This patch fixes the following warning:
arch/arm/mach-davinci/board-sffsdr.c:99: warning: 'sffsdr_emac_pdata' defined but not used
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A section mismatch is reported for gpio_led_platform_data
as it is referenced by a non annotated function (evm_led_setup)
This patch fixes the issue by converting the __initconst to const
as is the case in arch/arm/mach-davinci/board-dm644x-evm.c file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Include high speed capabilities in MMC/SD platform data
for DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using a device_initcall() for initializing the voltage regulator
on DA850 is not such a good idea because it gets called for all
platforms - even those who do not have a regulator implemented.
This leads to a big fat warning message during boot-up when
regulator cannot be found.
Instead, tie initialization of voltage regulator to cpufreq init.
Define a platform specific init call which in case of DA850 gets
used for initializing the regulator. On other future platforms it
can be used for other purposes.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch provides a function to help register cpuidle driver
on da8xx/omap-l1xx platforms.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds support for DaVinci cpu idle driver.
Two idle states are defined:
1. Wait for interrupt
2. Wait for interrupt and DDR self-refresh (or power down)
Some DaVinci SoCs support putting DDR in self-refresh (eg Dm644x, DM6467)
while others support putting DDR in self-refresh and power down (eg DM35x,
DA8xx).
Putting DDR (or mDDR) in power down saves more power than self-refresh.
The patch has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y
option, using da8xx_omapl_defconfig, some warnings are
observed:
WARNING: vmlinux.o(.text+0xc2a4): Section mismatch in reference
from the function da850_evm_setup_nor_nand() to the variable
.init.data:da850_nand_pins
The function da850_evm_setup_nor_nand() references
the variable __initdata da850_nand_pins.
This is often because da850_evm_setup_nor_nand lacks a __initdata
annotation or the annotation of da850_nand_pins is wrong.
This patch fixes such warnings.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Eliminate the static function declaration by rearranging
data in da850/omap-l138 board file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are multiple steps in configuring the EMAC to MII or RMII mode.
Current code implements them using multiple checks.
Consolidate the multiple checks into a single if construct.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Get rid of DA850_UI_EXP config option since it is not used anywhere
else in code.
Instead make the UI expander choice menu dependent on the EVM
selection itself.
Also add help text indicating that UI board is actually detected
automatically.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Implement autodetection of RMII PHY by shifting the decision
to use the RMII PHY to da850_evm_ui_expander_setup() from
da850_evm_init() earlier.
Without this patch, selecting RMII PHY in the UI expander menu
will make the MII PHY unusable even though UI board is not
connected.
The actual configuration and registration of the EMAC device
is delayed to device_initcall() so it happens after the UI card
detection is complete.
A side effect of this patch is the removal of a voilation of
Documentation/SubmittingPatches section 2.2 in function
da850_evm_init()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On the DA830, AEMIF and MMC/SD pins are shared. On the EVM, when
the mux_mode signal is low MMC/SD works and when mux_mode signal
is high, NAND works.
When MMC/SD driver is configured in the kernel, do not let NAND
get registered and drive mux_mode high. Instead, print a warning
for user to understand why the platform device for NAND did not
get registered.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch supports runtime detection of DA830 UI card and
eliminates the need for DA830_UI config option. Successful
probe of GPIO expander present on the UI card is used to
detect its presence. For this reason, GPIO_PCF857X is auto-
selected when DA830 EVM is configured. In case the UI card
is absent, the probe fails in reasonable time.
As a side effect this patch also gets rid of the voilation
of Documentation/SubmittingPatches section 2.2 in function
da830_evm_ui_expander_setup()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove ifdefs inside da830_evm_init function since they are
discouraged in Documentation/SubmittingPatches section 2.2
Use the method outlined in that document for fixing it.
Tested on DA830 EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes the following warning seen when building with default
config:
arch/arm/mach-davinci/board-da830-evm.c:371: warning: 'da830_evm_devices' defined but not used
Tested on DA830 EVM with and without CONFIG_DA830_UI_NAND enabled.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for NAND flash parts on the DA830/OMAP-L137 EVM
User Interface board. This includes overriding the default
bad block tables used by the davinci_nand driver.
