Due to an erratum, we don't want to reset the mpic at boot time. It can
sometimes cause problems with lost interrupts later on while running.
Signed-off-by: Olof Johansson <olof@lixom.net>
Driver for the CompactFlash slot on the PA Semi Electra eval board. It's
a simple device sitting on localbus, with interrupts and detect/voltage
control over GPIO.
The driver is implemented as an of_platform driver, and adds localbus
as a bus being probed by the of_platform framework.
[akpm@linux-foundation.org: cleanups]
[olof@lixom.net: fix build]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Milton Miller <miltonm@bga.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move pasemi_idle_init() to be a late_initcall instead of being called from
setup_arch(). This way the cpufreq driver has a chance to initialize and
save away the boot time astate before we go to idle for the first time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add printout of some SoC error status registers, and dump the SLB contents
for those machine check events where it makes sense.
Since we can't go about and ioremap registers at machine check time,
and we generally want to do as little as possible to print out the
information, pre-build a table of the registers to dump and their address
in the common PCI config space range.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework timebase handoff to play nice with configurations with more than
2 cores, as well as with CPU hotplug.
Previous scheme just pushed out the current timebase from the giving
core to all cores without caring if they wanted it or not, nor checking
if they'd taken it. The taking side didn't make sure the giving side
had provided a value yet either. In other words, it was completely broken.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the pasemi platform to "pasemi" to be in line with the
platform's directory name.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
[netdrvr] atl1: fix build
pasemi_mac: Use local-mac-address instead of mac-address if available
pasemi_mac: PHY support
pasemi_mac: Add msglevel support and "debug" module param
pasemi_mac: Logic cleanup / rx performance improvements
pasemi_mac: Minor cleanup / define fixes
pasemi_mac: Add SKB reuse / copy-break
pasemi_mac: Timer and interrupt fixes
pasemi_mac: Abstract and fix up interrupt restart routines
pasemi_mac: Move the IRQ mapping from the PCI layer to the driver
tc35815: Remove unnecessary skb->dev assignment
drivers/net/dm9000: Convert to generic boolean
AT91RM9200 Ethernet: Fix multicast addressing
AT91RM9200 Ethernet: Support additional PHYs
PCMCIA-NETDEV : xirc2ps_cs: bugfix of multicast code
sky2: re-enable 88E8056 for most motherboards
MIPS: Drop unnecessary CONFIG_ISA from RBTX49XX
ne: MIPS: Use platform_driver for ne on RBTX49XX
ne: Add NEEDS_PORTLIST to control ISA auto-probe
ne: Misc fixes for platform driver.
...
Fix conflict in drivers/net/pasemi_mac.c (get_property() got renamed to
of_get_property()) manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes for ethernet IRQ mapping, to be done in the driver instead of in
the platform setup code.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only publish of_platform devices if running on a machine that has them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/setup.c: In function 'pasemi_publish_devices':
arch/powerpc/platforms/pasemi/setup.c:220: warning: implicit declaration of function 'of_platform_bus_probe'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MDIO driver for PHY's connected via GPIO as on the PA Semi Electra
eval board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reset MPIC on boot to clear some timer state that firmware might
leave configured.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The DMA controller on PWRficient is somewhat special -- has a PCI header
so it looks like it's on the root PCI (-Express) root bus, but it uses
more than the default number of interrupts (and they are hardwired).
We need to wire up all interrupts for the DMA controller. The generic
IRQ code will only map the primary interrupt from the PCI header (128),
so add 129->211 by hand.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Timebase update is simple on PA6T, since global updates can be done from
one core by writing to an SPR.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement reset on platforms/pasemi. Default is just to reset the
cpu using the SDC registers.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powersave support on PA6T. Right now it only uses 'doze' mode, and
will default to no savings (spin).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow more than the default 256 MPIC sources. Allocates a new flag
(MPIC_LARGE_VECTORS) to be used by platform code when instantiating
the mpic.
I picked 11 bits worth right now since it would cover the number of
sources on any hardware I have seen. It can always be increased later
if needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The (maple|pasemi)_init_IRQ functions call of_node_put(root) once more
than they should, causing the refcount of the root node to underflow,
which triggers the WARN_ON in kref_get.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.
Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
