKML-Reference: <20090401170635.GA4392@hades.domain.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ fixed bug pointed out by a warning reported by Stephen Rothwell ]
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up
Create a sub directory in include/trace called events to keep the
trace point headers in their own separate directory. Only headers that
declare trace points should be defined in this directory.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch lowers the number of places a developer must modify to add
new tracepoints. The current method to add a new tracepoint
into an existing system is to write the trace point macro in the
trace header with one of the macros TRACE_EVENT, TRACE_FORMAT or
DECLARE_TRACE, then they must add the same named item into the C file
with the macro DEFINE_TRACE(name) and then add the trace point.
This change cuts out the needing to add the DEFINE_TRACE(name).
Every file that uses the tracepoint must still include the trace/<type>.h
file, but the one C file must also add a define before the including
of that file.
#define CREATE_TRACE_POINTS
#include <trace/mytrace.h>
This will cause the trace/mytrace.h file to also produce the C code
necessary to implement the trace point.
Note, if more than one trace/<type>.h is used to create the C code
it is best to list them all together.
#define CREATE_TRACE_POINTS
#include <trace/foo.h>
#include <trace/bar.h>
#include <trace/fido.h>
Thanks to Mathieu Desnoyers and Christoph Hellwig for coming up with
the cleaner solution of the define above the includes over my first
design to have the C code include a "special" header.
This patch converts sched, irq and lockdep and skb to use this new
method.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As discussed in the thread here:
http://marc.info/?l=linux-kernel&m=123964468521142&w=2
Eric W. Biederman observed:
> It looks like some additional bugs have slipped in since last I looked.
>
> set_irq_affinity does this:
> ifdef CONFIG_GENERIC_PENDING_IRQ
> if (desc->status & IRQ_MOVE_PCNTXT || desc->status & IRQ_DISABLED) {
> cpumask_copy(desc->affinity, cpumask);
> desc->chip->set_affinity(irq, cpumask);
> } else {
> desc->status |= IRQ_MOVE_PENDING;
> cpumask_copy(desc->pending_mask, cpumask);
> }
> #else
>
> That IRQ_DISABLED case is a software state and as such it has nothing to
> do with how safe it is to move an irq in process context.
[...]
>
> The only reason we migrate MSIs in interrupt context today is that there
> wasn't infrastructure for support migration both in interrupt context
> and outside of it.
Yes. The idea here was to force the MSI migration to happen in process
context. One of the patches in the series did
disable_irq(dev->irq);
irq_set_affinity(dev->irq, cpumask_of(dev->cpu));
enable_irq(dev->irq);
with the above patch adding irq/manage code check for interrupt disabled
and moving the interrupt in process context.
IIRC, there was no IRQ_MOVE_PCNTXT when we were developing this HPET
code and we ended up having this ugly hack. IRQ_MOVE_PCNTXT was there
when we eventually submitted the patch upstream. But, looks like I did a
blind rebasing instead of using IRQ_MOVE_PCNTXT in hpet MSI code.
Below patch fixes this. i.e., revert commit 932775a4ab
and add PCNTXT to HPET MSI setup. Also removes copying of desc->affinity
in generic code as set_affinity routines are doing it internally.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Li Shaohua" <shaohua.li@intel.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: "lcm@us.ibm.com" <lcm@us.ibm.com>
Cc: suresh.b.siddha@intel.com
LKML-Reference: <20090413222058.GB8211@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Need to free the old cpumask for affinity and pending_mask.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49D18FF0.50707@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce helper functions allowing us to prevent device drivers from
getting any interrupts (without disabling interrupts on the CPU)
during suspend (or hibernation) and to make them start to receive
interrupts again during the subsequent resume. These functions make it
possible to keep timer interrupts enabled while the "late" suspend and
"early" resume callbacks provided by device drivers are being
executed. In turn, this allows device drivers' "late" suspend and
"early" resume callbacks to sleep, execute ACPI callbacks etc.
The functions introduced here will be used to rework the handling of
interrupts during suspend (hibernation) and resume. Namely,
interrupts will only be disabled on the CPU right before suspending
sysdevs, while device drivers will be prevented from receiving
interrupts, with the help of the new helper function, before their
"late" suspend callbacks run (and analogously during resume).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Delta patch to address the review comments.
- Implement warning when IRQ_WAKE_THREAD is requested and no
thread handler installed
- coding style fixes
Pointed-out-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some devices use devres_request_irq() for to install their interrupt
handler. Add support for threaded interrupts to devres as well.
