Currently vlan group is searched using one key - the ifindex.
We'll have to lookup the vlan_group by two keys - ifindex and
net. Turning the vlan_group lookup key to struct net_device
pointer will make this process easier.
Besides, this will eliminate one more place in the networking,
that assumes that indexes are unique in the kernel.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is responsible for calling ->dellink on each net
device found in net to help with vlan net_exit hook in the
nearest future.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each potential list_del (happening from inside a ->dellink call)
is followed by goto restart, so there's no need in _safe iteration.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed can only be more strict than what was checked by the
earlier common case check for non-tail skbs, thus
cwnd_len <= needed will never match in that case anyway.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returns non-zero if tp->out_of_order_queue was seen non-empty.
This allows tcp_try_rmem_schedule() to return early.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is not possible to read/write to an eeprom larger than
128k in size because the buffer used for temporarily storing the
eeprom contents is allocated using kmalloc. kmalloc can only allocate
a maximum of 128k depending on architecture.
Modified ethtool_get/set_eeprom to only allocate a page of memory and
then copy the eeprom a page at a time.
Updated original patch as per suggestions from Joe Perches.
Signed-off-by: Mandeep Singh Baines <msb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of hrtimers to support high resolution capabilities, when
provided by the system clocksource.
The conversion to hrtimers additionally discovered and solved an
unlikely race condition that has been reproduced under (unrealistic)
massive receive load, which can only be produced on vcan software devices.
[ Fix printf format warnings on 64-bit -DaveM ]
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that TIPC properly handles incoming messages
that have incorrect or unexpected formats. Most significantly,
it now ensures that each sl_buff has at least as much data as
the message header indicates it should, and that the entire
message header is stored contiguously; this prevents TIPC from
accidentally accessing memory that is not part of the sk_buff.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows TIPC to process incoming messages that are
stored in a fragmented sk_buff, by forcing the linearization
of any such messages it receives.
Note: This is an interim solution to allow TIPC to operate with
Ethernet devices that generate non-linear buffers (such as the
gianfar driver), until such time as the rest of TIPC is enhanced
to handle sk_buffs with multiple data areas.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch causes TIPC to allocate fast clonable sk_buffs,
rather than standard ones. This speeds up the cloning
operation done by the link code each time a message is sent
off-node.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch eliminates a null pointer check when discarding a
TIPC message buffer, since kfree_skb() already handles this
situation.
Acknowledgements to Florian Westphal (fw@strlen.de> for
suggesting this enhancement.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some people are getting this message a lot, and we have traced it to
broken access points that much too often send completely empty frames
(all bytes zeroed, which they shouldn't do at all.)
Since we cannot do anything about such frames in any case except the
special case where we're debugging an AP, just remove the message.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill_switch_all() is supposed to only switch all the interfaces of a
given type, but does not actually do this; instead, it just switches
everything currently in the same state.
Add the necessary type check in.
(This fixes a bug I've been seeing while developing an rfkill laptop
driver, with both bluetooth and wireless simultaneously changing state
after only pressing either KEY_WLAN or KEY_BLUETOOTH).
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the elastic array of void * pointer to the struct net.
The access rules are simple:
1. register the ops with register_pernet_gen_device to get
the id of your private pointer
2. call net_assign_generic() to put the private data on the
struct net (most preferably this should be done in the
->init callback of the ops registered)
3. do not store any private reference on the net_generic array;
4. do not change this pointer while the net is alive;
5. use the net_generic() to get the pointer.
When adding a new pointer, I copy the old array, replace it
with a new one and schedule the old for kfree after an RCU
grace period.
Since the net_generic explores the net->gen array inside rcu
read section and once set the net->gen->ptr[x] pointer never
changes, this grants us a safe access to generic pointers.
Quoting Paul: "... RCU is protecting -only- the net_generic
structure that net_generic() is traversing, and the [pointer]
returned by net_generic() is protected by a reference counter
in the upper-level struct net."
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make some per-net generic pointers, we need some way to address
them, i.e. - IDs. This is simple IDA-based IDs generator for pernet
subsystems.
Addressing questions about potential checkpoint/restart problems:
these IDs are "lite-offsets" within the net structure and are by no
means supposed to be exported to the userspace.
