People do not read the README and seem to like to
unselect the crc32c module even though iscsi_tcp selects
it for them. This patch spits a error that tells the user
that they really do need the module. Hopefully, we will
get fewer people asking about this now.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For a while now, the block layer has seperated max sectors
and max hw sectors. Software iscsi has no limit so this patch
increases max hw sectors, so we can support large pass through
commands.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Dave Miller meantioned that the data buffer in a past
sense fixup patch was not gauranteed to be aligned
properly for ia64. This patch has libiscsi use get_unalinged
to make sure. There are a couple more places in the
digest handling we may need to do this, but we are in the middle
of fixing that code for big endien systems so just the sense
access is fixed here.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
qla4xxx and iscsi_tcp or iser could be creating
sessions at the same time, so make session_nr id
allocation atomic.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's possible that we call iscsi_xmitworker after iscsi_conn_release
which causes a oops. This patch flushes the workqueue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add missing additional sense code and provide pointer to upstream
reference (from Doug Gilbert).
Add missing const (from Michael Tokarev).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the sd.c SCSI logging calls to scmd_printk()/sd_printk()
instead of plain printk().
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make SCSI disk printing more consistent:
- Define sd_printk(), sd_print_sense_hdr() and sd_print_result()
- Move relevant header bits into sd.h
- Remove all the legacy disk_name passing and use scsi_disk pointers
where possible
- Switch printk() lines to the new sd_ functions so that output is
consistent
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch enhances SCSI error printing by:
- Making use of scsi_print_result() in the completion functions.
- Having scmd_printk() output the disk name (when applicable).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clean up constants.c and make result printing more user friendly:
- Refactor the command and sense functions so that the actual
formatting can be called from the various helper functions with the
correct prefix.
- Replace scsi_print_hostbyte() and scsi_print_driverbyte() with
scsi_print_result() which is verbose when CONFIG_SCSI_CONSTANTS is
on.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
An off-by-one bug meant we were always trying to map one too many
scatterlist entries. This was mostly harmless prior to the checks
going in to consistent_sync(), but now causes the kernel to BUG.
Also, powertec.c was missing an assignment to info->ec.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI doesn't want drivers to modify request_bufflen, so keep a
driver-private copy of this in the scsi_pointer structure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] SCSI core: better initialization for sdev->scsi_level
[SCSI] scsi_proc.c: display sdev->scsi_level correctly
[SCSI] megaraid_sas: update version and author info
[SCSI] megaraid_sas: return sync cache call with success
[SCSI] megaraid_sas: replace pci_alloc_consitent with dma_alloc_coherent in ioctl path
[SCSI] megaraid_sas: add bios_param in scsi_host_template
[SCSI] megaraid_sas: do not process cmds if hw_crit_error is set
[SCSI] scsi_transport.h should include scsi_device.h
[SCSI] aic79xx: remove extra newline from info message
[SCSI] scsi_scan.c: handle bad inquiry responses
[SCSI] aic94xx: tie driver to the major number of the sequencer firmware
[SCSI] lpfc: add PCI error recovery support
[SCSI] megaraid: pci_module_init to pci_register_driver
[SCSI] tgt: fix the user/kernel ring buffer interface
[SCSI] sgiwd93: interfacing to wd33c93
[SCSI] wd33c93: Fast SCSI with WD33C93B
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix the various misspellings of "agressive", as well as a couple
other things on the same lines while we're there.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch will affect the CDB in INQUIRY commands sent to LUNs above 0
when LUN-0 reports a scsi_level of 0; the LUN bits will no longer be set
in the second byte of the CDB. This is as it should be. Nevertheless,
it's possible that some wacky device might be adversely affected. I doubt
anyone will complain...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as833) fixes the "SCSI revision" output for
/proc/scsi/scsi. If the scsi_level value is 0 (UNKNOWN), we want it
to show up as "0", not "ffffffff".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
FW does not support SYNCHRONIZE_CACHE cmd. FW flush cache on its own.
So, we just return success from the megasas_queue_command.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replaced pci_alloc_consistent with dma_alloc_coherent from the ioctl path.
This is to avoid situations where ioctl fails for lack of memory
(when system under heavy stress).
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Checks if hw_crit_error is set.
If it is set, we donot process commands.
Checks added in megasas_queue_command and command completion routines.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This extra newline character introduces a completely empty line in dmesg as
the calling function itself adds a newline.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A particular USB device has been reporting short inquiry lengths. The
SCSI code cannot operate properly unless we get an inquiry length of
36 or above (because of the way we parse vendor and product), so
assume at least 36 bytes are valid even if the device reports fewer.