Signed-off-by: David A. Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Properly set up the OTG mode thru the CFGCHIP2 register, enable the
USB0_DRVVBUS pin, and finally register the MUSB platform device.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the function to register the MUSB platform device.
Additional compile warning fixes by Sekhar Nori.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename setup_usb() into davinci_setup_usb(). While at it:
- move its declaration from <mach/common.h> to more fitting <mach/usb.h>;
- teach it to handle values of the 'mA' parameter greater than 510 and thus
pass 1000 instead of 500 for the power switches capable of sourcing over 1 A;
- teach it to handle odd values of the 'potpgt_ms' parameter...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
DMx:
- enable MMC and dm365evm_keys
- Enable DM355 and DM365 input drivers as modules.
da8xx
- combine da830 and da850 into common defconfig
- drop SYSFS_DEPRECATED flag
- auto-select D$ writethrough for da830
- enable CPUfreq and FB
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In the McASP clock definition add a flag to indicate that the peripheral clock
belongs to ASYNC3 clock domain.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data and partition info for NAND on dm6467 EVM.
Note that the partition layout is dependent on the UBL, U-Boot etc. used. This
patch tries to minimize that dependency by setting first partition for UBL,
U-Boot and environment altogether.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes it easier to identify SoC init failures
by panicing when SoC init fails. Without successful SoC
init, the kernel eventually fails when attempt is made to
access the clocks.
Also, an error is printed when JTAG ID match fails to make
it easier to identify failures due to SoC rev changes.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.
This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM can be connected to an UI card which has various
peripherals on it.The UI card has TCA6416 expander which can be probed
to check whether the UI card is connected or not. If the UI card is
connected, setup NOR and NAND devices. This is done via the expander
setup callback.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Replace badly chosen 'psc_ctlr' name of the 'struct clk' field (PSC already
means "Power and Sleep Controller", so the '_ctlr' postfix makes the name
tautological) with technically correct 'gpsc' (Global PSC -- which contains
all the module registers).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for using the TPS65070 PMIC found
on the DA850/OMAP-L138 EVM.
It defines the power rail consumer mapping and registers the
the I2C based PMIC as a board device.
The power rail constraints are derived from the maxmimum and
minimum recommended operating condition values of the respective
consumers derived from section 5.2 of the OMAP-L138 datasheet.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for regulating the CVDD voltage for the
DA850/OMAP-L138 platform.
The CVDD min and max values for each OPP have been obtained from
section 5.2 "Recommended Operating Conditions" of SPRS586
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds basic frequency scaling support for DA850/OMAP-L138.
Currently, frequency scaling only on PLL0 is supported. No scaling of PLL1
as yet.
Peripherals like MMC/SD which have a clock input synchronous with
ARM clock will not work well since the clock will change behind their backs.
Support for notification to such devices to adjust themselves to the
new frequency will be added in later patches. Current defconfigs keep
CPUFreq disabled so it will not affect normal operation.
The OPP defintions assume clock input of 24MHz to the SoC. This is inline
with hardcoding of input frequency in the <soc>.c files. At some point
this will need to move into board dependent code as new boards appear with
a different reference clock.
Tested on OMAP-L138 EVM with ondemand governer and a shell script to
vary processor load.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a basic CPUFreq driver for DaVinci devices registering with the
kernel CPUFreq infrastructure.
Support is added for both frequency and voltage regulation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Newer revs of da830 silicon have different 'variant' field of the JTAG
id register. Current code only supports rev 1.0 silicon.
This patch adds support for rev1.1 and rev2.0 silicon and updates
the 'name' strings to add a '-' between 'omap' & 'l137' to have
consistent naming with da850/omap-l138.
From Mark Grosen <mgrosen@ti.com>:
"There are currently three silicon revisions for OMAPL137. The JTAG IDs
(DEVIDR register contents) for each silicon revision are shown below:
0x0B7D F02F for silicon revision 1.0
0x8B7D F02F for silicon revision 1.1
0x9B7D F02F for silicon revision 2.0
Corresponding errata documentation will be available in the next few
weeks on the ti.com website."
