Fix broken BD processing code.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix two issues in this driver's netpoll path: one usual, with spin_unlock_irq()
enabling interrupts which nobody asks it to do (that has been fixed recently in
a number of drivers) and one unusual, with poll_controller() method possibly
causing loss of interrupts due to the interrupt status register being cleared
by a simple read and the interrpupt handler simply storing it, not accumulating.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface. If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).
This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover. This insures that switches are kept up to date
for all cases.
"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch. His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ARP validation code only needs ARPs for the bonding device.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bonding can erroneously register the same packet_type to receive
ARPs (for use by ARP validation): once at device open time, and once via
sysfs. Since sysfs can change the validate setting (and thus register
or unregister) at any time, a flag is needed to synchronize with device
open in order to avoid double registrations, and the simplest place is
within the packet_type structure itself. Double unregister is not an
issue.
Bug reported by Ulrich Oelmann <ulrich.oelmann@web.de>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix wrong "port" calculations in pdc202xx_{configure_piomode,set_dmamode}()
They were broken for all configurations except one (master device on primary
channel, no other devices) and as a result device settings + PIO/DMA timings
were being programmed into the wrong PCI registers. This could result in
a large variety of problems including data corruption, hangs etc. (depending
on devices used and your luck :-).
ap->port_no ap->devno used PCI registers correct PCI registers
0 0 0x60-0x62 0x60-0x62
0 1 0x62-0x64 0x64-0x66
1 0 0x64-0x66 0x68-0x6a
1 1 0x66-0x68 0x6c-0x6e
Also forward port recent fixes from drivers/ide pdc202xx_old driver:
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
and finally bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_legacy fails to detect the disk on my old ISA/VLB 486:
it starts to probe io=0x1f0 ctr=0x3f6 irq=15, complains
loudly about IDENTIFYs timing out, and finally fails.
(Sorry I couldn't capture the kernel's boot messages.)
It turns out that the driver's mapping from io to irq in
legacy_irq[] is wrong: index 0 for io=0x1f0 has irq=15 but
should have irq=14, and index 1 for io=0x170 has irq=14 but
should have irq=15. This is confirmed by a comparison with
include/asm-i386/ide.h:ide_default_irq().
This patch swaps the first two elements in legacy_irq[],
which makes pata_legacy work on my 486.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the Intel ICH9M RAID controller DID for SATA support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The subchannel may just be status pending, even with actl == 0. We
must go through the cancel_halt_clear procedure to put the subchannel
into a defined state.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After I/O has been killed by the common I/O layer, trigger path
verification which will queue cio_device_nopath_notify itself if it
finds a device to be without paths.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure we hold the device lock when we modify the ccw device
structure but always call the notify function without the lock held.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For extended error reporting we sometimes have to start an
Sense Subsystem Status request (SNSS). When this request needs
to be recovered for some reason, the recovery request will
fail with 'command reject'.
Our usual recovery procedure will retry the failed request by
creating a new request and chaining the failed request from that
one. SNSS requests, though, must not be chained from anything,
so the recovery request will fail permanently.
Use the default recovery for SNSS request, which will just restart
the original request without further ado.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After switching compression on/off with the mt command, tape encryption is no
longer working. The reason for that is, that the modeset_byte is set to
the compression value instead of using bitwise and/or bit operations to
enable/disable the corresponding bit.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I recognized a compile error in latest git:
/here/workdir/git/drivers/net/gianfar.c: In function `gfar_vlan_rx_kill_vid':
/here/workdir/git/drivers/net/gianfar.c:1135: error: structure has no member named `vgrp'
This error was introduced in commit:
commit 6d04e3b04b
...
[VLAN]: Avoid a 4-order allocation.
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CT based mach64 cards were reported to hang on sparc64 boxes when
compiled with gcc-4.1.x and later.
Looking at this piece of code, it's no surprise. A critical
delay was implemented as an empty for() loop, and gcc 4.0.x
and previous did not optimize it away, so we did get a delay.
But gcc-4.1.x and later can optimize it away, and we get crashes.
