Some aspects of PHY initialization are board dependent, things like
indicator LED connections and some clocking modes cannot be determined
by probing. The dev_flags element of struct phy_device can be used to
control these things if an appropriate value can be passed from the
Ethernet driver. We run into problems however if the PHY connections
are specified by the device tree. There is no way for the Ethernet
driver to know what flags it should pass.
If we are using the device tree, the struct phy_device will be
populated with the device tree node corresponding to the PHY, and we
can extract extra configuration information from there.
The next question is what should the format of that information be?
It is highly device specific, and the device tree representation
should not be tied to any arbitrary kernel defined constants. A
straight forward representation is just to specify the exact bits that
should be set using the "marvell,reg-init" property:
phy5: ethernet-phy@5 {
reg = <5>;
compatible = "marvell,88e1149r";
marvell,reg-init =
/* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */
<3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */
/* mix %:0, led[0123]:drive low off hiZ */
<3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */
/* default blink periods. */
<3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */
/* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */
<3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */
};
phy6: ethernet-phy@6 {
reg = <6>;
compatible = "marvell,88e1118";
marvell,reg-init =
/* Fix rx and tx clock transition timing */
<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
/* Adjust LED drive. */
<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
/* irq, blink-activity, blink-link */
<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
};
The Marvell PHYs have a page select register at register 22 (0x16), we
can specify any register by its page and register number. These are
the first and second word. The third word contains a mask to be ANDed
with the existing register value, and the fourth word is ORed with the
result to yield the new register value. The new marvell_of_reg_init
function leaves the page select register unchanged, so a call to it
can be dropped into the .config_init functions without unduly
affecting the state of the PHY.
If CONFIG_OF_MDIO is not set, there is no of_node, or no
"marvell,reg-init" property, the PHY initialization is unchanged.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1149R is 10/100/1000 quad-gigabit Ethernet PHY. The
.config_aneg function can be shared with 88E1118, but it needs its own
.config_init.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of the Marvell PHY page register is not specific to
88E1121, so rename the macro to MII_MARVELL_PHY_PAGE, and use it
throughout.
Suggested-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver appears to be mistaking the permission field with default value
in the case of debug and qlge_irq_type.
Driver is also passing debug as a bitmask into netif_msg_init()
which wants a number of bits. Ron Mercer suggests we should
change this to pass in -1 so the defaults get used instead,
which makes the default much less verbose.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ref count bug introduced by
commit 2de7957072
Author: Lorenzo Colitti <lorenzo@google.com>
Date: Wed Oct 27 18:16:49 2010 +0000
ipv6: addrconf: don't remove address state on ifdown if the address
is being kept
Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .stack section doesn't contain any contents, and doesn't require
initialization either. Rather than marking the output section with
'NOLOAD' but still having it exist in the object files, mark it with
%nobits which avoids the assembler marking the section with 'CONTENTS'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ALC887-VD is like ALC888-VD. It can not be initialized as ALC882.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit c0763e687d
ALSA: snd-atmel-abdac: test wrong variable
the return value via PTR_ERR() had to be fixed as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/677652
The original reporter states that, in 2.6.35, headphones do not appear
to work, nor does inserting them mute the A52J's onboard speakers. Upon
inspecting the codec dump, it appears that the newly committed hp-laptop
quirk will suffice to enable this basic functionality. Testing was done
with an alsa-driver build from 2010-11-21.
Reported-and-tested-by: Joan Creus
Cc: <stable@kernel.org> [2.6.35+]
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After clk_get() pclk is checked second time instead of sample_clk check.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
. Fix PulseAudio "ALSA driver bug" issue
(if we have two alternated areas within a 64k DMA buffer, then max
period size should obviously be 32k only).
Back references:
http://pulseaudio.org/wiki/AlsaIssueshttp://fedoraproject.org/wiki/Features/GlitchFreeAudio
. In stop timer function, need to supply ACK in the timer control byte.
. Minor log output correction
When I did my first PA testing recently, the period size bug resulted
in quite precisely observeable half-period-based playback distortion.
