This is the fix for the following problem:
https://bugzilla.redhat.com/show_bug.cgi?id=227657
The bnx2 device 5706 complains about MSI not working behind a
ServerWorks HT1000 PCIX bridge. An earlier commit to fix the problem:
e3008dedff:
"PCI: disable MSI by default on systems with Serverworks HT1000 chips"
was not entirely correct, and has been reverted.
MSI does not work on the PCIX bus because the BIOS did not set the
HT_MSI_FLAGS_ENABLE bit in the HyperTransport MSI capability on the
bridge. We use the existing quirk_msi_ht_cap() to detect the problem
and disable MSI in all buses behind it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Anantha Subramanyam <ananth@broadcom.com>
Cc: Naren Sankar <nsankar@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit e3008dedff.
The real bug was an INTX issue in the tg3 ethernet chip, and
cured by commit c129d962a66c76964954a98b38586ada82cf9381
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set bits 0, 4, 5 and 7 of PCI configuration register 0x40 in the
quirk. This has the following effects and is recommended by the
vendor.
* Force enable of IDE channels (used to be left alone as BIOS
configured)
* Change initial phase behavior of PIO cycle such that the host pulls
down the bus instead of tristating it. Vendor recommends this
setting.
The above settings are better for the current generation of
controllers and needed for the upcoming next generation.
Tested on JMB363.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On the "MSI K8T Neo2-FIR" board the BIOS disables the onboard
soundcard, if a second PCI soundcard is present.
This patch sets the korrect register bit to enable the onboard sound.
Removed old code in /drivers/pci/quirks.c that only checks for the
PCI-ID and fires on any Board with VIA 8237.
New code in /arch/i386/pci/fixup.c checks the DMI-tables and only runs
on the specific board.
Signed-off-by: Johannes Goecke <goecke@upb.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linas reported me that some machines were crashing at boot in
quirk_e100_interrupt. It appears that this quirk is doing an ioremap
directly on a PCI BAR value, which isn't legal and will cause all sorts
of bad things to happen on architectures where PCI BARs don't directly
match processor bus addresses.
This fixes it by using the proper PCI resources instead which is possible
since the quirk has been moved by a previous commit to happen late enough
for that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI quirk to unhide SMBus on Compaq Deskpro EP 401963-001 (PCA# 010174) motherboard.
Signed-off-by: Greg White <gw.kernel@tnode.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The k8t_sound_hostbridge PCI quick fires on my motherboard (Jetway
K8M8MS) while it shouldn't: the on-board sound chip is not disabled
and is working just fine. Looking at the code, I see that we are
running the quirk for two distinct register values (0x88 and 0xc8)
and then clear bit 6 (0x40). However value 0x88 already has bit 6
cleared so this is a no-op. This is what happens on my board. Thus I
believe that the quirk should only be run for register value 0xc8.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RS690 can't do MSI like its predecessors. Disable MSI on RS690.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Henry Su <henry.su@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
quirk_e100_interrupts() is called after PCI controller is initialized
and before PCI bus enumeration is performed. On some powerpc platforms
which modify PCI controller configuration and set different MEM and IO
windows than those set by firmware quirk_e100_interrupt() is causing
kernel panic as it tries to read from device BAR0 offets which at this
time points to a invalid PCI window (set by firmware).
This patch delays the quirk_100_interrupt() to pci_fixup_final phase,
which happens after bus enumeration and before PCI enable and
device driver initialization.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces an interface to read and write PCI-X / PCI-Express
maximum read byte count values from PCI config space. There is a second
function that returns the maximum _designed_ read byte count, which marks the
maximum value for a device, since some drivers try to set MMRBC to the
highest allowed value and rely on such a function.
Based on patch set by Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Peter Oruba <peter.oruba@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Via VT3351 APIC does not play well with MSI and unleashes a flood
of APIC errors when MSI is used to deliver interrupts. The problem
was recently exposed when the atl1 network device driver, which enables
MSI by default, stimulated APIC errors on an Asus M2V mainboard, which
employs the Via VT3351.
See http://bugzilla.kernel.org/show_bug.cgi?id=8472 for additional
details on this bug.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been seeing lots of messages like these:
eth0: No interrupt was generated using MSI, switching to INTx mode. Please
report this failure to the PCI maintainer and include system chipset
information.