Since it will be used in the nearest future by devices only (tun,
vlan, tunnels, bridge, etc), I make it resemble the functionality
of register_pernet_device().
The new ids is stored in the *id pointer _before_ calling the init
callback to make this id available in this callback.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_prune_queue() doesn't prune an out-of-order queue at all.
Therefore sk_rmem_schedule() can fail but the out-of-order queue isn't
pruned . This can lead to tcp deadlock state if the next two
conditions are held:
1. There are a sequence hole between last received in
order segment and segments enqueued to the out-of-order queue.
2. Size of all segments in the out-of-order queue is more than tcp_mem[2].
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even kernel 2.2.26 (sic) already contains the
#undef CONFIG_IRLAN_SEND_GRATUITOUS_ARP
with the comment "but for some reason the machine crashes if you use DHCP".
Either someone finally looks into this or it's simply time to remove
this dead code.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies TIPC's socket code to follow the same approach
used by other protocols. This change eliminates the need for a
mutex in the TIPC-specific portion of the socket protocol data
structure -- in its place, the standard Linux socket backlog queue
and associated locking routines are utilized. These changes fix
a long-standing receive queue bug on SMP systems, and also enable
individual read and write threads to utilize a socket without
unnecessarily interfering with each other.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes TIPC's connect routine to conform to Linux
kernel style norms of indentation, line length, etc.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch causes TIPC to return an error indication if the non-
blocking form of connect() is requested (which TIPC does not yet
support).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that allowed TIPC to queue 1 more message
than allowed by the socket receive queue threshold limits. The
patch also improves the threshold code's logic and naming to help
prevent this sort of error from recurring in the future.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that padding bytes appearing at the end of
an incoming TIPC message are not returned as valid stream data.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a stream socket to receive data from multiple
TIPC messages in its receive queue, without requiring the use of
the MSG_WAITALL flag.
Acknowledgements to Florian Westphal <fw-tipc@strlen.de> for
identifying this issue and suggesting how to correct it.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimizes the receive path for SOCK_DGRAM and SOCK_RDM
messages by skipping over code that handles connection-based flow
control.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC_H_MAJ(parentid) for root classes is the same as for ingress, and if
ingress qdisc is created qdisc_lookup() returns its pointer (without
ingress NULL is returned). After this all qdisc_lookups give the same,
and we get endless loop. (I don't know how this could hide for so long
- it should trigger with every leaf class deleted if it's qdisc isn't
empty.)
After this fix qdisc_lookup() is omitted both for ingress and root
parents, but looking for root is only wasting a little time here...
Many thanks to Enrico Demarin for finding a test for catching this
bug, which probably bothered quite a lot of admins.
Reported-by: Enrico Demarin <enrico@superclick.com>,
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SECURITY_NETWORK_XFRM is undefined the following warnings appears:
net/xfrm/xfrm_user.c: In function 'xfrm_add_pol_expire':
net/xfrm/xfrm_user.c:1576: warning: 'ctx' may be used uninitialized in this function
net/xfrm/xfrm_user.c: In function 'xfrm_get_policy':
net/xfrm/xfrm_user.c:1340: warning: 'ctx' may be used uninitialized in this function
(security_xfrm_policy_alloc is noop for the case).
It seems that they are result of the commit
03e1ad7b5d ("LSM: Make the Labeled IPsec
hooks more stack friendly")
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
[BRIDGE]: Fix crash in __ip_route_output_key with bridge netfilter
[NETFILTER]: ipt_CLUSTERIP: fix race between clusterip_config_find_get and _entry_put
[IPV6] ADDRCONF: Don't generate temporary address for ip6-ip6 interface.
[IPV6] ADDRCONF: Ensure disabling multicast RS even if privacy extensions are disabled.
[IPV6]: Use appropriate sock tclass setting for routing lookup.
[IPV6]: IPv6 extension header structures need to be packed.
[IPV6]: Fix ipv6 address fetching in raw6_icmp_error().
[NET]: Return more appropriate error from eth_validate_addr().
