For GRU and EPT, we need gup-fast to set referenced bit too (this is why
it's correct to return 0 when shadow_access_mask is zero, it requires
gup-fast to set the referenced bit). qemu-kvm access already sets the
young bit in the pte if it isn't zero-copy, if it's zero copy or a shadow
paging EPT minor fault we relay on gup-fast to signal the page is in
use...
We also need to check the young bits on the secondary pagetables for NPT
and not nested shadow mmu as the data may never get accessed again by the
primary pte.
Without this closer accuracy, we'd have to remove the heuristic that
avoids collapsing hugepages in hugepage virtual regions that have not even
a single subpage in use.
->test_young is full backwards compatible with GRU and other usages that
don't have young bits in pagetables set by the hardware and that should
nuke the secondary mmu mappings when ->clear_flush_young runs just like
EPT does.
Removing the heuristic that checks the young bit in
khugepaged/collapse_huge_page completely isn't so bad either probably but
I thought it was worth it and this makes it reliable.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should work for both hugetlbfs and transparent hugepages.
[akpm@linux-foundation.org: bring forward PageTransCompound() addition for bisectability]
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kvm-updates/2.6.38' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (142 commits)
KVM: Initialize fpu state in preemptible context
KVM: VMX: when entering real mode align segment base to 16 bytes
KVM: MMU: handle 'map_writable' in set_spte() function
KVM: MMU: audit: allow audit more guests at the same time
KVM: Fetch guest cr3 from hardware on demand
KVM: Replace reads of vcpu->arch.cr3 by an accessor
KVM: MMU: only write protect mappings at pagetable level
KVM: VMX: Correct asm constraint in vmcs_load()/vmcs_clear()
KVM: MMU: Initialize base_role for tdp mmus
KVM: VMX: Optimize atomic EFER load
KVM: VMX: Add definitions for more vm entry/exit control bits
KVM: SVM: copy instruction bytes from VMCB
KVM: SVM: implement enhanced INVLPG intercept
KVM: SVM: enhance mov DR intercept handler
KVM: SVM: enhance MOV CR intercept handler
KVM: SVM: add new SVM feature bit names
KVM: cleanup emulate_instruction
KVM: move complete_insn_gp() into x86.c
KVM: x86: fix CR8 handling
KVM guest: Fix kvm clock initialization when it's configured out
...
init_fpu() (which is indirectly called by the fpu switching code) assumes
it is in process context. Rather than makeing init_fpu() use an atomic
allocation, which can cause a task to be killed, make sure the fpu is
already initialized when we enter the run loop.
KVM-Stable-Tag.
Reported-and-tested-by: Kirill A. Shutemov <kas@openvz.org>
Acked-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Move the operation of 'writable' to set_spte() to clean up code
[avi: remove unneeded booleanification]
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It only allows to audit one guest in the system since:
- 'audit_point' is a glob variable
- mmu_audit_disable() is called in kvm_mmu_destroy(), so audit is disabled
after a guest exited
this patch fix those issues then allow to audit more guests at the same time
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of syncing the guest cr3 every exit, which is expensince on vmx
with ept enabled, sync it only on demand.
[sheng: fix incorrect cr3 seen by Windows XP]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If a pagetable contains a writeable large spte, all of its sptes will be
write protected, including non-leaf ones, leading to endless pagefaults.
Do not write protect pages above PT_PAGE_TABLE_LEVEL, as the spte fault
paths assume non-leaf sptes are writable.
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
'error' is byte sized, so use a byte register constraint.
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When NX is enabled on the host but not on the guest, we use the entry/exit
msr load facility, which is slow. Optimize it to use entry/exit efer load,
which is ~1200 cycles faster.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In case of a nested page fault or an intercepted #PF newer SVM
implementations provide a copy of the faulting instruction bytes
in the VMCB.
Use these bytes to feed the instruction emulator and avoid the costly
guest instruction fetch in this case.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When the DecodeAssist feature is available, the linear address
is provided in the VMCB on INVLPG intercepts. Use it directly to
avoid any decoding and emulation.
This is only useful for shadow paging, though.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Newer SVM implementations provide the GPR number in the VMCB, so
that the emulation path is no longer necesarry to handle debug
register access intercepts. Implement the handling in svm.c and
use it when the info is provided.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Newer SVM implementations provide the GPR number in the VMCB, so
that the emulation path is no longer necesarry to handle CR
register access intercepts. Implement the handling in svm.c and
use it when the info is provided.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
the recent APM Vol.2 and the recent AMD CPUID specification describe
new CPUID features bits for SVM. Name them here for later usage.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
emulate_instruction had many callers, but only one used all
parameters. One parameter was unused, another one is now
hidden by a wrapper function (required for a future addition
anyway), so most callers use now a shorter parameter list.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
move the complete_insn_gp() helper function out of the VMX part
into the generic x86 part to make it usable by SVM.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The handling of CR8 writes in KVM is currently somewhat cumbersome.