[tglx - simplified and adapted to latest threadirq version]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for threaded interrupt handlers:
A device driver can request that its main interrupt handler runs in a
thread. To achive this the device driver requests the interrupt with
request_threaded_irq() and provides additionally to the handler a
thread function. The handler function is called in hard interrupt
context and needs to check whether the interrupt originated from the
device. If the interrupt originated from the device then the handler
can either return IRQ_HANDLED or IRQ_WAKE_THREAD. IRQ_HANDLED is
returned when no further action is required. IRQ_WAKE_THREAD causes
the genirq code to invoke the threaded (main) handler. When
IRQ_WAKE_THREAD is returned handler must have disabled the interrupt
on the device level. This is mandatory for shared interrupt handlers,
but we need to do it as well for obscure x86 hardware where disabling
an interrupt on the IO_APIC level redirects the interrupt to the
legacy PIC interrupt lines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Two years migration time is enough. Remove the compability cruft.
Add the deprecated warning in kernel/irq/handle.c because marking
__do_IRQ itself is way too noisy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: cleanup
The code is only compiled if CONFIG_GENERIC_HARDIRQS=y so another
check for this define in the code is redundant. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export the setup_irq() and remove_irq() symbols.
I'd like to export these functions since I have timer
code that needs to use setup_irq() early on (too early
for request_irq()), and the same code can also be
compiled as a module.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120559.2926.82371.sendpatchset@rx1.opensource.se>
[ changed to _GPL as these are special APIs deep inside the irq layer. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Modify remove_irq() to match setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120551.2926.43942.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add new API
This patch adds a remove_irq() function for releasing
interrupts requested with setup_irq().
Without this patch we have no way of releasing such
interrupts since free_irq() today tries to kfree()
the irqaction passed with setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120542.2926.56609.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make sure the genirq layer handlers are indeed running handlers
in hardirq context. That is the genirq expectation and doing
anything else is broken.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1236006812.5330.632.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add new tracepoints
Add them to the generic IRQ code, that way every architecture
gets these new tracepoints, not just x86.
Using Steve's new 'TRACE_FORMAT', I can get function graph
trace as follows using the original two IRQ tracepoints:
3) | handle_IRQ_event() {
3) | /* (irq_handler_entry) irq=28 handler=eth0 */
3) | e1000_intr_msi() {
3) 2.460 us | __napi_schedule();
3) 9.416 us | }
3) | /* (irq_handler_exit) irq=28 handler=eth0 return=handled */
3) + 22.935 us | }
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
'p' stands for pointer - make it clear in setup_irq() and free_irq()
what kind of pointer it is.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus noticed that the 'pp' variable can be eliminated
altogether, and the loop can be cleaned up further.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
- separate out the loop from the actual freeing logic, this wins us
two indentation levels allowing a number of followup prettifications
- turn the WARN_ON() into a more informative WARN().
- clean up the comments and the code flow some more
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
request_irq() calls into proc code via __setup_irq() which is not safe
in an atomic context, so request_irq() can itself use the more
reliable GFP_KERNEL allocation for the action descriptor.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While being at it make every occurrence of 'do_irq_select_affinity'
have the same signature in terms of signedness of the first argument.
Fix this sparse warning:
kernel/irq/manage.c:112:5: warning: symbol 'do_irq_select_affinity' was not declared. Should it be static?
Also rename do_irq_select_affinity() to setup_affinity() - shorter name
and clearer naming.
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simplify and make init_kstat_irqs etc more type proof, suggested by
Andrew.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: get correct kstat_irqs [/proc/interrupts] for msi/msi-x etc
need to call clear_kstat_irqs(), so when we reuse that irq_desc,
we get correct kstat in /proc/interrupts.
This makes /proc/interrupts not have <NULL> entries.
Don't need to worry about arch that doesn't support genirq, because they
will not call dynamic_irq_cleanup().
v2: simplify and make clear_kstat_irqs more robust
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Eric Paris reported:
> I have an hp dl785g5 which is unable to successfully run
> 2.6.29-0.66.rc3.fc11.x86_64 or 2.6.29-rc2-next-20090126. During bootup
> (early in userspace daemons starting) I get the below BUG, which quickly
> renders the machine dead. I assume it is because sparse_irq_lock never
> gets released when the BUG kills that task.