[ISDN]: Do not validate ISDN net device address prior to interface-up
[NET]: Fix kernel-doc for skb_segment
[SOCK] sk_stamp: should be initialized to ktime_set(-1L, 0)
net: check for underlength tap writes
net: make struct tun_struct private to tun.c
[SCTP]: IPv4 vs IPv6 addresses mess in sctp_inet[6]addr_event.
[SCTP]: Fix compiler warning about const qualifiers
[SCTP]: Fix protocol violation when receiving an error lenght INIT-ACK
[SCTP]: Add check for hmac_algo parameter in sctp_verify_param()
[NET_SCHED] cls_u32: refcounting fix for u32_delete()
[DCCP]: Fix skb->cb conflicts with IP
[AX25]: Potential ax25_uid_assoc-s leaks on module unload.
...
I was asked about "why don't we perform a sk_net filtering in
bind_conflict calls, like we do in other sock lookup places"
for a couple of times.
Can we please add a comment about why we do not need one?
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These sockets now have a bit other names and are no longer global.
Shame on me, I haven't provided a good comment for this when
sending DCCP netnsization patches.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ebtables nflog watcher to the kernel in order to
allow ebtables log through the nfnetlink_log backend.
Signed-off-by: Peter Warasin <peter@endian.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Directly call IPv4 and IPv6 variants where the address family is
easily known.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Invalid states can cause out-of-bound memory accesses of the state table.
Also don't insist on having a new state contained in the netlink message.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Connection tracking helpers (specifically FTP) need to be called
before NAT sequence numbers adjustments are performed to be able
to compare them against previously seen ones. We've introduced
two new hooks around 2.6.11 to maintain this ordering when NAT
modules were changed to get called from conntrack helpers directly.
The cost of netfilter hooks is quite high and sequence number
adjustments are only rarely needed however. Add a RCU-protected
sequence number adjustment function pointer and call it from
IPv4 conntrack after calling the helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
New extensions may only be added to unconfirmed conntracks to avoid races
when reallocating the storage.
Also change NF_CT_ASSERT to use WARN_ON to get backtraces.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Adding extensions to confirmed conntracks is not allowed to avoid races
on reallocation. Don't setup NAT for confirmed conntracks in case NAT
module is loaded late.
The has one side-effect, the connections existing before the NAT module
was loaded won't enter the bysource hash. The only case where this actually
makes a difference is in case of SNAT to a multirange where the IP before
NAT is also part of the range. Since old connections don't enter the
bysource hash the first new connection from the IP will have a new address
selected. This shouldn't matter at all.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Locally generated ICMP packets have a reference to the conntrack entry
of the original packet manually attached by icmp_send(). Therefore the
check for locally originated untracked ICMP redirects can never be
true.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Move the UDP-Lite conntrack checksum validation to a generic helper
similar to nf_checksum() and make it fall back to nf_checksum()
in case the full packet is to be checksummed and hardware checksums
are available. This is to be used by DCCP conntrack, which also
needs to verify partial checksums.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Move responsibility for setting the IP_NAT_RANGE_PROTO_SPECIFIED flag
to the NAT protocol, properly propagate errors and get rid of ugly
return value convention.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Move to nf_nat_proto_common and rename to nf_nat_proto_... since they're
also used by protocols that don't have port numbers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
The port rover should not get overwritten when using random mode,
otherwise other rules will also use more or less random ports.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Rule dumping is performed in two steps: first userspace gets the
ruleset size using getsockopt(SO_GET_INFO) and allocates memory,
then it calls getsockopt(SO_GET_ENTRIES) to actually dump the
ruleset. When another process changes the ruleset in between the
sizes from the first getsockopt call doesn't match anymore and
the kernel aborts. Unfortunately it returns EAGAIN, as for multiple
other possible errors, so userspace can't distinguish this case
from real errors.
Return EAGAIN so userspace can retry the operation.
Fixes (with current iptables SVN version) netfilter bugzilla #104.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Some callers pass uninitialized structures, clear the address to make
sure later comparisions work properly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit 9335f047fe aka
"[NETFILTER]: ip_tables: per-netns FILTER, MANGLE, RAW"
added per-netns _view_ of iptables rules. They were shown to user, but
ignored by filtering code. Now that it's possible to at least ping loopback,
per-netns tables can affect filtering decisions.
netns is taken in case of
PRE_ROUTING, LOCAL_IN -- from in device,
POST_ROUTING, LOCAL_OUT -- from out device,
FORWARD -- from in device which should be equal to out device's netns.
