When injecting DRAM ECC errors (F3xBC_x8), EccVector[15:0] is a bitmask
of which bits should be error injected when written to and holds the
payload of 16-bit DRAM word when read, respectively.
Add /sysfs members to show the DRAM ECC section/word/vector.
Fail wrong injection values entered over /sysfs instead of truncating
them.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On Fam10h and above, F1x[1, 0][7C:40] are DRAM Base/Limit registers
which specify the destination node of a DRAM address. Those address
boundaries are being extracted into ->dram_base[] and ->dram_limit[].
Correct the extraction masks to match the respective address bits.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Different processor families support a different number of chip selects.
Handle this in a family-dependent way with the proper values assigned at
init time (see amd64_set_dct_base_and_mask).
Remove _DCSM_COUNT defines since they're used at one place and originate
from public documentation.
CC: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This allows the errors to be further decoded and mapped to csrows.
Tested with ECC debug dimms and an Rev F cpu based system.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The check when DRAM interleaving is enabled should be done against the
pvt->dram_IntlvSel field and not against the ->dram_limit.
Simplify first loop and fixup printk formatting while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The pvt->dram_IntlvEn saves the 3 "Interleave Enable" bits already
right-shifted by 8 so the check in find_mc_by_sys_addr() by shifting the
values to the left 8 bits is wrong.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
K8 DRAM base and limit addresses from F1x40 +8*i and F1x44 + 8*i, where
i in (0..7) are both bits 39-24 and therefore the shifting should be
done by 24 and not by 8.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Allocate memory statically for 8-node machines max for simplicity
instead of relying on MAX_NUMNODES which is 0 on !CONFIG_NUMA builds.
Spotted by Jan Beulich.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Since patch_alc268() doesn't call set_capture_mixer() (due to its h/w
design different from other siblings), it needs to call fixup_automic_adc()
explicitly to set up the auto-mic routing. Otherwise the indices for
int/ext mics aren't set properly.
Reference: Novell bnc#544899
http://bugzilla.novell.com/show_bug.cgi?id=544899
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 24df31acaf.
The root cause of reported system hangs was (now fixed) sis5513 bug
and not "ide: try to use PIO Mode 0 during probe if possible" change
(commit 6029336426) so the revert was
incorrect (it simply replaced one regression with the other one).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear prefetch setting before potentially (re-)enabling it in
config_drive_art_rwp() so the transition of the device type on
the port from ATA to ATAPI (i.e. during warm-plug operation)
is handled correctly.
This is a really old bug (it probably goes back to very early
days of the driver) but it was only affecting warm-plug operation
until the recent "ide: try to use PIO Mode 0 during probe if
possible" change (commit 6029336426).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: David Fries <david@fries.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2e21c9610 had unfortunate side
effects with cpufreq governors on some systems.
If the system did not switch into NOHZ mode ts->inidle is not set when
tick_nohz_stop_sched_tick() is called from the idle routine. Therefor
all subsequent calls from irq_exit() to tick_nohz_stop_sched_tick()
fail to call tick_nohz_start_idle(). This results in bogus idle
accounting information which is passed to cpufreq governors.
Set the inidle flag unconditionally of the NOHZ active state to keep
the idle time accounting correct in any case.
[ tglx: Added comment and tweaked the changelog ]
Reported-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: Steven Noonan <steven@uplinklabs.net>
Cc: stable@kernel.org
LKML-Reference: <1254907901.30157.93.camel@eenurkka-desktop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Only 128 buffer descriptors are supported in the core. Limit the
number in case we have more memory.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enabled the ethoc to allocate system memory as buffer
when there is no dedicated buffer memory.
Some hardware designs may not have dedicated buffer memory such as
on chip or off chip SRAM. In this case, only one memory resource is
supplied in the platform data instead of two. Then a DMA buffer can
be allocated from system memory and used for the transfer.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.
The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer address in buffer descriptors is physical address. The
pointer that processor used to access packet is virtual address.
Though the higher bits of pointer address used by the MAC may be
truncated to zero in special case, it is not always true in larger
designs.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be max() instead of min(). Use 1/4 of available
descriptors for tx, and there should be at least 2 tx
descriptors.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT.
in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all pasemi mac interfaces can have a phy attached.
For example, XAUI has no phy and phydev is NULL for it.
In this case ethtool get settings causes kernel crash.