Reported-by: Nick Thompson <Nick.Thompson@gefanuc.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The machine name string shows up in /proc/cpuinfo under 'Hardware' and
can be used by userspace apps. Make the format consistent with the
DA850/OMAP-l138 EVM by adding the '-' between OMAP and L137.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On this board the OHCI port's power control and over-current signals from
TPS2065 power switch are connected via GPIO1[15] and GPIO2[1] respectively,
so we can implement the DA8xx OHCI glue layer's hooks for overriding the
root hub port's power and over-current status bits.
We also have to properly set up the clocking mode in the CFGCHIP2 register,
so that internal 24 MHz reference clock is fed to the USB 2.0 (MUSB) PHY and
its output is used to clock the USB 1.1 (OHCI) PHY...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the function to register the OHCI platform device, given the root hub
related platform data passed from the board specific code. The platfrom
data provide for overriding the OHCI port power and over-current bits at
the board level.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
These are needed by the MUSB and OHCI glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch itself does not change the functionality of
any existing code. PARAM entries in the present GIT kernel
are referred to as slots. New API's being added to the
EDMA driver were referring to these PARAM entries as
"params". This patch updates the terminolgy used in the
EDMA driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The reserve_contiguous_params function is used to reserve
a set of contiguous PARAMs. If we do not find a complete
set of contiguous PARAMs, the functions still has to free
every PARAM that it found to be free in the process of finding a
complete set and thus marked as "in use".
This patch mainly deals with correctly handling the
freeing of PARAMs.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch updates the NAND driver platform data to use 4-bit ECC and the
ECC_HW/ECC_HW_OOB_FIRST modes.
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch updates the NAND driver platform data to use 4-bit ECC and the
ECC_HW/ECC_HW_OOB_FIRST modes.
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The edma_alloc_cont_slots API is used for obtaining a set of
contiguous slots. When we use the "_ANY" option with this
API, by definition of this option it is suppossed to start
looking for a set of contiguous slots starting from slot 64 for
DaVinci SOC's and 32 for DA8xx SOC's. This has been explained in
the API description in the driver itself. So when we use the
"_ANY" option with this API, the slot number passed as
an argument should be a "don't care".
This patch takes care of this condition mentioned above.
When checking to see if the starting slot is a valid number,
it checks to make sure that the "_ANY" option is not used.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In the edma_free_cont_slots API, the variable slot was being modified
and then used in the for loop.
This results in incorrect behaviour when the API is used.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin
number of LCD panel power has changed. This patch takes
care of this change. Software will support only Beta
versions of DA850/OMAP-L138 EVM.
In the process, add the missing entry for data pin 0
and remove the GPIO specific pins from da850_lcdcntl_pins
structure. EVM specific muxing for LCD is being done in the
board file now.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add RTC support for the da830/omap-l137 and da850/omap-l138
SoC's by leveraging existing the rtc-omap driver.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add graphics support for the Sharp LCD035Q3DG01 graphical
LCD that's on the User Interface (UI) daughter card of the
DA830/OMAP-L137 EVM.
The LCD shares EMIFA lines with the NAND and NOR devices that
are also on the UI card so those lines are shared via a couple
of muxes. The muxes are controlled by the 'MUX_MODE' line on
the UI card. The 'MUX_MODE' line is controlled by pin P6 of
a pcf8574 i2c expander that's at i2c address 0x3f on UI card.
The i2c expander is controlled using the gpio infrastructure
from the board code using the 'setup()' and 'teardown()'
routines.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the Sharp LCD035Q3DG01 graphical LCD. This
requires a minor interface change to da8xx_register_lcdc()
so that the board code can pass in the platform_data which
describes the lcd controller that's to be used.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add pinmux settings, etc. to enable the MMC/SC hardware.
Signed-off-by: David A. Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM6467 silicon revisions 3.x have variant field in JTAGID register as '1'.
This path adds entry for the same in dm646x_ids to be able to boot on boards
with 3.x revision chips.
Also modifies name for 'variant=0' (revisions 1.0, 1.1).
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch allows Async3 clock source to be selected between PLL1 SYSCLK2
and PLL0 SYSCLK2.
