I have what looks like a Geovision GV-600 (or 650) card. It has a large
chip in the middle labeled
CONEXANT
FUSION 878A
25878-13
E345881.1
0312 TAIWAN
It has an audio connector coming out from a chip labeled
ATMEL
0242
AT89C2051-24PI
It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18)
...
01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
...
01:0a.0 0400: 109e:036e (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dfffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
01:0a.1 0480: 109e:0878 (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dffff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18
kernel and the latest v4l-dvb drivers, but it did not work at all. The
card has sixteen (16) BNC video inputs, four of them on the board itself
and twelve on three daughter-cards. It has a single bt878 chip, no tuner
and what looks like and audio input. After doing some research I managed
to get only eight channels working by forcing card=125 and those DID NOT
match channels 0-7 on the card, and no audio.
Based on what was working for card=125, I added the card definition
block, added a specific muxsel routine and got the card working fully
with xawtv, where the sixteen channels show up as Composite0 to
Composite15, matching the channel labels in the card and daughter-cards.
I have made no efforts yet to get audio working, but would appreciate
any pointers.
Signed-off-by: Ernesto Hernández-Novich <emhn@usb.ve>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix GPIO for FusionHDTV 7 Gold tv / s-video / composite input selection.
Fix card textual name to match other FusionHDTV device names.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the following saa7134 xc3028 based boards:
132 -> AVerMedia Cardbus TV/Radio (E506R) [1461:f436]
133 -> AVerMedia Hybrid TV/Radio (A16D) [1461:f936]
134 -> Avermedia M115 [1461:a836]
135 -> Compro VideoMate T750 [185b:c900]
This is based on a original patch thanks to Markus Rechberger that added xc3028
gpio init code for the above boards.
This patch moves saa7134_tuner_callback to saa7134-cards, originally used only
by tda8290 DVB-S boards. The callback was made more generic to support other
tuners.
Currently, it supports both tda8290 and xc2028/xc3028 tuners. Added also the
basis for xc5000 tuner callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for tuning DVB-T channels on DViCO's FusionHDTV DVB-T Pro board.
The IR remote and analog tuner are not supported at this time.
Some changes made by Mauro Chehab to allow merging it with some other xc3028
patches.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch ports a patch from Markus Rechberger to work with tuner-xc2028.
It adds entries for several cx88 boards with xc2038/3028 tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
load ir-kbd-i2c for IR remote control support on DViCO FusionHDTV 5 PCI nano
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATSC is known to work.
SVideo / Composite should work (I have no cable to test).
Analog tuner support does not work.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added the support of AD1989A and AD1989B codecs.
These codecs can have multiple SPDIF devices, but currently we handle
only one SPDIF. If any real devices with two SPDIF interfaces (likely
one for SPDIF and one for HDMI), we'll fix this rightly.
Otherwise, these codecs are pretty similar with AD1988.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds support for Quanta IL1 mini-notebook to alsa, defining a new model
for it. It comes with an ALC267 codec chip. Some notes about this model:
* In headphone automute, I use AC_VERB_SET_PIN_WIDGET_CONTROL instead of common
amp mute, to avoid conflict with mixer switch (mixer and automute use the
same nid).
* The only connected capture sources in the hardware are the internal mic and
external mic jack. So instead of using an input source selector like on other
ALC268 models, the mic automute automatically switch between captures.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for mic automute in clevo-m720r ALC883 model, and rename it
to more generic clevo-m720. Also change model entry in ALSA-Configuration.txt
accordingly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After DAC assignment fix in ALC883, the 6stack-hp model is now the same
as 6stack-dig. So just remove 6stack-hp model and replace its use with
6stack-dig.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of new AD codecs: AD1883, AD1884A, AD1984A and AD1984B.
These are almost compatible except for additional digital pins, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some instructions for using the new NFS/RDMA features.
Signed-off-by: James Lentini <jlentini@netapp.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Show peer group ID of nearest dominating group that has intersection
with the mount's namespace.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mszeredi@suse.cz] rewrite and split big patch into managable chunks
/proc/mounts in its current form lacks important information:
- propagation state
- root of mount for bind mounts
- the st_dev value used within the filesystem
- identifier for each mount and it's parent
It also suffers from the following problems:
- not easily extendable
- ambiguity of mountpoints within a chrooted environment
- doesn't distinguish between filesystem dependent and independent options
- doesn't distinguish between per mount and per super block options
This patch introduces /proc/<pid>/mountinfo which attempts to address
all these deficiencies.
Code shared between /proc/<pid>/mounts and /proc/<pid>/mountinfo is
extracted into separate functions.
Thanks to Al Viro for the help in getting the design right.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This adds support for using large page NAND devices
with the S3C24XX NAND controller. This also adds the
file Documentation/arm/Samsung-S3C24XX/NAND.txt to
describe the differences.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial: (24 commits)
DOC: A couple corrections and clarifications in USB doc.
Generate a slightly more informative error msg for bad HZ
fix typo "is" -> "if" in Makefile
ext*: spelling fix prefered -> preferred
DOCUMENTATION: Use newer DEFINE_SPINLOCK macro in docs.
KEYS: Fix the comment to match the file name in rxrpc-type.h.
RAID: remove trailing space from printk line
DMA engine: typo fixes
Remove unused MAX_NODES_SHIFT
MAINTAINERS: Clarify access to OCFS2 development mailing list.
V4L: Storage class should be before const qualifier (sn9c102)
V4L: Storage class should be before const qualifier
sonypi: Storage class should be before const qualifier
intel_menlow: Storage class should be before const qualifier
DVB: Storage class should be before const qualifier
arm: Storage class should be before const qualifier
ALSA: Storage class should be before const qualifier
acpi: Storage class should be before const qualifier
firmware_sample_driver.c: fix coding style
MAINTAINERS: Add ati_remote2 driver
...
Fixed up trivial conflicts in firmware_sample_driver.c
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
block: fix blk_register_queue() return value
block: fix memory hotplug and bouncing in block layer
block: replace remaining __FUNCTION__ occurrences
Kconfig: clean up block/Kconfig help descriptions
cciss: fix warning oops on rmmod of driver
cciss: Fix race between disk-adding code and interrupt handler
block: move the padding adjustment to blk_rq_map_sg
block: add bio_copy_user_iov support to blk_rq_map_user_iov
block: convert bio_copy_user to bio_copy_user_iov
loop: manage partitions in disk image
cdrom: use kmalloced buffers instead of buffers on stack
cdrom: make unregister_cdrom() return void
cdrom: use list_head for cdrom_device_info list
cdrom: protect cdrom_device_info list by mutex
cdrom: cleanup hardcoded error-code
cdrom: remove ifdef CONFIG_SYSCTL
A couple of corrections and clarifications in USB
documentation.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
Remove BitKeeper from dontdiff. Point to the klibc git repository
instead of old BitKeeper ones.
Signed-off-by: Cyril Brulebois <cyril.brulebois@kerlabs.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Now unregister_cdrom() always returns 0.
Make it return void and update all callers that check the return value.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Vital Product Data (VPD) may be exposed by PCI devices in several
ways. It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.