On several systems that use the following Severworks HT1000 (also sometimes
labeled as a Broadcom chipset as well) bridge chips. It doesn't appear MSI
works well (if at all) on these systems.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit c0affe9db4 doesn't work because
the host controller is being quirked not a PCI bridge. This patch
reverts the commit, rename quirk_svw_msi() to quirk_disable_all_msi()
and use it instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matias Alejandro Torres <torresmat@gmail.com>
Cc: Greg K-H <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Besides those modes in ATI SB600 SATA controller, ATI SB700 supports one
more mode:the combined mode.
The combined mode is a Legacy IDE mode used for compatibility with some old
OS without AHCI driver, but now it is not necessary for Linux since the
kernel has supported AHCI.
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.
This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.
For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.
In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was found that the Toshiba laptops with hidden Intel SMBus have SMM
code handling the thermal management which accesses the SMBus. Thus it
is not safe to unhide it and let Linux access it. We have to leave the
SMBus hidden. SMM is a pain, really.
This fixes bugs #6315 and #6395, for good this time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make jmiron_ata quirk update pdev->class after programming the device
and update ahci and pata_jmicron such that they match class code
instead of checking function number manually. For ahci, it matches
for vendor and class. For pata_jmicron, it matches vendor, device and
class as IDE class isn't as well defined as AHCI class.
This makes jmicron device matching more conventional and script
friendly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement jmicron ATA quirk.
* renamed to quirk_jmicron_ata()
* quirk is invoked only for the affected controllers
* programming is stricter. e.g. conf5 bit24 is cleared if
unnecessary.
* code factored for readability
* JMB360 and JMB368 are programmed into proper mode
Verified on JMB360, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I don't see any reason why we need pci_msi_quirk, quirk code can just
call pci_no_msi() instead.
Remove the check of pci_msi_quirk in msi_init(). This is safe as all
calls to msi_init() are protected by calls to pci_msi_supported(),
which checks pci_msi_enable, which is disabled by pci_no_msi().
The pci_disable_msi routines didn't check pci_msi_quirk, only
pci_msi_enable, but as far as I can see that was a bug not a feature.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since 2.6.0-test10, all quirk_sis_96x_compatible() had any effect on
was a printk().
This patch therefore removes it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Speed up the Intel SMBus PCI quirk by avoiding tests which can only
fail. This also makes the compiled code significantly smaller when
using gcc 3.2/3.4. gcc 4.x appears to optimize the code by itself so
this change doesn't make a difference there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's an existing quirk for the kernel to use 1k IO space granularity
on the Intel P64H2. It turns out however that pci_setup_bridge() in
drivers/pci/setup-bus.c reads in the IO base and limit address register
masks it off to the nearest 4k, and writes it back. This causes the
kernel to be on 1k boundaries and the hardware to be 4k aligned. The
patch below fixes the problem.
Signed-off-by: Dan Yeisley <dan.yeisley@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following cleanups:
- move all EXPORT_SYMBOL's directly below the code they are exporting
- move all DECLARE_PCI_FIXUP_*'s directly below the functions they
are calling
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the driver for the Toshiba TC86C001 GOKU-S PCI IDE controller,
completely reworked from the original brain-damaged Toshiba's 2.4 version.
This single channel UltraDMA/66 controller is very simple in programming,
yet Toshiba managed to plant many interesting bugs in it. The particularly
nasty "limitation 5" (as they call the errata) caused me to abuse the IDE
core in a possibly most interesting way so far. However, this is still
better than the #ifdef mess in drivers/ide/ide-io.c that the original
version included (well, it had much more mess)...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set. This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.
The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits. If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.
This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add special handling for the VT82C686.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix VIA quirks that were recently broken by Alan Cox in the upstream
kernel (commit 1597cacbe3).
My understanding is that pci_find_present() doesn't work yet at the time
the quirks are run. So I used a two-step quirk as is done for some other
quirks already. First we detect the VIA south bridges and set the right
low and high device limits, then we are ready to actually run the quirks on
the affected devices.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unhide the SMBus on the Asus P4P800-X (and probably some other
models of the family.) This gives access to the memory module SPD
EEPROMs.
