1
Commit Graph

685 Commits

Author SHA1 Message Date
Javier Cardona
24bdd9f4c9 mac80211: Rename mesh_params to mesh_config to prepare for mesh_setup
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20 14:46:57 -05:00
Luis R. Rodriguez
2784fe915c cfg80211: fix null pointer dereference with a custom regulatory request
Once we moved the core regulatory request to the queue and let
the scheduler process it last_request will have been left NULL
until the schedular decides to process the first request. When
this happens and we are loading a driver with a custom regulatory
request like all Atheros drivers we end up with a NULL pointer
dereference. We fix this by checking if the request was a
custom one.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
PGD 71f91067 PUD 712b2067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/firmware/2-1/loading
CPU 0
Modules linked in: ath9k_htc(+) ath9k_common ath9k_hw ath <etc>
Pid: 3094, comm: insmod Tainted: G        W   2.6.37-rc5-wl #16 INVALID/28427ZQ
RIP: 0010:[<ffffffffa016de87>]  [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
RSP: 0018:ffff88007045db78  EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffffffa047d9a0 RCX: ffff88007045dbd0
RDX: 0000000000004e20 RSI: 000000000024cde0 RDI: ffff8800700483e0
RBP: ffff88007045db98 R08: ffffffffa02f5b40 R09: 0000000000000001
R10: 000000000000000e R11: 0000000000000001 R12: 0000000000000000
R13: ffff88007004e3b0 R14: 0000000000000000 R15: ffff880070048340
FS:  00007f635a707700(0000) GS:ffff880077400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000004 CR3: 00000000708a9000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process insmod (pid: 3094, threadinfo ffff88007045c000, task ffff8800713e3ec0)
Stack:
 ffffffffa047d9a0 0000000000000000 ffff88007004e3b0 0000000000000000
 ffff88007045dc08 ffffffffa016e147 000000007045dc08 0000000000000002
 ffff8800700483e0 ffffffffa02f5b40 ffff88007045dbd8 0000000000000000
Call Trace:
 [<ffffffffa016e147>] wiphy_apply_custom_regulatory+0x137/0x1d0 [cfg80211]
 [<ffffffffa047a690>] ? ath9k_reg_notifier+0x0/0x50 [ath9k_htc]
 [<ffffffffa02f47f7>] ath_regd_init+0x347/0x430 [ath]
 [<ffffffffa047b1f5>] ath9k_htc_probe_device+0x6c5/0x960 [ath9k_htc]
 [<ffffffffa0472a2c>] ath9k_htc_hw_init+0xc/0x30 [ath9k_htc]
 [<ffffffffa04747e6>] ath9k_hif_usb_probe+0x216/0x3b0 [ath9k_htc]
 [<ffffffffa03bb6bc>] usb_probe_interface+0x10c/0x210 [usbcore]
 [<ffffffff812aec26>] driver_probe_device+0x96/0x1c0
 [<ffffffff812aedf3>] __driver_attach+0xa3/0xb0
 [<ffffffff812aed50>] ? __driver_attach+0x0/0xb0
 [<ffffffff812adaae>] bus_for_each_dev+0x5e/0x90
 [<ffffffff812ae8c9>] driver_attach+0x19/0x20
 [<ffffffff812ae438>] bus_add_driver+0x168/0x320
 [<ffffffff812af071>] driver_register+0x71/0x140
 [<ffffffff811fc4a8>] ? __raw_spin_lock_init+0x38/0x70
 [<ffffffffa03ba39c>] usb_register_driver+0xdc/0x190 [usbcore]
 [<ffffffffa03a2000>] ? ath9k_htc_init+0x0/0x4f [ath9k_htc]
 [<ffffffffa047499e>] ath9k_hif_usb_init+0x1e/0x20 [ath9k_htc]
 [<ffffffffa03a202b>] ath9k_htc_init+0x2b/0x4f [ath9k_htc]
 [<ffffffff8100212f>] do_one_initcall+0x3f/0x180
 [<ffffffff8109ef5b>] sys_init_module+0xbb/0x200
 [<ffffffff8100bf52>] system_call_fastpath+0x16/0x1b
Code: <etc, who cares>
RIP  [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
 RSP <ffff88007045db78>
CR2: 0000000000000004
---[ end trace 79e4193601c8b713 ]---