Use a real udelay() to fix this. Fix verified on SunBlade100.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replacing use of UTS_RELEASE with utsname()->release avoids that the
usb-storage driver is recompiled each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"drivers/char/epca.c:2741: warning: 'get_termio' defined but not used"
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipmi_si_intf tries to access default ports, if no device could be found
elsewhere. On PPC we have a function to check, if these legacy IO ports
are accessible. This patch adds a check for these ports on PPC. This
patch fixes a breakage of IPMI module on PPC machines without a BMC.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent patch for raid6 reshape had a change missing that showed up in
subsequent review.
Many places in the raid5 code used "conf->raid_disks-1" to mean "number of
data disks". With raid6 that had to be changed to "conf->raid_disk -
conf->max_degraded" or similar. One place was missed.
This bug means that if a raid6 reshape were aborted in the middle the
recorded position would be wrong. On restart it would either fail (as the
position wasn't on an appropriate boundary) or would leave a section of the
array unreshaped, causing data corruption.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently sm501fb_crtsrc_store() won't allow the routing to be changed via
echos from userspace in to the sysfs file. The reason for this is that the
strnicmp() for both heads uses a sizeof() for the string length, which ends
up being strlen() + 1 (\0 in the normal case, but the echo gives a newline,
which is where the issue occurs), this then causes a mismatch and
subsequently bails with the -EINVAL.
In addition to this, the hardcoded lengths were then used for the store
length that was returned, which ended up being erroneous and resulting in a
write error. There's also no point in returning anything but the full
length since it will -EINVAL out on a mismatch well before then anyways.
sizeof("string") is great for making sure you have space in your buffer,
but rather less so for string comparisons :-)
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove remaining references to saved registers now that
uart_handle_sysrq_char() does not want them.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpio_keys driver is wrongly ARM-specific; it can't build on
other platforms with GPIO suport. This fixes that problem.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix soft lockup with iSeries viocd driver, caused by eventually calling
end_that_request_first() with nr_bytes 0.
Some versions of hald do an SG_IO ioctl on the viocd device which becomes a
request with hard_nr_sectors and hard_cur_sectors set to zero. Passing zero
as the number of sectors to end_request() (which calls
end_that_request_first()) causes an infinite loop when the bio is being freed.
This patch makes sure that the zero is never passed. It only requires some
number larger the the request size the terminate the loop.
The lockup is triggered by hald, interrogating the device.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For devices that do not support msi-x we only support 1 interrupt. Therefore
we can disable that one interrupt by disabling the msi capability itself. If
we leave the intx interrupts disabled while we have the msi capability
disabled no interrupts should be delivered from that device.
Devices with just the minimal msi support (and thus hitting this code path)
include things like the intel e1000 nic, so it looks like is going to be a
fairly common case and thus important to get right.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
enable/disable_msi_mode have several side effects which keeps them from being
generally useful. So this patch replaces them with with two much more
targeted functions: msi_set_enable and msix_set_enable.
This patch makes pci_dev->msi_enabled and pci_dev->msix_enabled the definitive
way to test if linux has enabled the msi capability, and has the appropriate
msi data structures set up.
This patch ensures that while writing the msi messages in save/restore and
during device initialization we have the msi capability disabled so we don't
get into races. The pci spec requires that we do not have the msi capability
enabled and the msi messages unmasked while we write the messages. Completely
disabling the capability is overkill but it is easy :)
Care has been taken so we never have both a msi capability and intx enabled
simultaneously. We haven't run into a problem yet but better safe then sorry.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In http://bugzilla.kernel.org/show_bug.cgi?id=8065, Shen points out that the
cyclades driver forget to return closing_wait to userspace.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Shen <shanlu@cs.uiuc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enabling the backlight by default appears to cause problems for many
users. This patch disables backlight controls unless explicitly
enabled by users via a module parameter. Since PMAC users are known
to work, default to enabled in that case.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Fix a mix up when the nvidia driver was converted resulting
in the backlight having an incorrect initial brightness.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[VLAN]: Avoid a 4-order allocation.
[HDLC] Fix dev->header_cache_update having a random value.
[NetLabel]: Verify sensitivity level has a valid CIPSO mapping
[PPPOE]: Key connections properly on local device.
[AF_UNIX]: Test against sk_max_ack_backlog properly.
