The second clk_deny_idle instance should be clk_allow_idle instead.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A workaround for AMD CPU family 11h erratum 311 might cause that the
P-state Status Register shows a "current P-state" which is larger than
the "current P-state limit" in P-state Current Limit Register. For the
wrong P-state value there is no ACPI _PSS object defined and
powernow-k8/cpufreq can't determine the proper CPU frequency for that
state.
As a consequence this can cause a panic during boot (potentially with
all recent kernel versions -- at least I have reproduced it with
various 2.6.27 kernels and with the current .28 series), as an
example:
powernow-k8: Found 1 AMD Turion(tm)X2 Ultra DualCore Mobile ZM-82 processors (2 \
)
powernow-k8: 0 : pstate 0 (2200 MHz)
powernow-k8: 1 : pstate 1 (1100 MHz)
powernow-k8: 2 : pstate 2 (600 MHz)
BUG: unable to handle kernel paging request at ffff88086e7528b8
IP: [<ffffffff80486361>] cpufreq_stats_update+0x4a/0x5f
PGD 202063 PUD 0
Oops: 0002 [#1] SMP
last sysfs file:
CPU 1
Modules linked in:
Pid: 1, comm: swapper Not tainted 2.6.28-rc3-dirty #16
RIP: 0010:[<ffffffff80486361>] [<ffffffff80486361>] cpufreq_stats_update+0x4a/0\
f
Synaptics claims to have extended capabilities, but I'm not able to read them.<6\
6
RAX: 0000000000000000 RBX: 0000000000000001 RCX: ffff88006e7528c0
RDX: 00000000ffffffff RSI: ffff88006e54af00 RDI: ffffffff808f056c
RBP: 00000000fffee697 R08: 0000000000000003 R09: ffff88006e73f080
R10: 0000000000000001 R11: 00000000002191c0 R12: ffff88006fb83c10
R13: 00000000ffffffff R14: 0000000000000001 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88006fb50740(0000) knlGS:0000000000000000
Unable to initialize Synaptics hardware.
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffff88086e7528b8 CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff88006fb82000, task ffff88006fb816d0)
Stack:
ffff88006e74da50 0000000000000000 ffff88006e54af00 ffffffff804863c7
ffff88006e74da50 0000000000000000 00000000ffffffff 0000000000000000
ffff88006fb83c10 ffffffff8024b46c ffffffff808f0560 ffff88006fb83c10
Call Trace:
[<ffffffff804863c7>] ? cpufreq_stat_notifier_trans+0x51/0x83
[<ffffffff8024b46c>] ? notifier_call_chain+0x29/0x4c
[<ffffffff8024b561>] ? __srcu_notifier_call_chain+0x46/0x61
[<ffffffff8048496d>] ? cpufreq_notify_transition+0x93/0xa9
[<ffffffff8021ab8d>] ? powernowk8_target+0x1e8/0x5f3
[<ffffffff80486687>] ? cpufreq_governor_performance+0x1b/0x20
[<ffffffff80484886>] ? __cpufreq_governor+0x71/0xa8
[<ffffffff80484b21>] ? __cpufreq_set_policy+0x101/0x13e
[<ffffffff80485bcd>] ? cpufreq_add_dev+0x3f0/0x4cd
[<ffffffff8048577a>] ? handle_update+0x0/0x8
[<ffffffff803c2062>] ? sysdev_driver_register+0xb6/0x10d
[<ffffffff8056592c>] ? powernowk8_init+0x0/0x7e
[<ffffffff8048604c>] ? cpufreq_register_driver+0x8f/0x140
[<ffffffff80209056>] ? _stext+0x56/0x14f
[<ffffffff802c2234>] ? proc_register+0x122/0x17d
[<ffffffff802c23a0>] ? create_proc_entry+0x73/0x8a
[<ffffffff8025c259>] ? register_irq_proc+0x92/0xaa
[<ffffffff8025c2c8>] ? init_irq_proc+0x57/0x69
[<ffffffff807fc85f>] ? kernel_init+0x116/0x169
[<ffffffff8020cc79>] ? child_rip+0xa/0x11
[<ffffffff807fc749>] ? kernel_init+0x0/0x169
[<ffffffff8020cc6f>] ? child_rip+0x0/0x11
Code: 05 c5 83 36 00 48 c7 c2 48 5d 86 80 48 8b 04 d8 48 8b 40 08 48 8b 34 02 48\
RIP [<ffffffff80486361>] cpufreq_stats_update+0x4a/0x5f
RSP <ffff88006fb83b20>
CR2: ffff88086e7528b8
---[ end trace 0678bac75e67a2f7 ]---
Kernel panic - not syncing: Attempted to kill init!
