Here is a proposed Kconfig update for the new max6875 i2c chip driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After a careful code analysis on the new max6875 driver
(drivers/i2c/chips/max6875.c), I have come to the conclusion that this
driver may cause EEPROM corruptions if used on random systems.
The EEPROM part of the MAX6875 chip is accessed using rather uncommon
I2C sequences. What is seen by the MAX6875 as reads can be seen by a
standard EEPROM (24C02) as writes. If you check the detection method
used by the driver, you'll find that the first SMBus command it will
send on the bus is i2c_smbus_write_byte_data(client, 0x80, 0x40). For
the MAX6875 it makes an internal pointer point to a specific offset of
the EEPROM waiting for a subsequent read command, so it's not an actual
data write operation, but for a standard EEPROM, this instead means
writing value 0x40 to offset 0x80. Blame Philips and Intel for the
obscure protocol.
Since the MAX6875 and the standard, common 24C02 EEPROMs share two I2C
addresses (0x50 and 0x52), loading the max6875 driver on a system with
standard EEPROMs at either address will trigger a write on these
EEPROMs, which will lead to their corruption if they happen not to be
write protected. This kind of EEPROMs can be found on memory modules
(SPD), ethernet adapters (MAC address), laptops (proprietary data) and
displays (EDID/DDC). Most of these are hopefully write-protected, but
not all of them.
For this reason, I would recommend that the max6875 driver be
neutralized, in a way that nobody can corrupt his/her EEPROMs by just
loading the driver. This means either deleting the driver completely, or
not listing any default address for it. I'd like this to be done before
2.6.13-rc1 is released.
Additionally, the max6875 driver lacks the 24RF08 corruption preventer
present in the eeprom driver, which means that loading this driver in a
system with such a chip would corrupt it as well.
Here is a proposed quick patch addressing the issue, although I wouldn't
mind a complete removal if it makes everyone feel safer. I think Ben
has plans to replace this driver by a much simplified one anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a simple patch originally from Denis Vlasenko, which strips a
useless trailing whitespace from 8 strings in 4 i2c drivers. Please
apply, thanks.
From: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This includes various small cleanups and fixes to the TPS 6501x driver that
came mostly from review feedback by Jean Delvare; thanks Jean! Also some
goofy whitespace gets fixed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Wednesday 22 June 2005 08:17, Greg KH wrote:
> [PATCH] I2C: Coding style cleanups to via686a
>
> The via686a hardware monitoring driver has infamous coding style at the
> moment. I'd like to clean up the mess before I start working on other
> changes to this driver. Is the following patch acceptable? No code
> change, only coding style (indentation, alignments, trailing white
> space, a few parentheses and a typo).
>
> Signed-off-by: Jean Delvare <khali@linux-fr.org>
> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nice.
You missed some. This one is on top of your patch:
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lots of this patch is trivial code cleanups (static vars were being
intialized to 0, etc).
There's also some fixes for ISO transmits (max buffer handling).
Aswell, we have a few fixes to disable IRM capabilites correctly. We've
also disabled, by default some generally unused EXPORT symbols for the
sake of cleanliness in the kernel. However, instead of removing them
completely, we felt it necessary to have a config option that allowed
them to be enabled for the many projects outside of the main kernel tree
that use our API for driver development.
The primary reason for this patch is to revert a MODE6->MODE10 RBC
conversion patch from the SCSI maintainers. The new conversions handled
directly in the scsi layer do not seem to work for SBP2. This patch
reverts to our old working code so that users can enjoy using Firewire
disks and dvd drives again.
We are working with the SCSI maintainers to resolve this issue outside
of the main kernel tree. We'll merge the patch once the SCSI layer's
handling of the MODE10 conversion is working for us.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the target's split_io field when building a dm-mirror device so
incoming bios won't span the mirror's internal regions. Without this,
regions can be accessed while not holding correct locks and data corruption
is possible.
Reported-By: "Zhao Qian" <zhaoqian@aaastor.com>
From: Kevin Corry <kevcorry@us.ibm.com>
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is for supporting Epson s1d13xxx framebuffer device for m32r. #
Sorry, a little bigger.
The Epson s1d13806 is already supported by 2.6.12 kernel, and its driver is
placed as drivers/video/s1d13xxxfb.c.
For the m32r, a header file include/asm-m32r/s1d13806.h was prepared for
several m32r target platforms. It was originally generated by an Epson
tool S1D13806CFG.EXE, and modified manually for the m32r platforms.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a follow-up, we can allow the yenta-driver to be limited to PCMCIA
operation.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If probing for the correct interrupt fails on yenta bridges, the driver falls
back to polling for interrupt actions. However, CardBus cards cannot be used
then.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One correction is needed. Changes are not needed for
drivers/scsi/pcmcia/nsp_cs.c because it uses versioning in the
compatibility part, which is never used in 2.6 kernels. The only right
thing we could to that compatibility code would be to remove it throughout
the file, but that would be a separate patch.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Linux PCMCIA code has some data that was apparently used (or meant to be
used) to ensure that only proper client drivers are loaded. This is now
ensured (to a certain degree) by the fact that the most client drivers are
part of the kernel. Also, the version information has not been updated
despite major changes in PCMCIA API. This has made it meaningless.
This patch removes servinfo_t and pcmcia_get_card_services_info. They are not
used in any userspace utilities such as pcmcia-cs and pcmciautils.
drivers/pcmcia/pcmcia_ioctl.c is adjusted accordingly.