[NET]: Fix bugs in "Whether sock accept queue is full" checking
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] Acorn: move the i2c bus driver into drivers/i2c
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
[ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
[ARM] rtc-pcf8583: correct month and year offsets
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
[ARM] EBSA110: Work around build errors
[ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
[ARM] 4239/1: S3C24XX: Update kconfig entries for PM
[ARM] 4238/1: S3C24XX: docs: update suspend and resume
[ARM] 4237/2: oprofile: Always allow backtraces on ARM
[ARM] Yet more asm/apm-emulation.h stuff
ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
ARM: OMAP: Use linux/delay.h not asm/delay.h
ARM: OMAP: Remove obsolete alsa typedefs
ARM: OMAP: omap1510->15xx conversions needed for sx1
ARM: OMAP: Add missing includes to board-nokia770
ARM: OMAP: Workqueue changes for board-h4.c
ARM: OMAP: dmtimer.c omap1 register fix
ARM: OMAP: board-nokia770: correct lcd name
...
Move the Acorn IOC/IOMD I2C bus driver from drivers/i2c, strip
out the reminants of the platform specific parts of the old
PCF8583 RTC code, and remove the old obsolete PCF8583 driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An off-by-one bug meant we were always trying to map one too many
scatterlist entries. This was mostly harmless prior to the checks
going in to consistent_sync(), but now causes the kernel to BUG.
Also, powertec.c was missing an assignment to info->ec.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI doesn't want drivers to modify request_bufflen, so keep a
driver-private copy of this in the scsi_pointer structure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the I2C bus address, as per drivers/acorn/char/pcf8583.c.
Also, since this driver also contains Acorn RiscPC specific code
for obtaining the current year from the SRAM (and updating the
platform specific checksum when writing new data back) this is
NOT a platform independent driver.
Document it as such, and update the dependencies to reflect this
fact.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both BCD_TO_BIN(x) and BIN_TO_BCD(x) have an unexpected side-effect -
not only do they return the value as expected, they _modify_ their
argument in the process.
Let's play it safe and avoid these macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the standard magic.h for kvmfs.
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A bogus 'return r' can cause an otherwise successful module load to fail.
This both denies users the use of kvm, and it also denies them the use of
their machine, as it leaves a filesystem registered with its callbacks
pointing into now-freed module memory.
Fix by returning a zero like a good module.
Thanks to Richard Lucassen <mailinglists@lucassen.org> (?) for reporting
the problem and for providing access to a machine which exhibited it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Enabling dirty page logging is done using KVM_SET_MEMORY_REGION ioctl.
If the memory region already exists, we need to remove write accesses,
so writes will be caught, and dirty pages will be logged.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Since dirty_bitmap is an unsigned long array, the alignment and size need
to take that into account.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A few places where we modify guest memory fail to call mark_page_dirty(),
causing live migration to fail. This adds the missing calls.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Allocate a distinct inode for every vcpu in a VM. This has the following
benefits:
- the filp cachelines are no longer bounced when f_count is incremented on
every ioctl()
- the API and internal code are distinctly clearer; for example, on the
KVM_GET_REGS ioctl, there is no need to copy the vcpu number from
userspace and then copy the registers back; the vcpu identity is derived
from the fd used to make the call
Right now the performance benefits are completely theoretical since (a) we
don't support more than one vcpu per VM and (b) virtualization hardware
inefficiencies completely everwhelm any cacheline bouncing effects. But
both of these will change, and we need to prepare the API today.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This reflects the changed scope, from device-wide to single vm (previously
every device open created a virtual machine).
Signed-off-by: Avi Kivity <avi@qumranet.com>
This avoids having filp->f_op and the corresponding inode->i_fop different,
which is a little unorthodox.
The ioctl list is split into two: global kvm ioctls and per-vm ioctls. A new
ioctl, KVM_CREATE_VM, is used to create VMs and return the VM fd.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The kvmfs inodes will represent virtual machines and vcpus, as necessary,
reducing cacheline bouncing due to inodes and filps being shared.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the SVM code to intercept SMIs and handle it
outside the guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This adds a special MSR based hypercall API to KVM. This is to be
used by paravirtual kernels and virtual drivers.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Besides using an established api, this allows using kvm in older kernels.
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The whole thing is rotten, but this allows vmx to boot with the guest reboot
fix.