In short, aftereffect of the wrong P-state is that
cpufreq_stats_update() uses "-1" as index for some array in
cpufreq_stats_update (unsigned int cpu)
{
...
if (stat->time_in_state)
stat->time_in_state[stat->last_index] =
cputime64_add(stat->time_in_state[stat->last_index],
cputime_sub(cur_time, stat->last_time));
...
}
Fortunately, the wrong P-state value is returned only if the core is
in P-state 0. This fix solves the problem by detecting the
out-of-range P-state, ignoring it, and using "0" instead.
Cc: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: fix sleeping-with-spinlock-held bugs/crashes
- Turn a wrmsr to write the DS_AREA MSR into a wrmsrl.
- Use irqsave variants of spinlocks.
- Do not allocate memory while holding spinlocks.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix DS hw enablement on 64-bit x86
Fix the PEBS record size in the DS configuration.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Replace a macro with a static inline function.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Move the CONFIG guard from the .c file into the makefile.
Reported-by: Andi Kleen <andi-suse@firstfloor.org>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix theoretical option string parsing overflow
Since bridge is unsigned, it would seem better to use simple_strtoul that
simple_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r2@
long e;
position p;
@@
e = simple_strtol@p(...)
@@
position p != r2.p;
type T;
T e;
@@
e =
- simple_strtol@p
+ simple_strtoul
(...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: muli@il.ibm.com
Cc: jdmason@kudzu.us
Cc: discuss@x86-64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix with certain compilers
GCC can decide to use %dil when "r" is used, which is not valid for
setnz.
This bug was brought out by Stephen Rothwell's merging of the
branch tracer into linux-next.
[ Thanks to Uros Bizjak for recommending 'q' over 'Q' ]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Check the model type instead of PCI SSID for detection of the mic types
on Dell laptops with IDT 92HD73xx codecs. In this way, a new laptop
can be tested via model module option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed the quirk string for Dell studio 1535 (the product name wasn't
published at the time the patch was made).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT driver creates "Headphone as Line-Out" switch even if there
is no line-out pins on the machine. For devices only with headpohnes
and speaker-outs, this switch shouldn't be created.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AFG pin power-mapping isn't properly set for the fixed I/O pins
on IDT 92HD* codecs. This resulted in the low power mode after the
boot until any jack detection is executed, thus no output from the
speaker.
This patch fixes the power mapping for the fixed pins, and also fixes
the GPIO bits and digital I/O pin settings properly in stac92xx_ini().
Reference: Novell bnc#446025
https://bugzilla.novell.com/show_bug.cgi?id=446025
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPDIF status bits controls are written via snd_hda_codec_write()
without caching. This causes a regression at resume that the bits
are lost.
Simply replacing it with the cached version fixes the problem.
Reference:
http://lkml.org/lkml/2008/11/24/324
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently the omap McBSP code was cleaned up to get rid of
direct McBSP register tinkering by the drivers. Looks like
lcd_sx1.c never got converted, and now it breaks builds.
It seems the lcd_sx1.c driver is attempting SPI mode, but
doing it in a different way compared to omap_mcbsp_set_spi_mode().
Remove the broken driver, patches welcome to add it back when
done properly by patching both mcbsp.c and lcd_sx1.c.
Cc: Vovan888@gmail.com
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Tony Lindgren <tony@atomide.com>
drm vblank initialization keeps track of the changes in driver-supplied
frame counts across vt switch and mode setting, but only if you let it by
not tearing down the drm vblank structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before we had the notion of pinning objects, we had a kludge around to make
sure all of the objects were still resident in the GTT before we committed
to executing a batch buffer. We don't need this any longer, and it sticks an
error return in the middle of object domain computations that must be
associated with a subsequent flush/invalidate emmission into the ring.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Because we write pipestat before iir, it's possible that a pipestat
interrupt will occur between the pipestat write and the iir write. This
leaves pipestat with an interrupt status not visible in iir. This may cause
an interrupt flood as we never clear the pipestat event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old code was wandering through the active list looking for pinned
buffers; there may be other pinned buffers around. Fortunately, we keep a
count of the total amount of pinned memory and can use that instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead, just warn that bad things are happening and do our best to clean up
the mess without the GPU's help.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IMR masking was a technique recommended for avoiding getting stuck with
no interrupts generated again in MSI mode. It kept new IIR bits from getting
set between the IIR read and the IIR write, which would have otherwise
prevented an MSI from ever getting generated again. However, this caused a
problem for vblank as the IMR mask would keep the pipe event interrupt from
getting reflected in IIR, even after the IMR mask was brought back down.