Fix it by returning -EOPNOTSUPP if there's no PHY attached.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was getting ribbed about this earlier, so I figured I'd make it
official. Add myself as the maintainer of the drop monitor bits, so
people don't just gripe at Dave when it breaks (I'm sure it will never
break, but just in case :) ).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock. The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like a typo, FUTEX_WAKE_BITS should be FUTEX_WAIT_BITSET.
Signed-off-by: Anton Blanchard <anton@samba.org>
LKML-Reference: <20091007001358.GE16073@kryten>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This fixes a bug with arp_notify.
If arp_notify is enabled, kernel will crash if address is changed
and no IP address is assigned.
http://bugzilla.kernel.org/show_bug.cgi?id=14330
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the big Kconfig cache split/rename missed one spot in the SMP
cache lock headers.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The cplbinfo was using d_path() to figure out which cpu/cplb was being
parsed. As Al pointed out, this isn't exactly reliable as it assumes the
static VFS path to be unchanged, and it's just poor form. So use the
proc_create_data() to properly (and internally) pass the exact cpu/cplb
requested to the parser function.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The asm/irq.h header uses anomaly defines, but doesn't make sure to
explicitly include the anomaly header for them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.
It also removes:
- verbose GPL text(refer to the top level ./COPYING file)
- file names (you are looking at the file)
- bug url (it's in the ./MAINTAINERS file)
- "or later" on GPL-2, when we did not have that right
It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert Blackfin to use GENERIC_TIME via the arch_getoffset()
infrastructure, reducing the amount of arch specific code we need to
maintain.
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Before this patch, all of the rcu_node structures were in the same lockdep
class, so that lockdep would complain when rcu_preempt_offline_tasks()
acquired the root rcu_node structure's lock while holding one of the leaf
rcu_nodes' locks.
This patch changes rcu_init_one() to use a separate
spin_lock_init() for the root rcu_node structure's lock than is
used for that of all of the rest of the rcu_node structures, which
puts the root rcu_node structure's lock in its own lockdep class.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: akpm@linux-foundation.org
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <12548908983277-git-send-email->
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current interaction between RCU and CPU hotplug requires that
RCU block in CPU notifiers waiting for callbacks to drain.
This can be greatly simplified by having each CPU relinquish its
own callbacks, and for both _rcu_barrier() and CPU_DEAD notifiers
to adopt all callbacks that were previously relinquished.
This change also eliminates the possibility of certain types of
hangs due to the previous practice of waiting for callbacks to be
invoked from within CPU notifiers. If you don't every wait, you
cannot hang.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: akpm@linux-foundation.org
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <1254890898456-git-send-email->
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add kerneldoc comments to some functions in the Gigaset driver.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump payload data consistently only when DEBUG_STREAM_DUMP debug bit
is set.
Impact: debugging aid
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Gigaset base stops responding, try resetting the USB
connection to recover.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear out pending command that got rejected with 'ERROR' response.
This fixes the bug where unloading the driver module would hang
with the message: "gigaset: not searching scheduled commands: busy"
after a device communication error.
Impact: error handling bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention in the driver load announcement whether the driver was built
with debugging messages enabled, to facilitate support.
Impact: informational message
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop the remainder of an URB if an isochronous frame has an error.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code of the Gigaset driver assumes that sk_buff-s coming
from the ISDN4Linux subsystem are always linear. Explicitly
calling skb_linearize() is cheap if they are, but much more
robust in case they ever aren't.
Impact: robustness improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signal D channel disconnect in a few cases where it was missed,
including when an incoming call is disconnected before it was
accepted.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being able to change the debugmode module parameter of capidrv on the
fly is quite useful for debugging and doesn't do any harm.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places, capidrv sends a CAPI message to the ISDN
device and then updates its internal state accordingly.
If the response message from the device arrives before the
state is updated, it may be rejected or processed incorrectly.
Avoid these races by updating the state before emitting the
message.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Info values in the 0x00xx range are defined in the CAPI standard
as "Informational, message processed successfully". Therefore a
CONNECT_B3_CONF message with an Info value in that range should
open an NCCI just as with Info==0.
Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Note that send_message() may be called in interrupt context.
- Describe the storage of CAPI messages and payload data in SKBs.
- Add more details to the description of the _cmsg structure.
- Describe kernelcapi debugging output.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
* use 8 clk setting for active clocks == 7 (was 12 clk)
* use 12 clk setting for active clocks > 12 (was 8 clk)
* do 66MHz bus fixup before mapping active clocks
* fix setup of PIO command timings
Acked-by: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
