Performing a dummy read ensures that the register write operation is fully
completed, mitigating any potential bus delays that could otherwise impact
the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to
control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application
sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on
a delay function to ensure the clock frequency does not exceed 1 MHz.
However, this can lead to rapid toggling of the GPIO because the write
operation is POSTed and does not wait for a bus acknowledgment.
Fixes: 361b79119a ("gpio: Add Aspeed driver")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that pinctrl_gpio_set_config() is no longer used, let's drop the
'_new' suffix from its improved variant.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that pinctrl_gpio_free()() is no longer used, let's drop the '_new'
suffix from its improved variant.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that pinctrl_gpio_request() is no longer used, let's drop the '_new'
suffix from its improved variant.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Replace the pinctrl helpers taking the global GPIO number as argument
with the improved variants that instead take a pointer to the GPIO chip
and the controller-relative offset.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.
Fixes: 5ae4cb94b3 ("gpio: aspeed: Add debounce support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver was implemented in a way that made the irqchip optional, if a
irq was not present in the device tree. However, all of the device trees
have always had an irq, so the optional-ness has never been used.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Do not imply that some of the generic headers may be always included.
Instead, include explicitly what we are direct user of.
While at it, sort headers alphabetically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The gpio-aspeed driver implements an irq_chip which need to be invoked
from hardirq context. Since spin_lock() can sleep with PREEMPT_RT, it is
no longer legal to invoke it while interrupts are disabled.
This also causes lockdep to complain about:
[ 0.649797] [ BUG: Invalid wait context ]
because aspeed_gpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
GPIO_T is mapped to the most significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_T is input only. All
the other bits need to be 1 because GPIO_Q/R/S support both input and
output modes.
Fixes: ab4a85534c ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the
Spreadtrum driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode
for the character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for
bit manipulation in the PCA953x driver.
-----BEGIN PGP SIGNATURE-----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=295T
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.
NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 1.8V GPIO pins.
As the register names for both controllers are the same and the 36 1.8V
GPIOs and the first 36 of the 3.3V GPIOs are all bidirectional, we can
use the same configuration struct and use the ngpio property to
differentiate between the two sets of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906063737.15428-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the ngpio property from the device tree if it exists. If it doesn't
then fallback to the hardcoded value in the config.
This is in preparation for adding ast2600 support. The ast2600 SoC has
two GPIO controllers and so requires two instances of the GPIO driver.
We use the ngpio property to different between them as they have
different numbers of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062727.13521-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is in preparation for adding ast2600 support. The ast2600 SoC
requires two instances of the GPIO driver as it has two GPIO
controllers. Each instance needs it's own irqchip.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062644.13445-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current calculation for the number of GPIO banks is only correct if
the number of GPIOs is a multiple of 32 (if there were 31 GPIOs we would
currently say there are 0 banks, which is incorrect).
Fixes: 361b79119a ('gpio: Add Aspeed driver')
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190906062623.13354-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.d.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20190809125515.19094-1-linus.walleij@linaro.org
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case devm_kzalloc, the patch returns ENOMEM to avoid potential
NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Remove duplicated assignment statement from aspeed_gpio_probe() function.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gcc cannot always see that BUG_ON(1) is guaranteed to not
return, so we get a warning message in some configurations:
drivers/gpio/gpio-aspeed.c: In function 'bank_reg':
drivers/gpio/gpio-aspeed.c:244:1: error: control reaches end of non-void function [-Werror=return-type]
Using a plain BUG() is easier here and avoids the problem.
Fixes: 44ddf559d5 ("gpio: aspeed: Rework register type accessors")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the Aspeed chip, the GPIOs can be under control of the ARM
chip or of the ColdFire coprocessor. (There's a third command
source, the LPC bus, which we don't use or support yet).
The control of which master is allowed to modify a given
GPIO is per-bank (8 GPIOs).
Unfortunately, systems already exist for which we want to
use GPIOs of both sources in the same bank.
This provides an API exported by the gpio-aspeed driver
that an aspeed coprocessor driver can use to "grab" some
GPIOs for use by the coprocessor, and allow the coprocessor
driver to provide callbacks for arbitrating access.
Once at least one GPIO of a given bank has been "grabbed"
by the coprocessor, the entire bank is marked as being
under coprocessor control. It's command source is switched
to the coprocessor.
If the ARM then tries to write to a GPIO in such a marked bank,
the provided callbacks are used to request access from the
coprocessor driver, which is responsible to doing whatever
is necessary to "pause" the coprocessor or prevent it from
trying to use the GPIOs while the ARM is doing its accesses.
During that time, the command source for the bank is temporarily
switched back to the ARM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the definitions for the command source registers
and a helper to set them.