This code is relatively new, so BUG_ON was plugged.
Wrappers were added to a) keep code the same from CONFIG_NET_NS=n users
(overwhelming majority), b) consolidate code in one place -- similar
changes will be done in ipv6 and arp netfilter code.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Dump the mark value in log messages similar to nfnetlink_log. This
is useful for debugging complex setups where marks are used for
routing or traffic classification.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Patch splits creation of /proc/net/nf_conntrack, /proc/net/stat/nf_conntrack
and net.netfilter hierarchy into their own functions with dummy ones
if PROC_FS or SYSCTL is not set. Also, remove dead "ret = 0" write
while I'm at it.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The bridge netfilter code attaches a fake dst_entry with a pointer to a
fake net_device structure to skbs it passes up to IPv4 netfilter. This
leads to crashes when the skb is passed to __ip_route_output_key when
dereferencing the namespace pointer.
Since bridging can currently only operate in the init_net namespace,
the easiest fix for now is to initialize the nd_net pointer of the
fake net_device struct to &init_net.
Should fix bugzilla 10323: http://bugzilla.kernel.org/show_bug.cgi?id=10323
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider we are putting a clusterip_config entry with the "entries"
count == 1, and on the other CPU there's a clusterip_config_find_get
in progress:
CPU1: CPU2:
clusterip_config_entry_put: clusterip_config_find_get:
if (atomic_dec_and_test(&c->entries)) {
/* true */
read_lock_bh(&clusterip_lock);
c = __clusterip_config_find(clusterip);
/* found - it's still in list */
...
atomic_inc(&c->entries);
read_unlock_bh(&clusterip_lock);
write_lock_bh(&clusterip_lock);
list_del(&c->list);
write_unlock_bh(&clusterip_lock);
...
dev_put(c->dev);
Oops! We have an entry returned by the clusterip_config_find_get,
which is a) not in list b) has a stale dev pointer.
The problems will happen when the CPU2 will release the entry - it
will remove it from the list for the 2nd time, thus spoiling it, and
will put a stale dev pointer.
The fix is to make atomic_dec_and_test under the clusterip_lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This expresses __skb_append in terms of __skb_queue_after, exploiting that
__skb_append(old, new, list) = __skb_queue_after(list, old, new).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches adds a call to increment IPSTATS_MIB_OUTFORWDATAGRAMS
when forwarding the packet in ip6_mr_forward() in the IPv6 multicast
routing module (net/ipv6/ip6mr.c).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As far as I can remember, I was going to disable privacy extensions
on all "tunnel" interfaces. Disable it on ip6-ip6 interface as well.
Also, just remove ifdefs for SIT for simplicity.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since NETDEV_REGISTER notifier chain is responsible for creating
inet6_dev{}, we do not need to call ipv6_find_idev() directly here.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes kernel bugzilla 10437
Based almost entirely upon a patch by Dmitry Butskoy.
When deciding what raw sockets to deliver the ICMPv6
to, we should use the addresses in the ICMPv6 quoted
IPV6 header, not the top-level one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Bolle wrote:
> http://bugzilla.kernel.org/show_bug.cgi?id=9923 would have been much easier to
> track down if eth_validate_addr() would somehow complain aloud if an address
> is invalid. Shouldn't it make at least some noise?
I guess it should return -EADDRNOTAVAIL similar to eth_mac_addr()
when validation fails.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet6_lookup family of functions requires a net to lookup
a socket in, so give a proper one to them.
No more things to do for dccpv6, since routing is OK and the
ipv4-like transport layer filtering is not done for ipv6.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to inet_ctl_sock_create to init callback (and
inet_ctl_sock_destroy to exit one) and use proper ctl sock
in dccp_v6_ctl_send_reset.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And replace all its usage with init_net's socket.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They will be responsible for ctl socket initialization, but
currently they are void.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This call uses the sock to get the net to lookup the routing
in. With CONFIG_NET_NS this code will OOPS, since the sk ptr
is NULL.
