We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI 2.x cells used on some 44x SoCs only let us configure the decode
for the low 32-bit of the incoming PLB addresses. The top 4 bits (this
is a 36-bit bus) are hard wired to different values depending on the
specific SoC in use. Our code used to work "by accident" until I added
support for the ISA memory holes and while at it added more validity
checking of the addresses.
This patch should bring it back to working condition. It still relies
on the device-tree being correct but that's somewhat a pre-requisite
for anything to work anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
4xx chips commonly now have multiple PHBs, there is no reason to not
enable PCI domains on them. The main issue with PCI domains is X but
currently its already somewhat busted for other reasons such as the
36-bit physical address space, which I'm fixing separately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch allows the 4xx (conventional) PCI bridge to be disabled
via the device tree. This is needed for 4xx PCI adapter hardware.
Use the PCI node's status property to disable the PCI bridge.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
There's no good reason why a resource_size_t shouldn't just be a
physical address, so simply redefine it in terms of phys_addr_t.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The declaration of total_memory removed. Now including <mm/mmu_decl.h>
instead. Since total_memory is a phys_addr_t which is 64-bit on 44x and
is_power_of_2() works with u32 so I just inlined (size & (size-1)) != 0
instead.
Also this patch fixes default initialization: res->end should be 0x7fffffff
not 0x80000000.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
During recent tests with PCI-E , it has been found the
DRV + De-Emphasis values are not optimum. These new values
are tested thouroughly.
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Feng Kan fkan@amcc.com
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 440EPx/GRx chips don't support PCI MRM commands. Drivers determine this
by looking for a zero value in the PCI cache line size register. However,
some drivers write to this register upon initialization. This can cause
MRMs to be used on these chips, which may cause deadlocks on PLB4.
The workaround implemented here introduces a new indirect_type flag, called
PPC_INDIRECT_TYPE_BROKEN_MRM. This is set in the pci_controller structure in
the pci fixup function for 4xx PCI bridges by determining if the bridge is
compatible with 440EPx/GRx. The flag is checked in the indirect_write_config
function, and forces any writes to the PCI_CACHE_LINE_SIZE register to be
zero, which will disable MRMs for these chips.
A similar workaround has been tested by AMCC on various PCI cards, such as
the Silicon Image ATA card and Intel E1000 GIGE card. Hangs were seen with
the Silicon Image card, and MRMs were seen on the bus with a PCI analyzer.
With the workaround in place, the card functioned properly and only Memory
Reads were seen on the bus with the analyzer.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch add a check to the PPC4xx PCIe driver to detect if the port
is disabled via the device-tree. This is needed for the AMCC Canyonlands
board which has an option to either select 2 PCIe ports or 1 PCIe port
and one SATA port. The SATA port and the 1st PCIe port pins are multiplexed
so we can't start both drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds basic endpoint support to the 4xx PCIe driver.
This is done by checking the device_type property of the PCIe
device node ("pci" for root-complex and "pci-endpoint" for endpoint
configuration).
Note: Currently we map a fixed 64MByte window to PLB address 0 (SDRAM).
This should probably be configurable via a dts property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch fixes a bug, where the PESDRn_UTLSET1 register was setup
wrongly resulting in a non working PCIe port 1. With this fix both
PCIe ports work fine again.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since the arch/powerpc PCI subsystem now does a complete re-assignment of
the resources, we can move from the unconditional PCIe PHY reset to the
conditional version. Now the PHY is only reset, if no link is established yet.
An additional PHY reset (one is already done in U-Boot) leads to problems
with some Atheros PCIe boards and some HP FPGA PCIe designs.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
All this code is needed to properly initialize the 460EX PCIe host
bridge(s). We re-initialize all ports again, even though this has been done
in the bootloader (U-Boot) before. This way we make sure, that we always
run the latest init code in Linux and don't depend on code versions from
U-Boot.
Unfortunately all IBM/AMCC chips currently supported in this PCIe driver need
a different reset-/init-sequence.
Tested on AMCC Canyonlands eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Because of how big mapping the config space is (1M per bus), we limit how
many busses we support for now. In the long run, we could replace that
with something akin to kmap_atomic instead.
This patch changes the limit from currently 16 to 64.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch sets the ibpre flag (Inbound Presence) for the 405EX
in the 4xx PCIe driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds runtime detection of the 440SPe revision A chips. These
chips are equipped with a slighly different PCIe core and need special/
different initialization. The compatible node is changed to
"plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that
can be equipped with both PPC revisions like the AMCC Yucca.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This improves the way the 4xx PCI-E code handles checking for a link
and adds explicit testing of CRS result codes on config space accesses.
This should make it more reliable.
Also, bridges with no link are now still created, though config space
accesses beyond the root complex are filtered. This is one step toward
eventually supporting hotplug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous 2 patches the support for the 4xx PCI Express
cells as found in the 440SPe revA, revB and 405EX.
Unfortunately, due to significant differences between these, and other
interesting "features" of those pieces of HW, the code isn't as simple
as it is for PCI and PCI-X and some of the functions differ significantly
between the 3 implementations. Thus, not only this code can only support
those 3 implementations for now and will refuse to operate on any other,
but there are added ifdef's to avoid the bloat of building a fairly large
amount of code on platforms that don't need it.
Also, this code currently only supports fully initializing root complex
nodes, not endpoint. Some more code will have to be lifted from the
arch/ppc implementation to add the endpoint support, though it's mostly
differences in memory mapping, and the question on how to represent
endpoint mode PCI in the device-tree is thus open.
Many thanks to Stefan Roese for testing & fixing up the 405EX bits !
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous patch the support for the 4xx PCI 2.x
bridges.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support code for the 4xx PCI-X bridge. It also provides
placeholders for the PCI and PCI-E version but they aren't supported
with this patch.
The bridges are configured based on device-tree properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
