This fixes a byte-swap issue on PPC, found by Zang Roy-r61911
on the powerpc platform. His original patch also had some other
platform-specific changes in #ifdef's, but I'm not sure yet how to
incorporate them. Look for another patch for those (soon).
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver currently keeps local copies of the hardware request/response queue indexes.
But it expends significant effort ensuring consistency between the two views,
and still gets it wrong after an error or reset occurs.
This patch removes the local copies, in favour of just accessing the hardware
whenever we need them. Eventually this may need to be tweaked again for NCQ,
but for now this works and solves problems some users were seeing.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 60xx chips, and possibly others, incorrectly assert DEV_IRQ interrupts
on a regular basis. The cause of this is under investigation (by me and
in theory by Marvell also), but regardless we do need to deal with these events.
This patch tidies up some interrupt handler code, and ensures that we ignore
DEV_IRQ interrupts when the drive still has ATA_BUSY asserted.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interface control register of the 60xx (and later) Marvell chip
requires certain bits to always be set when writing to it. These bits
incorrectly read-back as zeros, so the pattern must be ORed in
with each write of the register. Also, bit 12 should NOT be set
(note that Marvell's own driver also had bit-12 wrong here).
While we're at it, we also now do pci_set_master() in the init code.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some systems, it is possible that the BIOS may have enabled interrupt coalescing
for the Marvell controllers which support it. This patch adds code to detect/ack
interrupts from the chip's coalescing (combing) logic.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv_err_intr() function is invoked from the driver's interrupt handler,
as well as from the timeout function. This patch prevents it from triggering
a one-after-the-other double reset of the controller when invoked
from the timeout function.
This also adds a check for a timeout race condition that has been observed
to occur with this driver in earlier kernels. This should not be needed,
in theory, but in practice it has caught bugs. Maybe nuke it at a later date.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use new SCR and on/offline functions. Note that for LLDD which know
it implements SCR callbacks, SCR functions are guaranteed to succeed
and ata_port_online() == !ata_port_offline().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Currently it crashes when trying to dump the registers. This is an obvious
one-liner fix I suppose.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.
Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch renames ata_dev_present() to ata_dev_enabled() and adds
ata_dev_disabled(). This is to discern the state where a device is
present but disabled from not-present state. This disctinction is
necessary when configuring transfer mode because device selection
timing must not be violated even if a device fails to configure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(1) A DMA transfer size of 0x10000 was not being written
as 0x0000 in the PRDs. Fixed.
(1) The DEV_IRQ interrupt cause bit happens spuriously
during EDMA operation, and was not being ignored by the driver.
This led to various "drive busy" errors being reported,
with associated unpredictable behaviour. Fixed.
(2) If a SATA or PCI interrupt was received with no outstanding
command, the interrupt handler still attempted to invoke
ata_qc_complete(), triggering assert()/BUG_ON() behaviour
elsewhere in libata. Fixed.
The driver still has issues with confusion after error-recovery,
but should now be reliable in the absence of drive errors.
I will be looking more into the error-handling bugs next.
Signed-Off-By: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses a number of weird behaviours observed
for the sata_mv driver, by fixing an "off by one" bug in processing
of the EDMA response queue.
Basically, sata_mv was looking in the wrong place for
command results, and this produced a lot of unpredictable behaviour.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI midlayer has moved hostt->eh_timed_out to transport template. As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata. No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Interrupt handler did not properly initialize a variable on a per-port
basis, leading to incorrect behavior on ports other than port 0.
Bug caught and fixed by Mark Lord.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The previous dev->max_sectors patch made sht->max_sectors meaningless.
Kill all initializations of sht->max_sectors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch converts all assert(xxx)'s in low-level drivers to
WARN_ON(!xxx)'s. After this patch, there is no in-kernel user of the
libata assert() macro.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
->eng_timeout cannot be invoked with NULL qc anymore. Add an
assertion in ata_scsi_error() and kill NULL qc handling from all
->eng_timeout callbacks.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Several bug reports have come in, noting that disabling CONFIG_PCI_MSI
has fixed their problems with this driver. This may be generic system
issues, but there is also the probability of unimplemented hardware
errata workarounds. Until this ream of bug reports is sorted out, we
can get them going in non-MSI interrupt mode.
As such, this change adds an 'msi' module option, which defaults to off.
Implement ata_eh_qc_complete/retry() using scsi_eh_finish_cmd() and
scsi_eh_flush_done_q(). This removes all eh scsicmd finish hacks from
low level drivers.
This change was first suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add detailed AC_ERR_* flags and use them. Long-term goal is to
describe all errors with err_mask and tf combination (tf for failed
sector information, etc...). After proper error diagnosis is
implemented, sense data should also be generated from err_mask instead
of directly from hardware tf registers as it is currently.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
