switch the rtc drivers to resource and pass it via platform_device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
we will select now the DBGU used by the soc at Kconfig level
For the DEBUG_LL and early_printk this will allow to select which DBGU to use
this will also allow to select them when multiple SOC are enabled
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
switch the watchdog drivers to resource and pass it via platform_device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin. Create a common
macb_platform_data for macb that both at91 and avr32 can use. In
future we can use this to support other architectures that use the
same IP block with the macb driver.
v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Since 193ab2a607, various AT91 boards don't
register USBA adapters anymore due to depending on a now non-existing
symbol. Fix the symbol name.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: stable@kernel.org
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
In commit fb149f9e28 we introduce ioremap support for static map_io, we do
not need this register entry anymore.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/driver' of git://git.linaro.org/people/arnd/arm-soc:
hw_random: add driver for atmel true hardware random number generator
ARM: at91: at91sam9g45: add trng clock and platform device
MX53 Enable the AHCI SATA on MX53 SMD board
MX53 Enable the AHCI SATA on MX53 LOCO board
MX53 Enable the AHCI SATA on MX53 ARD board
AHCI Add the AHCI SATA feature on the MX53 platforms
Fix pata imx resource
ARM: imx: Define functions for registering PATA
ARM: imx: Add PATA clock support
ARM: imx: Add PATA resources for other i.MX processors
imx: efika: Enable pata.
imx51: add pata clock
imx51: add pata device
Fix up trivial conflict (new selects next to each other from separate
branches for EFIKA_COMMON) in arch/arm/mach-mx5/Kconfig
As a new overcurrent_pin[] array has been added to the at91_usbh_data
structure, those pins must be muxed to work properly. This commit
implements this muxing for all AT91 SoCs that support the AT91 OHCI.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[nicolas.ferre@atmel.com: added i variable declaration for the loop]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
we do not change the clock naming convention so does not need to switch
the AVR32 yet
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
specify the port num via platform_data this will allow to match the clock
with the plaform_dev staticaly
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use a correct udelay value to get bus speed around 100KHz. The udelay
value was most likely copied from the older devices, but the 9g45
is signicantly faster (400MHz, DDR, ..), so a udelay of 2 gives a
bus speed of around 190KHz, which is too fast for some devices.
A udelay value of 5 gives a bus speed of around 90KHz here.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without this patch you will not be able to register the first block
because of the second association call on at91_add_device_tc().
Signed-off-by: Fabian Godehardt <fg@emlix.com>
[nicolas.ferre@atmel.com: change tcb1_clk to fake child clock of tcb0_clk]
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is the at91 specific part of USB host integration. The EHCI high speed
controller has a companion OHCI controller to manage USB full and low speed.
They are sharing the same IRQ line and vbus pin.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The macro for the watchdog has been changed from CONFIG_AT91SAM9_WATCHDOG
to CONFIG_AT91SAM9X_WATCHDOG due to AT91CAP9 chips support
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the support of AC97 on the at91sam9g45 chip series and -ek board.
It will share the code with AVR32 ac97c alsa driver "atmel_ac97c".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the integration of DMA engine driver into at91sam9g45 series
device file.
The associated driver is at_hdmac.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here are the at91 specific files dedicated to the at91sam9g45 series. They
mimic the traditional at91 way of managing chips & boards.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. In
the future, the main board for this 9g45 series will be the
AT91SAM9M10G45-EK (I choose this last name for the board file).
Simple drivers are enabled in _devices and board- files. Newer peripheral
support will be added in future patches.
Incuded peripherals support (for now):
- USART
- SPI
- Ethernet
- NAND flash
- LCD
- gpio/joystick/buttons
- leds and pwm
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