After looking inside the ip6_dst_lookup and drawing the analogy
with respective ipv6 code, it seems, that the dccp ctl socket
is a good candidate for the first argument.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables sockets creation with IPPROTO_DCCP and enables
the ip level to pass DCCP packets to the DCCP level.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet_lookup family of functions requires a net to lookup
a socket in, so give a proper one to them.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dccp_v4_route_skb used in dccp_v4_ctl_send_reset, currently
works with init_net's routing tables - fix it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to inet_ctl_sock_create to init callback (and
inet_ctl_sock_destroy to exit one) and use proper ctl sock
in dccp_v4_ctl_send_reset.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And replace all its usage with init_net's socket.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They will be responsible for ctl socket initialization, but
currently they are void.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace seq_open with seq_open_net and remove tcp_seq_release
completely. seq_release_net will do this job just fine.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to create seq_operations for each instance of 'netstat'.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_proc_register/tcp_proc_unregister are called with a static pointer only.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel-doc comment for skb_segment is clearly wrong. This states
what it actually does.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_reuse is declared as "unsigned char", but is set as type valbool in net/core/sock.c.
There is no other place in net/ where sk->sk_reuse is set to a value > 1, so the test
"sk_reuse > 1" can not be true.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies TIPC's socket code to use standard kernel
routines to handle time conversions between jiffies and ms.
This ensures proper operation even when HZ isn't 1000.
Acknowledgements to Eric Sesterhenn <snakebyte@gmx.de> for
identifying this issue and proposing a solution.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch eliminates re-initialization of the standard socket
wait queue used for sleeping in TIPC's socket creation code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfrm_get_policy() and xfrm_add_pol_expire() put some rather large structs
on the stack to work around the LSM API. This patch attempts to fix that
problem by changing the LSM API to require only the relevant "security"
pointers instead of the entire SPD entry; we do this for all of the
security_xfrm_policy*() functions to keep things consistent.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'asoc' parameter to sctp_cmd_hb_timer_update() is unused, and
we can remove it.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing (almost) all invocations of list_for_each() with
list_for_each_entry() tightens up the code and allows for the deletion
of numerous list iterator variables that are no longer necessary.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently I posted a patch to add some informational items to
/proc/net/sctp/assocs. All the information is correct, but because
of how the seqfile show operation is laid out, some of the formatting
is backwards. This patch corrects that formatting, so that the new
information appears at the end of each line, rather than in the middle.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All IP addresses that are present in a system are duplicated on
struct sctp_sockaddr_entry. They are linked in the global list
called sctp_local_addr_list. And this struct unions IPv4 and IPv6
addresses.
So, there can be rare case, when a sockaddr_in.sin_addr coincides
with the corresponding part of the sockaddr_in6 and the notifier
for IPv4 will carry away an IPv6 entry.
The fix is to check the family before comparing the addresses.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 3 warnings about discarding const qualifiers:
net/sctp/ulpevent.c:862: warning: passing argument 1 of 'sctp_event2skb' discards qualifiers from pointer target type
net/sctp/sm_statefuns.c:4393: warning: passing argument 1 of 'SCTP_ASOC' discards qualifiers from pointer target type
net/sctp/socket.c:5874: warning: passing argument 1 of 'cmsg_nxthdr' discards qualifiers from pointer target type
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an error length INIT-ACK during COOKIE-WAIT,
a 0-vtag ABORT will be responsed. This action violates the
protocol apparently. This patch achieves the following things.
1 If the INIT-ACK contains all the fixed parameters, use init-tag
recorded from INIT-ACK as vtag.
2 If the INIT-ACK doesn't contain all the fixed parameters,
just reflect its vtag.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4890 has the following text:
The HMAC algorithm based on SHA-1 MUST be supported and
included in the HMAC-ALGO parameter.
As a result, we need to check in sctp_verify_param() that HMAC_SHA1 is
present in the list. If not, we should probably treat this as a
protocol violation.
It should also be a protocol violation if the HMAC parameter is empty.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deleting of nonroot hnodes mostly doesn't work in u32_delete():
refcnt == 1 is expected, but such hnodes' refcnts are initialized
with 0 and charged only with "link" nodes. Now they'll start with
1 like usual. Thanks to Patrick McHardy for an improving suggestion.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit() and the other IP output functions expect to get a skb
with clear or properly initialized skb->cb. Unlike TCP and UDP, the
dccp_skb_cb doesn't contain a struct inet_skb_parm at the beginning,
so the DCCP-specific data is interpreted by the IP output functions.