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We fail to mark a page dirty in three cases:
- setting the accessed bit in a pte
- setting the dirty bit in a pte
- emulating a write into a pagetable
This fix adds the missing cases.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Legacy IDE VLB host drivers didn't check for "probe" options when compiled
as modules, which was obviously wrong as we don't want module to poke at
random I/O ports by simply loading it. Fix it by adding "probe" module param
to legacy IDE VLB host drivers.
v2:
* don't obsolete old "ide0=dtc2278/ht6560b/qd65xx/ali14xx/umc8672"
IDE driver options yet (per Alan Cox's request) and enhance documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove
* "hdx=serialize"
* "idex=noautotune"
* "idex=autotune"
kernel params, they have been obsoleted for ages.
"idex=serialize", "hdx=noautotune" and "hdx=autotune" are still available
so there is no funcionality loss caused by this patch.
v2:
* fix CONFIG_BLK_DEV_4DRIVES=y build broken by version 1 of the patch
[ /me wearing brown paper bag ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 27 February 2007, Akira Iguchi wrote:
>
> But since I sent the first patch, I found a bug for checking DMA IRQ status.
> (http://www.spinics.net/lists/linux-ide/msg06903.html)
> Then I sent the fixed patch for libata only. So my drivers/ide patch
> still has same bug and I want to fix it, too.
>
> The following patch fixes this bug. Please apply this patch.
From: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Revised DRAC4 warning as Jeff suggested, this one includes more info
about why the problem occurs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The change to force legacy mode IDE channels' resources to fixed non-zero
values confuses (at least some versions of) X, because the values reported
by the kernel and those readable from PCI config space aren't consistent
anymore. Therefore, this patch arranges for the respective BARs to also
get updated if possible.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix breakage added in the IDE devel tree.
Add header, then fix
drivers/ide/ppc/pmac.c: In function `pmac_ide_setup_dma':
drivers/ide/ppc/pmac.c:2044: warning: assignment from incompatible pointer type
drivers/ide/ppc/pmac.c: In function `pmac_ide_dma_host_on':
drivers/ide/ppc/pmac.c:1989: warning: control reaches end of non-void function
include/linux/pci.h: In function `pmac_ide_init':
drivers/ide/ppc/pmac.c:1563: warning: ignoring return value of `pci_register_driver', declared with attribute warn_unused_result
Then add some apparently-long-missing error handling.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add CFA devices from I-O Data, Mitsubishi and Viking. Add SanDisk comment.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The tuneproc() method in both these drivers failed to set the drive's own speed.
Fix this by renaming the function and "wrapping around it" the new tuneproc()
method. Switch back to calling tuneproc() in the PIO fallback code.
While at it, also convert the rest of the PIO timing code into proper C. :-)
Has been kind of tested on SLC90E66. I'm too lazy to reboot my box and test
on ICH4... :-)
[ bart: I quickly tested it on ICH4. ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
eighty_ninty_three() had word 93 validitity check but not the 80c bit
test itself (bit 13). This increases the chance of incorrect wire
detection especially because host side cable detection is often
unreliable and we sometimes soley depend on drive side cable
detection. Fix it.
[ bart: fix off-by-1 bit name in the patch description ]
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to cmd64x_tune_pio(), making it return the mode set,
and "wrapping" the new tuneproc() method around it; while at it, also get rid
of the non-working prefetch control code (filtering out related argument values
in the "wrapper"), remove redundant PIO5 mode limitation, make cmdprintk() give
more sensible mode info, and remove mention about the obsolete /proc/ interface.
Get rid of the broken config_chipset_for_pio() which always tried to set PIO4,
switch to always auto-tuning PIO instead.
Oh, and add the missing PIO5 support to the speedproc() method while at it. :-)
Warning: compile tested only -- getting to the real hardware isn't that easy...
On Tuesday 06 February 2007 22:11, Mikael Pettersson <mikpe@it.uu.se> wrote:
>
> Worked fine on my SPARC Ultra5 with a CMD646 IDE controller.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to ali15x3_tune_pio() and "wrapping" the new tuneproc()
method around it and making it return the mode set, update the heading comment.