Having Async3 source from PLL1 SYSCLK2 allows peripherals on that
domain to remain unaffected by frequency scaling on PLL0.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The clk_set_parent() API is implemented to enable re-parenting
clocks in the clock tree.
This is useful in DVFS and helps by shifting clocks to an asynchronous
domain where supported by hardware
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
clk_round_rate, clk_set_rate have been updated to handle dynamic
frequency changes.
The motivation behind the changes is to support dynamic CPU frequency
change.
davinci_set_pllrate() changes the PLL rate of a given PLL. This function
has been presented as a generic function though it has been tested only
on OMAP-L138 EVM. No other currently available DaVinci device will probably
use this function, but any future device specific changes will hopefully be
small enough to get taken care using a cpu_is_xxx() macro.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Make clock rate recalculation easy by having a re-calculate
function for each clock.
The existing functions for calculation of output rates of PLL
and PLL-derived sysclks have been convered to the new
re-calculate API.
A new function is introduced to take care of rate
(re)calculation for leaf clocks.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Achieve easy top down traversal of clock tree by keeping
track of each clock's list of children.
This is useful in supporting DVFS where clock rates of
all children need to be updated in an efficient manner.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This makes it clear that JTAG ID register is part of the
SYSCFG module
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Avoid use of IO_ADDRESS() for SYSCFG module by doing an ioremap() instead.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename the DA8XX_BOOT_CFG_BASE macro to get it in line
with the public documentation for these parts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The DA830/OMAP-L137 EVM cannot use the default pinmux setup for McASP1
so put the correct settings in the board file for that platform.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For consistency with existing code, change the name of
da8xx_init_mcasp() to da8xx_register_mcasp().
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some mcasp code was inserted between the emac resource setup
and the related register routine that registers the emac.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
1) Registers the platform device for McBSP on dm365.
2) Add platform data to DM365 EVM board file.
3) Set i2c address for audio codec at DM365 EVM board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The parent clock for the USB source clock is actually PLL1 aux clock,
not PLL2 sysclk1.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes a typo/bug in the DM365 SDIO interrupt assignment
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix underruns by using dma to copy 1st to sram
in a ping/pong buffer style and then copying from
the sram to the ASP. This also has the advantage
of tolerating very long interrupt latency on dma
completion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the left and right 16 bit samples to be shifted out as 1
32 bit sample.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver enables keypad support on DaVinci platforms. DM365 is the
only platform that uses this driver at the moment.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm365-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VPIF display changes (Chaithrika)
Add platform device and resource structures. Also define a platform specific
clock setup function that can be accessed by the driver to configure the clock
and CPLD.
VPIF caputure changes (Murali)
1) Modify vpif_subdev_info to add board_info, routing information and
vpif interface configuration. Remove addr since it is part of
board_info
2) Add code to setup channel mode and input decoder path for vpif
capture driver
Also incorporated comments against version v0 of the patch series and
added a spinlock to protect writes to common registers
Tested on DM6467 on channel 0 using TVP514x. Following bootargs used
for drivers:
vpif_capture.ch0_bufsize=829440 vpif_display.ch2_bufsize=829440
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM355 platform and board setup
This has platform and board setup changes to support vpfe capture
driver for DM355 EVMs.
Tested video capture on DM355 using tvp514x
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM644x platform and board setup
This adds platform and board setup changes required to support
vpfe capture driver on DM644x
Tested video capture on DM6446 with tvp514x driver
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested on DM6446, DM355, DM6447, DA850 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For best performance, codecs often setup linked triggered
transfers with a contiguous block of params, and that is when
this API is used. Setup/configuration of these parameter RAMs
is most efficient if they are contiguous.
There is an API to allocate a set of contiguous parameter RAMs and
a corresponding API to free a set of contiguous parameter RAMs
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds definitions for some DM365 IRQs that are used by
the codecs. Codecs will also use the IRQs.
Entries are being added to enable/disable IRQ's.
There is no use as such for these entires in the kernel itself.
Instead these will be used by the "linuxutils" package of the DVSDK.