This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
(in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
operations defined
It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for batching up the flushing of the IOTLB for the DMAR
implementation found in the Intel VT-d hardware. It works by building a list
of to be flushed IOTLB entries and a bitmap list of which DMAR engine they are
from.
After either a high water mark (250 accessible via debugfs) or 10ms the list
of iova's will be reclaimed and the DMAR engines associated are IOTLB-flushed.
This approach recovers 15 to 20% of the performance lost when using the IOMMU
for my netperf udp stream benchmark with small packets. It can be disabled
with a kernel boot parameter "intel_iommu=strict".
Its use does weaken the IOMMU protections a bit.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently keep 2 lists of PCI devices in the system, one in the
driver core, and one all on its own. This second list is sorted at boot
time, in "BIOS" order, to try to remain compatible with older kernels
(2.2 and earlier days). There was also a "nosort" option to turn this
sorting off, to remain compatible with even older kernel versions, but
that just ends up being what we have been doing from 2.5 days...
Unfortunately, the second list of devices is not really ever used to
determine the probing order of PCI devices or drivers[1]. That is done
using the driver core list instead. This change happened back in the
early 2.5 days.
Relying on BIOS ording for the binding of drivers to specific device
names is problematic for many reasons, and userspace tools like udev
exist to properly name devices in a persistant manner if that is needed,
no reliance on the BIOS is needed.
Matt Domsch and others at Dell noticed this back in 2006, and added a
boot option to sort the PCI device lists (both of them) in a
breadth-first manner to help remain compatible with the 2.4 order, if
needed for any reason. This option is not going away, as some systems
rely on them.
This patch removes the sorting of the internal PCI device list in "BIOS"
mode, as it's not needed at all anymore, and hasn't for many years.
I've also removed the PCI flags for this from some other arches that for
some reason defined them, but never used them.
This should not change the ordering of any drivers or device probing.
[1] The old-style pci_get_device and pci_find_device() still used this
sorting order, but there are very few drivers that use these functions,
as they are deprecated for use in this manner. If for some reason, a
driver rely on the order and uses these functions, the breadth-first
boot option will resolve any problem.
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Create Documentation/PCI/ and move PCI-related files to it.
Fix a few instances of trailing whitespace.
Update references to the new file locations.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Requiring userspace to close and re-open sysfs attributes has been the
policy since before 2.6.12. It allows userspace to get a consistent
snapshot of kernel state and consume it with incremental reads and seeks.
Now, if the file position is zero the kernel assumes userspace wants to see
the new value. The application for this change is to allow a userspace
RAID metadata handler to check the state of an array without causing any
memory allocations. Thus not causing writeback to a raid array that might
be blocked waiting for userspace to take action.
Cc: Neil Brown <neilb@suse.de>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add /sysfs/firmware/ibft/[initiator|targetX|ethernetX] directories along with
text properties which export the the iSCSI Boot Firmware Table (iBFT)
structure.
What is iSCSI Boot Firmware Table? It is a mechanism for the iSCSI tools to
extract from the machine NICs the iSCSI connection information so that they
can automagically mount the iSCSI share/target. Currently the iSCSI
information is hard-coded in the initrd. The /sysfs entries are read-only
one-name-and-value fields.
The usual set of data exposed is:
# for a in `find /sys/firmware/ibft/ -type f -print`; do echo -n "$a: "; cat $a; done
/sys/firmware/ibft/target0/target-name: iqn.2007.com.intel-sbx44:storage-10gb
/sys/firmware/ibft/target0/nic-assoc: 0
/sys/firmware/ibft/target0/chap-type: 0
/sys/firmware/ibft/target0/lun: 00000000
/sys/firmware/ibft/target0/port: 3260
/sys/firmware/ibft/target0/ip-addr: 192.168.79.116
/sys/firmware/ibft/target0/flags: 3
/sys/firmware/ibft/target0/index: 0
/sys/firmware/ibft/ethernet0/mac: 00:11:25:9d:8b:01
/sys/firmware/ibft/ethernet0/vlan: 0
/sys/firmware/ibft/ethernet0/gateway: 192.168.79.254
/sys/firmware/ibft/ethernet0/origin: 0
/sys/firmware/ibft/ethernet0/subnet-mask: 255.255.252.0
/sys/firmware/ibft/ethernet0/ip-addr: 192.168.77.41
/sys/firmware/ibft/ethernet0/flags: 7
/sys/firmware/ibft/ethernet0/index: 0
/sys/firmware/ibft/initiator/initiator-name: iqn.2007-07.com:konrad.initiator
/sys/firmware/ibft/initiator/flags: 3
/sys/firmware/ibft/initiator/index: 0
For full details of the IBFT structure please take a look at:
ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ibm_iscsi_boot_firmware_table_v1.02.pdf
[akpm@linux-foundation.org: fix build]
Signed-off-by: Konrad Rzeszutek <konradr@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Source file was removed. Need to remove docbook reference also.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavel Machek <pavel@suse.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the PM core to protect its data structures, specifically the
dpm_active list, from being corrupted if a child of the currently
suspending device is registered concurrently with its ->suspend()
callback. In that case, since the new device (the child) is added
to dpm_active after its parent, the PM core will attempt to
suspend it after the parent, which is wrong.
Introduce a new member of struct dev_pm_info, called 'sleeping',
and use it to check if the parent of the device being added to
dpm_active has been suspended, in which case the device registration
fails. Also, use 'sleeping' for checking if the ordering of devices
on dpm_active is correct.
Introduce variable 'all_sleeping' that will be set to 'true' once all
devices have been suspended and make new device registrations fail
until 'all_sleeping' is reset to 'false', in order to avoid having
unsuspended devices around while the system is going into a sleep state.
Remove pm_sleep_rwsem which is not necessary any more.
Special thanks to Alan Stern for discussions and suggestions that
lead to the creation of this patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the firmware_class sample drivers to samples/ so that they are
buildable and can be maintained.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Viktor was nice enough to enhance the document based on my replies to
his questions on the subject.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch introduces new feature of cpuset - sched domain customization.
This version provides a per-cpuset file 'sched_relax_domain_level' that
enable us to change the searching range of scheduler, which used to limit
how many cpus the scheduler searches at some schedule events, such as
wakening task and running out of runqueue.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we merge the iommu initialization parameters in pci-dma.c
Nice thing, that both architectures at least recognize the same
parameters.
usedac i386 parameter is marked for deprecation
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds three tests that test whether the PR_GET_TSC and
PR_SET_TSC commands have the desirable effect.
The tests check whether the control register is updated correctly
at context switches and try to discover bugs while enabling/disabling
the timestamp counter.
Signed-off-by: Erik Bosman <ejbosman@cs.vu.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- noexec32 is on by default for years already
- add noexec32 to kernel-parameters and fix noexec typo in there
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
security: fix up documentation for security_module_enable
Security: Introduce security= boot parameter
Audit: Final renamings and cleanup
SELinux: use new audit hooks, remove redundant exports
Audit: internally use the new LSM audit hooks
LSM/Audit: Introduce generic Audit LSM hooks
SELinux: remove redundant exports
Netlink: Use generic LSM hook
Audit: use new LSM hooks instead of SELinux exports
SELinux: setup new inode/ipc getsecid hooks
LSM: Introduce inode_getsecid and ipc_getsecid hooks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.26: (1090 commits)
[NET]: Fix and allocate less memory for ->priv'less netdevices
[IPV6]: Fix dangling references on error in fib6_add().