Instead, just check the state of IIR after we ack the interrupts we're going
to handle, and restart if we didn't get IIR all the way to zero.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ml_ff_playback() uses spin_(un)lock_bh. However this function is
called with interrupts disabled from erase_effect() in
drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom
half handling code. This patch changes this function to just use
spin_lock_irqsave() instead, solving the problem and simplifying
the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Often we do things like put BUG() in the default clause of a case
statement. Since it was not declared __noreturn, this could sometimes
lead to bogus compiler warnings that variables were used
uninitialized.
There is a small problem in that we have to put a magic while(1); loop to
fool GCC into really thinking it is noreturn. This makes the new
BUG() function 3 instructions long instead of just 1, but I think it
is worth it as it is now unnecessary to do extra work to silence the
'used uninitialized' warnings.
I also re-wrote BUG_ON so that if it is given a constant condition, it
just does BUG() instead of loading a constant value in to a register
and testing it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Impact: update documentation
Update to reflect the current state of the tracing framework:
- "none" tracer has been replaced by "nop" tracer
- tracing_enabled must be toggled when changing buffer size
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix mmiotrace overrun tracing
When ftrace framework moved to use the ring buffer facility, the buffer
overrun detection was broken after 2.6.27 by commit
| commit 3928a8a2d9
| Author: Steven Rostedt <rostedt@goodmis.org>
| Date: Mon Sep 29 23:02:41 2008 -0400
|
| ftrace: make work with new ring buffer
|
| This patch ports ftrace over to the new ring buffer.
The detection is now fixed by using the ring buffer API.
When mmiotrace detects a buffer overrun, it will report the number of
lost events. People reading an mmiotrace log must know if something was
missed, otherwise the data may not make sense.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
the use of is_blah() suggests a 1 or 0 return. This assumption is made in
pxa25x_udc code such as:
dev->vbus = is_vbus_present();
where dev->vbus is a bitfield. This fix allows pxa25x_udc_probe to correctly
detect vbus. Other changes were to make its use consistent in the rest of
the code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: fix MSIx not enough irq numbers available regression
The manual revert of the sparse_irq patches missed to bring the number
of possible irqs back to the .27 status. This resulted in a regression
when two multichannel network cards were placed in a system with only
one IO_APIC - causing the networking driver to not have the right
IRQ and the device not coming up.
Remove the dynamic allocation logic leftovers and simply return
NR_IRQS in probe_nr_irqs() for now.
Fixes: http://lkml.org/lkml/2008/11/19/354
Reported-by: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jesper Dangaard Brouer <hawk@diku.dk>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Impact: prettify /proc/lockdep_info
Just feel odd that not all lines of lockdep info are aligned.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make output of stack_trace complete if buffer overruns
When read buffer overruns, the output of stack_trace isn't complete.
When printing records with seq_printf in t_show, if the read buffer
has overruned by the current record, then this record won't be
printed to user space through read buffer, it will just be dropped in
this printing.
When next printing, t_start should return the "*pos"th record, which
is the one dropped by previous printing, but it just returns
(m->private + *pos)th record.
Here we use a more sane method to implement seq_operations which can
be found in kernel code. Thus we needn't initialize m->private.
About testing, it's not easy to overrun read buffer, but we can use
seq_printf to print more padding bytes in t_show, then it's easy to
check whether or not records are lost.
This commit has been tested on both condition of overrun and non
overrun.
Signed-off-by: Liming Wang <liming.wang@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added STAC_DELL_M4_3 quirk for Dell systems, also reorganized the
board config switch to assign number of digital muxes, microphones,
and SPDIF muxes via the PCI quirk defined.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the following sparse warnings:
sound/sound_core.c:460:2: warning: returning void-valued expression
sound/sound_core.c:477:2: warning: returning void-valued expression
sound/sound_core.c:510:5: warning: symbol 'soundcore_open' was not
declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
Currently, we can end up in an infinite loop if we get a signal
while the kernel has faulted in spufs_ps_fault. Eg:
alarm(1);
write(fd, some_spu_psmap_register_address, 4);
- the write's copy_from_user will fault on the ps mapping, and
signal_pending will be non-zero. Because returning from the fault
handler will never clear TIF_SIGPENDING, so we'll just keep faulting,
resulting in an unkillable process using 100% of CPU.
This change returns VM_FAULT_SIGBUS if there's a fatal signal pending,
letting us escape the loop.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ACE1001 patch for cp2101.c
USB: usbmon: fix read(2)
USB: gadget rndis: send notifications
USB: gadget rndis: stop windows self-immolation
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
USB: storage: updates unusual_devs entry for the Nokia 6300
usb: musb: fix bug in musb_schedule
USB: fix SB700 usb subsystem hang bug