Adjust lock sequence when migrating a descriptor with
CONFIG_NUMA_MIGRATE_IRQ_DESC enabled.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the initialization of irq_default_affinity to early_irq_init as
core_initcall is too late.
irq_default_affinity can be used in init_IRQ and potentially timer and
SMP init as well. All of these happen before core_initcall. Moving
the initialization to early_irq_init ensures that it is initialized
before it is used.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Mike Travis <travis@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In interrupt.h these functions are declared only if
CONFIG_GENERIC_HARDIRQS is set. We should define them under identical
conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide a shared interrupt debug facility under CONFIG_DEBUG_SHIRQ:
it uses the existing irqpoll facilities to iterate through all
registered interrupt handlers and call those which can handle shared
IRQ lines.
This can be handy for suspend/resume debugging: if we call this function
early during resume we can trigger crashes in those drivers which have
incorrect assumptions about when exactly their ISRs will be called
during suspend/resume.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar wrote:
> All non-x86 architectures fail to build:
>
> In file included from /home/mingo/tip/include/linux/random.h:11,
> from /home/mingo/tip/include/linux/stackprotector.h:6,
> from /home/mingo/tip/init/main.c:17:
> /home/mingo/tip/include/linux/irqnr.h:26:63: error: asm/irq_vectors.h: No such file or directory
Do not include asm/irq_vectors.h in generic code - it's not available
on all architectures.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce memory usage.
Allocate kstat_irqs_legacy based on nr_cpu_ids to deal with this
memory usage bump when NR_CPUS bumped from 128 to 4096:
8192 +253952 262144 +3100% kstat_irqs_legacy(.bss)
This is only when CONFIG_SPARSE_IRQS=y.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: Reduce memory usage.
This is the second half of the changes to make the irq_desc_ptrs be
variable sized based on nr_cpu_ids. This is done by adding a new
"max_nr_irqs" macro to irq_vectors.h (and a dummy in irqnr.h) to
return a max NR_IRQS value based on NR_CPUS or nr_cpu_ids.
This necessitated moving the define of MAX_IO_APICS to a separate
file (asm/apicnum.h) so it could be included without the baggage
of the other asm/apicdef.h declarations.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: allocate irq_desc_ptrs in preparation for making it variable-sized.
This addresses this memory usage bump when NR_CPUS bumped from 128 to 4096:
34816 +229376 264192 +658% irq_desc_ptrs(.data.read_mostly)
The patch is split into two parts, the first simply allocates the
irq_desc_ptrs array. Then next will deal with making it variable.
This is only when CONFIG_SPARSE_IRQS=y.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: cleanup WARN msg.
Ingo requested:
> While at it, could you please also convert this to a WARN() construct
> instead? (in a separate commit)
... and it shall be done. ;-)
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: preparation, cleanup, add KERN_INFO printk
Modify references from NR_IRQS to nr_irqs as the later will become
variable-sized based on nr_cpu_ids when CONFIG_SPARSE_IRQS=y.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: fix bug where new irq_desc uses old cpumask pointers which are freed.
As Yinghai pointed out, init_copy_one_irq_desc() copies the old desc to
the new desc overwriting the cpumask pointers. Since the old_desc and
the cpumask pointers are freed, then memory corruption will occur if
these old pointers are used.
Move the allocation of these pointers to after the copy.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Impact: reduce memory usage, use new cpumask API.
Replace the affinity and pending_masks with cpumask_var_t's. This adds
to the significant size reduction done with the SPARSE_IRQS changes.
The added functions (init_alloc_desc_masks & init_copy_desc_masks) are
in the include file so they can be inlined (and optimized out for the
!CONFIG_CPUMASKS_OFFSTACK case.) [Naming chosen to be consistent with
the other init*irq functions, as well as the backwards arg declaration
of "from, to" instead of the more common "to, from" standard.]
Includes a slight change to the declaration of struct irq_desc to embed
the pending_mask within ifdef(CONFIG_SMP) to be consistent with other
references, and some small changes to Xen.
Tested: sparse/non-sparse/cpumask_offstack/non-cpumask_offstack/nonuma/nosmp on x86_64
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: virtualization@lists.osdl.org
Cc: xen-devel@lists.xensource.com
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Impact: clean up sparseirq fallout on random.c
Ingo suggested to change some ifdef from SPARSE_IRQ to GENERIC_HARDIRQS
so we could some #ifdef later if all arch support genirq
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Right now, most of the kernel boot is strictly synchronous, such that
various hardware delays are done sequentially.
In order to make the kernel boot faster, this patch introduces
infrastructure to allow doing some of the initialization steps
asynchronously, which will hide significant portions of the hardware delays
in practice.
In order to not change device order and other similar observables, this
patch does NOT do full parallel initialization.