[NETLABEL]: Fix NULL deref in netlbl_unlabel_staticlist_gen() if ifindex not found
[PKT_SCHED]: Fix datalen check in tcf_simp_init().
[INET]: Uninline the __inet_inherit_port call.
[INET]: Drop the inet_inherit_port() call.
SCTP: Initialize partial_bytes_acked to 0, when all of the data is acked.
[netdrvr] forcedeth: internal simplifications; changelog removal
phylib: factor out get_phy_id from within get_phy_device
PHY: add BCM5464 support to broadcom PHY driver
cxgb3: Fix __must_check warning with dev_dbg.
tc35815: Statistics cleanup
natsemi: fix MMIO for PPC 44x platforms
[TIPC]: Cleanup of TIPC reference table code
[TIPC]: Optimized initialization of TIPC reference table
[TIPC]: Remove inlining of reference table locking routines
e1000: convert uint16_t style integers to u16
ixgb: convert uint16_t style integers to u16
sb1000.c: make const arrays static
sb1000.c: stop inlining largish static functions
...
Add the security= boot parameter. This is done to avoid LSM
registration clashes in case of more than one bult-in module.
User can choose a security module to enable at boot. If no
security= boot parameter is specified, only the first LSM
asking for registration will be loaded. An invalid security
module name will be treated as if no module has been chosen.
LSM modules must check now if they are allowed to register
by calling security_module_enable(ops) first. Modify SELinux
and SMACK to do so.
Do not let SMACK register smackfs if it was not chosen on
boot. Smackfs assumes that smack hooks are registered and
the initial task security setup (swapper->security) is done.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
[SCSI] iscsi: bidi support for iscsi_tcp
[SCSI] iscsi: bidi support at the generic libiscsi level
[SCSI] iscsi: extended cdb support
[SCSI] zfcp: Fix error handling for blocked unit for send FCP command
[SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
[SCSI] zfcp: fix 31 bit compile warnings
[SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
[SCSI] bsg: remove minor in struct bsg_device
[SCSI] bsg: use better helper list functions
[SCSI] bsg: replace kobject_get with blk_get_queue
[SCSI] bsg: takes a ref to struct device in fops->open
[SCSI] qla1280: remove version check
[SCSI] libsas: fix endianness bug in sas_ata
[SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
[SCSI] aacraid: Do not describe check_reset parameter with its value
[SCSI] aacraid: Fix down_interruptible() to check the return value
[SCSI] sun3_scsi_vme: add MODULE_LICENSE
[SCSI] st: rename flush_write_buffer()
[SCSI] tgt: use KMEM_CACHE macro
[SCSI] initio: fix big endian problems for auto request sense
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (43 commits)
firewire: cleanups
firewire: fix synchronization of gap counts
firewire: wait until PHY configuration packet was transmitted (fix bus reset loop)
firewire: remove unused struct member
firewire: use bitwise and to get reg in handle_registers
firewire: replace more hex values with defined csr constants
firewire: reread config ROM when device reset the bus
firewire: replace static ROM cache by allocated cache
firewire: fw-ohci: work around generation bug in TI controllers (fix AV/C and more)
firewire: fw-ohci: extend logging of bus generations and node ID
firewire: fw-ohci: conditionally log busReset interrupts
firewire: fw-ohci: don't append to AT context when it's not active
firewire: fw-ohci: log regAccessFail events
firewire: fw-ohci: make sure HCControl register LPS bit is set
firewire: fw-ohci: missing PPC PMac feature calls in failure path
firewire: fw-ohci: untangle a mixed unsigned/signed expression
firewire: debug interrupt events
firewire: fw-ohci: catch self_id_count == 0
firewire: fw-ohci: add self ID error check
firewire: fw-ohci: refactor probe, remove, suspend, resume
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (64 commits)
ocfs2/net: Add debug interface to o2net
ocfs2: Only build ocfs2/dlm with the o2cb stack module
ocfs2/cluster: Get rid of arguments to the timeout routines
ocfs2: Put tree in MAINTAINERS
ocfs2: Use BUG_ON
ocfs2: Convert ocfs2 over to unlocked_ioctl
ocfs2: Improve rename locking
fs/ocfs2/aops.c: test for IS_ERR rather than 0
ocfs2: Add inode stealing for ocfs2_reserve_new_inode
ocfs2: Add ac_alloc_slot in ocfs2_alloc_context
ocfs2: Add a new parameter for ocfs2_reserve_suballoc_bits
ocfs2: Enable cross extent block merge.
ocfs2: Add support for cross extent block
ocfs2: Move /sys/o2cb to /sys/fs/o2cb
sysfs: Allow removal of symlinks in the sysfs root
ocfs2: Reconnect after idle time out.
ocfs2/dlm: Cleanup lockres print
ocfs2/dlm: Fix lockname in lockres print function
ocfs2/dlm: Move dlm_print_one_mle() from dlmmaster.c to dlmdebug.c
ocfs2/dlm: Dumps the purgelist into a debugfs file
...
/sys/fs is where we really want file system specific sysfs objects.
Ocfs2-tools has been updated to look in /sys/fs/o2cb. We can maintain
backwards compatibility with old ocfs2-tools by using a sysfs symlink. After
some time (2 years), the symlink can be safely removed. This patch also adds
documentation to make it easier for people to figure out what /sys/fs/o2cb
is used for.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Add ABI documentation for these files:
/sys/fs/ocfs2/max_locking_protocol
/sys/fs/ocfs2/loaded_cluster_plugins
/sys/fs/ocfs2/active_cluster_plugin
/sys/fs/ocfs2/cluster_stack
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Bernhard Kaindl <bk@suse.de>
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (87 commits)
[XFS] Fix merge failure
[XFS] The forward declarations for the xfs_ioctl() helpers and the
[XFS] Update XFS documentation for noikeep/ikeep.
[XFS] Update XFS Documentation for ikeep and ihashsize
[XFS] Remove unused HAVE_SPLICE macro.
[XFS] Remove CONFIG_XFS_SECURITY.
[XFS] xfs_bmap_compute_maxlevels should be based on di_forkoff
[XFS] Always use di_forkoff when checking for attr space.
[XFS] Ensure the inode is joined in xfs_itruncate_finish
[XFS] Remove periodic logging of in-core superblock counters.
[XFS] fix logic error in xfs_alloc_ag_vextent_near()
[XFS] Don't error out on good I/Os.
[XFS] Catch log unmount failures.
[XFS] Sanitise xfs_log_force error checking.
[XFS] Check for errors when changing buffer pointers.
[XFS] Don't allow silent errors in xfs_inactive().
[XFS] Catch errors from xfs_imap().
[XFS] xfs_bulkstat_one_dinode() never returns an error.
[XFS] xfs_iflush_fork() never returns an error.