This can cause false negatives for the conditional POST_ROUTING hook
invocation, making the packet bypass the hook.
Add a inet_skb_parm/inet6_skb_parm union to the beginning of
dccp_skb_cb to avoid clashes. Also add a BUILD_BUG_ON to make
sure it fits in the cb.
[ Combined with patch from Gerrit Renker to remove two now unnecessary
memsets of IPCB(skb)->opt ]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ax25_uid_free call walks the ax25_uid_list and releases entries
from it. The problem is that after the fisrt call to hlist_del_init
the hlist_for_each_entry (which hides behind the ax25_uid_for_each)
will consider the current position to be the last and will return.
Thus, the whole list will be left not freed.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a difference between IPv4 and IPv6 when sending packets
to the unspecified address (either 0.0.0.0 or ::) when using raw or
un-connected UDP sockets. There are two cases where IPv6 either fails
to send anything, or sends with the destination address set to ::. For
example:
--> ping -c1 0.0.0.0
PING 0.0.0.0 (127.0.0.1) 56(84) bytes of data.
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.032 ms
--> ping6 -c1 ::
PING ::(::) 56 data bytes
ping: sendmsg: Invalid argument
Doing a sendto("0.0.0.0") reveals:
10:55:01.495090 IP localhost.32780 > localhost.7639: UDP, length 100
Doing a sendto("::") reveals:
10:56:13.262478 IP6 fe80::217:8ff:fe7d:4718.32779 > ::.7639: UDP, length 100
If you issue a connect() first in the UDP case, it will be sent to ::1,
similar to what happens with TCP.
This restores the BSD-ism.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
- This patch adjusts IPv6 multicast routing module, net/ipv6/ip6mr.c,
to use mroute6 header definitions instead of mroute.
(MFC6_LINES instead of MFC_LINES, MAXMIFS instead of MAXVIFS, mifi_t
instead of vifi_t.)
- In addition, inclusion of some headers was removed as it is not needed.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Check length of setsockopt's optval, which provided by user, before copy it
from user space.
For POSIX compliant, return -EINVAL for setsockopt of short lengths.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
MIP6_OPT_PAD_X are actually for paddings in destination
option header. Replace them with our standard IPV6_TLV_PADX.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
* 'docs' of git://git.lwn.net/linux-2.6:
Add additional examples in Documentation/spinlocks.txt
Move sched-rt-group.txt to scheduler/
Documentation: move rpc-cache.txt to filesystems/
Documentation: move nfsroot.txt to filesystems/
Spell out behavior of atomic_dec_and_lock() in kerneldoc
Fix a typo in highres.txt
Fixes to the seq_file document
Fill out information on patch tags in SubmittingPatches
Add the seq_file documentation
Documentation/ is a little large, and filesystems/ seems an obvious
place for this file.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[NETNS][IPV6] tcp - assign the netns for timewait sockets
[IPV4]: Fix byte value boundary check in do_ip_getsockopt().
BNX2X: Correct bringing chip out of reset
[NETFILTER]: nf_nat: autoload IPv4 connection tracking
[NETFILTER]: xt_hashlimit: fix mask calculation
[XFRM]: xfrm_user: fix selector family initialization
rt61pci: rt61pci_beacon_update do not free skb twice
ssb-mipscore: Fix interrupt vectors
ssb-pcicore: Fix IRQ TPS flag handling
mac80211: use short_preamble mode from capability if ERP IE not present
[NET]: Undo code bloat in hot paths due to print_mac().
