percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Can be used to balance NIC/FCoE traffic distribution.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code could inadvertently skip the post processing of
port information returned from the SNS scan, if any link-flopping
asynchronous-events were received (noticed in FCAL topologies).
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver did not account for non-tape devices needing to employ
proper FCP2 recovery. Driver now checks the FCP2-capable flag
only, rather than using a midlayer-determined flag (TYPE_TAPE).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the hba port gets logged out of the fabric, or other
such transitional state when the physical link is still present,
the driver doesn't receive a loop up asyn event (where the link
data rate currently gets set). Hence send a explicit mailbox command
to get the link rate in such conditions.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix to accommodate a hardware bug in multiqueue mode that does not
work properly when acknowledgement of MSIX Interrupts is disabled.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code would not register FC4 nor FDMI information after a
logical tear-down of an VFC link. Code now triggers registration
date during processing of a 'Report ID Acquisition IOCB', which
is submitted after a FLOGI or FDISC completes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In some case, the MPI and PHY versions when retrieved after the
Execute-FW mailbox-command are incorrect (255.255.255.255).
Instead, query the information after the check for firmware ready
is done in the abort ISP path.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code would inadvertently skip the deferred
fc_remote_port_delete() call for rports hanging off any vport.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In fabric-login based on iop BIT_8 firmware notifies presence of
a FCP2 device and not necessarily a TAPE device. So instead of
setting FCF_TAPE_PRESENT flag there we set it using
scsi_device->type after mid-layer scan recognises "type" of the
device.
It also adds a new flag FCF_FCP2_DEVICE for any future use.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ISPs which support this feature include 23xx and above.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the multiqueue mode fails to work, the driver falls back on single
queue mode. This ensures that the firmware is reinitialized with single
queue options and all the resources are readjusted accordingly.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* To set iiDMA speeds for ISP81XX, bits 5-0 are used whereas for
other older ISPs bits 2-0 are used.
* Pass proper VP index
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure MPS remains in synchronization across all NIC/FCoE
functions after a reset.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ISP24xx and above ISPs perform a RISC reset in
qla24xx_reset_chip(), which is called prior to
qla24xx_chip_diag().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With RSCN states not being kept across qla2x00_configure_loop()
invocations, loop-resync distruptions during fabric-discovery may
cause ports to remain in a lost state. Force state
renegotiation during a follow-on configure-loop iteration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Unlike earlier ISPs, recent ISPs (ISP81xx) can in fact fail this
mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In case the onboard firmware is unable to be read or loaded for
operation, attempt to fallback to a limited-operational firmware
image stored in a different flash region. This will allow a user
to reflash and correct a board with proper operational firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it may be useful during debugging to use a specific firmware
image.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Information present in static table is only valid for pre-ISP25xx
adapters.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware semantics changed for 24xx and above ISPs in their
handling of the specified execution-throttle passed during
firmware initialization. The original codes use of a theoretical
maximum (0xffff, as carried over from earlier ISPs) could in fact
act as a throttle in some circumstances. Now set the value based
of the firmware's own 'resource' (exchange IOCBs) capabilities.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The original code to 'resize request-queues' based on iocb-counts
and employed during early ISP23xx testing was too
overly-pessimistic with regards to latencies in the firmware
pulling requests. Recent ISPs can easily keep up processing a
stream of commands from an abbreviated (effectively, half the
original size) queue.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rather than assuming a particular layout of the data. Applies to
recent ISPs only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
General cleanup of extraneous/legacy crud.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure that an ISP-abort has completed before performing any
update. After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset. This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Given the low-level interface varies from one flash-part
manufacturer to the next, the Flash-Access-Control (FAC) mailbox
command makes the specific flash type transparent to the driver
by encapsulating a basic set of accessor and update routines.
Use these new routines where applicable by querying FAC opcode
get-sector-size at init-time.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reflects layout and format of latest specification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs use this data to configure FCF information.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With recent ISPs loading firmware from flash, a flash-update to
the firmware-image region with a follow-on reset will reload the
new image.
Original caching of data only made sense when firmware was bound
with the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fce_size should be calculated based on the FCE_SIZE #define.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
QLA_* return codes are 'int' in size. There were still several
legacy check-points which assumed a return-code width of 8-bits.
This could cause incorrect assumptions of 'good' status if a
return of QLA_FUNCTION_TIMEOUT.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use minimum value for max vport during firmware initialization in LOOP
topology. Using max vport value from get resource count in LOOP topology
causes firmware initialization failure.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct response-queue-0 processing by instructing the firmware
to run with interrupt-handshaking disabled, similarly to what is
now done for all non-0 response queues. Since all
response-queues now run in the same mode, the driver no longer
needs the hot-path 'is-disabled-HCCR' test.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP81XX parts (including ISP24xx and ISP25xx) could contain a
firmware image within a segment of flash, driver would fallback
to loading this firmware if the request-firmware interface failed
(userspace .bin file). Moving forward, all ISP81XX parts will
ship with a suggested-to-be-used firmware image within flash
which all driver should first attempt to load. If the flash
firmware load fails, the driver will then fallback to loading
firmware via the request-firmware interface (ql8100_fw.bin).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