Rather, it operates more in the way an out of order CPU does; the work may
be done out of order and asynchronous, but the observable effects
(instruction retiring for the CPU) are still done in the original sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
Impact: build fix on ia64
ia64's default_affinity_write() still had old cpumask_t usage:
/home/mingo/tip/kernel/irq/proc.c: In function `default_affinity_write':
/home/mingo/tip/kernel/irq/proc.c:114: error: incompatible type for argument 1 of `is_affinity_mask_valid'
make[3]: *** [kernel/irq/proc.o] Error 1
make[3]: *** Waiting for unfinished jobs....
update it to cpumask_var_t.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: Reduce stack usage, use new cpumask API. ALPHA mod!
Main change is that irq_default_affinity becomes a cpumask_var_t, so
treat it as a pointer (this effects alpha).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'irq-fixes-for-linus-4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sparseirq: move __weak symbols into separate compilation unit
sparseirq: work around __weak alias bug
sparseirq: fix hang with !SPARSE_IRQ
sparseirq: set lock_class for legacy irq when sparse_irq is selected
sparseirq: work around compiler optimizing away __weak functions
sparseirq: fix desc->lock init
sparseirq: do not printk when migrating IRQ descriptors
sparseirq: remove duplicated arch_early_irq_init()
irq: simplify for_each_irq_desc() usage
proc: remove ifdef CONFIG_SPARSE_IRQ from stat.c
irq: for_each_irq_desc() move to irqnr.h
hrtimer: remove #include <linux/irq.h>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, sparseirq: clean up Kconfig entry
x86: turn CONFIG_SPARSE_IRQ off by default
sparseirq: fix numa_migrate_irq_desc dependency and comments
sparseirq: add kernel-doc notation for new member in irq_desc, -v2
locking, irq: enclose irq_desc_lock_class in CONFIG_LOCKDEP
sparseirq, xen: make sure irq_desc is allocated for interrupts
sparseirq: fix !SMP building, #2
x86, sparseirq: move irq_desc according to smp_affinity, v7
proc: enclose desc variable of show_stat() in CONFIG_SPARSE_IRQ
sparse irqs: add irqnr.h to the user headers list
sparse irqs: handle !GENIRQ platforms
sparseirq: fix !SMP && !PCI_MSI && !HT_IRQ build
sparseirq: fix Alpha build failure
sparseirq: fix typo in !CONFIG_IO_APIC case
x86, MSI: pass irq_cfg and irq_desc
x86: MSI start irq numbering from nr_irqs_gsi
x86: use NR_IRQS_LEGACY
sparse irq_desc[] array: core kernel and x86 changes
genirq: record IRQ_LEVEL in irq_desc[]
irq.h: remove padding from irq_desc on 64bits
Impact: fix theoretical NULL dereference
The generic irq layer doesn't know whether irq_chip has ack routine on some
architectures or not. Upon that, before calling chip->ack, we should check
that it's not NULL.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
GCC has a bug with __weak alias functions: if the functions are in
the same compilation unit as their call site, GCC can decide to
inline them - and thus rob the linker of the opportunity to override
the weak alias with the real thing.
So move all the IRQ handling related __weak symbols to kernel/irq/chip.c.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot crash if the kernel is built with certain GCC versions
GCC has a bug with __weak alias functions: if the functions are in
the same compilation unit as their call site, GCC can decide to
inline them - and thus rob the linker of the opportunity to override
the weak alias with the real thing.
This can lead to the boot crash reported by Kamalesh Babulal:
ACPI: Core revision 20080926
Setting APIC routing to flat
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
IP: [<ffffffff8021f9a8>] add_pin_to_irq_cpu+0x14/0x74
PGD 0
Oops: 0000 [#1] SMP
[...]
So move the arch_init_chip_data() function from handle.c to manage.c.
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix hang
Suresh report his two sockets system only works with SPARSE_IRQ enable
it turns out we miss the setting desc->irq
so provide early_irq_init() even !SPARSE_IRQ to set desc->irq
Reported-by: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add lockdep annotation to legacy IRQ descs
Warnings resulting out of this were not seen in practice, but it's prudent
to initialize the legacy descriptors to the lock class as well, symmetric
to how we do it with other descriptors.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix panic on null pointer with sparseirq
Some GCC versions seem to inline the weak global function,
when that function is empty.
Work it around, by making the functions return a (dummy) integer.
Signed-off-by: Yinghai <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
init_one_irq_desc() does not initialize the desc->lock properly -
you cannot init a lock by memcpying some other lock on it.
This happens to work right now (because irq_desc_init is never in use),
but it's a dangerous construct nevertheless, so fix it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce printk noise
There were a couple of leftover KERN_DEBUG debugging printks, remove
them. Also clarify an error message.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