Reported-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16 15:22:31 -05:00
Jouni Malinen
cf4e594ea7 nl80211: Add notification for dropped Deauth/Disassoc
Add a new notification to indicate that a received, unprotected
Deauthentication or Disassociation frame was dropped due to
management frame protection being in use. This notification is
needed to allow user space (e.g., wpa_supplicant) to implement
SA Query procedure to recover from association state mismatch
between an AP and STA.

This is needed to avoid getting stuck in non-working state when MFP
(IEEE 802.11w) is used and a protected Deauthentication or
Disassociation frame is dropped for any reason. After that, the
station would silently discard any unprotected Deauthentication or
Disassociation frame that could be indicating that the AP does not
have association for the STA (when the Reason Code would be 6 or 7).
IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism.

Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16 15:22:30 -05:00
Johannes Berg
a293911d4f nl80211: advertise maximum remain-on-channel duration
With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15 17:03:56 -05:00
Johannes Berg
dbd2fd656f cfg80211/nl80211: separate unicast/multicast default TX keys
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.

Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13 15:23:28 -05:00
Sven Neumann
01123e2331 cfg80211: update information elements in cached BSS struct
When a cached BSS struct is updated because a new beacon was received,
the code replaces the cached information elements by the IEs from the
new beacon. However it did not update the pub.information_elements
and pub.len_information_elements fields leaving them either pointing
to the old beacon IEs or in an inconsistent state where the data is
replaced by the new beacon IEs but len_information_elements still has
its value from the first beacon.

Fix this by updating the information elements fields if they are
pointing to beacon IEs.

Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13 15:23:28 -05:00
Bruno Randolf
a7ffac9591 cfg80211: Add antenna availability information
Add a field to wiphy for the hardware to report the availble antennas for
configuration. Only if this is set to something bigger than zero, will the
anntenna configuration ops be executed.

Allthough this could be a simple number of antennas, I defined it as a bitmap
of antennas which are available for configuration, since it's more consistent
with the rest of the antenna API and there could be cases where the
hardware allows only configuration of certain antennas. As it does not make
much of a difference in size or normal usage, I think it's better to be able to
support this, in case the need arises.

The antenna configuration is now also checked against the availabe antennas and
rejected if it does not match.

Signed-off-by: Bruno Randolf <br1@einfach.org>

--
v3:	always apply available antenna mask (for "all" antennas case).

v2:	reject antenna configurations which don't match the available antennas
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13 15:23:27 -05:00
Helmut Schaa
50b12f597b cfg80211: Add new BSS attribute ht_opmode
Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-08 15:38:43 -05:00
Bruno Randolf
541a45a142 nl80211/mac80211: Report signal average
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.

This uses the recently added generic EWMA library function.

--
v2:	fix ABI breakage and change factor to be a power of 2.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 16:09:12 -05:00
Johannes Berg
29cbe68c51 cfg80211/mac80211: add mesh join/leave commands
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.

Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.

We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.

In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06 16:01:29 -05:00
Johannes Berg
bd90fdcc5f nl80211: refactor mesh parameter parsing
I'm going to need this in a new place later.

Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06 16:01:29 -05:00
Johannes Berg
f9e10ce4cf cfg80211: require add_virtual_intf to return new dev
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.

Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06 16:01:28 -05:00
Javier Cardona
45904f2165 nl80211/mac80211: define and allow configuring mesh element TTL
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames.  Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06 16:01:28 -05:00
Johannes Berg
f7ca38dfe5 nl80211/cfg80211: extend mgmt-tx API for off-channel
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.