[TCP]: Don't allow FRTO to take place while MTU is being probed
[TCP]: tcp_simple_retransmit can cause S+L
[TCP]: Fix NewReno's fast rexmit/recovery problems with GSOed skb
[TCP]: Restore 2.6.24 mark_head_lost behavior for newreno/fack
nl80211: fix STA AID bug
b43legacy: fix bcm4303 crash
iwlwifi: fix n-band association problem
ipw2200: set MAC address on radiotap interface
libertas: fix mode initialization problem
| net/ipv6/ipv6_sockglue.c:162:16: warning: symbol 'net' shadows an earlier one
| net/ipv6/ipv6_sockglue.c:111:13: originally declared here
| net/ipv6/ipv6_sockglue.c:175:16: warning: symbol 'net' shadows an earlier one
| net/ipv6/ipv6_sockglue.c:111:13: originally declared here
| net/ipv6/ip6mr.c:1241:10: warning: symbol 'ret' shadows an earlier one
| net/ipv6/ip6mr.c:1163:6: originally declared here
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Copy the network namespace from the socket to the timewait socket.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison in ip_route_input is a hot path, by recoding the C
"and" as bit operations, fewer conditional branches get generated
so the code should be faster. Maybe someday Gcc will be smart
enough to do this?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unneeded test in the case where object to be freed
has to be a leaf. Don't need to use the generic tnode_free()
function, instead just setup leaf to be freed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The trie pointer is passed down to flush_list and flush_leaf
but never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the use of SACK and window scaling when syncookies are used
and the client supports tcp timestamps. Options are encoded into
the timestamp sent in the syn-ack and restored from the timestamp
echo when the ack is received.
Based on earlier work by Glenn Griffin.
This patch avoids increasing the size of structs by encoding TCP
options into the least significant bits of the timestamp and
by not using any 'timestamp offset'.
The downside is that the timestamp sent in the packet after the synack
will increase by several seconds.
changes since v1:
don't duplicate timestamp echo decoding function, put it into ipv4/syncookie.c
and have ipv6/syncookies.c use it.
Feedback from Glenn Griffin: fix line indented with spaces, kill redundant if ()
Reviewed-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vmalloc rather than alloc_pages to avoid wasting memory.
The problem is that tnode structure has a power of 2 sized array,
plus a header. So the current code wastes almost half the memory
allocated because it always needs the next bigger size to hold
that small header.
This is similar to an earlier patch by Eric, but instead of a list
and lock, I used a workqueue to handle the fact that vfree can't
be done in interrupt context.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we register the iucv bus after the infrastructure is ready,
userspace can start relying on it when it receives the uevent
for the bus.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This BUG_ON is not needed, since all (debug) checks are also done
in smp_call_function() which gets called by this function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SKF_ADF_NLATTR searches for a netlink attribute, which avoids manually
parsing and walking attributes. It takes the offset at which to start
searching in the 'A' register and the attribute type in the 'X' register
and returns the offset in the 'A' register. When the attribute is not
found it returns zero.
A top-level attribute can be located using a filter like this
(example for nfnetlink, using struct nfgenmsg):
...
{
/* A = offset of first attribute */
.code = BPF_LD | BPF_IMM,
.k = sizeof(struct nlmsghdr) + sizeof(struct nfgenmsg)
},
{
/* X = CTA_PROTOINFO */
.code = BPF_LDX | BPF_IMM,
.k = CTA_PROTOINFO,
},
{
/* A = netlink attribute offset */
.code = BPF_LD | BPF_B | BPF_ABS,
.k = SKF_AD_OFF + SKF_AD_NLATTR
},
{
/* Exit if not found */
.code = BPF_JMP | BPF_JEQ | BPF_K,
.k = 0,
.jt = <error>
},
...
A nested attribute below the CTA_PROTOINFO attribute would then
be parsed like this:
...
{
/* A += sizeof(struct nlattr) */
.code = BPF_ALU | BPF_ADD | BPF_K,
.k = sizeof(struct nlattr),
},
{
/* X = CTA_PROTOINFO_TCP */
.code = BPF_LDX | BPF_IMM,
.k = CTA_PROTOINFO_TCP,
},
{
/* A = netlink attribute offset */
.code = BPF_LD | BPF_B | BPF_ABS,
.k = SKF_AD_OFF + SKF_AD_NLATTR
},
...
The data of an attribute can be loaded into 'A' like this:
...
{
/* X = A (attribute offset) */
.code = BPF_MISC | BPF_TAX,
},
{
/* A = skb->data[X + k] */
.code = BPF_LD | BPF_B | BPF_IND,
.k = sizeof(struct nlattr),
},
...
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