Also, setting PIO mode via the speedproc() method does not work due to passing
to the tuneproc() method's a mode number not biased by XFER_PIO_0 -- fix this
along with a typo in the heading comment...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This updates the cx88-blackbird driver to be able to use the new cx23416
firmware image released by Hauppauge Computer Works, while retaining
compatibility with the older firmware images.
cx2341x firmware can be downloaded at: http://dl.ivtvdriver.org/ivtv/firmware/
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching HDLC devices from Ethernet-framing mode caused stale ethernet
function assignments within net_device.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is based on the assumption that an interface's ifindex is basically
an alias for a local MAC address, so incoming packets now are matched
to sockets based on remote MAC, session id, and ifindex of the
interface the packet came in on/the socket was bound to by connect().
For relayed packets, the socket that's used for relaying is selected
based on destination MAC, session ID and the interface index of the
interface whose name currently matches the name requested by userspace
as the relaying source interface.
Signed-off-by: David S. Miller <davem@davemloft.net>
The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 908b637fe7 removed ETH_DMA_ALIGN
but missed a usage of it in a macro, which broke the build.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This missing line caused transmit errors on the Qlogic 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix copyright and license ("regents" should not have ever been used).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to stop tc35815 before resetting the board. This fixes the
build of tc35815 as a module. This also means there is no caller of
tc35815_killall left, so remove that function also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conditionalize all PM related stuff in libata core layer using
CONFIG_PM.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some LLDs were missing scsi device PM callbacks while having host/port
suspend support. Add missing ones.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you'll recall, over a year ago, I pointed out that the current
Radeon driver erroneously returns -EINVAL for valid blanking codes,
here is a link to that thread:
http://lkml.org/lkml/2006/1/28/6
No other driver does this, and it confuses the X server into thinking
that the device does not support blanking properly.
I looked again and there is simply no reason for the Radeon driver to
return -EINVAL for FB_BLANK_NORMAL. It claims it wants to do this in
order to convince fbcon to blank in software, right here:
if (fb_blank(info, blank))
fbcon_generic_blank(vc, info, blank);
to software blank the screen. But it only causes that to happen
in the FB_BLANK_NORMAL case.
That makes no sense because the Radeon code does this:
val |= CRTC_DISPLAY_DIS;
in the FB_BLANK_NORMAL case so should be blanking the hardware, and
there is therefore no reason to SW blank by returning -EINVAL.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Antonino Daplas <adaplas@gmail.com>
The QDI init code contains some bugs which mean it only works if you have
a test setup that causes both a successful and failed probe. Fix this
Found by Philip Guo
(Who found it working on code analysis tools not running VLB IDE
controllers)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox noticed several hooks in pata_* drivers were missing, when
he authored his ->cable_detect hook patches. This patch extracts
just those fixes from Alan's patches, adding the necessary hooks
(usually ->freeze, ->thaw, and ->post_internal_cmd) to the drivers.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2.6.21-rc has horrible problems with libata and PATA cable types (and
thus speeds). This occurs because Tejun fixed a pile of other bugs and
we now do cable detect enforcement for drive side detection properly.
Unfortunately we don't do the process around cable detection right. Tejun
identified the problem and pointed to the right Annex in the spec, this patch
implements the needed changes.
The basic requirement is that we have to identify the slave before the
master.
The patch switches the identify order so that we can do the drive side
detection correctly.
[NOTE: patch and description extracted from a larger work written
and signed-off-by Alan Cox]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The initial simplex handling code is fooled if you suspend and resume.
This also causes problems with some single channel controllers which
claim to be simplex.
The fix is fairly simple, instead of keeping a flag to remember if we
gave away the simplex channel we remember the actual owner. As the owner
is always part of the host_set we don't even need a refcount.
Knowing the owner also means we can reassign simplex DMA channels in
future hotplug code etc if we need to
Signed-off-by: Alan Cox <alan@redhat.com>
(and a signed-off for the patch I sent before while I remember)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Put all Code Mercenaries (VID 0x07c0) IOWarriors (PIDs 0x1500 to 0x15ff) on
the HID blacklist. The range of PIDs has been reserved for IOWarriors. Only
5 PIDs are really used yet.
Signed-off-by: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: improve spurious SDB FIS handling
ahci/pata_jmicron: match class not function number
jmicron ATA: reimplement jmicron ATA quirk
pata_jmicron: drop unnecessary device programming in [re]init
libata: blacklist FUJITSU MHT2060BH for NCQ
sata_sil24: kill unused local variable idx in sil24_fill_sg()
libata: clear drvdata in ata_host_release(), take#2
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: fix Logitech DiNovo Edge touchwheel and Logic3 /SpectraVideo middle button
HID: add git tree information to MAINTAINERS
HID: fix broken Logitech S510 keyboard report descriptor; make extra keys work
HID: fix possible double-free on error path in hid parser
HID: hid-debug.c should #include <linux/hid-debug.h>
HID: fix bug in zeroing the last field byte in output reports
USB HID: use CONFIG_HID_DEBUG for outputting report descriptor
USB HID: Fix USB vendor and product IDs endianness for USB HID devices
Spurious SDB FIS during NCQ might not contain spurious completions.