For further information on IRQ muxing refer to
http://focus.ti.com/lit/ug/sprufg5a/sprufg5a.pdf
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds PINMUX entries for DM355 Display.
These will be used by the DM355 display driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On DA850/OMAP-L138 EVM, MMC/SD and NOR Flash share
some of the AEMIF pins. This patch prints out a warning
during booting, if both MMC/SD and NOR Flash are enabled
in kernel menuconfig.
If both MMC/SD and NOR Flash are enabled, only MMC/SD
will work correctly.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 8MB NOR flash
found on da850/omap-l138 EVM. Both NOR and NAND can
co-exist on da850/omap-l138 as they are using different
chip selects.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are two instances of MMC/SD on da850/omap-l138.
Connector for the first instance is available on the
EVM. This patch adds support for this instance.
This patch also adds support for card detect and write
protect switches on da850/omap-l138 EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform support for the graphic display
(Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a macro to convert the GPIO signal passed as bank number
and signal to GPIO pin number.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Define resources for McASP used on DA850/OMAP-L138 EVM, add platform
device defintion and Pin Mux configurations.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Define resources for McASP1 used on DA830/OMAP-L137 EVM, add platform
device defintion, initialization function. Additionally, this patch
also adds version and FIFO related members to platform data structure.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 has 144 pins configurable as GPIO, but
currently this has been configured as 128. This patch
corrects it.
Also, this patch adds the base address for GPIO pins
greater than 128.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Earlier patch which adds EMAC support for da850/omap-l138
was not configuring the MDIO pins.
Ethernet was working fine with the earlier patch, because
the MDIO pins were configured from the boot loader. This
patch removes that dependency.
Also, this patch populates a member in the emac clk structure
to say that EMAC LPSC sits on controller 1.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM365 RBL has been updated. The variant number has changed for this
new revision of silicon. This patch adds support for the
new revision of DM365.
The name fields are also being updated to reflect the version
of the silicon.
Without this minor fix DM365 REV 1.2 will not boot up
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The mask can hold only 8 bit values. This gave a
compilation warning. This patch rectifies the warning.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
EDMA queues in DM365 are a little different than those
on other DaVinci's. On DM365 Q0 and Q1 have the larger
FIFO size. We want Q0 and Q1 to be used by codecs and
DVSDK demos.
MMC driver is the only driver which uses the flag
'EVENTQ_DEFAULT'. So MMC driver should be using Q2 instead of
Q1 on DM365.
This patch allows us to declare a "default queue" from
SOC specific code. If it is not declared then the EDMA
driver assumes a default of queue 1.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM365 and DM6467 have 4 queues. The patch updates the
'dma_event_q' enum to reflect this.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There is no need to pass clock name strings in platform_data.
Instead, setup clkdev nodes to have correct ASoC device names.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Controls ATA_RSTn and ATA_PWD through CPLD register 0 to enable ATA. An I2C
driver is added for the same. Calls ide init if enabled in configuration.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ethernet Media Access Controller (EMAC) on da850/omap-l138
supports 10/100 Mbps operation. It also supports Media
Independent Interface (MII) and Reduced Media Independent
Interface (RMII) to physical layer (PHY).
Phy which supports MII is present on the DA850/OMAP-L138
base board and Phy supporting RMII is present on the
UI card. This patch adds support only for the MII Phy.
Support for RMII Phy will be added later.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the DA850/OMAP-L138 Evaluation Module (EVM)
from TI. The EVM has User Interface (UI) card which contains
various devices. This UI card can be connected to the base
board. Support for all the devices on the UI card and ones on
the EVM will be added in subsequent patches.
The EVM schematics are not available publicly yet; but should
be available soon.
A new defconfig for this board has been added mainly because
the DA830/OMAP-L137 defconfig forces writethrough cache mode
which is not required on DA850/OMAP-L138.
This patch has been boot tested on DA850/OMAP-L138 EVM
using ramdisk as filesystem.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The DA850/OMAP-L138 is a new SoC from TI in the same family as
DA830/OMAP-L137.
Major changes include better support for power management,
support for SATA devices and McBSP (same IP as DM644x).
