Power-up timing
The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled. When this occurs, the P0 port
does not respond to the Channel Access Write command. For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below. The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first. This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.
Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD
[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows the 1-wire bus to autoload the corresponding module
for each slave being attached.
This works similar to bluetooth protocols.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fails, and also add the return value check of
platform_device_add_data().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
De-activating this reading back will effectively half the time required
for a write to the output register.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Sat, Mar 02, 2013 at 10:45:10AM +0100, Sven Geggus wrote:
> This is the bad commit I found doing git bisect:
> 04f482faf5 is the first bad commit
> commit 04f482faf5
> Author: Patrick McHardy <kaber@trash.net>
> Date: Mon Mar 28 08:39:36 2011 +0000
Good job. I was too lazy to bisect for bad commit;)
Reading the code I found problematic kthread_should_stop call from netlink
connector which causes the oops. After applying a patch, I've been testing
owfs+w1 setup for nearly two days and it seems to work very reliable (no
hangs, no memleaks etc).
More detailed description and possible fix is given below:
Function w1_search can be called from either kthread or netlink callback.
While the former works fine, the latter causes oops due to kthread_should_stop
invocation.
This patch adds a check if w1_search is serving netlink command, skipping
kthread_should_stop invocation if so.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Josh Boyer <jwboyer@gmail.com>
Tested-by: Sven Geggus <lists@fuchsschwanzdomain.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 3.0+
Commit 8a1861d997 ("w1-gpio: Simplify & get rid of defines") removed the
compile guards from the device-tree id table, thereby generating a
warning when building without device-tree support.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8a1861d997 ("w1-gpio: Simplify & get rid of defines") changed
(apparently unknowingly) the driver to a hotpluggable platform-device
driver but did not not update the section markers for probe and remove
(to __devinit/exit, which have since been removed). A later commit fixed
the section mismatch for probe, but left remove marked with __exit.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.8
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
Also fixes some whitespace inconsistency in Kconfig and w1_family.h when
DS2408 chip support was added.
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
This fixes the following section mismatch:
WARNING: drivers/w1/masters/w1-gpio.o(.data+0x188): Section mismatch in
reference from the variable w1_gpio_driver to the function
.init.text:w1_gpio_probe()
The variable w1_gpio_driver references
the function __init w1_gpio_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_therm includes some obsolete code to detect bad_roms, this is no
longer relevant.
The retry code is only used for this bad_rom test, however there is a
CRC check that detects a bad read, but does not trigger a retry. This
patch removes all the bad_rom code and uses the CRC check to trigger
retries.
Signed-off-by: David Stevenson <david@avoncliff.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
At the same time, this fixes two faults. First, mdev, the result of
kzalloc, was never freed. Second, on failure of ioremap, 0 was returned.
This has been replaced by -EBUSY, which was the failure value for the call
to request_mem_region, with which the call to ioremap has been combined.
The warning message on failure of ioremap is dropped, because
devm_request_and_ioremap already gives such messages on failure.
Finally, the initial call to platform_get_resource is moved closer to the
call to devm_request_and_ioremap, which takes care of checking whether its
result is NULL, implying that a test on the result of this call to
platform_get_resource is not needed.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This slipped in through the merging of different trees. Remove
__devexit_p() use in the mxc_w1 driver.
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are not available on other architectures, so
let's limit them to omap.
If the driver subsystem maintainers want to build test
system wide changes without building for each target,
it's easy to carry a test patch that just strips out the
depends entries from Kconfig files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no reason to have the OF defines; it complicates the driver.
There's also no need for the funky platform_driver_probe.
Add a few warnings in case there's a failure; helps us find out
what went wrong.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are dealing with mxc_w1 registers.
While at it use dev_err() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using module_platform_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the new i.mx clock framework the mxc_w1 clock is registered as:
clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1.0");
So we do not need to pass "owire" string and can use NULL instead.
While at it, also fix the clock error handling code.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
-----
Changes since v2:
- Add Ack's
Changes since v1:
- Fix clock error handling
drivers/w1/masters/mxc_w1.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Paul Walmsley <paul@pwsan.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my tree,
or in Andrew's (the lis3l driver changes came from his tree last week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3pcACgkQMUfUDdst+ymLswCcDYG9RkRcEdYwT5bOm1zM4IVl
WM0AoLKfC86g6xe4MdS7zROJn7ep/9qu
=zAHk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my
tree, or in Andrew's (the lis3l driver changes came from his tree last
week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (52 commits)
drivers/misc/lis3lv02d/lis3lv02d_i2c.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d: remove lis3lv02d driver DT init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add DT matching table passthru code
drivers/misc/lis3lv02d: add generic DT matching code
lis3lv02d: fix some comments specific to lis331dlh driver
MISC: hpilo, remove pci_disable_device
pcmcia: synclink_cs: fix potential tty NULL dereference
drivers/char/mmtimer.c: Remove useless kfree
drivers/char: removes unnecessary semicolon
char/misc: remove CONFIG_EXPERIMENTAL dependencies
mei: don't print buffer as a string
mei: struct mei_message_data doesn't have to be packed
mei: add error messages for open count errors
misc: use module_spi_driver
tifm: use module_pci_driver
misc/at25, dt: Improve at25 SPI eeprom device tree bindings.
mei: add lynx point pci device ids
mei: fix max number of open handles
mei: rename struct pci_dev *mei_device to mei_pdev
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the process of porting boards to devicetree implemenation, we should
keep information about external circuitry where they belong - the
individual drivers.
This patch adds a way to specify a GPIO to drive the (optional) external
pull-up logic, rather than using a function pointer for that.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add DT bindings to the w1-gpio driver, along with some
documentation on how to use them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let the driver compile everywhere while
also removing unnecessary headers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