PA-based operation is quite a bit more underrun-prone (despite its
zero-copy optimizations etc.) than raw ALSA with this rather spartan
sound hardware implementation on my puny Athlon.
Note that even with this patch, azt3328 still doesn't work for both
cases yet, PA tsched=0 and tsched
(on tsched=0 it will playback tiny fragments of periods, leading to tiny
stuttering sounds with some pauses in between, whereas with
timer-scheduled operation playback works fine - minus some quite increased
underrun trouble on PA vs. ALSA, that is).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/677830
The original reporter states that the subwoofer does not mute when
inserting headphones. We need an entry for his machine's SSID in the
subwoofer pin fixup list, so add it there (verified using hda_analyzer).
Reported-and-tested-by: i-NoD
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/669279
The original reporter states: "The Master mixer does not change the
volume from the headphone output (which is affected by the headphone
mixer). Instead it only seems to control the on-board speaker volume.
This confuses PulseAudio greatly as the Master channel is merged into
the volume mix."
Fix this symptom by applying the hp_only quirk for the reporter's SSID.
The fix is applicable to all stable kernels.
Reported-and-tested-by: Ben Gamari <bgamari@gmail.com>
Cc: <stable@kernel.org> [2.6.32+]
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 8b592783 added a Thumb-2 variant of usracc which, when it is
called with \rept=2, calls usraccoff once with an offset of 0 and
secondly with a hard-coded offset of 4 in order to avoid incrementing
the pointer again. If \inc != 4 then we will store the data to the wrong
offset from \ptr. Luckily, the only caller that passes \rept=2 to this
function is __clear_user so we haven't been actively corrupting user data.
This patch fixes usracc to pass \inc instead of #4 to usraccoff
when it is called a second time.
Cc: <stable@kernel.org>
Reported-by: Tony Thompson <tony.thompson@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation of sched_clock() for the Nomadik
family is based on the clock source that will wrap around without
any compensation. Currently on the Ux500 after 1030 seconds.
Utilize cnt32_to_63 to expand the sched_clock() counter to 63
bits and introduce a keepwarm() timer to assure that sched clock
and this cnt32_to_63 is called atleast once every half period.
When I print out the actual wrap-around time, and using
a year (3600*24*365 seconds) as minumum wrap limit I get an
actual wrap-around of:
sched_clock: using 55 bits @ 8333125 Hz wrap in 416 days
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7c63984b86 (ARM: do not define VMALLOC_END relative to PAGE_OFFSET)
changed VMALLOC_END to be an explicit value. Before this, it was
relative to PAGE_OFFSET and therefore converted to unsigned long
as PAGE_OFFSET is an unsigned long. This introduced the following
build warning. Fix this by changing the explicit defines of
VMALLOC_END to be unsigned long.
CC arch/arm/mm/init.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Uwe Kleine-K <u.kleine-koenig@pengutronix.dee>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change updates the ux500 specific outer cache code to use
the new *_relaxed() I/O accessors.
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It looks to me as if the second value of rate_err_array is intended
to be a decimal 625. However, with a leading 0 it becomes an octal
constant, and as such evaluates to a decimal 405.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 496c185c94 "atl1c: Add support
for Atheros AR8152 and AR8152" added the condition:
if (hw->nic_type == athr_l1c || hw->nic_type == athr_l2c_b)
for enabling OTP CLK, and the condition:
if (hw->nic_type == athr_l1c || hw->nic_type == athr_l2c)
for disabling OTP CLK. Since the two previously defined hardware
types are athr_l1c and athr_l2c, the latter condition appears to be
the correct one. Change the former to match.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to use __GFP_HIGHMEM in several __vmalloc() calls.
In ceph, add the missing flag.
In fib_trie.c, xfrm_hash.c and request_sock.c, using vzalloc() is
cleaner and allows using HIGHMEM pages as well.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VMWare reports that the e1000 driver has a bug when bringing down the
interface, such that interrupts are not disabled in the hardware but the
driver stops reporting that it consumed the interrupt.
