dma.c defined function plat_swiotlb_setup, which is declared in
bootinfo.h.
Fixes warning:
arch/mips/loongson64/dma.c:25:13: warning: no previous prototype for ‘plat_swiotlb_setup’ [-Wmissing-prototypes]
25 | void __init plat_swiotlb_setup(void)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Pass a boolean flag to indicate if swiotlb needs to be enabled based on
the addressing needs, and replace the verbose argument with a set of
flags, including one to force enable bounce buffering.
Note that this patch removes the possibility to force xen-swiotlb use
with the swiotlb=force parameter on the command line on x86 (arm and
arm64 never supported that), but this interface will be restored shortly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
The __phys_to_dma vs phys_to_dma distinction isn't exactly obvious. Try
to improve the situation by renaming __phys_to_dma to
phys_to_dma_unencryped, and not forcing architectures that want to
override phys_to_dma to actually provide __phys_to_dma.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
There is no harm in just always clearing the SME encryption bit, while
significantly simplifying the interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
In the current market, the most used bridge chip on the Loongson platform
are RS780E and LS7A, the RS780E bridge chip is already supported by the
mainline kernel.
If use the default implementation of __phys_to_dma() and __dma_to_phys()
in dma-direct.h when CONFIG_ARCH_HAS_PHYS_TO_DMA is not set, it works
well used with LS7A on the Loongson single-way and multi-way platform,
and also works well used with RS780E on the Loongson single-way platform,
but the DMA address will be wrong on the non-node0 used with RS780E on
the Loongson multi-way platform.
Just as the description in the code comment, the devices get node id from
40 bit of HyperTransport bus, so we extract 2 bit node id (bit 44~45) from
48 bit address space of Loongson CPU and embed it into HyperTransport bus
(bit 37-38), this operation can be done only at the software level used
with RS780E on the Loongson multi-way platform, because it has no hardware
function to translate address of node id, this is a hardware compatibility
problem.
Device
|
| DMA address
|
Host Bridge
|
| HT bus address (40 bit)
|
CPU
|
| physical address (48 bit)
|
RAM
The LS7A has dma_node_id_offset field in the DMA route config register,
the hardware can use the dma_node_id_offset to translate address of
node id automatically, so we can get correct address when just use the
dma_pfn_offset field in struct device.
For the above reasons, in order to maintain downward compatibility
to support the RS780E bridge chip, it is better to use the platform
dependent implementation of __phys_to_dma() and __dma_to_phys().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