[XFS] Catch unwritten extent conversion errors.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
clocksource: make clocksource watchdog cycle through online CPUs
Documentation: move timer related documentation to a single place
clockevents: optimise tick_nohz_stop_sched_tick() a bit
locking: remove unused double_spin_lock()
hrtimers: simplify lockdep handling
timers: simplify lockdep handling
posix-timers: fix shadowed variables
timer_list: add annotations to workqueue.c
hrtimer: use nanosleep specific restart_block fields
hrtimer: add nanosleep specific restart_block member
Mention how DMAPI affects default for noikeep.
Slightly modified since Josef's patch was based on
an old xfs.txt prior to Dave's (dgc) checkin which
missed going to oss.
Signed-off-by: Josef Sipek <jeffpc@josefsipek.net>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Update xfs docs for:
* In memory inode hashes has been removed.
* noikeep is now the default.
SGI-PV: 969561
SGI-Modid: 2.6.x-xfs-melb:linux:29481b
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tim Shimmin <tes@sgi.com>
CONFIG_BLK_DEV_4DRIVES deserves its own host driver:
* Add drivers/ide/legacy/ide-4drives.c and move "4drives" support there.
* Add ide-4drives.o in the link order after all other legacy host
drivers enabled by "ide0=" options (they all are mutually exclusive).
* Make ide-4drives host driver probe itself for IDE devices instead of
indirectly depending on ide_generic host driver.
* Add "probe" module parameter to ide-4drives and update documentation.
v2:
* s/paramater/parameter/ in ide.txt. (Noticed by Randy Dunlap)
v3:
* s/ide_4drives.probe/ide-4drives.probe/ in help entry.
(Noticed by Sergei Shtylyov)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove CONFIG_BLK_DEV_HD hack from init_hwif_default()
("hda=noprobe hdb=noprobe" kernel parameters should be used
instead if somebody wishes to use the old "hd" driver).
* Make CONFIG_BLK_DEV_HD_ONLY config option available also when
IDE subsystem is used and update help entry.
* Remove no longer needed CONFIG_BLK_DEV_HD_IDE config option.
v2:
* Update documentation to suggest "hda=noprobe hdb=noprobe"
instead of obsoleted "ide0=noprobe".
* Update Documentation/ide/ide.txt.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct class ide_port_class' ('ide_port' class) and a 'struct
device *portdev' ('ide_port' class device) in ide_hwif_t.
* Register 'ide_port' class in ide_init() and unregister it in
cleanup_module().
* Create ->portdev in ide_register_port () and unregister it in
ide_unregister().
* Add "delete_devices" class device attribute for unregistering IDE devices
on a port and "scan" one for probing+registering IDE devices on a port.
* Add ide_sysfs_register_port() helper for registering "delete_devices"
and "scan" attributes with ->portdev. Call it in ide_device_add_all().
* Document IDE warm-plug support in Documentation/ide/warm-plug-howto.txt.
v2:
* Convert patch from using 'struct class_device' to use 'struct device'.
(thanks to Kay Sievers for doing it)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This option is obsolete and can be removed safely.
It allows us to remove the pci_get_device_reverse() function from the
PCI core.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
use of the bzImage symlinks in developer scripts is still widespread,
so lets extend the removal period by 2 years. These symlinks cost
us near nothing.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix coding style in pci-dma_64.c and add stubs for documentation. I
hope someone fills the rest, I understand maybe off and soft...
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Also update field names to simply payload_{offset,length} so as to not rule
out uncompressed images.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These new controls toggle experimental support for a new CPU feature,
the straightforward extension of largepages from the pmd level to the
pud level, which allows 1GB (kernel) TLBs instead of 2MB TLBs.
Turn it off by default, as this code has not been tested well enough yet.
Use the CONFIG_DIRECT_GBPAGES=y .config option or gbpages on the
boot line can be used to enable it. If enabled in the .config then
nogbpages boot option disables it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have two directories with timer related information in
Documentation/: hrtimers/ and hrtimer/. timer_stats are not restricted
to hrtimers. Move all those files into Documentation/timers where we
can pile up other timer related docs as well.
Pointed-out-by: Randy Dunlap <randy@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- get rid of `model = "UCC"' in the ucc nodes
It isn't used anywhere, so remove it. If we'll ever need something
like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
Drivers are modified for backward compatibility's sake.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new function supports setting of permissions for the debugfs files
created by the debug feature. In addition to that, the function provides
uid and gid as parameters for future use. Currently only root is allowed
for uid and gid.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This implements support for the GPIO LIB API. Two calls are still
unimplemented though: irq_to_gpio and gpio_to_irq.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[TCP]: Add return value indication to tcp_prune_ofo_queue().
PS3: gelic: fix the oops on the broken IE returned from the hypervisor
b43legacy: fix DMA mapping leakage
mac80211: remove message on receiving unexpected unencrypted frames
Update rt2x00 MAINTAINERS entry
Add rfkill to MAINTAINERS file
rfkill: Fix device type check when toggling states
b43legacy: Fix usage of struct device used for DMAing
ssb: Fix usage of struct device used for DMAing
MAINTAINERS: move to generic repository for iwlwifi
b43legacy: fix initvals loading on bcm4303
rtl8187: Add missing priv->vif assignments
netconsole: only set CON_PRINTBUFFER if the user specifies a netconsole
[CAN]: Update documentation of struct sockaddr_can
MAINTAINERS: isdn4linux@listserv.isdn4linux.de is subscribers-only
[TCP]: Fix never pruned tcp out-of-order queue.
[NET_SCHED] sch_api: fix qdisc_tree_decrease_qlen() loop
As shown by Gurudas Pai recently, we can put hugepages into the surplus
state (by echo 0 > /proc/sys/vm/nr_hugepages), even when
/proc/sys/vm/nr_overcommit_hugepages is 0. This is actually correct, to
allow the original goal (shrink the static pool to 0) to succeed (we are
converting hugepages to surplus because they are in use). However, the
documentation does not accurately reflect this case. Update it.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A couple of typos crept into the newly added document about the seq_file
interface. This patch corrects those typos and simultaneously deletes
unnecessary trailing spaces.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the device tree bindings for the Marvell mv64x60 series of
system controller chips in booting-without-of.text.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The struct sockaddr_can has been simplified in the code review
process. This patch updates this simplification also in the
associated documentation in can.txt .