The fix is to set the driver's "down" flag later in the routine,
after all the timers and such have exited, preventing the interrupt
handler from being called and exiting early without handling the
interrupt.
CC: Anupam Chanda <anupamc@vmware.com>
CC: stable kernel <stable@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the compiler to better optimize the page table walking code
by avoiding over-complex pmd_addr_end() calculations. These
calculations prevent the compiler spotting that we'll never iterate
over the PMD table, causing it to create double nested loops where
a single loop will do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the balloon driver doesn't stumble over non-RAM pages, we
can enable the extra space for ballooning.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If the user specifies mem= on the kernel command line, some or all
of the extra memory E820 region may be clipped away, so make sure
we don't try to add more extra memory than exists in E820.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Add extra pages in the pseudo-physical address space to the balloon
so we can extend into them later.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Add EXT4_IOC_TRIM ioctl to handle batched discard
fs: Do not dispatch FITRIM through separate super_operation
ext4: ext4_fill_super shouldn't return 0 on corruption
jbd2: fix /proc/fs/jbd2/<dev> when using an external journal
ext4: missing unlock in ext4_clear_request_list()
ext4: fix setting random pages PageUptodate
Filesystem independent ioctl was rejected as not common enough to be in
core vfs ioctl. Since we still need to access to this functionality this
commit adds ext4 specific ioctl EXT4_IOC_TRIM to dispatch
ext4_trim_fs().
It takes fstrim_range structure as an argument. fstrim_range is definec in
the include/linux/fs.h and its definition is as follows.
struct fstrim_range {
__u64 start;
__u64 len;
__u64 minlen;
}
start - first Byte to trim
len - number of Bytes to trim from start
minlen - minimum extent length to trim, free extents shorter than this
number of Bytes will be ignored. This will be rounded up to fs
block size.
After the FITRIM is done, the number of actually discarded Bytes is stored
in fstrim_range.len to give the user better insight on how much storage
space has been really released for wear-leveling.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There was concern that FITRIM ioctl is not common enough to be included
in core vfs ioctl, as Christoph Hellwig pointed out there's no real point
in dispatching this out to a separate vector instead of just through
->ioctl.
So this commit removes ioctl_fstrim() from vfs ioctl and trim_fs
from super_operation structure.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix readdir EOVERFLOW on 32-bit archs
ceph: fix frag offset for non-leftmost frags
ceph: fix dangling pointer
ceph: explicitly specify page alignment in network messages
ceph: make page alignment explicit in osd interface
ceph: fix comment, remove extraneous args
ceph: fix update of ctime from MDS
ceph: fix version check on racing inode updates
ceph: fix uid/gid on resent mds requests
ceph: fix rdcache_gen usage and invalidate
ceph: re-request max_size if cap auth changes
ceph: only let auth caps update max_size
ceph: fix open for write on clustered mds
ceph: fix bad pointer dereference in ceph_fill_trace
ceph: fix small seq message skipping
Revert "ceph: update issue_seq on cap grant"
Some board/card/host configurations are not capable of powering off the
card after boot.
To support such configurations, and to allow smoother transition to
runtime PM behavior, MMC_CAP_POWER_OFF_CARD is added, so hosts need to
explicitly indicate whether it's OK to power off their cards after boot.
SDIO core will enable runtime PM for a card only if that cap is set.
As a result, the card will be powered down after boot, and will only
be powered up again when a driver is loaded (and then it's up to the
driver to decide whether power will be kept or not).
This will prevent sdio_bus_probe() failures with setups that do not
support powering off the card.
Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Reported-and-tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Power off the card in mmc_sdio_detect __before__ a potential error
handler, which completely removes the card, executes, and only if the
card was successfully powered on beforehand.
While we're at it, use the _sync variant of the runtime PM put API, in
order to ensure that the card is left powered off in case an error
occurred, and the card is going to be removed.
Reproduced and tested on the OLPC XO-1.5.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 59365d136d.
It turns out that this can break certain existing user land setups.