Those registers allow to control which bus master on the
SoC is allowed to modify a given bank of GPIOs and will
be used by subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed GPIO hardware has a quirk: the value register, for an
output GPIO, doesn't contain the last value written (the write
latch content) but the sampled input value.
This means that when reading back shortly after writing, you can
get an incorrect value as the input value is delayed by a few
synchronizers.
The HW supports a separate read-only register "Data Read Register"
which allows you to read the write latch instead.
This adds the definition for it, and uses it for the initial
population of the GPIO value cache. It will be used more in
subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use a single accessor function for all register types instead
of several spread around. This will make it easier/cleaner
to introduce new registers and keep the mechanism in one
place.
The big switch/case is optimized at compile time since the
switch value is a constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with.
Kudos to Laura Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare
dwapb driver.
Misc:
- Random cleanups, right header files in the drivers, some
size optimizations etc.
-----BEGIN PGP SIGNATURE-----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=Ly/0
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.18 development cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with. Kudos to Laura
Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare dwapb
driver.
Misc:
- Random cleanups, right header files in the drivers, some size
optimizations etc"
* tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpio: davinci: fix build warning when !CONFIG_OF
gpio: dwapb: Fix rework support for 1 interrupt per port A GPIO
gpio: pxa: Include the right header
gpio: pl061: Include the right header
gpio: pch: Include the right header
gpio: pcf857x: Include the right header
gpio: pca953x: Include the right header
gpio: palmas: Include the right header
gpio: omap: Include the right header
gpio: octeon: Include the right header
gpio: mxs: Switch to SPDX identifier
gpio: Remove VLA from stmpe driver
gpio: mxc: Switch to SPDX identifier
gpio: mxc: add clock operation
gpio: Remove VLA from gpiolib
gpio: aspeed: Use a cache of output data registers
gpio: aspeed: Set output latch before changing direction
gpio: pca953x: fix address calculation for pcal6524
gpio: pca953x: define masks for addressing common and extended registers
gpio: pca953x: set the PCA_PCAL flag also when matching by DT
...
The current driver does a read/modify/write of the output
registers when changing a bit in __aspeed_gpio_set().
This is sub-optimal for a couple of reasons:
- If any of the neighbouring GPIOs (sharing the shared
register) isn't (yet) configured as an output, it will
read the current input value, and then apply it to the
output latch, which may not be what the user expects. There
should be no bug in practice as aspeed_gpio_dir_out() will
establish a new value but it's not great either.
- The GPIO block in the aspeed chip is clocked rather
slowly (typically 25Mhz). That extra MMIO read halves the maximum
speed at which we can toggle the GPIO.
This provides a significant performance improvement to the GPIO
based FSI master.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In aspeed_gpio_dir_out(), we need to establish the new output
value in the output latch *before* we change the direction
to output in order to avoid a glitch on the output line if
the previous value of the latch was different.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The unmask function disables all interrupts in a bank when unmasking an
interrupt. Only disable the given interrupt.
Cc: stable@vger.kernel.org
Signed-off-by: Govert Overgaauw <govert.overgaauw@prodrive-technologies.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The test should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new pinconf parameter for state persistence to expose the
associated capability of the Aspeed GPIO controller.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
HPLL is in fact not the clock we need. Remove the description of which clock we
failed to find a phandle to in order to avoid any further error.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We warn the user at driver probe time that debouncing is disabled.
However, if they request debouncing later on we print a confusing error
message:
gpio_aspeed 1e780000.gpio: Failed to convert 5000us to cycles at 0Hz: -524
Instead bail out when the clock is not present.
Fixes: 5ae4cb94b3 (gpio: aspeed: Add debounce support)
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per the datasheet, manage the IO and value states to implement
open-source/open-drain, but do this by falling back to gpiolib's
emulation.
This commit simply makes the behaviour explicit for clarity, rather than
relying on the implicit return of -ENOTSUPP to trigger the emulation.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each GPIO in the Aspeed GPIO controller can choose one of four input
debounce states: to disable debouncing for an input, or select from one
of three programmable debounce timer values. Each GPIO in a
four-bank-set is assigned one bit in each of two debounce configuration
registers dedicated to the set, and selects a debounce state by
configuring the two bits to select one of the four options.
The limitation on debounce timer values is managed by mapping offsets
onto a configured timer value and keeping count of the number of users
a timer has. Timer values are configured on a first-come-first-served
basis.
A small twist in the hardware design is that the debounce configuration
register numbering is reversed with respect to the binary representation
of the debounce timer of interest (i.e. debounce register 1 represents
bit 1, and debounce register 2 represents bit 0 of the timer numbering).
Tested on an AST2500EVB with additional inspection under QEMU's
romulus-bmc machine.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