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert P. J. Day spotted that my removal of the Sangoma drivers missed
a few bits.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'docs' of git://git.lwn.net/linux-2.6:
Add additional examples in Documentation/spinlocks.txt
Move sched-rt-group.txt to scheduler/
Documentation: move rpc-cache.txt to filesystems/
Documentation: move nfsroot.txt to filesystems/
Spell out behavior of atomic_dec_and_lock() in kerneldoc
Fix a typo in highres.txt
Fixes to the seq_file document
Fill out information on patch tags in SubmittingPatches
Add the seq_file documentation
Checkpatch will throw an error if code doesn't use the correct initializers
for static spinlocks:
ERROR: Use of SPIN_LOCK_UNLOCKED is deprecated: see Documentation/spinlocks.txt
This is fine, but Documentation/spinlocks.txt isn't very clear on how to
_use_ the new initializers for static variables. To save people time in the
future, I added two small examples of how to fix old-style static
initializers to be more lockdep friendly.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This file is nfs-related. (Maybe Documentation/filesystems/ would
benefit from a separate nfs/ directory at some point.)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Documentation/ is a little large, and filesystems/ seems an obvious
place for this file.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Update SPI documentation to clarify some areas of recent confusion: clock
polarity takes effect when chipselect goes active; and zero length buffers are
OK in certain cases.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show the current binary tape driver and mode options is sysfs. A file
(options) is created in each directory in /sys/class/scsi_tape. The files
contain masks showing the options. The mask bit definitions are the same as
used when setting the options using the MTSETDRVBUFFER function in the
MTIOCTOP ioctl (defined in include/linux/mtio.h). For example:
> cat /sys/class/scsi_tape/nst0/options
0x00000d07
[jejb: updated doc with correction from Randy Dunlap]
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add new option MT_ST_SILI to enable setting the SILI bit in reads in variable
block mode. If SILI is set, reading a block shorter than the byte count does
not result in CHECK CONDITION. The length of the block is determined using the
residual count from the HBA. Avoiding the REQUEST SENSE command for every
block speeds up some real applications considerably.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The effects of cgroup_disable=foo are:
- foo isn't auto-mounted if you mount all cgroups in a single hierarchy
- foo isn't visible as an individually mountable subsystem
As a result there will only ever be one call to foo->create(), at init time;
all processes will stay in this group, and the group will never be mounted on
a visible hierarchy. Any additional effects (e.g. not allocating metadata)
are up to the foo subsystem.
This doesn't handle early_init subsystems (their "disabled" bit isn't set be,
but it could easily be extended to do so if any of the early_init systems
wanted it - I think it would just involve some nastier parameter processing
since it would occur before the command-line argument parser had been run.
Hugh said:
Ballpark figures, I'm trying to get this question out rather than
processing the exact numbers: CONFIG_CGROUP_MEM_RES_CTLR adds 15% overhead
to the affected paths, booting with cgroup_disable=memory cuts that back to
1% overhead (due to slightly bigger struct page).
I'm no expert on distros, they may have no interest whatever in
CONFIG_CGROUP_MEM_RES_CTLR=y; and the rest of us can easily build with or
without it, or apply the cgroup_disable=memory patches.
Unix bench's execl test result on x86_64 was
== just after boot without mounting any cgroup fs.==
mem_cgorup=off : Execl Throughput 43.0 3150.1 732.6
mem_cgroup=on : Execl Throughput 43.0 2932.6 682.0
==
[lizf@cn.fujitsu.com: fix boot option parsing]
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Sudhir Kumar <skumar@linux.vnet.ibm.com>
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch defines kernel parameter "nptcg=". The parameter overrides max number
of concurrent global TLB purges which is reported from either PAL_VM_SUMMARY or
SAL PALO.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch deletes a couple of superfluous word occurrences in the
document Documentation/unaligned-memory-access.txt.
Thanks to Sebastien Dugue for the remark about English usage.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
[VLAN]: Proc entry is not renamed when vlan device name changes.
[IPV6]: Fix ICMP relookup error path dst leak
[ATM] drivers/atm/iphase.c: compilation warning fix
IPv6: do not create temporary adresses with too short preferred lifetime
IPv6: only update the lifetime of the relevant temporary address
bluetooth : __rfcomm_dlc_close lock fix
bluetooth : use lockdep sub-classes for diffrent bluetooth protocol
[ROSE/AX25] af_rose: rose_release() fix
mac80211: correct use_short_preamble handling
b43: Fix PCMCIA IRQ routing
b43: Add DMA mapping failure messages
mac80211: trigger ieee80211_sta_work after opening interface
[LLC]: skb allocation size for responses
[IP] UDP: Use SEQ_START_TOKEN.
[NET]: Remove Documentation/networking/sk98lin.txt
[ATM] atm/idt77252.c: Make 2 functions static
[ATM]: Make atm/he.c:read_prom_byte() static
[IPV6] MCAST: Ensure to check multicast listener(s).
[LLC]: Kill llc_station_mac_sa symbol export.
forcedeth: fix locking bug with netconsole
...
Some time ago it turned out that our suspend code ordering broke some
NVidia-based systems that hung if _PTS was executed with one of the PCI
devices, specifically a USB controller, in a low power state.
Then, it was noticed that the suspend code ordering was not compliant
with ACPI 1.0, although it was compliant with ACPI 2.0 (and later), and
it was argued that the code had to be changed for that reason (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).
So we did, but evidently we did wrong, because it's now turning out that
some systems have been broken by this change. Refs:
http://bugzilla.kernel.org/show_bug.cgi?id=10340https://bugzilla.novell.com/show_bug.cgi?id=374217#c16
[ I said at that time that something like this might happend, but the
majority of people involved thought that it was improbable due to the
necessity to preserve the compliance of hardware with ACPI 1.0. ]
This actually is a quite serious regression from 2.6.24.
Moreover, the ACPI 1.0 ordering of suspend code introduced another issue
that I have only noticed recently. Namely, if the suspend of one of
devices fails, the already suspended devices will be resumed without
executing _WAK before, which leads to problems on some systems (for
example, in such situations thermal management is broken on my HP
nx6325). Consequently, it also breaks suspend debugging on the affected
systems.
Note also, that the requirement to execute _PTS before suspending
devices does not really make sense, because the device in question may
be put into a low power state at run time for a reason unrelated to a
system-wide suspend.
For the reasons outlined above, the change of the suspend ordering
should be reverted, which is done by the patch below.
[ Felix Möller: "I am the reporter from the original Novell Bug:
https://bugzilla.novell.com/show_bug.cgi?id=374217
I just tried current git head (two hours ago) with the patch (the one
from the beginning of this thread) from Rafael and without it. With
the patch my MacBook does suspend without it does not." ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Felix Möller <felix@derklecks.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Old-world powermacs don't set L2CR or L3CR on processor upgrade cards.
This simple patch allows the setting of L3CR via a kernel parameter
(like the existing kernel parameter to set L2CR).
Signed-off-by: Robert Brose <bob@qbjnet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the driver is gone there's no point in keeping the documentation.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Friday 2008-03-28 19:20, Jonathan Corbet wrote:
>commit 9756ccfda31b4c4544aa010aacf71b6672d668e8
>Date: Fri Mar 28 11:19:56 2008 -0600
>
> Add the seq_file documentation
patch on top:
- add const qualifiers
- remove void* casts
- use proper specifier (%Ld is not valid)
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Add more information about the various patch tags in use, and try to
establish a meaning for Reviewed-by:
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Took some cycles to re-read the Lguest Journey end-to-end, fix some
rot and tighten some phrases.
Only comments change. No new jokes, but a couple of recycled old jokes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Mention the config options for the Virtio drivers and move the Virtualization
menu to the toplevel.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The description of the interrupt routing doesn't match the (nice) diagram.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.
The now obsolete linux,network-index properties are removed from the
corresponding device trees. This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.
