* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits)
atmel-mci: add MCI2 register definitions
atmel-mci: Integrate AT91 specific definition in header file
tmio_mmc: allow compilation for ASIC3
mmc_block: do not DMA to stack
sdhci: Print ADMA status and pointer on debug
tmio_mmc: fix clock setup
tmio_mmc: map SD control registers after enabling the MFD cell
tmio_mmc: correct probe return value for num_resources != 3
tmio_mmc: don't use set_irq_type
tmio_mmc: add bus_shift support
MFD,mmc: tmio_mmc: make HCLK configurable
mmc_spi: don't use EINVAL for possible transmission errors
cb710: more cleanup for the DEBUG case.
sdhci: platform driver for SDHCI
mxcmmc: remove frequency workaround
cb710: handle DEBUG define in Makefile
cb710: add missing parenthesis
cb710: fix printk format string
mmc: Driver for CB710/720 memory card reader (MMC part)
pxamci: add regulator support.
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
New revision of Atmel MCI interface adds new features. This is a update of
register definition in header file. This new MCI IP is called MCI2.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The MCI IP is shared among AVR32 and AT91 SOCs.
AT91 has specific bit definitions in the user interface of MCI SD/MMC IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
In the write recovery routine, the data to get from the card
is allocated from the stack. The DMA mapping documentation says
explicitly stack memory is not mappable by any of the DMA calls.
Change to using kmalloc() to allocate the memory for the result
from the card and then free it once we've finished with the
transaction.
[ Changed to GFP_KERNEL allocation - Pierre Ossman ]
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
If using ADMA, then we should print the ADMA error
and current pointer in sdhci_dumpregs() when any
debug is requested.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch fixes the clock setup in tmio_mmc.
* Incorrect divider setting
* Cruft written to the clock registers (seemingly harmless but Not
Good (tm))
It also eliminates some unnecessary ifs and tidies the loop syntax.
Thanks to Philipp Zabel who discovered the divider issue, commenting
"Except for the SDCLK = HCLK (divider bypassed) case, the clock
setting resulted in double the requested frequency.
The smallest possible frequency (f_max/512) is configured with
a divider setting 0x80, not 0x40."
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
ASIC3 can disable the memory, so we need to wait for mfd_cell->enable
to enable the memory before we can map the SD control registers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Use an IRQF_TRIGGER_ flag in request_irq instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Added a platform driver which uses the SDHCI core.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text. This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Freescale eSDHC controller has the special order for
the HOST version register. that is not same as the other's
registers. The address of HOSTVER in spec is 0xFE, and
we need use the in_be16(0xFE) to access it, not in_be16(0xFC).
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Especially with Sandisk SDHC cards, the second SWITCH command was failing
with a timeout and the card was not recognized at all. However if the
system was busy, or debugging was enabled, or a udelay(100) was inserted
before the second SWITCH command in the core code, then the timing was
so that the card started to work.
With some unusual block sizes, the data FIFO status doesn't indicate a
"empty" state right away when the data transfer is done. Queuing
another data transfer in that condition results in a transfer timeout.
The empty FIFO bit eventually get set by itself in less than 50 usecs
when it is not set right away. So let's just poll for that bit before
configuring the controller with a new data transfer.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Empirical evidences show that this is causing far more problems than it
solves when this mode is enabled in the host hardware. Amongst those
cards that are known to be non functional when this bit is set are:
A-Data "Speedy" 2GB SD card
Kodak 512MB SD card
Ativa 1GB MicroSD card
Marvell 8688 (WIFI/Bluetooth) SDIO card
Since those cards do work on other host controllers which do honnor the
hs timing, the issue must be with this particular host hardware.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
disable_irq() should wait for all running handlers to complete
before returning. As such, if it's used to disable an interrupt
from that interrupt's handler it will deadlock. This replaces
the dangerous instances with the _nosync() variant which doesn't
have this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
We plan to use fsl,esdhc going forward as the base compatible so update
the driver to bind against it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
When a software timeout occurs in polling mode hardware was left in
an indeterminate state causing subsequent operations to block.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
This is a temporary workaround until the MMC stack can be fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