DA850/OMAP-L138 documents are available at
http://focus.ti.com/docs/prod/folders/print/omap-l138.html.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM646x has MUSB connected to IRQs 13 and 14 (unlike IRQ12 on other platforms),
so pass the correct IRQ resources with the platform device.
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rearrange the PINMUX macros and pinmux_setup function which
are common between da830/omap-l137 and da850/omap-l138.
Also, replace the da830 string in function names to da8xx.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
With the introduction of TI da850/omap-l138, some of the macros
defined for da830/omap-l137 will be needed in da850 source file.
So, move the common macros to da8xx.h header file.
Also, modify the macro names from DA830_... to DA8XX_.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data and init function for IDE which could be called
from board specific file to register IDE device.
Note that for 594MHz device the transfer mode is limited to UDMA4 since ideclk
rate is less than 100 MHz, which forces udma_mask in palm_bk3710.c to UDMA4,
while for 729MHz device, it is UDMA5.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Make arch_idle and arch_reset inline as inline function.
Not having them inline leads to a warning of this sort when only
one of these functions is used:
arch/arm/mach-davinci/include/mach/system.h:24: warning: 'arch_reset' \
defined but not used
boot, re-boot tested on OMAP-L138 EVM
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch takes out IO mapping macros from mach/io.h and puts them in
mach/hardware.h avoiding need to include mach/io.h in various files such as
serial.h, vmalloc.h etc.
The main reason to avoid inclusion of mach/io.h is, when default in/out macros
are overridden by machine specific functions (e.g., in case of PCI I/O), they
result into linker error. An example snippet and error snapshot is listed below.
Following code in mach/io.h:
#define inl(p) my_inl()
static inline unsigned int my_inl(unsigned int addr)
{
if (IS_PCI_IO(addr))
return pci_inl ();
else
return le32_to_cpu(__raw_readl(__typesafe_io(addr)));
}
leads to error:
LD arch/arm/boot/compressed/vmlinux
arch/arm/boot/compressed/misc.o: In function `my_inl':
misc.c:(.text+0x2744): undefined reference to `pci_inl'
make[2]: *** [arch/arm/boot/compressed/vmlinux] Error 1
This is because mach/io.h gets included in arch/arm/boot/compressed/misc.c
through mach/serial.h but pci.c file, which defines 'pci_inl' doesn't get built
into compressed vmlinux.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds clock data for IDE and also updates pin mux mask for ATA so as
to disable PCI when ATA is selected.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
1) Registers the platform devices for ASP on dm355, dm644x and dm646x
so that the machine driver can probe to get ASP related platform
data.
2) Move towards definition of the asp clocks using physical name(for
dm355 and dm644x)
3) Add platform data to board specific files.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Support DM365 GPIOs ... primarily by handling non-banked GPIO IRQs:
- Flag DM365 chips as using non-banked GPIO interrupts, using a
new soc_info field.
- Replace the gpio_to_irq() mapping logic. This now uses some
runtime infrastructure, keyed off that new soc_info field,
which doesn't handle irq_to_gpio().
- Provide a new irq_chip ... GPIO IRQs handled directly by AINTC
still need edge triggering managed by the GPIO controller.
DM365 chips no longer falsely report 104 GPIO IRQs as they boot.
Intelligence about IRQ muxing is missing, so for the moment this
only exposes the first eight DM365 GPIOs, which are never muxed.
The next eight are muxed, half with Ethernet (which uses most of
those pins anyway).
Tested on DM355 (10 unbanked IRQs _or_ 104 banked ones) and also
on DM365 (16 unbanked ones, only 8 made available).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the DA830/OMAP-L137 Evaluation Module (EVM)
from TI. The EVM has User Interface (UI) and Audio cards
that can be connected which contain various devices.
Support for those devices and ones on the EVM will be
added in subsequent patches.
Additional generalizations for future SoCs in da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The da830/omap l137 is a new SoC from TI that is similar
to the davinci line. Since its so similar to davinci,
put the support for the da830 in the same directory as
the davinci code.