The references to linux,network-index are removed from
booting-without-of.txt. Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree. By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Update documentation for the hw_random support to be current:
- Documentation/hw_random.txt has been updated to reflect the
current code: it's a framework now, a "core" with a small
sysfs interface, that hardware-specific drivers plug in to.
Text specific to Intel hardware is now at the end.
- Kconfig now references the Documentation/hw_random.txt file
and better explains what this really does.
Both chunks of documentation now higlight the fact that the kernel entropy
pool is maintained by "rngd", and this driver has nothing directly to do with
that important task.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide example for memmap exclude option (it is slightly strange and
non-trivial) and provide nice small HOWTO for people with bad memory.
Signed-off-by: Jan-Simon Moeller <dl9pf@gmx.de>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit d48567dd43.
Borislav is working on ide-tape "light" version instead.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted
(they are layering violation and should be dealt with in the same
way as done by libata - device-mapper should be used instead).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark "hdx=[driver_name]" and "hdx=scsi" kernel parameters as obsoleted
(nowadays device-driver binding can be changed at runtime through sysfs
and it can also be dealt with using per device driver parameters).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* "hdx=cyls,heads,sects,wpcom,irq" should be "hdx=cyls,heads,sects".
* "hdx=" is for "x" from 'a' to 'u', "idex=" is for "x" from '0' to '9'.
* "idex=noautotune" is long gone.
* Obsoleted "ide0=" parameters were already removed from the documentation.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Implement support for the E-Ink Metronome controller. It provides an mmapable
interface to the controller using defio support. It was tested with a gumstix
pxa255 with Vizplex media using Xfbdev and various X clients such as xeyes,
xpdf, xloadimage.
This patch also fixes the following bug: Defio would cause a hang on write
access to the framebuffer as the page fault would be called ad-infinitum. It
fixes fb_defio by setting the mapping to be used by page_mkclean.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
no longer working for some time.
A driver that had been marked as BROKEN for such a long time seems to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still present in
the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This essentially reverts commit 71fc47a9ad
("ACPI: basic initramfs DSDT override support"), because the code simply
isn't ready.
It did ugly things to the init sequence to populate the rootfs image
early, but that just ended up showing other problems with the whole
approach. The fact is, the VFS layer simply isn't initialized this
early, and the relevant ACPI code should either run much later, or this
shouldn't be done at all.
For 2.6.25, we'll just pick the latter option. We can revisit this
concept later if necessary.
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Markus Gaugusch <dsdt@gaugusch.at>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <Larry.Finger@lwfinger.net>
Cc: <stefano.brivio@polimi.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move 00-INDEX entries to power/00-INDEX (and add entry for
pm_qos_interface.txt).
Update references to moved filenames.
Fix some trailing whitespace.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move laptop-mode.txt into the laptops/ sub-directory to consolidate
laptop doc files there.
Update references to the file's location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The mail LED name for acer-wmi currently hardcodes in the colour as green.
This is wrong, since many of the newer laptops now come with an orange
LED, and we have no way of telling what colour is used on a given system.
Also, rename the mail LED to be inline with the current recommendations of
the LED class documentation.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Do not append space to guests kernel command line
lguest: Revert 1ce70c4fac, fix real problem.
lguest: Sanitize the lguest clock.
lguest: fix __get_vm_area usage.
lguest: make sure cpu is initialized before accessing it
I have found a very small typo in Documentation/scheduler/sched-stats.txt.
See the end of this mail.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This macro is used to define tables, not to declare them.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lguest launcher appends a space to the kernel command line (if kernel
arguments are specified on its command line). This space is unneeded. More
importantly, this appended space will make Red Hat's nash script interpreter
(used in a Fedora style initramfs) add an empty argument to init's command
line. This empty argument will make kernel arguments like "init=/bin/bash"
fail (because the shell will try to execute a script with an empty name).
This could be considered a bug in nash, but is easily fixed in the lguest
launcher too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'slab-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/christoph/vm:
slub: fix typo in Documentation/vm/slub.txt
slab: NUMA slab allocator migration bugfix
slub: Do not cross cacheline boundaries for very small objects
slab - use angle brackets for include of kmalloc_sizes.h
slab numa fallback logic: Do not pass unfiltered flags to page allocator
slub statistics: Fix check for DEACTIVATE_REMOTE_FREES
Cleanup some of Documentation directory:
Move Documentation/ide.txt to the ide/ sub-directory.
Fix trailing whitespace while there.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
slub_debug=,dentry is correct, not dentry_cache.
Signed-off-by: Itaru Kitayama <i-kitayama@ap.jp.nec.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Quite a while ago I started this book. The required kernel-doc
patches have since gone into the tree so it is now possible to
build the book in mainline.
The actual documentation is still rather incomplete and not all
things are linked into the book, but this enables us to edit
the documentation collaboratively, hopefully driver authors can
add documentation based on their experience with mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename Memory Controller to Memory Resource Controller. Reflect the same
changes in the CONFIG definition for the Memory Resource Controller. Group
together the config options for Resource Counters and Memory Resource
Controller.
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move kprobes examples from Documentation/kprobes.txt to under samples/.
Patch originally by Randy Dunlap.
o Updated the patch to apply on 2.6.25-rc3
o Modified examples code to build on multiple architectures. Currently,
the kprobe and jprobe examples code works for x86 and powerpc
o Cleaned up unneeded #includes
o Cleaned up Kconfig per Sam Ravnborg's suggestions to fix build break
on archs that don't have kretprobes
o Implemented suggestions by Mathieu Desnoyers on CONFIG_KRETPROBES
o Included Andrew Morton's cleanup based on x86-git
o Modified kretprobe_example to act as a arch-agnostic module to
determine routine execution times:
Use 'modprobe kretprobe_example func=<func_name>' to determine
execution time of func_name in nanoseconds.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a <linux/gpio.h> defining fail/warn stubs for GPIO calls on platforms that
don't support the GPIO programming interface. That includes the arch-specific
implementation glue otherwise.
This facilitates a new model for GPIO usage: drivers that can use GPIOs if
they're available, but don't require them. One example of such a driver is
NAND driver for various FreeScale chips. On platforms update with GPIO
support, they can be used instead of a worst-case delay to verify that the
BUSY signal is off.
(Also includes a couple minor unrelated doc updates.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memory controller has a requirement that while writing values, we need
to use echo -n. This patch fixes the problem and makes the UI more consistent.
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The definitions of struct pci_device_id arrays should generally follow
the same pattern across the entire kernel. This macro defines this
array as const and puts it into the __devinitconst section.
There are currently many definitions scattered about the kernel that
omit the __devinitdata modifier despite the documentation stating that
it should always be there. These definitions really also should have
been const, which wasn't possible before but has become so with the
addition of the __devinitconst attribute.
Furthermore, there are definitions that use "const" and __devinitdata,
which is explicitly wrong but the compiler doesn't catch section
mismatches if there's only one such one case in the module (which is
often the case).
Adding the __devinitconst modifier where there was nothing before buys
us memory. Adding the const modifier gives the compiler a chance to do
its thing. Changing __devinitdata to __devinitconst where it was wrong
actually fixes some compiler errors in older (mid-release) kernels that
were patched over by "removing" the section attribute altogether (which
wastes memory).