It could be spurious TF update or invalid async notification. Treat
as HSM violation iff a spurious SDB FIS contains spurious completions;
otherwise, just whine once about it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make jmiron_ata quirk update pdev->class after programming the device
and update ahci and pata_jmicron such that they match class code
instead of checking function number manually. For ahci, it matches
for vendor and class. For pata_jmicron, it matches vendor, device and
class as IDE class isn't as well defined as AHCI class.
This makes jmicron device matching more conventional and script
friendly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement jmicron ATA quirk.
* renamed to quirk_jmicron_ata()
* quirk is invoked only for the affected controllers
* programming is stricter. e.g. conf5 bit24 is cleared if
unnecessary.
* code factored for readability
* JMB360 and JMB368 are programmed into proper mode
Verified on JMB360, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Channel redirect and AHCI mode enable programmings are done via PCI
quirk for both probe and resume paths. Drop duplicate and possibly
unsafe device programming from pata_jmicron().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Blacklist FUJITSU MHT2060BH for NCQ. On this drive, NCQ works iff
queue depth is equal to or less than 4. Just turn it off.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mike Accetta <maccetta@laurelnetworks.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill unused local variable idx in sil24_fill_sg().
Spotted by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clearing drvdata in ->remove_one causes NULL pointer deference. Clear
drvdata only in ata_host_release() after all resources are freed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a possible race that leads to double freeing an idr index.
When the master begin to close, release_dev() is called and then
pty_close() is called:
if (tty->driver->close)
tty->driver->close(tty, filp);
This is done without helding any locks other than BKL. Inside pty_close(),
being a master close, the devpts entry will be removed:
#ifdef CONFIG_UNIX98_PTYS
if (tty->driver == ptm_driver)
devpts_pty_kill(tty->index);
#endif
But devpts_pty_kill() will call get_node() that may sleep while waiting for
&devpts_root->d_inode->i_sem. When this happens and the slave is being
opened, tty_open() just found the driver and index:
driver = get_tty_driver(device, &index);
if (!driver) {
mutex_unlock(&tty_mutex);
return -ENODEV;
}
This part of the code is already protected under tty_mute. The problem is
that the slave close already got an index. Then init_dev() is called and
blocks waiting for the same &devpts_root->d_inode->i_sem.
When the master close resumes, it removes the devpts entry, and the
relation between idr index and the tty is gone. The master then sleeps
waiting for the tty_mutex on release_dev().
Slave open resumes and found no tty for that index. As result, a NULL tty
is returned and init_dev() doesn't flow to fast_track:
/* check whether we're reopening an existing tty */
if (driver->flags & TTY_DRIVER_DEVPTS_MEM) {
tty = devpts_get_tty(idx);
if (tty && driver->subtype == PTY_TYPE_MASTER)
tty = tty->link;
} else {
tty = driver->ttys[idx];
}
if (tty) goto fast_track;
The result of this, is that a new tty will be created and init_dev() returns
sucessfull. After returning, tty_mutex is dropped and master close may resume.
Master close finds it's the only use and both sides are closing, then releases
the tty and the index. At this point, the idr index is free, but slave still
has it.
Slave open then calls pty_open() and finds that tty->link->count is 0,
because there's no master and returns error. Then tty_open() calls
release_dev() which executes without any warning, as it was a case of last
slave close when the master is already closed (master->count == 0,
slave->count == 1). The tty is then released with the already released idr
index.