There are differences, however. Some of those differences
prevent support for davinci and da830 platforms to work
in the same kernel binary. Those differences are:
1) Different physical address for RAM. This is relevant
to Makefile.boot addresses and PHYS_OFFSET. The
Makefile.boot issue isn't truly a kernel issue but
it means u-boot won't work with a uImage including
both architectures. The PHYS_OFFSET issue is
addressed by the "Allow for runtime-determined
PHYS_OFFSET" patch by Lennert Buytenhek but it
hasn't been accepted yet.
2) Different uart addresses. This is only an issue
for the 'addruart' assembly macro when CONFIG_DEBUG_LL
is enabled. Since the code in that macro is called
so early (e.g., by _error_p in kernel/head.S when
the processor lookup fails), we can't determine what
platform the kernel is running on at runtime to use
the correct uart address.
These areas have compile errors intentionally inserted
to indicate to the builder they're doing something wrong.
A new config variable, CONFIG_ARCH_DAVINCI_DMx, is added
to distinguish between a true davinci architecture and
the da830 architecture.
Note that the da830 currently has an issue with writeback
data cache so CONFIG_CPU_DCACHE_WRITETHROUGH should be
enabled when building a da830 kernel.
Additional generalizations for future SoCs in the da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add basic support for the CPLD on the DM365 EVM board:
- Read SW5 to set up NAND and keypad vs (someday) OneNAND
- Export MMC/SD card detect and writeprotect signals
- LED support (same layout as on DM355 EVM)
- Static config for video input:
* external HD imager precludes MMC1, Ethernet, audio
* else either tvp5146 (SD/default) or tvp7002 (HD)
The video input could actually be switched around dynamically;
change that if/when that's needed (and after those other video
inputs have driver support).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Patch adds support for MMC/SD in the DM365 EVM.
Pinmux for MMC/SD slot 1 on the DM365 EVM is also
configured.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds Support for EMAC in the DM365 SOC and
the DM365 EVM board.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch does the following
1) Adds entries to davinci_all_defconfig for DM365
2) Adds entries to the Makefile for DM365
3) Adds entries for DM365 in the Kconfig
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds support for Evaluation Module (EVM) board for the dm365
SoC.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds base support for new TI SOC DM365, which s
similar to the dm355.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
CC arch/arm/mach-davinci/sram.o
arch/arm/mach-davinci/sram.c: In function 'sram_init':
arch/arm/mach-davinci/sram.c:63: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
JTAG ID for DM644x silicon revision 2.1 has changed. An entry for the new
silicon revision needs to be added to the davinci_id structure. Without
this addition, EVMs with new silicon revision fail to boot the kernel.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The davinci reset routine, davinci_watchdog_reset(), sets the
TCR register instead of the TGCR register as it should to put
the WDT into its "Initial State".
It also writes the WDTCR register without the proper WDKEY
which is pointless since the register will be write-protected.
Signed-off-by: David Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds McASP clock support for the two instances of mcasp (mcasp0,mcasp1). This
patch is part of the audio support for dm646x series.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
- restructure to support multiple channel controllers by using
additional struct resources for each CC
- interface changes visible to EDMA clients
Introduce macros to build IDs from controller and channel number,
and to extract them. Modify the edma_alloc_slot function to take an
extra argument for the controller.
Also update ASoC drivers to use API. ASoC changes
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- Move queue related mappings to dm<soc>.c
EDMA in DM355 and DM644x has two transfer controllers while DM646x
has four transfer controllers. Moving the queue to tc mapping and
queue priority mapping to dm<soc>.c will be helpful to probe these
mappings from platform device so that the machine_is_* testing will
be avoided.
- add channel mapping logic
Channel mapping logic is introduced in dm646x EDMA. This implies
that there is no fixed association for a channel number to a
parameter entry number. In other words, using the DMA channel
mapping registers (DCHMAPn), a PaRAM entry can be mapped to any
channel. While in the case of dm644x and dm355 there is a fixed
mapping between the EDMA channel and Param entry number.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
Minimal support for the 4-bit ECC engine found on DM355, DM365,
DA830/OMAP-L137, and similar recent DaVinci-family chips.
This is limited to small-page flash for now; there are some page
layout issues for large page chips. Note that most boards using
this engine (like the DM355 EVM) include 2GiB large page chips.