Quoth Sarah Sharp:
"On Wednesday, I updated my branch to commit 460781b from linus' tree,
and my box would not boot. klogd segfaulted, which stalled the whole
system.
At first I thought it actually hung the box, but it continued booting
after 5 minutes, and I was able to log in. It dropped back to the
text console instead of the graphical bootup display for that period
of time. dmesg surprisingly still works. I've bisected the problem
down to this commit (commit 59365d136d)
The box is running klogd 1.5.5ubuntu3 (from Jaunty). Yes, I know
that's old. I read the bit in the commit about changing the
permissions of kallsyms after boot, but if I can't boot that doesn't
help."
So let's just keep the old default, and encourage distributions to do
the "chmod -r /proc/kallsyms" in their bootup scripts. This is not
worth a kernel option to change default behavior, since it's so easily
done in user space.
Reported-and-bisected-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcus Meissner <meissner@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Eugene Teo <eugeneteo@kernel.org>
Cc: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix typo in keycode validation supporting large scancodes
Input: aiptek - tighten up permissions on sysfs attributes
Input: sysrq - pass along lone Alt + SysRq
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Disable FBC on Ironlake to save 1W
drm/i915: Take advantage of auto-polling CRT hotplug detection on PCH hardware
drm/i915/crt: Introduce struct intel_crt
drm/i915: Do not hold mutex when faulting in user addresses
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
drm/i915: Retire any pending operations on the old scanout when switching
drm/i915: Fix I2C adapter registration
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (40 commits)
drm/radeon/kms: i2c s/sprintf/snprintf/g for safety
drm/radeon/kms: fix i2c pad masks on rs4xx
drm/ttm: Fix up a theoretical deadlock
drm/radeon/kms: fix tiling info on evergreen
drm/radeon/kms: fix alignment when allocating buffers
drm/vmwgfx: Fix up an error path during bo creation
drm/radeon/kms: register an i2c adapter name for the dp aux bus
drm/radeon/kms/atom: add proper external encoders support
drm/radeon/kms/atom: cleanup and unify DVO handling
drm/radeon/kms: properly power up/down the eDP panel as needed (v4)
drm/radeon/kms/atom: set sane defaults in atombios_get_encoder_mode()
drm/radeon/kms: turn the backlight off explicitly for dpms
drm/radeon/kms: fix typo in r600 cs checker
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
nouveau: Acknowledge HPD irq in handler, not bottom half
drm/nouveau: Fix a few confusions between "chipset" and "card_type".
drm/nouveau: don't expose backlight control when available through ACPI
drm/nouveau/pm: improve memtiming mappings
drm/nouveau: Make PCIE GART size depend on the available RAMIN space.
...
vt6420 has the same FIFO overflow problem as vt6421 when combined with
certain devices. This patch applies the magic fix to vt6420 too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Qvist <q@maq.dk>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix kernel-doc warning for sk_filter_rcu_release():
Warning(net/core/filter.c:586): missing initial short description on line:
* sk_filter_rcu_release: Release a socket filter by rcu_head
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupts are enabled only when open is called on the interface,
Attempting a firmware update operation when interface is down could lead to
partial success or failure of operation. This fix fails the request if
netif_running is false.
Signed-off-by: Sarveshwar Bandi <Sarveshwar.Bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the start of ext4_fill_super, ret is set to -EINVAL, and any failure path
out of that function returns ret. However, the generic_check_addressable
clause sets ret = 0 (if it passes), which means that a subsequent failure (e.g.
a group checksum error) returns 0 even though the mount should fail. This
causes vfs_kern_mount in turn to think that the mount succeeded, leading to an
oops.
A simple fix is to avoid using ret for the generic_check_addressable check,
which was last changed in commit 30ca22c70e.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
After checking the code in 2.6.36,
I found this is missing during multi-component conversion.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Frame buffer compression is broken on Ironlake due to buggy hardware.
Currently it is disabled through chicken bits, but it still consumes
over 1W more than if we simply never attempt to enable the FBC code
paths.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.
The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>