This patch makes it look like the other CR register handlers
and fixes a possible issue in VMX, where the RIP would be incremented
despite an injected #GP.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In KVM_CREATE_IRQCHIP, kvm_io_bus_unregister_dev() is called without taking
slots_lock in the error handling path.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
If KVM sees a read-only host page, it will map it as read-only to prevent
breaking a COW. However, if the page was part of a large guest page, KVM
incorrectly extends the write protection to the entire large page frame
instead of limiting it to the normal host page.
This results in the instantiation of a new shadow page with read-only access.
If this happens for a MOVS instruction that moves memory between two normal
pages, within a single large page frame, and mapped within the guest as a
large page, and if, in addition, the source operand is not writeable in the
host (perhaps due to KSM), then KVM will instantiate a read-only direct
shadow page, instantiate an spte for the source operand, then instantiate
a new read/write direct shadow page and instantiate an spte for the
destination operand. Since these two sptes are in different shadow pages,
MOVS will never see them at the same time and the guest will not make
progress.
Fix by mapping the direct shadow page read/write, and only marking the
host page read-only.
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the xsetbv intercept to the AMD part
of KVM. This makes AVX usable in a save way for the guest on
AVX capable AMD hardware.
The patch is tested by using AVX in the guest and host in
parallel and checking for data corruption. I also used the
KVM xsave unit-tests and they all pass.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Large page information has two elements but one of them, write_count, alone
is accessed by a helper function.
This patch replaces this helper function with more generic one which returns
newly named kvm_lpage_info structure and use it to access the other element
rmap_pde.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
In certain use-cases, we want to allocate guests fixed time slices where idle
guest cycles leave the machine idling. There are many approaches to achieve
this but the most direct is to simply avoid trapping the HLT instruction which
lets the guest directly execute the instruction putting the processor to sleep.
Introduce this as a module-level option for kvm-vmx.ko since if you do this
for one guest, you probably want to do it for all.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the new flush-by-asid of upcoming AMD
processors to the KVM-AMD module.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch replaces all calls to force_new_asid which are
intended to flush the guest-tlb by the more appropriate
function svm_flush_tlb. As a side-effect the force_new_asid
function is removed.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function is unused and there is svm_flush_tlb which
does the same. So this function can be removed.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Retry #PF for softmmu only when the current vcpu has the same cr3 as the time
when #PF occurs
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Retry #PF is the speculative path, so don't set the accessed bit
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It's the speculative path if 'no_apf = 1' and we will specially handle this
speculative path in the later patch, so 'prefault' is better to fit the sense.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for all LBR related
state. This includes the debugctl, br_from, br_to,
last_excp_from, and last_excp_to msrs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the cr2 register in
the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit defined for the cs, ds,
ss, an es segemnts and the current cpl saved in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the base and limit
of the gdt and idt in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the dr6 and dr7
debug registers in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the CRx clean-bit for the vmcb. This
bit covers cr0, cr3, cr4, and efer.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for all nested paging
related state in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for all interrupt
related state in the vmcb. This corresponds to vmcb offset
0x60-0x67.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the asid in the
vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the clean bit for the physical addresses of
the MSRPM and the IOPM. It does not need to be set in the
code because the only place where these values are changed
is the nested-svm vmrun and vmexit path. These functions
already mark the complete VMCB as dirty.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the clean-bit for intercepts-vectors, the
TSC offset and the pause-filter count to the appropriate
places. The IO and MSR permission bitmaps are not subject to
this bit.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the infrastructure for the implementation of
the individual clean-bits.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
One more "KVM: MMU: Don't drop accessed bit while updating an spte."
Sptes are accessed by both kvm and hardware.
This patch uses update_spte() to fix the way of removing write access.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
If we execute VMREAD during reboot we'll just skip over it. Instead of
returning garbage, return 0, which has a much smaller chance of confusing
the code. Otherwise we risk a flood of debug printk()s which block the
reboot process if a serial console or netconsole is enabled.
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch replaces the open-coded vmcb-selection for the
TSC calculation with the new get_host_vmcb helper function
introduced in this patchset.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch wraps changes to the misc intercepts of SVM
into seperate functions to abstract nested-svm better and
prepare the implementation of the vmcb-clean-bits feature.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