Sanity tested on DM355 EVM after swapping the socketed NAND for
a small-page one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some DMA_32BIT_MASK usage snuck in with the MMC platform support.
Convert these to the new preferred DMA_BIT_MASK(32).
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a generic SRAM allocator using genalloc, and vaguely
modeled after what AVR32 uses. This builds on top of the
static CPU mapping set up in the previous patch, and returns
DMA mappings as requested (if possible).
Compared to its OMAP cousin, there's no current support for
(currently non-existent) DaVinci power management code running
in SRAM; and this has ways to deallocate, instead of being
allocate-only.
The initial user of this should probably be the audio code,
because EDMA from DDR is subject to various dropouts on at
least DM355 and DM6446 chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Package on-chip SRAM. It's always accessible from the ARM, so
set up a standardized virtual address mapping into a 128 KiB
area that's reserved for platform use.
In some cases (dm6467) the physical addresses used for EDMA are
not the same as the ones used by the ARM ... so record that info
separately in the SOC data, for chips (unlike the OMAP-L137)
where SRAM may be used with EDMA.
Other blocks of SRAM, such as the ETB buffer or DSP L1/L2 RAM,
may be unused/available on some system. They are ignored here.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove remnants of dm6446-specific SRAM allocator, as preparation for
a more generic replacement.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Different SoC have different numbers of pinmux registers and other
resources that overlap with each other. To clean up the code and
eliminate defines that overlap with each other, move the PINMUX
defines to the SoC specific files.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The Timer64p timer has 8 compare registers that can
be used to generate interrupts when the timer value
matches the compare reg's value. They do not disturb
the timer itself. This can be useful when there is
only one timer available for both clock events and
clocksource.
When enabled, the clocksource remains a continuous
32-bit counter but the clock event will no longer
support periodic interrupts. Instead only oneshot
timers will be supported and implemented by setting
the compare register to the current timer value plus
the period that the clock event subsystem is requesting.
Compare registers support is enabled automatically
when the following conditions are met:
1) The same timer is being used for clock events
and clocksource.
2) The timer is the bottom half (32 bits) of the
64-bit timer (hardware limitation).
3) The the compare register offset and irq are
not zero.
Since the timer is always running, there is a hardware
race in timer32_config() between reading the current
timer value, and adding the period to the current
timer value and writing the compare register.
Testing on a da830 evm board with the timer clocked
at 24 MHz and the processor clocked at 300 MHz,
showed the number of counter ticks to do this ranged
from 20-53 (~1-2.2 usecs) but usually around 41 ticks.
This includes some artifacts from collecting the
information. So, the minimum period should be
at least 5 usecs to be safe.
There is also an non-critical lower limit that
the period should be since there is no point in
setting an event that is much shorter than the
time it takes to set the event, and get & handle
the timer interrupt for that event. There can
also be all sorts of delays from activities
occuring elsewhere in the system (including
hardware activitis like cache & TLB management).
These are virtually impossible to quantify so a
minimum period of 50 usecs was chosen. That will
certianly be enough to avoid the actual hardware
race but hopefully not large enough to cause
unreasonably course-grained timers.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Integrate the Common Platform Interrupt Controller (cp_intc)
support into the low-level irq handling for davinci and similar
platforms. Do it such that support for cp_intc and the original
aintc can coexist in the same kernel binary.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Factor out the code to extract that mac address from
i2c eeprom.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The dm644x and dm646x board files have i2c eeprom read and
write routines but they are not used so remove them.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since most of the emac platform_data is really SoC specific
and not board specific, move it to the SoC-specific files.
Put a pointer to the platform_data in the soc_info structure
so the board-specific code can set some of the platform_data
if it needs to.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, there is one set of platform_device and platform_data
structures for all DaVinci SoCs. The differences in the data
between the various SoCs is handled by davinci_serial_init()
by checking the SoC type. However, as new SoCs appear, this
routine will become more & more cluttered.
To clean up the routine and make it easier to add support for new
SoCs, move the platform_device and platform_data structures into the
SoC-specific code and use the SoC infrastructure to provide access
to the data.
In the process, fix a bug where the wrong irq is used for uart2
of the dm646x.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