This macro makes it pretty difficult to get this definition wrong in
the future...
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The fix up from Daniel Drake for replacing GFP_DMA with something
more sensible has gone in here:
commit 69e562c234
Author: Daniel Drake <dsd@gentoo.org>
Date: Wed Feb 20 13:29:05 2008 +0000
[SCSI] arcmsr: fix message allocation
add a change log and update the version for this.
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
delay the removal of this symbol export by one more kernel release,
giving external modules such as VirtualBox a chance to stop using it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: remove stale comments from ide-dma.c (take 2)
ide: remove ide-tape documentation from Documentation/ide.txt
qd65xx: remove commented out code
ide-tape: schedule driver for removal after 6 months
ide-disk: add missing printk() KERN_* levels
ide: fix sparse warning about shadowing 'flags' symbol
ide-cd: fix CD/DVD burning
ide-cd: fix 'ireason' handling for REQ_TYPE_ATA_PC requests
qd65xx: fix setup of QD6580 Control register
ide: skip probing port if "hdx=noprobe" was used for both devices on it
ide: remove redundant comment from ide_unregister()
hpt366: fix section mismatch warnings
ide-cd: Enable audio play quirk for Optiarc DVD RW AD-5200A drive
* Skip probing port if "hdx=noprobe" parameter was used for both devices on it.
* Obsolete "idex=noprobe" parameter - it only works for ide_generic, cmd640
and PCI hosts in Compatibility mode (on alpha/x86/ia64/m32r/mips/ppc32).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
(sorry for being offtpoic, but while experts are here...)
A "typical" implementation of atomic_add_unless() can return 0 immediately
after the first atomic_read() (before doing cmpxchg). In that case it doesn't
provide any barrier semantics. See include/asm-ia64/atomic.h as an example.
We should either change the implementation, or fix the docs.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Misc fixes and updates, make the doc consistent with current cgroup
implementation.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current implementation of cpuset track N_HIGH_MEMORY instead N_MEMORY.
(N_MEMORY doesn't exist in current implementation)
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
stable_kernel_rules: fix must already be in mainline
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I keep running upstream and mm kernels and the location of the slab
directory is different since upstream still uses /sys/slab. This patch
makes slabinfo check /sys/slab if /sys/kernel/slab is not there. Makes
slabinfo work on any kernel.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the UTF-8 broken encodings in the ja_JP version of stable_kernel_rules.txt
From: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements libata.force module parameter which can
selectively override ATA port, link and device configurations
including cable type, SATA PHY SPD limit, transfer mode and NCQ.
For example, you can say "use 1.5Gbps for all fan-out ports attached
to the second port but allow 3.0Gbps for the PMP device itself, oh,
the device attached to the third fan-out port chokes on NCQ and
shouldn't go over UDMA4" by the following.
libata.force=2:1.5g,2.15:3.0g,2.03:noncq,udma4
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (32 commits)
x86: fix page_is_ram() thinko
x86: fix WARN_ON() message: teach page_is_ram() about the special 4Kb bios data page
x86: i8259A: remove redundant irq_descinitialization
x86: fix vdso_install breaks user "make install"
x86: change IO delay back to 0x80
x86: lds - Use THREAD_SIZE instead of numeric constant
x86: lds - Use PAGE_SIZE instead of numeric constant
x86 cleanup: suspend_asm_64.S - use X86_CR4_PGE instead of numeric value
x86: docs fixes to Documentation/i386/IO-APIC.txt
x86: fix printout ugliness in cpu info printk
x86: clean up csum-wrappers_64.c some more
x86: coding style fixes in arch/x86/lib/csum-wrappers_64.c
x86: coding style fixes in arch/x86/lib/io_64.c
x86: exclude vsyscall files from stackprotect
x86: add pgd_large() on 64-bit, for consistency
x86: minor cleanup of comments in processor.h
x86: annotate pci/common.s:pci_scan_bus_with_sysdata with __devinit
x86: fix section mismatch in head_64.S:initial_code
x86: fix section mismatch in srat_64.c:reserve_hotadd
x86: fix section mismatch warning in topology.c:arch_register_cpu
...
Rectify a factoid about firewire-ohci.
Acked-by: Ingo Molnar <mingo@elte.hu>
Also fix a typo spotted by Bernhard Kaindl.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
[NIU]: Bump driver version and release date.
[NIU]: Fix BMAC alternate MAC address indexing.
net: fix kernel-doc warnings in header files
[IPV6]: Use BUG_ON instead of if + BUG in fib6_del_route.
[IPV6]: dst_entry leak in ip4ip6_err. (resend)
bluetooth: do not move child device other than rfcomm
bluetooth: put hci dev after del conn
[NET]: Elminate spurious print_mac() calls.
[BLUETOOTH] hci_sysfs.c: Kill build warning.
[NET]: Remove MAC_FMT
net/8021q/vlan_dev.c: Use print_mac.
[XFRM]: Fix ordering issue in xfrm_dst_hash_transfer().
[BLUETOOTH] net/bluetooth/hci_core.c: Use time_* macros
[IPV6]: Fix hardcoded removing of old module code
[NETLABEL]: Move some initialization code into __init section.
[NETLABEL]: Shrink the genl-ops registration code.
[AX25] ax25_out: check skb for NULL in ax25_kick()
[TCP]: Fix tcp_v4_send_synack() comment
[IPV4]: fix alignment of IP-Config output
Documentation: fix tcp.txt
...
Clean up spelling and grammar of IO-APIC.txt
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the mca-pentium boot option that was a noop.
besides the source code cleanup factor, this saves some text as well:
arch/x86/kernel/cpu/bugs.o:
text data bss dec hex filename
651 77 4 732 2dc bugs.o.before
631 53 4 688 2b0 bugs.o.after
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Thanks to Angelo Lisco for his initial patch we missed and to
Ahmet Dogan Ugurel confirming such a device functional.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for analog inputs and DVB-T.
Good sensitivity for DVB-T currently needs to use analog TV first.
DVB-S support is not yet completed, but is on the way.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
S-Video is unconfirmed, but likely correct.
The remote is not yet investigated.
Thanks go to Sioux for providing code and asking to fix the auto
detection.
Signed-off-by: sioux <sioux_it@libero.it>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Replace BIC with CUBIC as default congestion control. Fix grammar.
Signed-off-by: Matti Linnanvuori <mattilinnanvuori@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for family 0x17, which has Penryn Core. It should also
cover the 8 cores Xeons.
Can someone test please? I think it should work.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Following patch will add reporting of maximum temperature, at which all fans
should spin full speed. It may be non-physical temperature on Desktop/Server CPUs.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
A quick study of the 0x5009/0x500A HKEY event on the X61t DSDT revealed the
existence of the EC HTAB register (EC 0x0f, bit 7), and a compare with the
X41t DSDT shows that HKEY.MHKG can be used to verify if the ThinkPad is
tablet-capable (MHKG present), and in tablet mode (bit 3 of MHKG return is
set).