Thanks to Winbond for supporting the lm-sensors project with the
donation of this motherboard.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o MODPOST generates warnings for i386 if kernel is compiled with
CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc_ich6' (at offset 0xc0217d58) and 'quirk_cardbus_legacy'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc' (at offset 0xc0217fd9) and 'pci_match_id'
o Two quirk functions which are non __init, are accessing data which is
of type __init.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The sis96x SMBus PCI device depends on two different quirks to run
in a specific order. Apart from being fragile, this was found to
actually break on (at least) recent FC4, FC5, and FC6 kernels. This
patch fixes the quirks so that they work without relying on the
compiler and/or linker to put them in any specific order.
http://lists.lm-sensors.org/pipermail/lm-sensors/2006-April/015962.htmlhttps://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=189719
I tested this patch.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Greg K-H <greg@kroah.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pci_get_slot() may return NULL if nothing was found. quirk_nvidia_ck804()
does not check the value returned from pci_get_slot(), so it may end up
causing a NULL pointer deref.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is designed to fix:
- Disk eating corruptor on KT7 after resume from RAM
- VIA IRQ handling
- VIA fixups for bus lockups after resume from RAM
The core of this is to add a table of resume fixups run at resume time.
We need to do this for a variety of boards and features, but particularly
we need to do this to get various critical VIA fixups done on resume.
The second part of the problem is to handle VIA IRQ number rules which
are a bit odd and need special handling for PIC interrupts. Various
patches broke various boxes and while this one may not be perfect
(hopefully it is) it ensures the workaround is applied to the right
devices only.
From: Jean Delvare <khali@linux-fr.org>
Now that PCI quirks are replayed on software resume, we can safely
re-enable the Asus SMBus unhiding quirk even when software suspend support
is enabled.
[akpm@osdl.org: fix const warning]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use pci_find_ht_capability() in drivers/pci/quirks.c.
I'm pretty sure the logic is unchanged here, but someone please eye-ball it
for me. I've changed the message to be a little shorter, it's now:
PCI: Found (enabled|disabled) HT MSI mapping on xxxx:xx:xx.x
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes redundant check for dev->subordinate; if it is NULL, the function
returns before the patch-affected code region.
Signed-off-by: David Rientjes <rientjes@cs.washington.edu>
Acked-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number of permutations of crap we do is amazing and almost all of it
has the wrong effect in 2.6.
At the heart of this is the PCI SFF magic which says that compatibility
mode PCI IDE controllers use ISA IRQ routing and hard coded addresses
not the BAR values. The old quirks variously clears them, sets them,
adjusts them and then IDE ignores the result.
In order to drive all this garbage out and to do it portably we need to
handle the SFF rules directly and properly. Because we know the device
BAR 0-3 are not used in compatibility mode we load them with the values
that are implied (and indeed which many controllers actually
thoughtfully put there in this mode anyway).
This removes special cases in the IDE layer and libata which now knows
that bar 0/1/2/3 always contain the correct address. It means our
resource allocation map is accurate from boot, not "mostly accurate"
after ide is loaded, and it shoots lots of code. There is also lots more
code and magic constant knowledge to shoot once this is in and settled.
Been in my test tree for a while both with drivers/ide and with libata.
Wants some -mm shakedown in case I've missed something dumb or there are
corner cases lurking.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=7264
We need to target this quirk a little more tightly, using the T20 DMI string.
Cc: Pavel Kysilka <goldenfish@bsys.cz>
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My K8T800 mobo resumes fine from suspend to ram with and without patch
applied against 2.6.18.
quirk_via_abnormal_poweroff makes some boards not boot 2.6.18, so IMO patch
should go to head, 2.6.18.2 and everywhere "ACPI: ACPICA 20060623" has been
applied.
Remove quirk_via_abnormal_poweroff
Obsoleted by "ACPI: ACPICA 20060623":
<snip>
Implemented support for "ignored" bits in the ACPI
registers. According to the ACPI specification, these
bits should be preserved when writing the registers via
a read/modify/write cycle. There are 3 bits preserved
in this manner: PM1_CONTROL[0] (SCI_EN), PM1_CONTROL[9],
and PM1_STATUS[11].
http://bugzilla.kernel.org/show_bug.cgi?id=3691
</snip>
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: Bob Moore <robert.moore@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts much of the original pci_fixup_video change and makes it
work for all arches that need it.
fixed, and tested on x86, x86_64 and IA64 dig.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit 4e8a520150 ("[PKT_SCHED] netem:
Orphan SKB when adding to queue.") Davem mistakenly also included a
temporary diff in his tree that disabled the pci_fixup_video VGA quirk,
which broke sparc64.
This reverts that part of the commit. Sayeth Davem:
"Greg KH has a patch coming to you soon which will move that VGA code
back into x86/x86_64/IA64 specific areas and will fix the sparc64
problem properly."
Special thanks to Claudio Martins <ctpm@ist.utl.pt> for noticing the
error in the first place.
Cc: Claudio Martins <ctpm@ist.utl.pt>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>