This normally would only issue a warning on idr_remove() but in case of a
customer's critical application, it's never too simple:
thread1: opens master, gets index X
thread1: begin closing master
thread2: begin opening slave with index X
thread1: finishes closing master, index X released
thread3: opens master, gets index X, just released
thread2: fails opening slave, releases index X <----
thread4: opens master, gets index X, init_dev() then find an already in use
and healthy tty and fails
If no more indexes are released, ptmx_open() will keep failing, as the
first free index available is X, and it will make init_dev() fail because
you're trying to "reopen a master" which isn't valid.
The patch notices when this race happens and make init_dev() fail
imediately. The init_dev() function is called with tty_mutex held, so it's
safe to continue with tty till the end of function because release_dev()
won't make any further changes without grabbing the tty_mutex.
Without the patch, on some machines it's possible get easily idr warnings
like this one:
idr_remove called for id=15 which is not allocated.
[<c02555b9>] idr_remove+0x139/0x170
[<c02a1b62>] release_mem+0x182/0x230
[<c02a28e7>] release_dev+0x4b7/0x700
[<c02a0ea7>] tty_ldisc_enable+0x27/0x30
[<c02a1e64>] init_dev+0x254/0x580
[<c02a0d64>] check_tty_count+0x14/0xb0
[<c02a4f05>] tty_open+0x1c5/0x340
[<c02a4d40>] tty_open+0x0/0x340
[<c017388f>] chrdev_open+0xaf/0x180
[<c017c2ac>] open_namei+0x8c/0x760
[<c01737e0>] chrdev_open+0x0/0x180
[<c0167bc9>] __dentry_open+0xc9/0x210
[<c0167e2c>] do_filp_open+0x5c/0x70
[<c0167a91>] get_unused_fd+0x61/0xd0
[<c0167e93>] do_sys_open+0x53/0x100
[<c0167f97>] sys_open+0x27/0x30
[<c010303b>] syscall_call+0x7/0xb
using this test application available on:
http://www.ruivo.org/~aris/pty_sodomizer.c
Signed-off-by: Aristeu Sergio Rozanski Filho <aris@ruivo.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CAPI trace debug functions were using a fixed size buffer, which can be
overflowed if wrong formatted CAPI messages were sent to the kernel capi
layer. The code was also not protected against multiple callers. This fix
bug 8028.
Additionally the patch make the CAPI trace functions optional.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3: Introduce CONFIG_PS3_ADVANCED, as suggested by Roman Zippel, and use
it to control questions about PS3 subsystems that may not be obvious for
the casual user.
This gets rid of the following warning on non-powerpc platforms: |
drivers/video/Kconfig:1604:warning: 'select' used by config symbol 'FB_PS3'
refer to undefined symbol 'PS3_PS3AV'
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the bay driver depends on the dock driver for proper notification,
make this driver depend on the dock driver.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) Remove #define acrobatics that have become unnecessary by the move of
asyncdata.o into the common part.
b) Correct the rule for building the common part into the kernel when
some or all hardware specific parts are built as modules.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an oops on the rtc_device_unregister() path by waiting until the last
moment before nulling the rtc->ops vector. Fix some potential oopses by
having the rtc_class_open()/rtc_class_close() interface increase the RTC's
reference count while an RTC handle is available outside the RTC framework.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.e. one or more drives can be added and the array will re-stripe
while on-line.
Most of the interesting work was already done for raid5. This just extends it
to raid6.
mdadm newer than 2.6 is needed for complete safety, however any version of
mdadm which support raid5 reshape will do a good enough job in almost all
cases (an 'echo repair > /sys/block/mdX/md/sync_action' is recommended after a
reshape that was aborted and had to be restarted with an such a version of
mdadm).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An error always aborts any resync/recovery/reshape on the understanding that
it will immediately be restarted if that still makes sense. However a reshape
currently doesn't get restarted. With this patch it does.
To avoid restarting when it is not possible to do work, we call into the
personality to check that a reshape is ok, and strengthen raid5_check_reshape
to fail if there are too many failed devices.
We also break some code out into a separate function: remove_and_add_spares as
the indent level for that code was getting crazy.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mddev and queue might be used for another array which does not set these,
so they need to be cleared.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
md tries to warn the user if they e.g. create a raid1 using two partitions of
the same device, as this does not provide true redundancy.
However it also warns if a raid0 is created like this, and there is nothing
wrong with that.