Add an attribute to report this information, "hotkey_tablet_mode". This
attribute has poll()/select() support, and can be used along with EV_SW
SW_TABLET_MODE to hook userspace to tablet events.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes some minor points in the radio switch code and docs.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a few spelling errors, and also document the EV_SW events thinkpad-acpi
can issue.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Issue EV_SW SW_TABLET_MODE events for HKEY events 0x5009 and 0x500A on the
X41t/X60t/X61t. As usual, we suppress the HKEY events on the netlink
interface to avoid sending duplicate events to userspace.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a stray ibm-acpi that should have been replaced with thinkpad-acpi.
Thanks to Damjan <gdamjan@mail.net.mk> for noticing this one.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Documentation for cpuidle infrastructure. (resend)
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes a reference to Documentation/kmod.txt
which was apparently renamed to Documentation/debugging-modules.txt
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop z85230 support library info from kernel-api since it's duplicated in
the Z85230 book.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move networking (core and drivers) docbook to its own networking book.
Fix a few kernel-doc errors in header and source files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use updated file list for docbook files and
fix kernel-doc warnings in sunrpc:
Warning(linux-2.6.24-git12//net/sunrpc/rpc_pipe.c:689): No description found for parameter 'rpc_client'
Warning(linux-2.6.24-git12//net/sunrpc/rpc_pipe.c:765): No description found for parameter 'flags'
Warning(linux-2.6.24-git12//net/sunrpc/clnt.c:584): No description found for parameter 'tk_ops'
Warning(linux-2.6.24-git12//net/sunrpc/clnt.c:618): No description found for parameter 'bufsize'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move pipes and splice docbook to filesystems book.
kernel-api book is huge (10x most other books) & slow to process.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel style is mentioned twice, and the git apply trick is a bit redundant
given the checkpatch.pl recommendation (which also checks for bad
whitespace).
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fastcall always expands to empty, remove it.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the rt_ratio interface to rt_runtime_us, to match rt_period_us.
This avoids picking a granularity for the ratio.
Extend the /sys/kernel/uids/<uid>/ interface to allow setting
the group's rt_runtime.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Other than the defconfigs, remove the entry in compiler-gcc4.h,
Kconfig.debug and feature-removal-schedule.txt.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add some initial documentation detailing what acer-wmi is, and how to use
it. Update the Kconfig entry with a reference to the documentation.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to sonypi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to sony-laptop.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to thinkpad-acpi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
There are currently various laptop drivers floating about with no central
place for their documentation, which is currently scattered around the top
level Documentation/ directory.
So, as a first step, lets create a Documentation sub-directory, and update
the relevant index files. The work of then moving the existing laptop
driver related documentation will then be handled later.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix gcc warnings in getdelays.c:
Documentation/accounting/getdelays.c: In function 'task_context_switch_counts':
Documentation/accounting/getdelays.c:214: warning: format '%15lu' expects type 'long unsigned int', but argument 4 has type '__u64'
Documentation/accounting/getdelays.c:214: warning: format '%15lu' expects type 'long unsigned int', but argument 5 has type '__u64'
Documentation/accounting/getdelays.c: In function 'main':
Documentation/accounting/getdelays.c:402: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
Documentation/accounting/getdelays.c: In function 'get_family_id':
Documentation/accounting/getdelays.c:171: warning: 'id' may be used uninitialized in this function
One warning is not a problem and can be dismissed:
Documentation/accounting/getdelays.c: In function 'main':
Documentation/accounting/getdelays.c:236: warning: 'cmd_type' may be used uninitialized in this function
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following the deprecation schedule the a.out ELF interpreter support
is removed now with this patch. a.out ELF interpreters were an transition
feature for moving a.out systems to ELF, but they're unlikely to be still
needed. Pure a.out systems will still work of course. This allows to
simplify the hairy ELF loader.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series addresses the problem of showing mount options in
/proc/mounts.
Several filesystems which use mount options, have not implemented a
.show_options superblock operation. Several others have implemented
this callback, but have not kept it fully up to date with the parsed
options.
Q: Why do we need correct option showing in /proc/mounts?
A: We want /proc/mounts to fully replace /etc/mtab. The reasons for
this are:
- unprivileged mounters won't be able to update /etc/mtab
- /etc/mtab doesn't work with private mount namespaces
- /etc/mtab can become out-of-sync with reality
Q: Can't this be done, so that filesystems need not bother with
implementing a .show_mounts callback, and keeping it up to date?
A: Only in some cases. Certain filesystems allow modification of a
subset of options in their remount_fs method. It is not possible
to take this into account without knowing exactly how the
filesystem handles options.
For the simple case (no remount or remount resets all options) the
patchset introduces two helpers:
generic_show_options()
save_mount_options()
These can also be used to emulate the old /etc/mtab behavior, until
proper support is added. Even if this is not 100% correct, it's still
better than showing no options at all.
The following patches fix up most in-tree filesystems, some have been
compile tested only, some have been reviewed and acked by the
maintainer.
Table displaying status of all in-kernel filesystems:
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
legend:
none - fs has options, but doesn't define ->show_options()
some - fs defines ->show_options(), but some only options are shown
good - fs shows all options
noopt - fs does not have options
patch - a patch will be posted
merged - a patch has been merged by subsystem maintainer
9p good
adfs patch
affs patch
afs patch
autofs patch
autofs4 patch
befs patch
bfs noopt
cifs some
coda noopt
configfs noopt
cramfs noopt
debugfs noopt
devpts patch
ecryptfs good
efs noopt
ext2 patch
ext3 good
ext4 merged
fat patch
freevxfs noopt
fuse patch
fusectl noopt
gfs2 good
gfs2meta noopt
hfs good
hfsplus good
hostfs patch
hpfs patch
hppfs noopt
hugetlbfs patch
isofs patch
jffs2 noopt
jfs merged
minix noopt
msdos ->fat
ncpfs patch
nfs some
nfsd noopt
ntfs good
ocfs2 good
ocfs2/dlmfs noopt
openpromfs noopt
proc noopt
qnx4 noopt
ramfs noopt
reiserfs patch
romfs noopt
smbfs good
sysfs noopt
sysv noopt
udf patch
ufs good
vfat ->fat
xfs good
mm/shmem.c patch
drivers/oprofile/oprofilefs.c noopt
drivers/infiniband/hw/ipath/ipath_fs.c noopt
drivers/misc/ibmasm/ibmasmfs.c noopt
drivers/usb/core (usbfs) merged
drivers/usb/gadget (gadgetfs) noopt
drivers/isdn/capi/capifs.c patch
kernel/cpuset.c noopt
fs/binfmt_misc.c noopt
net/sunrpc/rpc_pipe.c noopt
arch/powerpc/platforms/cell/spufs patch
arch/s390/hypfs good
ipc/mqueue.c noopt
security (securityfs) noopt
security/selinux/selinuxfs.c noopt
kernel/cgroup.c good
security/smack/smackfs.c noopt
in -mm:
reiser4 some
unionfs good
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
This patch:
Document the rules for handling mount options in the .show_options
super operation.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement dmode option for iso9660 filesystem to allow setting of access
rights for directories on the filesystem.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: "Ilya N. Golubev" <gin@mo.msk.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>