Fix this warning:
drivers/net/via-velocity.c:1924: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Signed-off-by: Seguier Regis <rseguier@e-teleport.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Dave Jones <davej@redhat.com>
The dma-debug changes caught that this driver uses the
wrong DMA mapping length when skb_padto() does something.
With suggestions from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
while(--j >= 0) keeps spinning when j is unsigned:
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a message bug in the via-velocity driver which
bothered me for some time.
The messages printed during device init look like the following:
[ 8.486422] eth%d: set value of parameter Wake On Lan options to 0
^^!
[ 8.487340] eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
Note the unresolved format string.
dev->name is unavailable before register_netdev, so use
dev_driver_string(&pdev->dev), which is also consistent with other
drivers.
"char *devname" parameters had to be converted to "const char *devname" to
be consistent with dev_driver_string return value.
Signed-off-by: Sven Hartge <sven@svenhartge.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the various different email addresses of mine listed in the code
to a single current and valid address. As Dave says his network merges
for 2.6.28 are now done this seems a good point to send them in where
they won't risk disrupting real changes.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and free everyting outside of the locked section.
Spotted-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Seguier Regis <rseguier@e-teleport.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
It should help people fix the bugs in my code :o)
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
It removes a dependancy from velocity_init_rd_ring to dev->mtu.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Updates of the RBRDU have two different meanings depending on their
context:
1. the receiving process has not started - the value which is written
into the RBRDU register is supposed to be the free rx descriptors
count (rounded to a multiple of 4)
2. the receiving process is running - the value increments the count
above (sic)
The update is currently issued deep inside the rx replenish chain (see
velocity_give_many_rx_descs).
Let's propagate enough information to the caller so that the rx
replenish functions do not depend on hardware any more.
It is needed to perform the Rx/Tx buffers housekeeping when MTU changes.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- PCI consistent areas need no memset
- use dev_err instead of plain printk
- avoid a few casts
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Executive summary: the bounce buffers are in my way
- they use something like a 64 * 1500 bytes area of PCI
consistent area
- they are not resized when the MTU changes
- they are used
- to hand-pad undersized packets. skb_pad anyone ?
- to linearize fragmented skbs whose fragment count
goes beyond the 7 fragments hardware limit in order
to claim scatter-gather support
Actually the SG code is commented out and I wonder if it
could not be implemented (ab-)using the large send feature
of the chipset since the latter should support some
multi-descriptor packet transmitting.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Séguier Régis <rseguier@e-teleport.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use memmove to handle overlapping copy of data.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev_alloc_skb for rx buffer allocation. This sets skb->dev
and can be overriden for NUMA machines.
Change code to return new buffer rather than call by reference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- vlans were using a single CAM register (see mac_set_vlan_cam)
- setting the address filtering registers for vlans is not
needed when there is no vlan
The non-tagged interface is filtered out as soon as a tagged
(!= 0) interface is created. Its traffic appears again when an
zero-tagged interface is created.
Tested on Via Epia SN (VT6130 chipset) with several vlans whose
tag was above or beyond 255.
Signed-off-by: Séguier Régis <rseguier@e-teleport.net>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
ip_fib_init is kept enabled. It is already namespace-aware.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a callback registered to inet address notifier chain.
The check is useless as:
- ifa is always != NULL
- similar checks are abscent in all other notifiers.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/via-velocity.c:443: error: chip_info_table causes a section type conflict
on this one I had to remove the __devinitdata too. Don't know why.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* kill bitfields
* annotate
* add missing conversions
* fix a couple of brainos in zerocopy stuff (fortunately, it's ifdef'ed out)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized. This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simple mtu change when device is down.
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9382.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Per Al's suggestion, get rid of the stupid stuff:
Remove cam_type switch,
And deinline things that aren't important for speed.
And make big macro and inline.
And remove some dead/unused code.
And use const char * for chip name.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The via-velocity is using a non-standard VLAN interface configured
via module parameters (yuck).
Replace with the standard acceleration interface.
It solves a number of problems with being able to handle multiple
vlans, and dynamically reconfigure.
This is compile tested only, don't have this board.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One patch for two trivial typos of 'error' with three R's, appearing in message strings.
There's a bunch more of the same in comments, not dealt with here.
Signed-off-by: Eddy L O Jansson <eddy@klopper.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
via-velocity doesn't build when CONFIG_INET=n:
drivers/built-in.o: In function `velocity_unregister_notifier':
via-velocity.c:(.text+0xe9b46): undefined reference to `unregister_inetaddr_notifier'
drivers/built-in.o: In function `velocity_init_module':
via-velocity.c:(.init.text+0xa027): undefined reference to `register_inetaddr_notifier'
I wanted to make this change in drivers/net/Kconfig, but
this isn't legal kconfig language:
config VIA_VELOCITY
tristate "VIA Velocity support"
depends on NET_PCI && PCI
+ depends on INET if PM
select CRC32
select CRC_CCITT
select MII
so fix it in via-velocity.c instead.
Builds with all 4 combinations of CONFIG_NET & CONFIG_PM.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch replaces bitreverse() by bitrev32. The only users of bitreverse()
are crc32 itself and via-velocity.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Replace CHECKSUM_HW by CHECKSUM_PARTIAL (for outgoing packets, whose
checksum still needs to be completed) and CHECKSUM_COMPLETE (for
incoming packets, device supplied full checksum).
Patch originally from Herbert Xu, updated by myself for 2.6.18-rc3.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I promised last week, here is the first pass at removing all
unnecessary printk's that exist in network device drivers currently in
promiscuous mode. The duplicate messages are not needed so they have
been removed. Some of these drivers are quite old and might not need an
update, but I did them all anyway.
I am currently auditing the remaining conditional printk's and will send
out a patch for those soon.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The via-velocity driver reports incorrect speed and link detected status
as viewed by ethtool (and probably other tools). This patch fixes those
incorrect reports and prettifies a long line.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