At the place where the warning is currently printer, we don't necessarily know
what level the array will be, so move the warning from the point where the
device is added to the point where the array is started.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use kernel_fpu_begin() and kernel_fpu_end()
- Use boot_cpu_has() for feature testing even in userspace
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two errors that can lead to recovery problems with raid10
when used in 'far' more (not the default).
Due to a '>' instead of '>=' the wrong block is located which would result in
garbage being written to some random location, quite possible outside the
range of the device, causing the newly reconstructed device to fail.
The device size calculation had some rounding errors (it didn't round when it
should) and so recovery would go a few blocks too far which would again cause
a write to a random block address and probably a device error.
The code for working with device sizes was fairly confused and spread out, so
this has been tided up a bit.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If register_blkdev() or alloc-disk fail in mm_init() after
pci_register_driver() succeeds, then mm_pci_driver is not unregistered
properly:
Cc: Philip Guo <pg@cs.stanford.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move VIDIOC_DBG_S/G_REGISTER from the internal ioctl list to the
public ioctls, but mark it as experimental for now.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for starting, stopping, pausing and resuming an MPEG (or similar
compressed stream) encoder.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VIDIOC_G_ENC_INDEX ioctl can obtain the MPEG index from an MPEG
encoder.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without this patch, the device will not be detected after firmware download
on big endian systems.
Signed-off-by: Jin-Bong lee <jinbong.lee@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following warning:
drivers/media/video/cafe_ccic.c: In function `cafe_vidioc_reqbufs':
drivers/media/video/cafe_ccic.c:1197: warning: 'ret' might be used uninitialized in this function
Probably not a real bug, but the warning can be avoided easily.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb-pll normally opens the i2c gate before attempting to communicate with
the pll, but the code for this device is not using dvb-pll. This should
be cleaned up in the future, but for now, just open the i2c gate at the
appropriate place in order to fix this driver bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The chip matching in struct v4l2_register for VIDIOC_DBG_G/S_REGISTER
was rather primitive. It could not be extended to other busses besides
i2c and it lacked a way to.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to changes in the i2c handling in 2.6.20 this cx25840 bug surfaced,
causing the firmware load to fail for the ivtv driver. The correct
sequence is to first attach the i2c client, then use the client's
device to load the firmware.
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Dongle shipped with Logitech DiNovo Edge (0x046d/0xc714) behaves in a weird
non-standard way - it contains multiple reports with the same usage, which
results in remapping of GenericDesktop.X and GenericDesktop.Y usages to
GenericDesktop.Z and GenericDesktop.RX respectively, thus rendering the
touchwheel unusable.
The commit 3506897691 solved this
in a way that it didn't remap certain usages. This however breaks
(at least) middle button of Logic3 / SpectraVideo (0x1267/0x0210),
which in contrary requires the remapping.
To make both of the harware work, allow remapping of these usages again,
and introduce a quirk for Logitech DiNovo Edge "touchwheel" instead - we
disable remapping for key, abs and rel events only for this hardware.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes extra keys (F1-F12 in special mode, zooming, rotate, shuffle)
on Logitech S510 keyboard work.
Logitech S510 keyboard sends in report no. 3 keys which are far above the
logical maximum described in descriptor for given report.
This patch introduces a HID quirk for this wireless USB receiver/keyboard
in order to fix the report descriptor before it's being parsed - the logical
maximum and the number of usages is bumped up to 0x104d). The values are in the
"Reserved" area of consumer HUT, so HID_MAX_USAGE had to be changed too.
In addition to proper extracting of the values from report descriptor, proper
HID-input mapping is introduced for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Freeing of device->collection is properly done in hid_free_device() (as
this function is supposed to free all the device resources and could be
called from transport specific code, e.g. usb_hid_configure()).
Remove all kfree() calls preceeding the hid_free_device() call.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Every file should include the headers containing the prototypes for
it's global functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
d4ae650a90 introduced zeroing of the
last field byte in output reports in order to make sure the unused
bits are set to 0. This is done in a wrong way, resulting in a
wrong bits being zeroed out (not properly shifted by the field offset
in the report). Fix this.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report descriptor should be output when CONFIG_HID_DEBUG is defined.
This also mitigates the need for DEBUG and DEBUG_DATA defines, so let's
remove them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB vendor and product IDs are not byteswapped appropriately, and
thus come out in the wrong endianness when fetched through the evdev
using ioctl() on big endian platforms.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