CS_RELEASE and CS_RELEASE_CODE are removed. include/pcmcia/version.h is empty
now. It will be removed later, but for now it's left in the tree to avoid
touching all PCMCIA clients.
The only driver that needs to be changed is drivers/scsi/pcmcia/nsp_cs.c,
which uses CS_RELEASE_CODE.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reduce the occurences of "client_handle_t" which is nothing else than a
pointer to struct pcmcia_device by now.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reduce the occurences of "client_handle_t" which is nothing else than a
pointer to struct pcmcia_device by now.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Schedule removal of the PCMCIA ioctl (and thus kernel support for the
pcmcia-cs userspace package) for November 2005.
A big "thank you" to Dave Hinds for his great work on supporting PCMCIA in
Linux. Things are just done differently by now, so the ongoing work to make
PCMCIA behave like any other hotpluggable bus should continue.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=f354942cb301fed273f423fb5c4f57bde3efc5b2
converted the check_region() calls in drivers/pcmcia/i82365.c into
request_regions. Unfortunately this seems to have broken things.
isa_probe() used to call check_region() and then call add_pcic() which would
request_region().
Now isa_probe() calls request_region() and then calls add_pcic() which calls
request_region() again, this fails and add_pcic() returns immediately without
doing all the setup etc.
On the face of it the patch below fixes the problem, by not doing the second
request region in add_pcic(). I think this is preferable to remove the call
in isa_probe() since identify() touches the I/O regions and is called before
add_pcic().
However I haven't fully grokked the meaning of the code which follows the
request_region() in isa_probe(), so I'm not sure that the handling WRT
multiple sockets and multiple bridge chips is correct. In particular I'm not
convinced that the regions for subsequent sockets and/or bridges will be
requested at all. I suspect a more thorough reworking by someone who
understands what is going on there might be in order.
I should mention that I'm actually messing about with this on an ARM platform
with wacky memory and i/o mapping offsets etc, it doesn't quite work yet for
other reasons which preclude full testing etc, but I think the problem above
is still present for more normal x86 stuff.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Correct sync byte for MPEG-2 transport stream packets.
- Add lgdt3302 as dependency of cx88-dvb in Kconfig.
- Add dvb support in v4l for DViCO FusionHDTV3 Gold-T using lgdt3302 frontend.
This adds support for a different board from the previous (Gold-Q) patch.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add dvb support in v4l for DViCO FusionHDTV3 Gold-Q using lgdt3302 frontend.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changed hue offset to 128 to correct behavior in cx88 cards. Previously,
setting 0% or 100% hue was required to avoid blue/green people on screen.
Now, 50% Hue means no offset, just like bt878 stuff.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add support for ADS Tech Instant TV DVB-T PCI.
- Remove obsoleted config options.
- Fix DViCO Board names
- Remove CABLE type setting from DViCO FusionHDTV3 Gold-T.
- Fix compilation with gcc4.0.
- V4L2_TUNER_CAP_LOW implemented according with V4L2 API for Radio.
- radio range is now defined on tuner-core.c. Cleaning up.
- Fix a bug on frequency report for cx88 based cards.
- Added support for changing radio mode stereo/mono.
- Add remove for MSI TV@nywhere.
Signed-off-by: Jorik Jonker <jorik@dnd.utwente.nl>.
Signed-off-by: Didier Caillaud <mailing.cld@free.fr>
Signed-off-by: Benoit Laniel <benoit.laniel@gmail.com>.
Signed-off-by: Nickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support and rewrote some parts with the help of vendor information
(Thanks to Steve Chang from WideView, Inc.):
o added support for the WT-220U (Pensize DVB-T receiver)
o corrected byte order for unc,ber and the pid filter
o corrected number of pids that can be fetched at the same time.
o added some comments in Kconfig-file
o added USB IDs for the WT-220U
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix tuning failure for 200103A, 200103A failed to tune to low band due to
wrong tone setting on the 200103A.
Signed-off-by: Steffen Motzer <motzersn@tlink.de>
Signed-off-by: Manu Abraham <manu@kromtek.com>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name-field of the pci_driver and usb_driver structs to the name of
the module after compilation. It seems that this field is used in some places
where special characters are not allowed. Thanks to Alan Halverson for
finding this problem.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for LGDT3302 (ATSC VSB/QAM) used in DViCO FusionHDTV3 Gold.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Timeout handling fixed, especially for preemtible kernels and/or high system
load.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't use HZ for usb-transfer-timeouts.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o add some remote control codes
o not using HZ for control_msg-timeout
Signed-off-by: Andrew Hodgson <a.s.hodgson@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o fixed usage of the correct number of events in keymapping-array
o better place for return
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct two keys of the vp7045 remote control key mapping.
Signed-off-by: Michael Paxton <packo@tpg.com.au>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Steve Chang reported the real name behind 0x14aa: WideView,
changed USB IDs accordingly.
o fixed an assignment
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o corrected some typos
o added the Wikilink pointing to the USB device list
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix memcpy copying into the wrong destination. Thanks to Allan Third for
reporting.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add another USB ID pair for the VideoWalker USB DVB-T.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was no pid-filter-count set for some devices - led to an error. Thanks
to Gerolf Wendland.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some more work on the digitv-usb driver:
o MT352 initialization and PLL-programming
o I2c-transfer fixed.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add dvb_pll_desc for ALPS TDED4 used in Nebula USB boxes. Changed the
name-field of the FMD1216.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add module parameter to deactive remote control polling.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add preliminary support for the Medion Hybrid USB2.0 DVB-T/Analogue box.
Analogue part is not working yet (cx25842 --> ivtv?).
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