However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-29 15:24:35 -05:00
Johannes Berg
c063dbf52b cfg80211: allow using CQM event to notify packet loss
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:36 -05:00
Felix Fietkau
dd5b4cc71c cfg80211/mac80211: improve ad-hoc multicast rate handling
- store the multicast rate as an index instead of the rate value
  (reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:35 -05:00
Joe Perches
e9c0268f02 net/wireless: Use pr_<level> and netdev_<level>
No change in output for pr_<level> prefixes.
netdev_<level> output is different, arguably improved.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:33 -05:00
John W. Linville
d7a066c923 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2010-11-24 16:19:24 -05:00
John W. Linville
ccb1435401 Revert "nl80211/mac80211: Report signal average"
This reverts commit 86107fd170.

This patch inadvertantly changed the userland ABI.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:18:36 -05:00
Luis R. Rodriguez
b2e253cf30 cfg80211: Fix regulatory bug with multiple cards and delays
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.

We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.

This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.

Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.

This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:

       #!/bin/bash
       echo $COUNTRY >> /tmp/log
       sleep 2
       /sbin/crda.orig

And these regulatory tests:

       modprobe mac80211_hwsim regtest=2
       modprobe mac80211_hwsim regtest=3

Reported-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:48:51 -05:00
Luis R. Rodriguez
b0e2880b05 cfg80211: move mutex locking to reg_process_pending_hints()
This will be required in the next patch and it makes the
next patch easier to review.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:48:50 -05:00
Luis R. Rodriguez
f333a7a2f4 cfg80211: move reg_work and reg_todo above
These will be used earlier in the next few patches.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:48:50 -05:00
Luis R. Rodriguez
31e99729ae cfg80211: put core regulatory request into queue
This will simplify the synchronization for pending requests.
Without this we have a race between the core and when we
restore regulatory settings, although this is unlikely
its best to just avoid that race altogether.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:48:50 -05:00
Bruno Randolf
86107fd170 nl80211/mac80211: Report signal average
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.

This uses the recently added generic EWMA library function.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18 14:22:20 -05:00
Mark Mentovai
09a02fdb91 cfg80211: fix can_beacon_sec_chan, reenable HT40
This follows wireless-testing 9236d838c9
("cfg80211: fix extension channel checks to initiate communication") and
fixes accidental case fall-through. Without this fix, HT40 is entirely
blocked.

Signed-off-by: Mark Mentovai <mark@moxienet.com>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18 11:35:05 -05:00
Felix Fietkau
885a46d0f7 cfg80211: add support for setting the ad-hoc multicast rate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:39:08 -05:00
Bruno Randolf
afe0cbf875 cfg80211: Add nl80211 antenna configuration
Allow setting of TX and RX antennas configuration via nl80211.

The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.

Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.

Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.

802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.

Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.

While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:

1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).

2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).

3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.

Signed-off-by: Bruno Randolf <br1@einfach.org>

--
v7:	Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:05 -05:00
Luis R. Rodriguez
9236d838c9 cfg80211: fix extension channel checks to initiate communication
When operating in a mode that initiates communication and using
HT40 we should fail if we cannot use both primary and secondary
channels to initiate communication. Our current ht40 allowmap
only covers STA mode of operation, for beaconing modes we need
a check on the fly as the mode of operation is dynamic and
there other flags other than disable which we should read
to check if we can initiate communication.

Do not allow for initiating communication if our secondary HT40
channel has is either disabled, has a passive scan flag, a
no-ibss flag or is a radar channel. Userspace now has similar
checks but this is also needed in-kernel.

Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 15:59:39 -05:00
Luis R. Rodriguez
d91e41b690 cfg80211: prefix REG_DBG_PRINT() with cfg80211
Everyone's doing it, its the cool thing.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:15 -05:00
Luis R. Rodriguez
e702d3cf29 cfg80211: add debug print when processing a channel
In the worst case you are seeing really odd things you want
more information than what is provided right now, for those
that insist and want debug info through CONFIG_CFG80211_REG_DEBUG
provide a print of when we are processing a channel and with what
regulatory rule.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:14 -05:00
Luis R. Rodriguez
a65185367f cfg80211: add debug print when disabling a channel on a custom regd
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:13 -05:00
Luis R. Rodriguez
926a0a094d cfg80211: add debug prints for when we ignore regulatory hints
This can help with debugging issues. You will only see
these with CONFIG_CFG80211_REG_DEBUG enabled.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:12 -05:00
Luis R. Rodriguez
ca4ffe8f28 cfg80211: fix disabling channels based on hints
After a module loads you will have loaded the world roaming regulatory
domain or a custom regulatory domain. Further regulatory hints are
welcomed and should be respected unless the regulatory hint is coming
from a country IE as the IEEE spec allows for a country IE to be a subset
of what is allowed by the local regulatory agencies.

So disable all channels that do not fit a regulatory domain sent
from a unless the hint is from a country IE and the country IE had
no information about the band we are currently processing.

This fixes a few regulatory issues, for example for drivers that depend
on CRDA and had no 5 GHz freqencies allowed were not properly disabling
5 GHz at all, furthermore it also allows users to restrict devices
further as was intended.

If you recieve a country IE upon association we will also disable the
channels that are not allowed if the country IE had at least one
channel on the respective band we are procesing.

This was the original intention behind this design but it was
completely overlooked...

Cc: David Quan <david.quan@atheros.com>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:10 -05:00
Luis R. Rodriguez
749b527b21 cfg80211: fix allowing country IEs for WIPHY_FLAG_STRICT_REGULATORY
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.

This was part of the original design, however it was completely
overlooked...

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:09 -05:00
Luis R. Rodriguez
7ca43d03b1 cfg80211: pass the reg hint initiator to helpers
This is required later.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:08 -05:00
Felix Fietkau
3cc25e510d cfg80211: fix a crash in dev lookup on dump commands
IS_ERR and PTR_ERR were called with the wrong pointer, leading to a
crash when cfg80211_get_dev_from_ifindex fails.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08 16:53:47 -05:00
Luis R. Rodriguez
a171fba491 cfg80211: fix regression on processing country IEs
The patch 4f366c5:

	wireless: only use alpha2 regulatory information from country IE

removed some complex intersection we were always doing between the AP's
country IE info and what we got from CRDA. When CRDA sent us back a
regulatory domain we would do some sanity checks on that regulatory
domain response we just got. Part of these sanity checks included
checking that we already had performed an intersection for the
request of NL80211_REGDOM_SET_BY_COUNTRY_IE type.

This mean that cfg80211 was only processing country IEs for cases
where we already had an intersection, but since we removed enforcing
this this is no longer required, we should just apply the country
IE country hint with the data received from CRDA.

This patch has fixes intended for kernels >= 2.6.36.

Cc: stable@kernel.org
Reported-by: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-25 14:43:14 -04:00
Linus Torvalds
5f05647dd8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
  bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
  vlan: Calling vlan_hwaccel_do_receive() is always valid.
  tproxy: use the interface primary IP address as a default value for --on-ip
  tproxy: added IPv6 support to the socket match
  cxgb3: function namespace cleanup
  tproxy: added IPv6 support to the TPROXY target
  tproxy: added IPv6 socket lookup function to nf_tproxy_core
  be2net: Changes to use only priority codes allowed by f/w
  tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
  tproxy: added tproxy sockopt interface in the IPV6 layer
  tproxy: added udp6_lib_lookup function
  tproxy: added const specifiers to udp lookup functions
  tproxy: split off ipv6 defragmentation to a separate module
  l2tp: small cleanup
  nf_nat: restrict ICMP translation for embedded header
  can: mcp251x: fix generation of error frames
  can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
  can-raw: add msg_flags to distinguish local traffic
  9p: client code cleanup
  rds: make local functions/variables static
  ...

Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
2010-10-23 11:47:02 -07:00
Linus Torvalds
092e0e7e52 Merge branch 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
  vfs: make no_llseek the default
  vfs: don't use BKL in default_llseek
  llseek: automatically add .llseek fop
  libfs: use generic_file_llseek for simple_attr
  mac80211: disallow seeks in minstrel debug code
  lirc: make chardev nonseekable
  viotape: use noop_llseek
  raw: use explicit llseek file operations
  ibmasmfs: use generic_file_llseek
  spufs: use llseek in all file operations
  arm/omap: use generic_file_llseek in iommu_debug
  lkdtm: use generic_file_llseek in debugfs
  net/wireless: use generic_file_llseek in debugfs
  drm: use noop_llseek
2010-10-22 10:52:56 -07:00
John W. Linville
c64557d666 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem 2010-10-15 16:11:56 -04:00
Johannes Berg
9ebad4ab87 radiotap: fix vendor namespace parsing
There's a bug with radiotap vendor namespace
parsing if you don't register for the given
namespace extensions. Fix this by passing
only the unknown vendor namespaces and the
registered data to frontends, but not both.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-15 15:57:34 -04:00
Arnd Bergmann
6038f373a3 llseek: automatically add .llseek fop
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.

The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.

New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time.  Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.

The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.

Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.

Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.

===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
//   but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}

@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}

@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
   *off = E
|
   *off += E
|
   func(..., off, ...)
|
   E = *off
)
...+>
}

@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}

@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
  *off = E
|
  *off += E
|
  func(..., off, ...)
|
  E = *off
)
...+>
}

@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}

@ fops0 @
identifier fops;
@@
struct file_operations fops = {
 ...
};

@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
 .llseek = llseek_f,
...
};

@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
 .read = read_f,
...
};

@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
 .write = write_f,
...
};

@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
 .open = open_f,
...
};

// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
...  .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};

@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
...  .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};

// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
...  .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};

// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};

// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};

@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+	.llseek = default_llseek, /* write accesses f_pos */
};

// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////

@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
 .write = write_f,
 .read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};

@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};

@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};

@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
2010-10-15 15:53:27 +02:00
Johannes Berg
271733cf84 cfg80211: notify drivers about frame registrations
Drivers may need to adjust their filters according
to frame registrations, so notify them about them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-13 15:45:22 -04:00
Ben Greear
cfd8e12f42 wireless: Print wiphy name in sysfs.
The index cannot be used to reliably reconstruct a phy
name, so explicitly add the phy name to sysfs so that scripts
can figure out the parent phy device for a particular
wireless interface.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-12 16:05:29 -04:00
Felix Fietkau
8610c29a2c cfg80211: add channel utilization stats to the survey command
Using these, user space can calculate a relative channel utilization
with arbitrary intervals by regularly taking snapshots of the survey
results.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-11 15:04:20 -04:00
Ben Greear
5a5c731aa5 wireless: Set some stats used by /proc/net/wireless (wext)
Some stats for /proc/net/wireless (and wext in general) are not
being set.  This patch addresses a few of those with values easily
obtained from mac80211 core.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-11 15:04:19 -04:00
Johannes Berg
7623225f90 Revert "wireless: Use first phyX name available when registering phy devices."
This reverts commit 5a254ffe3f.

The commit failed to take into account that allocated wireless devices
(wiphys) are not added into the device list upon allocation, but only
when they are registered. Therefore, it opened up a race between
allocating and registering a name, so that if two processes allocate and
register concurrently ("alloc, alloc, register, register" rather than
"alloc, register, alloc, register") the code will attempt to use the
same name twice.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-10-11 14:46:52 -04:00
John W. Linville
e9a68707d7 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/net/wireless/ipw2x00/ipw2200.c
2010-10-08 15:39:28 -04:00
Johannes Berg
388ac775be cfg80211: constify WDS address
There's no need for the WDS peer address
to not be const, so make it const.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-07 14:41:28 -04:00
Johannes Berg
43b19952de nl80211: use new genl helpers for WDS
Bill Jordan's patch to allow setting the WDS
peer crossed with my patch removing all the
boilerplate code in nl80211, and consequently
he didn't make use of it yet. Fix that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-07 14:41:27 -04:00