This is wrong, but it's no worse than what we're doing now (using the
garbage beyond the last reported valid byte).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The sequencer firmware file has both a string (currently showing
V17/10c6) and a number (currently set to 1.1). It has become apparent
that Adaptec may issue sequencer firmware in the future which could be
incompatible with the current driver. Therefore, the driver will be
tied to the particular major number of the firmware (i.e. the current
driver will load any 1.x firmware). Additionally, the driver will print
out both the ascii string and the major number, so with this pach the
current firmware will print out
aic94xx: Found sequencer firmware version 1.1 (V17/10c6)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds PCI Error recovery support to the
Emulex Lightpulse Fibrechannel (lpfc) SCSI device driver.
Lightly tested at this point, works.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Bino.Sebastian@Emulex.Com
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patches fixes two bugs in the scsi target infrastructure's
user/kernel interface.
- It wrongly assumes that the ring buffer size of the interface (64KB)
is larger than or equal to the system page size. This patch sets the
ring buffer size to PAGE_SIZE if the system page size is larger.
- It uses PAGE_SIZE in the header file exported to userspace. This
patch removes it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
1) sgiwd93 used to switch off asynchronous mode on the wd33c93, discarding
any "nosync"-requests from the commandline.
But we need to allow "nosync"-requests for selected devices, for example
the Pioneer DVD305S.
(For the curious: this device accepts the SDTR from wd33c93 and success-
fully sends inquiry data in sync mode, but after the data phase in the
inquiry command does an unexpected disconnect, seemingly sending no
"status" or "command complete". Forcing async transfers makes it work
together flawlessly with the wd33c93. Of course, preferable would be, to
implement wd33c93's "resume command" stuff, but that probably will not
come soon.)
2) Maximize benefit from the preceding Fast SCSI patch for wd33c93 by passing
the higher input-clock frequency explicitely. To be applied after the
mentioned wd33c93 patch.
Signed-off-by: peter fuerst <post@pfrst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Attached are patches, which help to utilize more of the WD33C93B SCSI
controller's capabilities.
1) Added/changed all the necessary code to enable Burst Mode DMA. Only
Single Byte DMA was used before.
2) Added/changed all the necessary code to enable Fast-10 SCSI transfers.
3) The original driver inadvertently used a transfer period of 1000-800ns
(the lowest possible transfer rate) for asynchronous data transfers,
instead of the (configurable) default period intended for this purpose,
if the target responded to a SDTR not with a Reject-message, but with
a zero-SDTR. This issue was fixed.
Moreover, in case of a Reject the driver used the default-period's
initialization-value instead of its (maybe smaller) current value. The
missing assignment was added.
4) The driver's commandline- and proc-file-interface was augmented to
handle the new options properly.
The WD33C93 manual, found at
http://www.datasheet.in/datasheet-html/W/D/3/WD33C93B_WesternDigital.pdf.html,
was very helpful.
Signed-off-by: peter fuerst <post@pfrst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits)
[SCSI] zfcp: removed wrong comment
[SCSI] zfcp: use of uninitialized variable
[SCSI] zfcp: Invalid locking order
[SCSI] aic79xx: use dma_get_required_mask()
[SCSI] aic79xx: fix bracket mismatch in unused macro
[SCSI] BusLogic: Replace 'boolean' by 'bool'
[SCSI] advansys: clean up warnings
[SCSI] 53c7xx: brackets fix in uncompiled code
[SCSI] nsp_cs: remove old scsi code
[SCSI] aic79xx: make ahd_match_scb() static
[SCSI] DAC960: kmalloc->kzalloc/Casting cleanups
[SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled
[SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save()
[SCSI] aic94xx: update for v28 firmware
[SCSI] scsi_error: Fix lost EH commands
[SCSI] aic94xx: Add default bus reset handler
[SCSI] aic94xx: Remove TMF result code munging
[SCSI] libsas: Add an LU reset mechanism to the error handler
[SCSI] libsas: Don't BUG when connecting two expanders via wide port
[SCSI] st: fix Tape dies if wrong block size used, bug 7919
...
Simplify the few instances where a call to "get_zeroed_page()" is closely
followed by an unnecessary call to memset() to clear that page.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: chas williams <chas@cmf.nrl.navy.mil>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As originally noted by Frederic Temporelli, the aic79xx supports 64
bit addressing, but the initialization code of the driver is wrong: it
tests the available memory size instead of testing the maximum
available memory address.
This patch uses the correct dma_get_required_mask() macros to
determine the correct addressing method.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Xavier Bru <xavier.bru@bull.net>
CC: Frederic Temporelli <frederic.temporelli@bull.net>
cosmetic fixes
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
